ARM: at91/USB host: specify and handle properly vbus_pin_active_low

Due to an error while handling vbus_pin_active_low in ohci-at91 driver,
the specification of this property was not good in devices/board files.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: stable <stable@vger.kernel.org>         [3.2+]

arch/arm/mach-at91/at91sam9263_devices.c

@@ -72,7 +72,8 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data)
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
 		if (gpio_is_valid(data->vbus_pin[i]))
-			at91_set_gpio_output(data->vbus_pin[i], 0);
+			at91_set_gpio_output(data->vbus_pin[i],
+					     data->vbus_pin_active_low[i]);
 	}
 
 	/* Enable overcurrent notification */

arch/arm/mach-at91/at91sam9g45_devices.c

@@ -127,7 +127,8 @@ void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data)
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
 		if (gpio_is_valid(data->vbus_pin[i]))
-			at91_set_gpio_output(data->vbus_pin[i], 0);
+			at91_set_gpio_output(data->vbus_pin[i],
+					     data->vbus_pin_active_low[i]);
 	}
 
 	/* Enable overcurrent notification */
@@ -188,7 +189,8 @@ void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data)
 	/* Enable VBus control for UHP ports */
 	for (i = 0; i < data->ports; i++) {
 		if (gpio_is_valid(data->vbus_pin[i]))
-			at91_set_gpio_output(data->vbus_pin[i], 0);
+			at91_set_gpio_output(data->vbus_pin[i],
+					     data->vbus_pin_active_low[i]);
 	}
 
 	usbh_ehci_data = *data;

arch/arm/mach-at91/board-sam9263ek.c

@@ -74,6 +74,7 @@ static void __init ek_init_early(void)
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
 	.vbus_pin	= { AT91_PIN_PA24, AT91_PIN_PA21 },
+	.vbus_pin_active_low = {1, 1},
 	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 

arch/arm/mach-at91/board-sam9m10g45ek.c

@@ -71,6 +71,7 @@ static void __init ek_init_early(void)
 static struct at91_usbh_data __initdata ek_usbh_hs_data = {
 	.ports		= 2,
 	.vbus_pin	= {AT91_PIN_PD1, AT91_PIN_PD3},
+	.vbus_pin_active_low = {1, 1},
 	.overcurrent_pin= {-EINVAL, -EINVAL},
 };