Commit cd26d72d authored by Dan Murphy's avatar Dan Murphy Committed by David S. Miller

net: phy: dp83867: Add speed optimization feature

Set the speed optimization bit on the DP83867 PHY.
This feature can also be strapped on the 64 pin PHY devices
but the 48 pin devices do not have the strap pin available to enable
this feature in the hardware.  PHY team suggests to have this bit set.

With this bit set the PHY will auto negotiate and report the link
parameters in the PHYSTS register.  This register provides a single
location within the register set for quick access to commonly accessed
information.

In this case when auto negotiation is on the PHY core reads the bits
that have been configured or if auto negotiation is off the PHY core
reads the BMCR register and sets the phydev parameters accordingly.

This Giga bit PHY can throttle the speed to 100Mbps or 10Mbps to accomodate a
4-wire cable.  If this should occur the PHYSTS register contains the
current negotiated speed and duplex mode.

In overriding the genphy_read_status the dp83867_read_status will do a
genphy_read_status to setup the LP and pause bits.  And then the PHYSTS
register is read and the phydev speed and duplex mode settings are
updated.
Signed-off-by: default avatarDan Murphy <dmurphy@ti.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent feb5d98e
......@@ -14,6 +14,7 @@
#include <linux/delay.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/bitfield.h>
#include <dt-bindings/net/ti-dp83867.h>
......@@ -21,6 +22,7 @@
#define DP83867_DEVADDR 0x1f
#define MII_DP83867_PHYCTRL 0x10
#define MII_DP83867_PHYSTS 0x11
#define MII_DP83867_MICR 0x12
#define MII_DP83867_ISR 0x13
#define DP83867_CFG2 0x14
......@@ -118,6 +120,24 @@
#define DP83867_IO_MUX_CFG_CLK_O_SEL_MASK (0x1f << 8)
#define DP83867_IO_MUX_CFG_CLK_O_SEL_SHIFT 8
/* PHY STS bits */
#define DP83867_PHYSTS_1000 BIT(15)
#define DP83867_PHYSTS_100 BIT(14)
#define DP83867_PHYSTS_DUPLEX BIT(13)
#define DP83867_PHYSTS_LINK BIT(10)
/* CFG2 bits */
#define DP83867_DOWNSHIFT_EN (BIT(8) | BIT(9))
#define DP83867_DOWNSHIFT_ATTEMPT_MASK (BIT(10) | BIT(11))
#define DP83867_DOWNSHIFT_1_COUNT_VAL 0
#define DP83867_DOWNSHIFT_2_COUNT_VAL 1
#define DP83867_DOWNSHIFT_4_COUNT_VAL 2
#define DP83867_DOWNSHIFT_8_COUNT_VAL 3
#define DP83867_DOWNSHIFT_1_COUNT 1
#define DP83867_DOWNSHIFT_2_COUNT 2
#define DP83867_DOWNSHIFT_4_COUNT 4
#define DP83867_DOWNSHIFT_8_COUNT 8
/* CFG3 bits */
#define DP83867_CFG3_INT_OE BIT(7)
#define DP83867_CFG3_ROBUST_AUTO_MDIX BIT(9)
......@@ -287,6 +307,126 @@ static int dp83867_config_intr(struct phy_device *phydev)
return phy_write(phydev, MII_DP83867_MICR, micr_status);
}
static int dp83867_read_status(struct phy_device *phydev)
{
int status = phy_read(phydev, MII_DP83867_PHYSTS);
int ret;
ret = genphy_read_status(phydev);
if (ret)
return ret;
if (status < 0)
return status;
if (status & DP83867_PHYSTS_DUPLEX)
phydev->duplex = DUPLEX_FULL;
else
phydev->duplex = DUPLEX_HALF;
if (status & DP83867_PHYSTS_1000)
phydev->speed = SPEED_1000;
else if (status & DP83867_PHYSTS_100)
phydev->speed = SPEED_100;
else
phydev->speed = SPEED_10;
return 0;
}
static int dp83867_get_downshift(struct phy_device *phydev, u8 *data)
{
int val, cnt, enable, count;
val = phy_read(phydev, DP83867_CFG2);
if (val < 0)
return val;
enable = FIELD_GET(DP83867_DOWNSHIFT_EN, val);
cnt = FIELD_GET(DP83867_DOWNSHIFT_ATTEMPT_MASK, val);
switch (cnt) {
case DP83867_DOWNSHIFT_1_COUNT_VAL:
count = DP83867_DOWNSHIFT_1_COUNT;
break;
case DP83867_DOWNSHIFT_2_COUNT_VAL:
count = DP83867_DOWNSHIFT_2_COUNT;
break;
case DP83867_DOWNSHIFT_4_COUNT_VAL:
count = DP83867_DOWNSHIFT_4_COUNT;
break;
case DP83867_DOWNSHIFT_8_COUNT_VAL:
count = DP83867_DOWNSHIFT_8_COUNT;
break;
default:
return -EINVAL;
};
*data = enable ? count : DOWNSHIFT_DEV_DISABLE;
return 0;
}
static int dp83867_set_downshift(struct phy_device *phydev, u8 cnt)
{
int val, count;
if (cnt > DP83867_DOWNSHIFT_8_COUNT)
return -E2BIG;
if (!cnt)
return phy_clear_bits(phydev, DP83867_CFG2,
DP83867_DOWNSHIFT_EN);
switch (cnt) {
case DP83867_DOWNSHIFT_1_COUNT:
count = DP83867_DOWNSHIFT_1_COUNT_VAL;
break;
case DP83867_DOWNSHIFT_2_COUNT:
count = DP83867_DOWNSHIFT_2_COUNT_VAL;
break;
case DP83867_DOWNSHIFT_4_COUNT:
count = DP83867_DOWNSHIFT_4_COUNT_VAL;
break;
case DP83867_DOWNSHIFT_8_COUNT:
count = DP83867_DOWNSHIFT_8_COUNT_VAL;
break;
default:
phydev_err(phydev,
"Downshift count must be 1, 2, 4 or 8\n");
return -EINVAL;
};
val = DP83867_DOWNSHIFT_EN;
val |= FIELD_PREP(DP83867_DOWNSHIFT_ATTEMPT_MASK, count);
return phy_modify(phydev, DP83867_CFG2,
DP83867_DOWNSHIFT_EN | DP83867_DOWNSHIFT_ATTEMPT_MASK,
val);
}
static int dp83867_get_tunable(struct phy_device *phydev,
struct ethtool_tunable *tuna, void *data)
{
switch (tuna->id) {
case ETHTOOL_PHY_DOWNSHIFT:
return dp83867_get_downshift(phydev, data);
default:
return -EOPNOTSUPP;
}
}
static int dp83867_set_tunable(struct phy_device *phydev,
struct ethtool_tunable *tuna, const void *data)
{
switch (tuna->id) {
case ETHTOOL_PHY_DOWNSHIFT:
return dp83867_set_downshift(phydev, *(const u8 *)data);
default:
return -EOPNOTSUPP;
}
}
static int dp83867_config_port_mirroring(struct phy_device *phydev)
{
struct dp83867_private *dp83867 =
......@@ -467,6 +607,12 @@ static int dp83867_config_init(struct phy_device *phydev)
int ret, val, bs;
u16 delay;
/* Force speed optimization for the PHY even if it strapped */
ret = phy_modify(phydev, DP83867_CFG2, DP83867_DOWNSHIFT_EN,
DP83867_DOWNSHIFT_EN);
if (ret)
return ret;
ret = dp83867_verify_rgmii_cfg(phydev);
if (ret)
return ret;
......@@ -655,6 +801,10 @@ static struct phy_driver dp83867_driver[] = {
.config_init = dp83867_config_init,
.soft_reset = dp83867_phy_reset,
.read_status = dp83867_read_status,
.get_tunable = dp83867_get_tunable,
.set_tunable = dp83867_set_tunable,
.get_wol = dp83867_get_wol,
.set_wol = dp83867_set_wol,
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment