Commit cd7201f4 authored by Giuseppe CAVALLARO's avatar Giuseppe CAVALLARO Committed by David S. Miller

stmmac: MDC clock dynamically based on the csr clock input

If a specific clk_csr value is passed from the platform
this means that the CSR Clock Range selection cannot be
changed at run-time and it is fixed (as reported in the driver
documentation). Viceversa the driver will try to set the MDC
clock dynamically according to the actual clock input.
Signed-off-by: default avatarDeepak Sikri <deepak.sikri@st.com>
Signed-off-by: default avatarGiuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: default avatarFrancesco Virlinzi <francesco.virlinzi@st.com>
Reviewed-by: default avatarDavid Laight <david.laight@aculab.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 18f05d64
......@@ -137,7 +137,7 @@ Where:
o pbl: the Programmable Burst Length is maximum number of beats to
be transferred in one DMA transaction.
GMAC also enables the 4xPBL by default.
o clk_csr: CSR Clock range selection.
o clk_csr: fixed CSR Clock range selection.
o has_gmac: uses the GMAC core.
o enh_desc: if sets the MAC will use the enhanced descriptor structure.
o tx_coe: core is able to perform the tx csum in HW.
......
......@@ -97,6 +97,16 @@ struct stmmac_extra_stats {
unsigned long normal_irq_n;
};
/* CSR Frequency Access Defines*/
#define CSR_F_35M 35000000
#define CSR_F_60M 60000000
#define CSR_F_100M 100000000
#define CSR_F_150M 150000000
#define CSR_F_250M 250000000
#define CSR_F_300M 300000000
#define MAC_CSR_H_FRQ_MASK 0x20
#define HASH_TABLE_SIZE 64
#define PAUSE_TIME 0x200
......
......@@ -84,6 +84,7 @@ struct stmmac_priv {
#ifdef CONFIG_HAVE_CLK
struct clk *stmmac_clk;
#endif
int clk_csr;
};
extern int phyaddr;
......
......@@ -163,6 +163,35 @@ static void stmmac_verify_args(void)
pause = PAUSE_TIME;
}
static void stmmac_clk_csr_set(struct stmmac_priv *priv)
{
#ifdef CONFIG_HAVE_CLK
u32 clk_rate;
clk_rate = clk_get_rate(priv->stmmac_clk);
/* Platform provided default clk_csr would be assumed valid
* for all other cases except for the below mentioned ones. */
if (!(priv->clk_csr & MAC_CSR_H_FRQ_MASK)) {
if (clk_rate < CSR_F_35M)
priv->clk_csr = STMMAC_CSR_20_35M;
else if ((clk_rate >= CSR_F_35M) && (clk_rate < CSR_F_60M))
priv->clk_csr = STMMAC_CSR_35_60M;
else if ((clk_rate >= CSR_F_60M) && (clk_rate < CSR_F_100M))
priv->clk_csr = STMMAC_CSR_60_100M;
else if ((clk_rate >= CSR_F_100M) && (clk_rate < CSR_F_150M))
priv->clk_csr = STMMAC_CSR_100_150M;
else if ((clk_rate >= CSR_F_150M) && (clk_rate < CSR_F_250M))
priv->clk_csr = STMMAC_CSR_150_250M;
else if ((clk_rate >= CSR_F_250M) && (clk_rate < CSR_F_300M))
priv->clk_csr = STMMAC_CSR_250_300M;
} /* For values higher than the IEEE 802.3 specified frequency
* we can not estimate the proper divider as it is not known
* the frequency of clk_csr_i. So we do not change the default
* divider. */
#endif
}
#if defined(STMMAC_XMIT_DEBUG) || defined(STMMAC_RX_DEBUG)
static void print_pkt(unsigned char *buf, int len)
{
......@@ -1890,6 +1919,17 @@ struct stmmac_priv *stmmac_dvr_probe(struct device *device,
if (stmmac_clk_get(priv))
goto error;
/* If a specific clk_csr value is passed from the platform
* this means that the CSR Clock Range selection cannot be
* changed at run-time and it is fixed. Viceversa the driver'll try to
* set the MDC clock dynamically according to the csr actual
* clock input.
*/
if (!priv->plat->clk_csr)
stmmac_clk_csr_set(priv);
else
priv->clk_csr = priv->plat->clk_csr;
return priv;
error:
......
......@@ -70,7 +70,7 @@ static int stmmac_mdio_read(struct mii_bus *bus, int phyaddr, int phyreg)
int data;
u16 regValue = (((phyaddr << 11) & (0x0000F800)) |
((phyreg << 6) & (0x000007C0)));
regValue |= MII_BUSY | ((priv->plat->clk_csr & 0xF) << 2);
regValue |= MII_BUSY | ((priv->clk_csr & 0xF) << 2);
if (stmmac_mdio_busy_wait(priv->ioaddr, mii_address))
return -EBUSY;
......@@ -106,7 +106,7 @@ static int stmmac_mdio_write(struct mii_bus *bus, int phyaddr, int phyreg,
(((phyaddr << 11) & (0x0000F800)) | ((phyreg << 6) & (0x000007C0)))
| MII_WRITE;
value |= MII_BUSY | ((priv->plat->clk_csr & 0xF) << 2);
value |= MII_BUSY | ((priv->clk_csr & 0xF) << 2);
/* Wait until any existing MII operation is complete */
if (stmmac_mdio_busy_wait(priv->ioaddr, mii_address))
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment