[media] media: adv7180: define more registers

Replace hard-coded addresses with new register macro defines. No
functional changes.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

drivers/media/i2c/adv7180.c

@@ -56,10 +56,11 @@
 
 #define ADV7182_REG_INPUT_VIDSEL			0x0002
 
+#define ADV7180_REG_OUTPUT_CONTROL			0x0003
 #define ADV7180_REG_EXTENDED_OUTPUT_CONTROL		0x0004
 #define ADV7180_EXTENDED_OUTPUT_CONTROL_NTSCDIS		0xC5
 
-#define ADV7180_REG_AUTODETECT_ENABLE			0x07
+#define ADV7180_REG_AUTODETECT_ENABLE			0x0007
 #define ADV7180_AUTODETECT_DEFAULT			0x7f
 /* Contrast */
 #define ADV7180_REG_CON		0x0008	/*Unsigned */
@@ -100,6 +101,20 @@
 #define ADV7180_REG_IDENT 0x0011
 #define ADV7180_ID_7180 0x18
 
+#define ADV7180_REG_STATUS3		0x0013
+#define ADV7180_REG_ANALOG_CLAMP_CTL	0x0014
+#define ADV7180_REG_SHAP_FILTER_CTL_1	0x0017
+#define ADV7180_REG_CTRL_2		0x001d
+#define ADV7180_REG_VSYNC_FIELD_CTL_1	0x0031
+#define ADV7180_REG_MANUAL_WIN_CTL_1	0x003d
+#define ADV7180_REG_MANUAL_WIN_CTL_2	0x003e
+#define ADV7180_REG_MANUAL_WIN_CTL_3	0x003f
+#define ADV7180_REG_LOCK_CNT		0x0051
+#define ADV7180_REG_CVBS_TRIM		0x0052
+#define ADV7180_REG_CLAMP_ADJ		0x005a
+#define ADV7180_REG_RES_CIR		0x005f
+#define ADV7180_REG_DIFF_MODE		0x0060
+
 #define ADV7180_REG_ICONF1		0x2040
 #define ADV7180_ICONF1_ACTIVE_LOW	0x01
 #define ADV7180_ICONF1_PSYNC_ONLY	0x10
@@ -129,9 +144,15 @@
 #define ADV7180_REG_VPP_SLAVE_ADDR	0xFD
 #define ADV7180_REG_CSI_SLAVE_ADDR	0xFE
 
-#define ADV7180_REG_FLCONTROL 0x40e0
+#define ADV7180_REG_ACE_CTRL1		0x4080
+#define ADV7180_REG_ACE_CTRL5		0x4084
+#define ADV7180_REG_FLCONTROL		0x40e0
 #define ADV7180_FLCONTROL_FL_ENABLE 0x1
 
+#define ADV7180_REG_RST_CLAMP	0x809c
+#define ADV7180_REG_AGC_ADJ1	0x80b6
+#define ADV7180_REG_AGC_ADJ2	0x80c0
+
 #define ADV7180_CSI_REG_PWRDN	0x00
 #define ADV7180_CSI_PWRDN	0x80
 
@@ -886,16 +907,20 @@ static int adv7182_init(struct adv7180_state *state)
 
 	/* ADI required writes */
 	if (state->chip_info->flags & ADV7180_FLAG_MIPI_CSI2) {
-		adv7180_write(state, 0x0003, 0x4e);
-		adv7180_write(state, 0x0004, 0x57);
-		adv7180_write(state, 0x001d, 0xc0);
+		adv7180_write(state, ADV7180_REG_OUTPUT_CONTROL, 0x4e);
+		adv7180_write(state, ADV7180_REG_EXTENDED_OUTPUT_CONTROL, 0x57);
+		adv7180_write(state, ADV7180_REG_CTRL_2, 0xc0);
 	} else {
 		if (state->chip_info->flags & ADV7180_FLAG_V2)
-			adv7180_write(state, 0x0004, 0x17);
+			adv7180_write(state,
+				      ADV7180_REG_EXTENDED_OUTPUT_CONTROL,
+				      0x17);
 		else
-			adv7180_write(state, 0x0004, 0x07);
-		adv7180_write(state, 0x0003, 0x0c);
-		adv7180_write(state, 0x001d, 0x40);
+			adv7180_write(state,
+				      ADV7180_REG_EXTENDED_OUTPUT_CONTROL,
+				      0x07);
+		adv7180_write(state, ADV7180_REG_OUTPUT_CONTROL, 0x0c);
+		adv7180_write(state, ADV7180_REG_CTRL_2, 0x40);
 	}
 
 	adv7180_write(state, 0x0013, 0x00);
@@ -972,8 +997,8 @@ static int adv7182_select_input(struct adv7180_state *state, unsigned int input)
 		return ret;
 
 	/* Reset clamp circuitry - ADI recommended writes */
-	adv7180_write(state, 0x809c, 0x00);
-	adv7180_write(state, 0x809c, 0xff);
+	adv7180_write(state, ADV7180_REG_RST_CLAMP, 0x00);
+	adv7180_write(state, ADV7180_REG_RST_CLAMP, 0xff);
 
 	input_type = adv7182_get_input_type(input);
 
@@ -981,10 +1006,10 @@ static int adv7182_select_input(struct adv7180_state *state, unsigned int input)
 	case ADV7182_INPUT_TYPE_CVBS:
 	case ADV7182_INPUT_TYPE_DIFF_CVBS:
 		/* ADI recommends to use the SH1 filter */
-		adv7180_write(state, 0x0017, 0x41);
+		adv7180_write(state, ADV7180_REG_SHAP_FILTER_CTL_1, 0x41);
 		break;
 	default:
-		adv7180_write(state, 0x0017, 0x01);
+		adv7180_write(state, ADV7180_REG_SHAP_FILTER_CTL_1, 0x01);
 		break;
 	}
 
@@ -994,21 +1019,21 @@ static int adv7182_select_input(struct adv7180_state *state, unsigned int input)
 		lbias = adv7182_lbias_settings[input_type];
 
 	for (i = 0; i < ARRAY_SIZE(adv7182_lbias_settings[0]); i++)
-		adv7180_write(state, 0x0052 + i, lbias[i]);
+		adv7180_write(state, ADV7180_REG_CVBS_TRIM + i, lbias[i]);
 
 	if (input_type == ADV7182_INPUT_TYPE_DIFF_CVBS) {
 		/* ADI required writes to make differential CVBS work */
-		adv7180_write(state, 0x005f, 0xa8);
-		adv7180_write(state, 0x005a, 0x90);
-		adv7180_write(state, 0x0060, 0xb0);
-		adv7180_write(state, 0x80b6, 0x08);
-		adv7180_write(state, 0x80c0, 0xa0);
+		adv7180_write(state, ADV7180_REG_RES_CIR, 0xa8);
+		adv7180_write(state, ADV7180_REG_CLAMP_ADJ, 0x90);
+		adv7180_write(state, ADV7180_REG_DIFF_MODE, 0xb0);
+		adv7180_write(state, ADV7180_REG_AGC_ADJ1, 0x08);
+		adv7180_write(state, ADV7180_REG_AGC_ADJ2, 0xa0);
 	} else {
-		adv7180_write(state, 0x005f, 0xf0);
-		adv7180_write(state, 0x005a, 0xd0);
-		adv7180_write(state, 0x0060, 0x10);
-		adv7180_write(state, 0x80b6, 0x9c);
-		adv7180_write(state, 0x80c0, 0x00);
+		adv7180_write(state, ADV7180_REG_RES_CIR, 0xf0);
+		adv7180_write(state, ADV7180_REG_CLAMP_ADJ, 0xd0);
+		adv7180_write(state, ADV7180_REG_DIFF_MODE, 0x10);
+		adv7180_write(state, ADV7180_REG_AGC_ADJ1, 0x9c);
+		adv7180_write(state, ADV7180_REG_AGC_ADJ2, 0x00);
 	}
 
 	return 0;