Revert "xhci: Clear the host side toggle manually when endpoint is 'soft reset'"

This reverts commit 27082e26 ("xhci: Clear the host side toggle manually")

Turns out this fix to enable soft resetting endpoints wasn't mature enough.
It caused regression with some usb DVB-T devices and needs some more tuning
to get the endpiont ring pointers set correctly.

The original commit was tagged for stable 3.18, and should be reverted
from there as well.

Cc: stable <stable@vger.kernel.org> # v3.18
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/usb/host/xhci-ring.c

@@ -1729,7 +1729,7 @@ static void xhci_cleanup_halted_endpoint(struct xhci_hcd *xhci,
 	if (!command)
 		return;
 
-	ep->ep_state |= EP_HALTED | EP_RECENTLY_HALTED;
+	ep->ep_state |= EP_HALTED;
 	ep->stopped_stream = stream_id;
 
 	xhci_queue_reset_ep(xhci, command, slot_id, ep_index);

drivers/usb/host/xhci.c

@@ -1338,12 +1338,6 @@ int xhci_urb_enqueue(struct usb_hcd *hcd, struct urb *urb, gfp_t mem_flags)
 		goto exit;
 	}
 
-	/* Reject urb if endpoint is in soft reset, queue must stay empty */
-	if (xhci->devs[slot_id]->eps[ep_index].ep_state & EP_CONFIG_PENDING) {
-		xhci_warn(xhci, "Can't enqueue URB while ep is in soft reset\n");
-		ret = -EINVAL;
-	}
-
 	if (usb_endpoint_xfer_isoc(&urb->ep->desc))
 		size = urb->number_of_packets;
 	else
@@ -2954,36 +2948,23 @@ void xhci_cleanup_stalled_ring(struct xhci_hcd *xhci,
 	}
 }
 
-/* Called after clearing a halted device. USB core should have sent the control
+/* Called when clearing halted device. The core should have sent the control
  * message to clear the device halt condition. The host side of the halt should
- * already be cleared with a reset endpoint command issued immediately when the
- * STALL tx event was received.
+ * already be cleared with a reset endpoint command issued when the STALL tx
+ * event was received.
+ *
+ * Context: in_interrupt
  */
 
 void xhci_endpoint_reset(struct usb_hcd *hcd,
 		struct usb_host_endpoint *ep)
 {
 	struct xhci_hcd *xhci;
-	struct usb_device *udev;
-	struct xhci_virt_device *virt_dev;
-	struct xhci_virt_ep *virt_ep;
-	struct xhci_input_control_ctx *ctrl_ctx;
-	struct xhci_command *command;
-	unsigned int ep_index, ep_state;
-	unsigned long flags;
-	u32 ep_flag;
 
 	xhci = hcd_to_xhci(hcd);
-	udev = (struct usb_device *) ep->hcpriv;
-	if (!ep->hcpriv)
-		return;
-	virt_dev = xhci->devs[udev->slot_id];
-	ep_index = xhci_get_endpoint_index(&ep->desc);
-	virt_ep = &virt_dev->eps[ep_index];
-	ep_state = virt_ep->ep_state;
 
 	/*
-	 * Implement the config ep command in xhci 4.6.8 additional note:
+	 * We might need to implement the config ep cmd in xhci 4.8.1 note:
 	 * The Reset Endpoint Command may only be issued to endpoints in the
 	 * Halted state. If software wishes reset the Data Toggle or Sequence
 	 * Number of an endpoint that isn't in the Halted state, then software
@@ -2991,72 +2972,9 @@ void xhci_endpoint_reset(struct usb_hcd *hcd,
 	 * for the target endpoint. that is in the Stopped state.
 	 */
 
-	if (ep_state & SET_DEQ_PENDING || ep_state & EP_RECENTLY_HALTED) {
-		virt_ep->ep_state &= ~EP_RECENTLY_HALTED;
-		xhci_dbg(xhci, "ep recently halted, no toggle reset needed\n");
-		return;
-	}
-
-	/* Only interrupt and bulk ep's use Data toggle, USB2 spec 5.5.4-> */
-	if (usb_endpoint_xfer_control(&ep->desc) ||
-	    usb_endpoint_xfer_isoc(&ep->desc))
-		return;
-
-	ep_flag = xhci_get_endpoint_flag(&ep->desc);
-
-	if (ep_flag == SLOT_FLAG || ep_flag == EP0_FLAG)
-		return;
-
-	command = xhci_alloc_command(xhci, true, true, GFP_NOWAIT);
-	if (!command) {
-		xhci_err(xhci, "Could not allocate xHCI command structure.\n");
-		return;
-	}
-
-	spin_lock_irqsave(&xhci->lock, flags);
-
-	/* block ringing ep doorbell */
-	virt_ep->ep_state |= EP_CONFIG_PENDING;
-
-	/*
-	 * Make sure endpoint ring is empty before resetting the toggle/seq.
-	 * Driver is required to synchronously cancel all transfer request.
-	 *
-	 * xhci 4.6.6 says we can issue a configure endpoint command on a
-	 * running endpoint ring as long as it's idle (queue empty)
-	 */
-
-	if (!list_empty(&virt_ep->ring->td_list)) {
-		dev_err(&udev->dev, "EP not empty, refuse reset\n");
-		spin_unlock_irqrestore(&xhci->lock, flags);
-		goto cleanup;
-	}
-
-	xhci_dbg(xhci, "Reset toggle/seq for slot %d, ep_index: %d\n",
-		 udev->slot_id, ep_index);
-
-	ctrl_ctx = xhci_get_input_control_ctx(command->in_ctx);
-	if (!ctrl_ctx) {
-		xhci_err(xhci, "Could not get input context, bad type. virt_dev: %p, in_ctx %p\n",
-			 virt_dev, virt_dev->in_ctx);
-		spin_unlock_irqrestore(&xhci->lock, flags);
-		goto cleanup;
-	}
-	xhci_setup_input_ctx_for_config_ep(xhci, command->in_ctx,
-					   virt_dev->out_ctx, ctrl_ctx,
-					   ep_flag, ep_flag);
-	xhci_endpoint_copy(xhci, command->in_ctx, virt_dev->out_ctx, ep_index);
-
-	xhci_queue_configure_endpoint(xhci, command, command->in_ctx->dma,
-				     udev->slot_id, false);
-	xhci_ring_cmd_db(xhci);
-	spin_unlock_irqrestore(&xhci->lock, flags);
-
-	wait_for_completion(command->completion);
-
-cleanup:
-	virt_ep->ep_state &= ~EP_CONFIG_PENDING;
-	xhci_free_command(xhci, command);
+	/* For now just print debug to follow the situation */
+	xhci_dbg(xhci, "Endpoint 0x%x ep reset callback called\n",
+		 ep->desc.bEndpointAddress);
 }
 
 static int xhci_check_streams_endpoint(struct xhci_hcd *xhci,

drivers/usb/host/xhci.h

@@ -865,8 +865,6 @@ struct xhci_virt_ep {
 #define EP_HAS_STREAMS		(1 << 4)
 /* Transitioning the endpoint to not using streams, don't enqueue URBs */
 #define EP_GETTING_NO_STREAMS	(1 << 5)
-#define EP_RECENTLY_HALTED	(1 << 6)
-#define EP_CONFIG_PENDING	(1 << 7)
 	/* ----  Related to URB cancellation ---- */
 	struct list_head	cancelled_td_list;
 	struct xhci_td		*stopped_td;