Merge branch 'remotes/lorenzo/pci/aardvark'

- Fix s390 build error (Pali Rohár)

- Check for errors from pci_bridge_emul_init() (Pali Rohár)

- Export pci-bridge-emul functions for use by modules (Pali Rohár)

- Make aardvark driver modular (Pali Rohár)

- Move PCIe reset code to advk_pcie_train_link() (Pali Rohár)

- Convert internal SMCC firmware return codes to errno (Pali Rohár)

- Fix initialization with old Marvell's Arm Trusted Firmware (Pali Rohár)

* remotes/lorenzo/pci/aardvark:
  PCI: aardvark: Fix initialization with old Marvell's Arm Trusted Firmware
  phy: marvell: comphy: Convert internal SMCC firmware return codes to errno
  PCI: aardvark: Move PCIe reset card code to advk_pcie_train_link()
  PCI: aardvark: Implement driver 'remove' function and allow to build it as module
  PCI: pci-bridge-emul: Export API functions
  PCI: aardvark: Check for errors from pci_bridge_emul_init() call
  PCI: aardvark: Fix compilation on s390

drivers/pci/controller/Kconfig

@@ -12,7 +12,7 @@ config PCI_MVEBU
 	select PCI_BRIDGE_EMUL
 
 config PCI_AARDVARK
-	bool "Aardvark PCIe controller"
+	tristate "Aardvark PCIe controller"
 	depends on (ARCH_MVEBU && ARM64) || COMPILE_TEST
 	depends on OF
 	depends on PCI_MSI_IRQ_DOMAIN

drivers/pci/controller/pci-aardvark.c

@@ -9,11 +9,12 @@
  */
 
 #include <linux/delay.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>
 #include <linux/irqdomain.h>
 #include <linux/kernel.h>
+#include <linux/module.h>
 #include <linux/pci.h>
 #include <linux/init.h>
 #include <linux/phy/phy.h>
@@ -251,6 +252,25 @@ static void advk_pcie_wait_for_retrain(struct advk_pcie *pcie)
 	}
 }
 
+static void advk_pcie_issue_perst(struct advk_pcie *pcie)
+{
+	u32 reg;
+
+	if (!pcie->reset_gpio)
+		return;
+
+	/* PERST does not work for some cards when link training is enabled */
+	reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
+	reg &= ~LINK_TRAINING_EN;
+	advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG);
+
+	/* 10ms delay is needed for some cards */
+	dev_info(&pcie->pdev->dev, "issuing PERST via reset GPIO for 10ms\n");
+	gpiod_set_value_cansleep(pcie->reset_gpio, 1);
+	usleep_range(10000, 11000);
+	gpiod_set_value_cansleep(pcie->reset_gpio, 0);
+}
+
 static int advk_pcie_train_at_gen(struct advk_pcie *pcie, int gen)
 {
 	int ret, neg_gen;
@@ -298,6 +318,21 @@ static void advk_pcie_train_link(struct advk_pcie *pcie)
 	struct device *dev = &pcie->pdev->dev;
 	int neg_gen = -1, gen;
 
+	/*
+	 * Reset PCIe card via PERST# signal. Some cards are not detected
+	 * during link training when they are in some non-initial state.
+	 */
+	advk_pcie_issue_perst(pcie);
+
+	/*
+	 * PERST# signal could have been asserted by pinctrl subsystem before
+	 * probe() callback has been called or issued explicitly by reset gpio
+	 * function advk_pcie_issue_perst(), making the endpoint going into
+	 * fundamental reset. As required by PCI Express spec a delay for at
+	 * least 100ms after such a reset before link training is needed.
+	 */
+	msleep(PCI_PM_D3COLD_WAIT);
+
 	/*
 	 * Try link training at link gen specified by device tree property
 	 * 'max-link-speed'. If this fails, iteratively train at lower gen.
@@ -330,31 +365,10 @@ static void advk_pcie_train_link(struct advk_pcie *pcie)
 	dev_err(dev, "link never came up\n");
 }
 
-static void advk_pcie_issue_perst(struct advk_pcie *pcie)
-{
-	u32 reg;
-
-	if (!pcie->reset_gpio)
-		return;
-
-	/* PERST does not work for some cards when link training is enabled */
-	reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
-	reg &= ~LINK_TRAINING_EN;
-	advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG);
-
-	/* 10ms delay is needed for some cards */
-	dev_info(&pcie->pdev->dev, "issuing PERST via reset GPIO for 10ms\n");
-	gpiod_set_value_cansleep(pcie->reset_gpio, 1);
-	usleep_range(10000, 11000);
-	gpiod_set_value_cansleep(pcie->reset_gpio, 0);
-}
-
 static void advk_pcie_setup_hw(struct advk_pcie *pcie)
 {
 	u32 reg;
 
-	advk_pcie_issue_perst(pcie);
-
 	/* Enable TX */
 	reg = advk_readl(pcie, PCIE_CORE_REF_CLK_REG);
 	reg |= PCIE_CORE_REF_CLK_TX_ENABLE;
@@ -431,15 +445,6 @@ static void advk_pcie_setup_hw(struct advk_pcie *pcie)
 	reg |= PIO_CTRL_ADDR_WIN_DISABLE;
 	advk_writel(pcie, reg, PIO_CTRL);
 
-	/*
-	 * PERST# signal could have been asserted by pinctrl subsystem before
-	 * probe() callback has been called or issued explicitly by reset gpio
-	 * function advk_pcie_issue_perst(), making the endpoint going into
-	 * fundamental reset. As required by PCI Express spec a delay for at
-	 * least 100ms after such a reset before link training is needed.
-	 */
-	msleep(PCI_PM_D3COLD_WAIT);
-
 	advk_pcie_train_link(pcie);
 
 	/*
@@ -607,7 +612,7 @@ static struct pci_bridge_emul_ops advk_pci_bridge_emul_ops = {
  * Initialize the configuration space of the PCI-to-PCI bridge
  * associated with the given PCIe interface.
  */
-static void advk_sw_pci_bridge_init(struct advk_pcie *pcie)
+static int advk_sw_pci_bridge_init(struct advk_pcie *pcie)
 {
 	struct pci_bridge_emul *bridge = &pcie->bridge;
 
@@ -633,8 +638,7 @@ static void advk_sw_pci_bridge_init(struct advk_pcie *pcie)
 	bridge->data = pcie;
 	bridge->ops = &advk_pci_bridge_emul_ops;
 
-	pci_bridge_emul_init(bridge, 0);
-
+	return pci_bridge_emul_init(bridge, 0);
 }
 
 static bool advk_pcie_valid_device(struct advk_pcie *pcie, struct pci_bus *bus,
@@ -1077,7 +1081,9 @@ static int advk_pcie_enable_phy(struct advk_pcie *pcie)
 	}
 
 	ret = phy_power_on(pcie->phy);
-	if (ret) {
+	if (ret == -EOPNOTSUPP) {
+		dev_warn(&pcie->pdev->dev, "PHY unsupported by firmware\n");
+	} else if (ret) {
 		phy_exit(pcie->phy);
 		return ret;
 	}
@@ -1122,6 +1128,7 @@ static int advk_pcie_probe(struct platform_device *pdev)
 
 	pcie = pci_host_bridge_priv(bridge);
 	pcie->pdev = pdev;
+	platform_set_drvdata(pdev, pcie);
 
 	pcie->base = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(pcie->base))
@@ -1167,7 +1174,11 @@ static int advk_pcie_probe(struct platform_device *pdev)
 
 	advk_pcie_setup_hw(pcie);
 
-	advk_sw_pci_bridge_init(pcie);
+	ret = advk_sw_pci_bridge_init(pcie);
+	if (ret) {
+		dev_err(dev, "Failed to register emulated root PCI bridge\n");
+		return ret;
+	}
 
 	ret = advk_pcie_init_irq_domain(pcie);
 	if (ret) {
@@ -1195,18 +1206,37 @@ static int advk_pcie_probe(struct platform_device *pdev)
 	return 0;
 }
 
+static int advk_pcie_remove(struct platform_device *pdev)
+{
+	struct advk_pcie *pcie = platform_get_drvdata(pdev);
+	struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie);
+
+	pci_lock_rescan_remove();
+	pci_stop_root_bus(bridge->bus);
+	pci_remove_root_bus(bridge->bus);
+	pci_unlock_rescan_remove();
+
+	advk_pcie_remove_msi_irq_domain(pcie);
+	advk_pcie_remove_irq_domain(pcie);
+
+	return 0;
+}
+
 static const struct of_device_id advk_pcie_of_match_table[] = {
 	{ .compatible = "marvell,armada-3700-pcie", },
 	{},
 };
+MODULE_DEVICE_TABLE(of, advk_pcie_of_match_table);
 
 static struct platform_driver advk_pcie_driver = {
 	.driver = {
 		.name = "advk-pcie",
 		.of_match_table = advk_pcie_of_match_table,
-		/* Driver unloading/unbinding currently not supported */
-		.suppress_bind_attrs = true,
 	},
 	.probe = advk_pcie_probe,
+	.remove = advk_pcie_remove,
 };
-builtin_platform_driver(advk_pcie_driver);
+module_platform_driver(advk_pcie_driver);
+
+MODULE_DESCRIPTION("Aardvark PCIe controller");
+MODULE_LICENSE("GPL v2");

drivers/pci/pci-bridge-emul.c

@@ -294,6 +294,7 @@ int pci_bridge_emul_init(struct pci_bridge_emul *bridge,
 
 	return 0;
 }
+EXPORT_SYMBOL_GPL(pci_bridge_emul_init);
 
 /*
  * Cleanup a pci_bridge_emul structure that was previously initialized
@@ -305,6 +306,7 @@ void pci_bridge_emul_cleanup(struct pci_bridge_emul *bridge)
 		kfree(bridge->pcie_cap_regs_behavior);
 	kfree(bridge->pci_regs_behavior);
 }
+EXPORT_SYMBOL_GPL(pci_bridge_emul_cleanup);
 
 /*
  * Should be called by the PCI controller driver when reading the PCI
@@ -366,6 +368,7 @@ int pci_bridge_emul_conf_read(struct pci_bridge_emul *bridge, int where,
 
 	return PCIBIOS_SUCCESSFUL;
 }
+EXPORT_SYMBOL_GPL(pci_bridge_emul_conf_read);
 
 /*
  * Should be called by the PCI controller driver when writing the PCI
@@ -430,3 +433,4 @@ int pci_bridge_emul_conf_write(struct pci_bridge_emul *bridge, int where,
 
 	return PCIBIOS_SUCCESSFUL;
 }
+EXPORT_SYMBOL_GPL(pci_bridge_emul_conf_write);

drivers/phy/marvell/phy-mvebu-a3700-comphy.c

@@ -26,7 +26,6 @@
 #define COMPHY_SIP_POWER_ON			0x82000001
 #define COMPHY_SIP_POWER_OFF			0x82000002
 #define COMPHY_SIP_PLL_LOCK			0x82000003
-#define COMPHY_FW_NOT_SUPPORTED			(-1)
 
 #define COMPHY_FW_MODE_SATA			0x1
 #define COMPHY_FW_MODE_SGMII			0x2
@@ -112,10 +111,19 @@ static int mvebu_a3700_comphy_smc(unsigned long function, unsigned long lane,
 				  unsigned long mode)
 {
 	struct arm_smccc_res res;
+	s32 ret;
 
 	arm_smccc_smc(function, lane, mode, 0, 0, 0, 0, 0, &res);
+	ret = res.a0;
 
-	return res.a0;
+	switch (ret) {
+	case SMCCC_RET_SUCCESS:
+		return 0;
+	case SMCCC_RET_NOT_SUPPORTED:
+		return -EOPNOTSUPP;
+	default:
+		return -EINVAL;
+	}
 }
 
 static int mvebu_a3700_comphy_get_fw_mode(int lane, int port,
@@ -220,7 +228,7 @@ static int mvebu_a3700_comphy_power_on(struct phy *phy)
 	}
 
 	ret = mvebu_a3700_comphy_smc(COMPHY_SIP_POWER_ON, lane->id, fw_param);
-	if (ret == COMPHY_FW_NOT_SUPPORTED)
+	if (ret == -EOPNOTSUPP)
 		dev_err(lane->dev,
 			"unsupported SMC call, try updating your firmware\n");
 

drivers/phy/marvell/phy-mvebu-cp110-comphy.c

@@ -123,7 +123,6 @@
 
 #define COMPHY_SIP_POWER_ON	0x82000001
 #define COMPHY_SIP_POWER_OFF	0x82000002
-#define COMPHY_FW_NOT_SUPPORTED	(-1)
 
 /*
  * A lane is described by the following bitfields:
@@ -273,10 +272,19 @@ static int mvebu_comphy_smc(unsigned long function, unsigned long phys,
 			    unsigned long lane, unsigned long mode)
 {
 	struct arm_smccc_res res;
+	s32 ret;
 
 	arm_smccc_smc(function, phys, lane, mode, 0, 0, 0, 0, &res);
+	ret = res.a0;
 
-	return res.a0;
+	switch (ret) {
+	case SMCCC_RET_SUCCESS:
+		return 0;
+	case SMCCC_RET_NOT_SUPPORTED:
+		return -EOPNOTSUPP;
+	default:
+		return -EINVAL;
+	}
 }
 
 static int mvebu_comphy_get_mode(bool fw_mode, int lane, int port,
@@ -819,7 +827,7 @@ static int mvebu_comphy_power_on(struct phy *phy)
 	if (!ret)
 		return ret;
 
-	if (ret == COMPHY_FW_NOT_SUPPORTED)
+	if (ret == -EOPNOTSUPP)
 		dev_err(priv->dev,
 			"unsupported SMC call, try updating your firmware\n");