Merge branch 'at91/cleanup' into next/dt

Conflicts:
	arch/arm/boot/dts/at91sam9rl.dtsi

Needed as a dependency for the at91/dt2 branch
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/clock/at91-clock.txt

@@ -6,6 +6,16 @@ This binding uses the common clock binding[1].
 
 Required properties:
 - compatible : shall be one of the following:
+	"atmel,at91sam9x5-sckc":
+		at91 SCKC (Slow Clock Controller)
+		This node contains the slow clock definitions.
+
+	"atmel,at91sam9x5-clk-slow-osc":
+		at91 slow oscillator
+
+	"atmel,at91sam9x5-clk-slow-rc-osc":
+		at91 internal slow RC oscillator
+
 	"atmel,at91rm9200-pmc" or
 	"atmel,at91sam9g45-pmc" or
 	"atmel,at91sam9n12-pmc" or
@@ -15,8 +25,18 @@ Required properties:
 		All at91 specific clocks (clocks defined below) must be child
 		node of the PMC node.
 
+	"atmel,at91sam9x5-clk-slow" (under sckc node)
+	or
+	"atmel,at91sam9260-clk-slow" (under pmc node):
+		at91 slow clk
+
+	"atmel,at91rm9200-clk-main-osc"
+	"atmel,at91sam9x5-clk-main-rc-osc"
+		at91 main clk sources
+
+	"atmel,at91sam9x5-clk-main"
 	"atmel,at91rm9200-clk-main":
-		at91 main oscillator
+		at91 main clock
 
 	"atmel,at91rm9200-clk-master" or
 	"atmel,at91sam9x5-clk-master":
@@ -54,6 +74,63 @@ Required properties:
 	"atmel,at91sam9x5-clk-utmi":
 		at91 utmi clock
 
+Required properties for SCKC node:
+- reg : defines the IO memory reserved for the SCKC.
+- #size-cells : shall be 0 (reg is used to encode clk id).
+- #address-cells : shall be 1 (reg is used to encode clk id).
+
+
+For example:
+	sckc: sckc@fffffe50 {
+		compatible = "atmel,sama5d3-pmc";
+		reg = <0xfffffe50 0x4>
+		#size-cells = <0>;
+		#address-cells = <1>;
+
+		/* put at91 slow clocks here */
+	};
+
+
+Required properties for internal slow RC oscillator:
+- #clock-cells : from common clock binding; shall be set to 0.
+- clock-frequency : define the internal RC oscillator frequency.
+
+Optional properties:
+- clock-accuracy : define the internal RC oscillator accuracy.
+
+For example:
+	slow_rc_osc: slow_rc_osc {
+		compatible = "atmel,at91sam9x5-clk-slow-rc-osc";
+		clock-frequency = <32768>;
+		clock-accuracy = <50000000>;
+	};
+
+Required properties for slow oscillator:
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall encode the main osc source clk sources (see atmel datasheet).
+
+Optional properties:
+- atmel,osc-bypass : boolean property. Set this when a clock signal is directly
+  provided on XIN.
+
+For example:
+	slow_osc: slow_osc {
+		compatible = "atmel,at91rm9200-clk-slow-osc";
+		#clock-cells = <0>;
+		clocks = <&slow_xtal>;
+	};
+
+Required properties for slow clock:
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall encode the slow clk sources (see atmel datasheet).
+
+For example:
+	clk32k: slck {
+		compatible = "atmel,at91sam9x5-clk-slow";
+		#clock-cells = <0>;
+		clocks = <&slow_rc_osc &slow_osc>;
+	};
+
 Required properties for PMC node:
 - reg : defines the IO memory reserved for the PMC.
 - #size-cells : shall be 0 (reg is used to encode clk id).
@@ -85,24 +162,57 @@ For example:
 		/* put at91 clocks here */
 	};
 
+Required properties for main clock internal RC oscillator:
+- interrupt-parent : must reference the PMC node.
+- interrupts : shall be set to "<0>".
+- clock-frequency : define the internal RC oscillator frequency.
+
+Optional properties:
+- clock-accuracy : define the internal RC oscillator accuracy.
+
+For example:
+	main_rc_osc: main_rc_osc {
+		compatible = "atmel,at91sam9x5-clk-main-rc-osc";
+		interrupt-parent = <&pmc>;
+		interrupts = <0>;
+		clock-frequency = <12000000>;
+		clock-accuracy = <50000000>;
+	};
+
+Required properties for main clock oscillator:
+- interrupt-parent : must reference the PMC node.
+- interrupts : shall be set to "<0>".
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall encode the main osc source clk sources (see atmel datasheet).
+
+Optional properties:
+- atmel,osc-bypass : boolean property. Specified if a clock signal is provided
+  on XIN.
+
+  clock signal is directly provided on XIN pin.
+
+For example:
+	main_osc: main_osc {
+		compatible = "atmel,at91rm9200-clk-main-osc";
+		interrupt-parent = <&pmc>;
+		interrupts = <0>;
+		#clock-cells = <0>;
+		clocks = <&main_xtal>;
+	};
+
 Required properties for main clock:
 - interrupt-parent : must reference the PMC node.
 - interrupts : shall be set to "<0>".
 - #clock-cells : from common clock binding; shall be set to 0.
-- clocks (optional if clock-frequency is provided) : shall be the slow clock
-	phandle. This clock is used to calculate the main clock rate if
-	"clock-frequency" is not provided.
-- clock-frequency : the main oscillator frequency.Prefer the use of
-	"clock-frequency" over automatic clock rate calculation.
+- clocks : shall encode the main clk sources (see atmel datasheet).
 
 For example:
 	main: mainck {
-		compatible = "atmel,at91rm9200-clk-main";
+		compatible = "atmel,at91sam9x5-clk-main";
 		interrupt-parent = <&pmc>;
 		interrupts = <0>;
 		#clock-cells = <0>;
-		clocks = <&ck32k>;
-		clock-frequency = <18432000>;
+		clocks = <&main_rc_osc &main_osc>;
 	};
 
 Required properties for master clock:

MAINTAINERS

@@ -1617,12 +1617,6 @@ S:	Supported
 F:	drivers/misc/atmel_tclib.c
 F:	drivers/clocksource/tcb_clksrc.c
 
-ATMEL TSADCC DRIVER
-M:	Josh Wu <josh.wu@atmel.com>
-L:	linux-input@vger.kernel.org
-S:	Supported
-F:	drivers/input/touchscreen/atmel_tsadcc.c
-
 ATMEL USBA UDC DRIVER
 M:	Nicolas Ferre <nicolas.ferre@atmel.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)

arch/arm/Kconfig

@@ -376,7 +376,6 @@ config ARCH_AT91
 	select ARCH_REQUIRE_GPIOLIB
 	select CLKDEV_LOOKUP
 	select IRQ_DOMAIN
-	select NEED_MACH_GPIO_H
 	select NEED_MACH_IO_H if PCCARD
 	select PINCTRL
 	select PINCTRL_AT91 if USE_OF

arch/arm/boot/dts/at91-cosino_mega2560.dts

@@ -32,11 +32,6 @@ adc0: adc@f804c000 {
 				status = "okay";
 			};
 
-
-			tsadcc: tsadcc@f804c000 {
-				status = "okay";
-			};
-
 			rtc@fffffeb0 {
 				status = "okay";
 			};

arch/arm/boot/dts/at91-sama5d3_xplained.dts

@@ -21,6 +21,14 @@ memory {
 		reg = <0x20000000 0x10000000>;
 	};
 
+	slow_xtal {
+		clock-frequency = <32768>;
+	};
+
+	main_xtal {
+		clock-frequency = <12000000>;
+	};
+
 	ahb {
 		apb {
 			mmc0: mmc@f0000000 {

arch/arm/boot/dts/at91sam9261.dtsi

@@ -46,6 +46,18 @@ memory {
 		reg = <0x20000000 0x08000000>;
 	};
 
+	main_xtal: main_xtal {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	slow_xtal: slow_xtal {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
 	ahb {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -556,17 +568,24 @@ pmc: pmc@fffffc00 {
 				#size-cells = <0>;
 				#interrupt-cells = <1>;
 
-				clk32k: slck {
+				slow_rc_osc: slow_rc_osc {
 					compatible = "fixed-clock";
 					#clock-cells = <0>;
 					clock-frequency = <32768>;
+					clock-accuracy = <50000000>;
+				};
+
+				clk32k: slck {
+					compatible = "atmel,at91sam9260-clk-slow";
+					#clock-cells = <0>;
+					clocks = <&slow_rc_osc &slow_xtal>;
 				};
 
 				main: mainck {
 					compatible = "atmel,at91rm9200-clk-main";
 					#clock-cells = <0>;
 					interrupts-extended = <&pmc AT91_PMC_MOSCS>;
-					clocks = <&clk32k>;
+					clocks = <&main_xtal>;
 				};
 
 				plla: pllack {

arch/arm/boot/dts/at91sam9261ek.dts

@@ -20,6 +20,10 @@ memory {
 		reg = <0x20000000 0x4000000>;
 	};
 
+	main_xtal {
+		clock-frequency = <18432000>;
+	};
+
 	clocks {
 		#address-cells = <1>;
 		#size-cells = <1>;

arch/arm/boot/dts/at91sam9rl.dtsi

@@ -50,6 +50,18 @@ memory {
 		reg = <0x20000000 0x04000000>;
 	};
 
+	slow_xtal: slow_xtal {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	main_xtal: main_xtal {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
 	clocks {
 		adc_op_clk: adc_op_clk{
 			compatible = "fixed-clock";
@@ -795,17 +807,11 @@ pmc: pmc@fffffc00 {
 				#size-cells = <0>;
 				#interrupt-cells = <1>;
 
-				clk32k: slck {
-					compatible = "fixed-clock";
-					#clock-cells = <0>;
-					clock-frequency = <32768>;
-				};
-
 				main: mainck {
 					compatible = "atmel,at91rm9200-clk-main";
 					#clock-cells = <0>;
 					interrupts-extended = <&pmc AT91_PMC_MOSCS>;
-					clocks = <&clk32k>;
+					clocks = <&main_xtal>;
 				};
 
 				plla: pllack {
@@ -1017,6 +1023,32 @@ watchdog@fffffd40 {
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				status = "disabled";
 			};
+
+			sckc@fffffd50 {
+				compatible = "atmel,at91sam9x5-sckc";
+				reg = <0xfffffd50 0x4>;
+
+				slow_osc: slow_osc {
+					compatible = "atmel,at91sam9x5-clk-slow-osc";
+					#clock-cells = <0>;
+					atmel,startup-time-usec = <1200000>;
+					clocks = <&slow_xtal>;
+				};
+
+				slow_rc_osc: slow_rc_osc {
+					compatible = "atmel,at91sam9x5-clk-slow-rc-osc";
+					#clock-cells = <0>;
+					atmel,startup-time-usec = <75>;
+					clock-frequency = <32768>;
+					clock-accuracy = <50000000>;
+				};
+
+				clk32k: slck {
+					compatible = "atmel,at91sam9x5-clk-slow";
+					#clock-cells = <0>;
+					clocks = <&slow_rc_osc &slow_osc>;
+				};
+			};
 		};
 	};
 

arch/arm/boot/dts/at91sam9rlek.dts

@@ -20,6 +20,15 @@ memory {
 		reg = <0x20000000 0x4000000>;
 	};
 
+
+	slow_xtal {
+		clock-frequency = <32768>;
+	};
+
+	main_xtal {
+		clock-frequency = <12000000>;
+	};
+
 	clocks {
 		#address-cells = <1>;
 		#size-cells = <1>;

arch/arm/boot/dts/sama5d3.dtsi

@@ -58,6 +58,18 @@ memory {
 		reg = <0x20000000 0x8000000>;
 	};
 
+	slow_xtal: slow_xtal {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	main_xtal: main_xtal {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
 	clocks {
 		adc_op_clk: adc_op_clk{
 			compatible = "fixed-clock";
@@ -833,18 +845,29 @@ pmc: pmc@fffffc00 {
 				#size-cells = <0>;
 				#interrupt-cells = <1>;
 
-				clk32k: slck {
-					compatible = "fixed-clock";
+				main_rc_osc: main_rc_osc {
+					compatible = "atmel,at91sam9x5-clk-main-rc-osc";
 					#clock-cells = <0>;
-					clock-frequency = <32768>;
+					interrupt-parent = <&pmc>;
+					interrupts = <AT91_PMC_MOSCRCS>;
+					clock-frequency = <12000000>;
+					clock-accuracy = <50000000>;
 				};
 
-				main: mainck {
-					compatible = "atmel,at91rm9200-clk-main";
+				main_osc: main_osc {
+					compatible = "atmel,at91rm9200-clk-main-osc";
 					#clock-cells = <0>;
 					interrupt-parent = <&pmc>;
 					interrupts = <AT91_PMC_MOSCS>;
-					clocks = <&clk32k>;
+					clocks = <&main_xtal>;
+				};
+
+				main: mainck {
+					compatible = "atmel,at91sam9x5-clk-main";
+					#clock-cells = <0>;
+					interrupt-parent = <&pmc>;
+					interrupts = <AT91_PMC_MOSCSELS>;
+					clocks = <&main_rc_osc &main_osc>;
 				};
 
 				plla: pllack {
@@ -1173,6 +1196,32 @@ watchdog@fffffe40 {
 				status = "disabled";
 			};
 
+			sckc@fffffe50 {
+				compatible = "atmel,at91sam9x5-sckc";
+				reg = <0xfffffe50 0x4>;
+
+				slow_rc_osc: slow_rc_osc {
+					compatible = "atmel,at91sam9x5-clk-slow-rc-osc";
+					#clock-cells = <0>;
+					clock-frequency = <32768>;
+					clock-accuracy = <50000000>;
+					atmel,startup-time-usec = <75>;
+				};
+
+				slow_osc: slow_osc {
+					compatible = "atmel,at91sam9x5-clk-slow-osc";
+					#clock-cells = <0>;
+					clocks = <&slow_xtal>;
+					atmel,startup-time-usec = <1200000>;
+				};
+
+				clk32k: slowck {
+					compatible = "atmel,at91sam9x5-clk-slow";
+					#clock-cells = <0>;
+					clocks = <&slow_rc_osc &slow_osc>;
+				};
+			};
+
 			rtc@fffffeb0 {
 				compatible = "atmel,at91rm9200-rtc";
 				reg = <0xfffffeb0 0x30>;

arch/arm/boot/dts/sama5d3xcm.dtsi

@@ -18,6 +18,14 @@ memory {
 		reg = <0x20000000 0x20000000>;
 	};
 
+	slow_xtal {
+		clock-frequency = <32768>;
+	};
+
+	main_xtal {
+		clock-frequency = <12000000>;
+	};
+
 	ahb {
 		apb {
 			spi0: spi@f0004000 {

arch/arm/configs/at91sam9g45_defconfig

@@ -83,7 +83,6 @@ CONFIG_KEYBOARD_GPIO=y
 # CONFIG_INPUT_MOUSE is not set
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_ATMEL_MXT=m
-CONFIG_TOUCHSCREEN_ATMEL_TSADCC=y
 # CONFIG_SERIO is not set
 # CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_ATMEL=y
@@ -146,6 +145,8 @@ CONFIG_DMADEVICES=y
 CONFIG_AT_HDMAC=y
 CONFIG_DMATEST=m
 # CONFIG_IOMMU_SUPPORT is not set
+CONFIG_IIO=y
+CONFIG_AT91_ADC=y
 CONFIG_EXT4_FS=y
 CONFIG_FANOTIFY=y
 CONFIG_VFAT_FS=y

arch/arm/configs/at91sam9rl_defconfig

@@ -45,7 +45,6 @@ CONFIG_INPUT_EVDEV=y
 # CONFIG_INPUT_KEYBOARD is not set
 # CONFIG_INPUT_MOUSE is not set
 CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_TOUCHSCREEN_ATMEL_TSADCC=y
 # CONFIG_SERIO is not set
 CONFIG_SERIAL_ATMEL=y
 CONFIG_SERIAL_ATMEL_CONSOLE=y
@@ -65,6 +64,8 @@ CONFIG_MMC=y
 CONFIG_MMC_ATMELMCI=m
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_DRV_AT91SAM9=y
+CONFIG_IIO=y
+CONFIG_AT91_ADC=y
 CONFIG_EXT2_FS=y
 CONFIG_MSDOS_FS=y
 CONFIG_VFAT_FS=y

arch/arm/configs/sama5_defconfig

@@ -122,7 +122,6 @@ CONFIG_KEYBOARD_GPIO=y
 # CONFIG_INPUT_MOUSE is not set
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_ATMEL_MXT=y
-CONFIG_TOUCHSCREEN_ATMEL_TSADCC=y
 # CONFIG_SERIO is not set
 CONFIG_LEGACY_PTY_COUNT=4
 CONFIG_SERIAL_ATMEL=y

arch/arm/mach-at91/at91rm9200_devices.c

@@ -25,6 +25,7 @@
 
 #include "board.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 /* --------------------------------------------------------------------

arch/arm/mach-at91/at91sam9260_devices.c

@@ -24,12 +24,11 @@
 #include <mach/at91sam9260_matrix.h>
 #include <mach/at91_matrix.h>
 #include <mach/at91sam9_smc.h>
-#include <mach/at91_adc.h>
 #include <mach/hardware.h>
 
 #include "board.h"
 #include "generic.h"
-
+#include "gpio.h"
 
 /* --------------------------------------------------------------------
  *  USB Host
@@ -1325,13 +1324,6 @@ static struct at91_adc_trigger at91_adc_triggers[] = {
 	},
 };
 
-static struct at91_adc_reg_desc at91_adc_register_g20 = {
-	.channel_base = AT91_ADC_CHR(0),
-	.drdy_mask = AT91_ADC_DRDY,
-	.status_register = AT91_ADC_SR,
-	.trigger_register = AT91_ADC_MR,
-};
-
 void __init at91_add_device_adc(struct at91_adc_data *data)
 {
 	if (!data)
@@ -1349,9 +1341,7 @@ void __init at91_add_device_adc(struct at91_adc_data *data)
 	if (data->use_external_triggers)
 		at91_set_A_periph(AT91_PIN_PA22, 0);
 
-	data->num_channels = 4;
 	data->startup_time = 10;
-	data->registers = &at91_adc_register_g20;
 	data->trigger_number = 4;
 	data->trigger_list = at91_adc_triggers;
 

arch/arm/mach-at91/at91sam9261_devices.c

@@ -29,7 +29,7 @@
 
 #include "board.h"
 #include "generic.h"
-
+#include "gpio.h"
 
 /* --------------------------------------------------------------------
  *  USB Host

arch/arm/mach-at91/at91sam9263_devices.c

@@ -28,6 +28,7 @@
 
 #include "board.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 /* --------------------------------------------------------------------

arch/arm/mach-at91/at91sam9g45.c

@@ -182,7 +182,7 @@ static struct clk vdec_clk = {
 static struct clk adc_op_clk = {
 	.name		= "adc_op_clk",
 	.type		= CLK_TYPE_PERIPHERAL,
-	.rate_hz	= 13200000,
+	.rate_hz	= 300000,
 };
 
 /* AES/TDES/SHA clock - Only for sam9m11/sam9g56 */

arch/arm/mach-at91/at91sam9g45_devices.c

@@ -25,7 +25,6 @@
 #include <linux/fb.h>
 #include <video/atmel_lcdc.h>
 
-#include <mach/at91_adc.h>
 #include <mach/at91sam9g45.h>
 #include <mach/at91sam9g45_matrix.h>
 #include <mach/at91_matrix.h>
@@ -39,6 +38,7 @@
 #include "board.h"
 #include "generic.h"
 #include "clock.h"
+#include "gpio.h"
 
 
 /* --------------------------------------------------------------------
@@ -1133,58 +1133,7 @@ static void __init at91_add_device_rtc(void) {}
 
 
 /* --------------------------------------------------------------------
- *  Touchscreen
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_TOUCHSCREEN_ATMEL_TSADCC) || defined(CONFIG_TOUCHSCREEN_ATMEL_TSADCC_MODULE)
-static u64 tsadcc_dmamask = DMA_BIT_MASK(32);
-static struct at91_tsadcc_data tsadcc_data;
-
-static struct resource tsadcc_resources[] = {
-	[0] = {
-		.start	= AT91SAM9G45_BASE_TSC,
-		.end	= AT91SAM9G45_BASE_TSC + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9G45_ID_TSC,
-		.end	= NR_IRQS_LEGACY + AT91SAM9G45_ID_TSC,
-		.flags	= IORESOURCE_IRQ,
-	}
-};
-
-static struct platform_device at91sam9g45_tsadcc_device = {
-	.name		= "atmel_tsadcc",
-	.id		= -1,
-	.dev		= {
-				.dma_mask		= &tsadcc_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &tsadcc_data,
-	},
-	.resource	= tsadcc_resources,
-	.num_resources	= ARRAY_SIZE(tsadcc_resources),
-};
-
-void __init at91_add_device_tsadcc(struct at91_tsadcc_data *data)
-{
-	if (!data)
-		return;
-
-	at91_set_gpio_input(AT91_PIN_PD20, 0);	/* AD0_XR */
-	at91_set_gpio_input(AT91_PIN_PD21, 0);	/* AD1_XL */
-	at91_set_gpio_input(AT91_PIN_PD22, 0);	/* AD2_YT */
-	at91_set_gpio_input(AT91_PIN_PD23, 0);	/* AD3_TB */
-
-	tsadcc_data = *data;
-	platform_device_register(&at91sam9g45_tsadcc_device);
-}
-#else
-void __init at91_add_device_tsadcc(struct at91_tsadcc_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- *  ADC
+ *  ADC and touchscreen
  * -------------------------------------------------------------------- */
 
 #if IS_ENABLED(CONFIG_AT91_ADC)
@@ -1236,13 +1185,6 @@ static struct at91_adc_trigger at91_adc_triggers[] = {
 	},
 };
 
-static struct at91_adc_reg_desc at91_adc_register_g45 = {
-	.channel_base = AT91_ADC_CHR(0),
-	.drdy_mask = AT91_ADC_DRDY,
-	.status_register = AT91_ADC_SR,
-	.trigger_register = 0x08,
-};
-
 void __init at91_add_device_adc(struct at91_adc_data *data)
 {
 	if (!data)
@@ -1268,9 +1210,7 @@ void __init at91_add_device_adc(struct at91_adc_data *data)
 	if (data->use_external_triggers)
 		at91_set_A_periph(AT91_PIN_PD28, 0);
 
-	data->num_channels = 8;
 	data->startup_time = 40;
-	data->registers = &at91_adc_register_g45;
 	data->trigger_number = 4;
 	data->trigger_list = at91_adc_triggers;
 

arch/arm/mach-at91/at91sam9rl.c

@@ -153,6 +153,11 @@ static struct clk ac97_clk = {
 	.pmc_mask	= 1 << AT91SAM9RL_ID_AC97C,
 	.type		= CLK_TYPE_PERIPHERAL,
 };
+static struct clk adc_op_clk = {
+	.name		= "adc_op_clk",
+	.type		= CLK_TYPE_PERIPHERAL,
+	.rate_hz	= 1000000,
+};
 
 static struct clk *periph_clocks[] __initdata = {
 	&pioA_clk,
@@ -178,6 +183,7 @@ static struct clk *periph_clocks[] __initdata = {
 	&udphs_clk,
 	&lcdc_clk,
 	&ac97_clk,
+	&adc_op_clk,
 	// irq0
 };
 
@@ -216,6 +222,7 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioB_clk),
 	CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioC_clk),
 	CLKDEV_CON_DEV_ID(NULL, "fffffa00.gpio", &pioD_clk),
+	CLKDEV_CON_ID("adc_clk", &tsc_clk),
 };
 
 static struct clk_lookup usart_clocks_lookups[] = {

arch/arm/mach-at91/at91sam9rl_devices.c

@@ -23,9 +23,11 @@
 #include <mach/at91sam9_smc.h>
 #include <mach/hardware.h>
 #include <linux/platform_data/dma-atmel.h>
+#include <linux/platform_data/at91_adc.h>
 
 #include "board.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 /* --------------------------------------------------------------------
@@ -608,14 +610,13 @@ static void __init at91_add_device_tc(void) { }
 
 
 /* --------------------------------------------------------------------
- *  Touchscreen
+ *  ADC and Touchscreen
  * -------------------------------------------------------------------- */
 
-#if defined(CONFIG_TOUCHSCREEN_ATMEL_TSADCC) || defined(CONFIG_TOUCHSCREEN_ATMEL_TSADCC_MODULE)
-static u64 tsadcc_dmamask = DMA_BIT_MASK(32);
-static struct at91_tsadcc_data tsadcc_data;
+#if IS_ENABLED(CONFIG_AT91_ADC)
+static struct at91_adc_data adc_data;
 
-static struct resource tsadcc_resources[] = {
+static struct resource adc_resources[] = {
 	[0] = {
 		.start	= AT91SAM9RL_BASE_TSC,
 		.end	= AT91SAM9RL_BASE_TSC + SZ_16K - 1,
@@ -628,36 +629,71 @@ static struct resource tsadcc_resources[] = {
 	}
 };
 
-static struct platform_device at91sam9rl_tsadcc_device = {
-	.name		= "atmel_tsadcc",
-	.id		= -1,
-	.dev		= {
-				.dma_mask		= &tsadcc_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &tsadcc_data,
+static struct platform_device at91_adc_device = {
+	.name           = "at91sam9rl-adc",
+	.id             = -1,
+	.dev            = {
+		.platform_data  = &adc_data,
 	},
-	.resource	= tsadcc_resources,
-	.num_resources	= ARRAY_SIZE(tsadcc_resources),
+	.resource       = adc_resources,
+	.num_resources  = ARRAY_SIZE(adc_resources),
 };
 
-void __init at91_add_device_tsadcc(struct at91_tsadcc_data *data)
+static struct at91_adc_trigger at91_adc_triggers[] = {
+	[0] = {
+		.name = "external-rising",
+		.value = 1,
+		.is_external = true,
+	},
+	[1] = {
+		.name = "external-falling",
+		.value = 2,
+		.is_external = true,
+	},
+	[2] = {
+		.name = "external-any",
+		.value = 3,
+		.is_external = true,
+	},
+	[3] = {
+		.name = "continuous",
+		.value = 6,
+		.is_external = false,
+	},
+};
+
+void __init at91_add_device_adc(struct at91_adc_data *data)
 {
 	if (!data)
 		return;
 
-	at91_set_A_periph(AT91_PIN_PA17, 0);	/* AD0_XR */
-	at91_set_A_periph(AT91_PIN_PA18, 0);	/* AD1_XL */
-	at91_set_A_periph(AT91_PIN_PA19, 0);	/* AD2_YT */
-	at91_set_A_periph(AT91_PIN_PA20, 0);	/* AD3_TB */
-
-	tsadcc_data = *data;
-	platform_device_register(&at91sam9rl_tsadcc_device);
+	if (test_bit(0, &data->channels_used))
+		at91_set_A_periph(AT91_PIN_PA17, 0);
+	if (test_bit(1, &data->channels_used))
+		at91_set_A_periph(AT91_PIN_PA18, 0);
+	if (test_bit(2, &data->channels_used))
+		at91_set_A_periph(AT91_PIN_PA19, 0);
+	if (test_bit(3, &data->channels_used))
+		at91_set_A_periph(AT91_PIN_PA20, 0);
+	if (test_bit(4, &data->channels_used))
+		at91_set_A_periph(AT91_PIN_PD6, 0);
+	if (test_bit(5, &data->channels_used))
+		at91_set_A_periph(AT91_PIN_PD7, 0);
+
+	if (data->use_external_triggers)
+		at91_set_A_periph(AT91_PIN_PB15, 0);
+
+	data->startup_time = 40;
+	data->trigger_number = 4;
+	data->trigger_list = at91_adc_triggers;
+
+	adc_data = *data;
+	platform_device_register(&at91_adc_device);
 }
 #else
-void __init at91_add_device_tsadcc(struct at91_tsadcc_data *data) {}
+void __init at91_add_device_adc(struct at91_adc_data *data) {}
 #endif
 
-
 /* --------------------------------------------------------------------
  *  RTC
  * -------------------------------------------------------------------- */

arch/arm/mach-at91/board-1arm.c

@@ -39,7 +39,7 @@
 #include "at91_aic.h"
 #include "board.h"
 #include "generic.h"
-
+#include "gpio.h"
 
 static void __init onearm_init_early(void)
 {

arch/arm/mach-at91/board-afeb-9260v1.c

@@ -46,6 +46,7 @@
 #include "at91_aic.h"
 #include "board.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 static void __init afeb9260_init_early(void)

arch/arm/mach-at91/board-cam60.c

@@ -44,6 +44,7 @@
 #include "board.h"
 #include "sam9_smc.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 static void __init cam60_init_early(void)

arch/arm/mach-at91/board-carmeva.c

@@ -39,6 +39,7 @@
 #include "at91_aic.h"
 #include "board.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 static void __init carmeva_init_early(void)

arch/arm/mach-at91/board-cpu9krea.c

@@ -48,6 +48,7 @@
 #include "board.h"
 #include "sam9_smc.h"
 #include "generic.h"
+#include "gpio.h"
 
 static void __init cpu9krea_init_early(void)
 {

arch/arm/mach-at91/board-cpuat91.c

@@ -43,6 +43,8 @@
 #include "at91_aic.h"
 #include "board.h"
 #include "generic.h"
+#include "gpio.h"
+
 
 static struct gpio_led cpuat91_leds[] = {
 	{

arch/arm/mach-at91/board-csb337.c

@@ -42,7 +42,7 @@
 #include "at91_aic.h"
 #include "board.h"
 #include "generic.h"
-
+#include "gpio.h"
 
 static void __init csb337_init_early(void)
 {

arch/arm/mach-at91/board-csb637.c

@@ -39,6 +39,7 @@
 #include "at91_aic.h"
 #include "board.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 static void __init csb637_init_early(void)

arch/arm/mach-at91/board-eb9200.c

@@ -38,6 +38,7 @@
 #include "at91_aic.h"
 #include "board.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 static void __init eb9200_init_early(void)

arch/arm/mach-at91/board-ecbat91.c

@@ -42,6 +42,7 @@
 #include "at91_aic.h"
 #include "board.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 static void __init ecb_at91init_early(void)

arch/arm/mach-at91/board-eco920.c

@@ -31,6 +31,8 @@
 #include "at91_aic.h"
 #include "board.h"
 #include "generic.h"
+#include "gpio.h"
+
 
 static void __init eco920_init_early(void)
 {

arch/arm/mach-at91/board-flexibity.c

@@ -37,6 +37,7 @@
 #include "at91_aic.h"
 #include "board.h"
 #include "generic.h"
+#include "gpio.h"
 
 static void __init flexibity_init_early(void)
 {

arch/arm/mach-at91/board-foxg20.c

@@ -47,6 +47,7 @@
 #include "board.h"
 #include "sam9_smc.h"
 #include "generic.h"
+#include "gpio.h"
 
 /*
  * The FOX Board G20 hardware comes as the "Netus G20" board with

arch/arm/mach-at91/board-gsia18s.c

@@ -39,6 +39,7 @@
 #include "generic.h"
 #include "gsia18s.h"
 #include "stamp9g20.h"
+#include "gpio.h"
 
 static void __init gsia18s_init_early(void)
 {

arch/arm/mach-at91/board-kafa.c

@@ -39,6 +39,7 @@
 #include "at91_aic.h"
 #include "board.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 static void __init kafa_init_early(void)

arch/arm/mach-at91/board-kb9202.c

@@ -42,6 +42,7 @@
 #include "at91_aic.h"
 #include "board.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 static void __init kb9202_init_early(void)

arch/arm/mach-at91/board-pcontrol-g20.c

@@ -37,6 +37,7 @@
 #include "sam9_smc.h"
 #include "generic.h"
 #include "stamp9g20.h"
+#include "gpio.h"
 
 
 static void __init pcontrol_g20_init_early(void)

arch/arm/mach-at91/board-picotux200.c

@@ -43,6 +43,7 @@
 #include "at91_aic.h"
 #include "board.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 static void __init picotux200_init_early(void)

arch/arm/mach-at91/board-rm9200ek.c

@@ -45,6 +45,7 @@
 #include "at91_aic.h"
 #include "board.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 static void __init ek_init_early(void)

arch/arm/mach-at91/board-rsi-ews.c

@@ -31,6 +31,7 @@
 #include "at91_aic.h"
 #include "board.h"
 #include "generic.h"
+#include "gpio.h"
 
 static void __init rsi_ews_init_early(void)
 {

arch/arm/mach-at91/board-sam9-l9260.c

@@ -43,6 +43,7 @@
 #include "board.h"
 #include "sam9_smc.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 static void __init ek_init_early(void)

arch/arm/mach-at91/board-sam9260ek.c

@@ -49,6 +49,7 @@
 #include "board.h"
 #include "sam9_smc.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 static void __init ek_init_early(void)

arch/arm/mach-at91/board-sam9261ek.c

@@ -53,6 +53,7 @@
 #include "board.h"
 #include "sam9_smc.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 static void __init ek_init_early(void)

arch/arm/mach-at91/board-sam9263ek.c

@@ -52,6 +52,7 @@
 #include "board.h"
 #include "sam9_smc.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 static void __init ek_init_early(void)

arch/arm/mach-at91/board-sam9g20ek.c

@@ -50,6 +50,7 @@
 #include "board.h"
 #include "sam9_smc.h"
 #include "generic.h"
+#include "gpio.h"
 
 /*
  * board revision encoding

arch/arm/mach-at91/board-sam9m10g45ek.c

@@ -50,6 +50,7 @@
 #include "board.h"
 #include "sam9_smc.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 static void __init ek_init_early(void)
@@ -300,21 +301,13 @@ static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
 
 
 /*
- * Touchscreen
- */
-static struct at91_tsadcc_data ek_tsadcc_data = {
-	.adc_clock		= 300000,
-	.pendet_debounce	= 0x0d,
-	.ts_sample_hold_time	= 0x0a,
-};
-
-/*
- * ADCs
+ * ADCs and touchscreen
  */
 static struct at91_adc_data ek_adc_data = {
 	.channels_used = BIT(0) | BIT(1) | BIT(2) | BIT(3) | BIT(4) | BIT(5) | BIT(6) | BIT(7),
 	.use_external_triggers = true,
 	.vref = 3300,
+	.touchscreen_type = ATMEL_ADC_TOUCHSCREEN_4WIRE,
 };
 
 /*
@@ -485,9 +478,7 @@ static void __init ek_board_init(void)
 	at91_add_device_isi(&isi_data, true);
 	/* LCD Controller */
 	at91_add_device_lcdc(&ek_lcdc_data);
-	/* Touch Screen */
-	at91_add_device_tsadcc(&ek_tsadcc_data);
-	/* ADC */
+	/* ADC and touchscreen */
 	at91_add_device_adc(&ek_adc_data);
 	/* Push Buttons */
 	ek_add_device_buttons();

arch/arm/mach-at91/board-sam9rlek.c

@@ -18,6 +18,7 @@
 #include <linux/clk.h>
 #include <linux/input.h>
 #include <linux/gpio_keys.h>
+#include <linux/platform_data/at91_adc.h>
 
 #include <video/atmel_lcdc.h>
 
@@ -38,6 +39,7 @@
 #include "board.h"
 #include "sam9_smc.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 static void __init ek_init_early(void)
@@ -229,12 +231,13 @@ static struct gpio_led ek_leds[] = {
 
 
 /*
- * Touchscreen
+ * ADC + Touchscreen
  */
-static struct at91_tsadcc_data ek_tsadcc_data = {
-	.adc_clock		= 1000000,
-	.pendet_debounce	= 0x0f,
-	.ts_sample_hold_time	= 0x03,
+static struct at91_adc_data ek_adc_data = {
+	.channels_used = BIT(0) | BIT(1) | BIT(2) | BIT(3) | BIT(4) | BIT(5),
+	.use_external_triggers = true,
+	.vref = 3300,
+	.touchscreen_type = ATMEL_ADC_TOUCHSCREEN_4WIRE,
 };
 
 
@@ -310,8 +313,8 @@ static void __init ek_board_init(void)
 	at91_add_device_lcdc(&ek_lcdc_data);
 	/* AC97 */
 	at91_add_device_ac97(&ek_ac97_data);
-	/* Touch Screen Controller */
-	at91_add_device_tsadcc(&ek_tsadcc_data);
+	/* Touch Screen Controller + ADC */
+	at91_add_device_adc(&ek_adc_data);
 	/* LEDs */
 	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
 	/* Push Buttons */

arch/arm/mach-at91/board-snapper9260.c

@@ -38,6 +38,7 @@
 #include "board.h"
 #include "sam9_smc.h"
 #include "generic.h"
+#include "gpio.h"
 
 #define SNAPPER9260_IO_EXP_GPIO(x)	(NR_BUILTIN_GPIO + (x))
 

arch/arm/mach-at91/board-stamp9g20.c

@@ -32,6 +32,7 @@
 #include "board.h"
 #include "sam9_smc.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 void __init stamp9g20_init_early(void)

arch/arm/mach-at91/board-yl-9200.c

@@ -50,6 +50,7 @@
 #include "at91_aic.h"
 #include "board.h"
 #include "generic.h"
+#include "gpio.h"
 
 
 static void __init yl9200_init_early(void)

arch/arm/mach-at91/board.h

@@ -118,9 +118,6 @@ struct isi_platform_data;
 extern void __init at91_add_device_isi(struct isi_platform_data *data,
 		bool use_pck_as_mck);
 
- /* Touchscreen Controller */
-extern void __init at91_add_device_tsadcc(struct at91_tsadcc_data *data);
-
 /* CAN */
 extern void __init at91_add_device_can(struct at91_can_data *data);
 

arch/arm/mach-at91/gpio.c

@@ -29,6 +29,7 @@
 #include <mach/at91_pio.h>
 
 #include "generic.h"
+#include "gpio.h"
 
 #define MAX_NB_GPIO_PER_BANK	32
 

arch/arm/mach-at91/include/mach/gpio.h → arch/arm/mach-at91/gpio.h

@@ -209,14 +209,6 @@ extern int at91_get_gpio_value(unsigned pin);
 extern void at91_gpio_suspend(void);
 extern void at91_gpio_resume(void);
 
-#ifdef CONFIG_PINCTRL_AT91
-extern void at91_pinctrl_gpio_suspend(void);
-extern void at91_pinctrl_gpio_resume(void);
-#else
-static inline void at91_pinctrl_gpio_suspend(void) {}
-static inline void at91_pinctrl_gpio_resume(void) {}
-#endif
-
 #endif	/* __ASSEMBLY__ */
 
 #endif

arch/arm/mach-at91/include/mach/at91_adc.h

-/*
- * arch/arm/mach-at91/include/mach/at91_adc.h
- *
- * Copyright (C) SAN People
- *
- * Analog-to-Digital Converter (ADC) registers.
- * Based on AT91SAM9260 datasheet revision D.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef AT91_ADC_H
-#define AT91_ADC_H
-
-#define AT91_ADC_CR		0x00		/* Control Register */
-#define		AT91_ADC_SWRST		(1 << 0)	/* Software Reset */
-#define		AT91_ADC_START		(1 << 1)	/* Start Conversion */
-
-#define AT91_ADC_MR		0x04		/* Mode Register */
-#define		AT91_ADC_TRGEN		(1 << 0)	/* Trigger Enable */
-#define		AT91_ADC_TRGSEL		(7 << 1)	/* Trigger Selection */
-#define			AT91_ADC_TRGSEL_TC0		(0 << 1)
-#define			AT91_ADC_TRGSEL_TC1		(1 << 1)
-#define			AT91_ADC_TRGSEL_TC2		(2 << 1)
-#define			AT91_ADC_TRGSEL_EXTERNAL	(6 << 1)
-#define		AT91_ADC_LOWRES		(1 << 4)	/* Low Resolution */
-#define		AT91_ADC_SLEEP		(1 << 5)	/* Sleep Mode */
-#define		AT91_ADC_PRESCAL_9260	(0x3f << 8)	/* Prescalar Rate Selection */
-#define		AT91_ADC_PRESCAL_9G45	(0xff << 8)
-#define			AT91_ADC_PRESCAL_(x)	((x) << 8)
-#define		AT91_ADC_STARTUP_9260	(0x1f << 16)	/* Startup Up Time */
-#define		AT91_ADC_STARTUP_9G45	(0x7f << 16)
-#define		AT91_ADC_STARTUP_9X5	(0xf << 16)
-#define			AT91_ADC_STARTUP_(x)	((x) << 16)
-#define		AT91_ADC_SHTIM		(0xf  << 24)	/* Sample & Hold Time */
-#define			AT91_ADC_SHTIM_(x)	((x) << 24)
-
-#define AT91_ADC_CHER		0x10		/* Channel Enable Register */
-#define AT91_ADC_CHDR		0x14		/* Channel Disable Register */
-#define AT91_ADC_CHSR		0x18		/* Channel Status Register */
-#define		AT91_ADC_CH(n)		(1 << (n))	/* Channel Number */
-
-#define AT91_ADC_SR		0x1C		/* Status Register */
-#define		AT91_ADC_EOC(n)		(1 << (n))	/* End of Conversion on Channel N */
-#define		AT91_ADC_OVRE(n)	(1 << ((n) + 8))/* Overrun Error on Channel N */
-#define		AT91_ADC_DRDY		(1 << 16)	/* Data Ready */
-#define		AT91_ADC_GOVRE		(1 << 17)	/* General Overrun Error */
-#define		AT91_ADC_ENDRX		(1 << 18)	/* End of RX Buffer */
-#define		AT91_ADC_RXFUFF		(1 << 19)	/* RX Buffer Full */
-
-#define AT91_ADC_SR_9X5		0x30		/* Status Register for 9x5 */
-#define		AT91_ADC_SR_DRDY_9X5	(1 << 24)	/* Data Ready */
-
-#define AT91_ADC_LCDR		0x20		/* Last Converted Data Register */
-#define		AT91_ADC_LDATA		(0x3ff)
-
-#define AT91_ADC_IER		0x24		/* Interrupt Enable Register */
-#define AT91_ADC_IDR		0x28		/* Interrupt Disable Register */
-#define AT91_ADC_IMR		0x2C		/* Interrupt Mask Register */
-#define		AT91_ADC_IER_PEN	(1 << 29)
-#define		AT91_ADC_IER_NOPEN	(1 << 30)
-#define		AT91_ADC_IER_XRDY	(1 << 20)
-#define		AT91_ADC_IER_YRDY	(1 << 21)
-#define		AT91_ADC_IER_PRDY	(1 << 22)
-#define		AT91_ADC_ISR_PENS	(1 << 31)
-
-#define AT91_ADC_CHR(n)		(0x30 + ((n) * 4))	/* Channel Data Register N */
-#define		AT91_ADC_DATA		(0x3ff)
-
-#define AT91_ADC_CDR0_9X5	(0x50)			/* Channel Data Register 0 for 9X5 */
-
-#define AT91_ADC_ACR		0x94	/* Analog Control Register */
-#define		AT91_ADC_ACR_PENDETSENS	(0x3 << 0)	/* pull-up resistor */
-
-#define AT91_ADC_TSMR		0xB0
-#define		AT91_ADC_TSMR_TSMODE	(3 << 0)	/* Touch Screen Mode */
-#define			AT91_ADC_TSMR_TSMODE_NONE		(0 << 0)
-#define			AT91_ADC_TSMR_TSMODE_4WIRE_NO_PRESS	(1 << 0)
-#define			AT91_ADC_TSMR_TSMODE_4WIRE_PRESS	(2 << 0)
-#define			AT91_ADC_TSMR_TSMODE_5WIRE		(3 << 0)
-#define		AT91_ADC_TSMR_TSAV	(3 << 4)	/* Averages samples */
-#define			AT91_ADC_TSMR_TSAV_(x)		((x) << 4)
-#define		AT91_ADC_TSMR_SCTIM	(0x0f << 16)	/* Switch closure time */
-#define		AT91_ADC_TSMR_PENDBC	(0x0f << 28)	/* Pen Debounce time */
-#define			AT91_ADC_TSMR_PENDBC_(x)	((x) << 28)
-#define		AT91_ADC_TSMR_NOTSDMA	(1 << 22)	/* No Touchscreen DMA */
-#define		AT91_ADC_TSMR_PENDET_DIS	(0 << 24)	/* Pen contact detection disable */
-#define		AT91_ADC_TSMR_PENDET_ENA	(1 << 24)	/* Pen contact detection enable */
-
-#define AT91_ADC_TSXPOSR	0xB4
-#define AT91_ADC_TSYPOSR	0xB8
-#define AT91_ADC_TSPRESSR	0xBC
-
-#define AT91_ADC_TRGR_9260	AT91_ADC_MR
-#define AT91_ADC_TRGR_9G45	0x08
-#define AT91_ADC_TRGR_9X5	0xC0
-
-/* Trigger Register bit field */
-#define		AT91_ADC_TRGR_TRGPER	(0xffff << 16)
-#define			AT91_ADC_TRGR_TRGPER_(x)	((x) << 16)
-#define		AT91_ADC_TRGR_TRGMOD	(0x7 << 0)
-#define			AT91_ADC_TRGR_MOD_PERIOD_TRIG	(5 << 0)
-
-#endif

arch/arm/mach-at91/include/mach/hardware.h

@@ -104,5 +104,20 @@
 /* Clocks */
 #define AT91_SLOW_CLOCK		32768		/* slow clock */
 
+/*
+ * FIXME: this is needed to communicate between the pinctrl driver and
+ * the PM implementation in the machine. Possibly part of the PM
+ * implementation should be moved down into the pinctrl driver and get
+ * called as part of the generic suspend/resume path.
+ */
+#ifndef __ASSEMBLY__
+#ifdef CONFIG_PINCTRL_AT91
+extern void at91_pinctrl_gpio_suspend(void);
+extern void at91_pinctrl_gpio_resume(void);
+#else
+static inline void at91_pinctrl_gpio_suspend(void) {}
+static inline void at91_pinctrl_gpio_resume(void) {}
+#endif
+#endif
 
 #endif

arch/arm/mach-at91/leds.c

@@ -16,6 +16,7 @@
 #include <linux/platform_device.h>
 
 #include "board.h"
+#include "gpio.h"
 
 
 /* ------------------------------------------------------------------------- */

arch/arm/mach-at91/pm.c

@@ -32,6 +32,7 @@
 #include "at91_aic.h"
 #include "generic.h"
 #include "pm.h"
+#include "gpio.h"
 
 /*
  * Show the reason for the previous system reset.

drivers/clk/at91/Makefile

@@ -2,8 +2,8 @@
 # Makefile for at91 specific clk
 #
 
-obj-y += pmc.o
-obj-y += clk-main.o clk-pll.o clk-plldiv.o clk-master.o
+obj-y += pmc.o sckc.o
+obj-y += clk-slow.o clk-main.o clk-pll.o clk-plldiv.o clk-master.o
 obj-y += clk-system.o clk-peripheral.o clk-programmable.o
 
 obj-$(CONFIG_HAVE_AT91_UTMI)		+= clk-utmi.o

drivers/clk/at91/pmc.c

@@ -229,11 +229,28 @@ static struct at91_pmc *__init at91_pmc_init(struct device_node *np,
 }
 
 static const struct of_device_id pmc_clk_ids[] __initconst = {
+	/* Slow oscillator */
+	{
+		.compatible = "atmel,at91sam9260-clk-slow",
+		.data = of_at91sam9260_clk_slow_setup,
+	},
 	/* Main clock */
+	{
+		.compatible = "atmel,at91rm9200-clk-main-osc",
+		.data = of_at91rm9200_clk_main_osc_setup,
+	},
+	{
+		.compatible = "atmel,at91sam9x5-clk-main-rc-osc",
+		.data = of_at91sam9x5_clk_main_rc_osc_setup,
+	},
 	{
 		.compatible = "atmel,at91rm9200-clk-main",
 		.data = of_at91rm9200_clk_main_setup,
 	},
+	{
+		.compatible = "atmel,at91sam9x5-clk-main",
+		.data = of_at91sam9x5_clk_main_setup,
+	},
 	/* PLL clocks */
 	{
 		.compatible = "atmel,at91rm9200-clk-pll",

drivers/clk/at91/pmc.h

@@ -58,8 +58,17 @@ static inline void pmc_write(struct at91_pmc *pmc, int offset, u32 value)
 int of_at91_get_clk_range(struct device_node *np, const char *propname,
 			  struct clk_range *range);
 
+extern void __init of_at91sam9260_clk_slow_setup(struct device_node *np,
+						 struct at91_pmc *pmc);
+
+extern void __init of_at91rm9200_clk_main_osc_setup(struct device_node *np,
+						    struct at91_pmc *pmc);
+extern void __init of_at91sam9x5_clk_main_rc_osc_setup(struct device_node *np,
+						       struct at91_pmc *pmc);
 extern void __init of_at91rm9200_clk_main_setup(struct device_node *np,
 						struct at91_pmc *pmc);
+extern void __init of_at91sam9x5_clk_main_setup(struct device_node *np,
+						struct at91_pmc *pmc);
 
 extern void __init of_at91rm9200_clk_pll_setup(struct device_node *np,
 					       struct at91_pmc *pmc);

drivers/clk/at91/sckc.c

+/*
+ * drivers/clk/at91/sckc.c
+ *
+ *  Copyright (C) 2013 Boris BREZILLON <b.brezillon@overkiz.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/clkdev.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/io.h>
+
+#include "sckc.h"
+
+static const struct of_device_id sckc_clk_ids[] __initconst = {
+	/* Slow clock */
+	{
+		.compatible = "atmel,at91sam9x5-clk-slow-osc",
+		.data = of_at91sam9x5_clk_slow_osc_setup,
+	},
+	{
+		.compatible = "atmel,at91sam9x5-clk-slow-rc-osc",
+		.data = of_at91sam9x5_clk_slow_rc_osc_setup,
+	},
+	{
+		.compatible = "atmel,at91sam9x5-clk-slow",
+		.data = of_at91sam9x5_clk_slow_setup,
+	},
+	{ /*sentinel*/ }
+};
+
+static void __init of_at91sam9x5_sckc_setup(struct device_node *np)
+{
+	struct device_node *childnp;
+	void (*clk_setup)(struct device_node *, void __iomem *);
+	const struct of_device_id *clk_id;
+	void __iomem *regbase = of_iomap(np, 0);
+
+	if (!regbase)
+		return;
+
+	for_each_child_of_node(np, childnp) {
+		clk_id = of_match_node(sckc_clk_ids, childnp);
+		if (!clk_id)
+			continue;
+		clk_setup = clk_id->data;
+		clk_setup(childnp, regbase);
+	}
+}
+CLK_OF_DECLARE(at91sam9x5_clk_sckc, "atmel,at91sam9x5-sckc",
+	       of_at91sam9x5_sckc_setup);

drivers/clk/at91/sckc.h

+/*
+ * drivers/clk/at91/sckc.h
+ *
+ *  Copyright (C) 2013 Boris BREZILLON <b.brezillon@overkiz.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef __AT91_SCKC_H_
+#define __AT91_SCKC_H_
+
+extern void __init of_at91sam9x5_clk_slow_osc_setup(struct device_node *np,
+						    void __iomem *sckcr);
+extern void __init of_at91sam9x5_clk_slow_rc_osc_setup(struct device_node *np,
+						       void __iomem *sckcr);
+extern void __init of_at91sam9x5_clk_slow_setup(struct device_node *np,
+						void __iomem *sckcr);
+
+#endif /* __AT91_SCKC_H_ */

drivers/input/touchscreen/Kconfig

@@ -550,18 +550,6 @@ config TOUCHSCREEN_TI_AM335X_TSC
 	  To compile this driver as a module, choose M here: the
 	  module will be called ti_am335x_tsc.
 
-config TOUCHSCREEN_ATMEL_TSADCC
-	tristate "Atmel Touchscreen Interface"
-	depends on ARCH_AT91
-	help
-	  Say Y here if you have a 4-wire touchscreen connected to the
-          ADC Controller on your Atmel SoC.
-
-	  If unsure, say N.
-
-	  To compile this driver as a module, choose M here: the
-	  module will be called atmel_tsadcc.
-
 config TOUCHSCREEN_UCB1400
 	tristate "Philips UCB1400 touchscreen"
 	depends on AC97_BUS

drivers/input/touchscreen/Makefile

@@ -13,7 +13,6 @@ obj-$(CONFIG_TOUCHSCREEN_AD7879_I2C)	+= ad7879-i2c.o
 obj-$(CONFIG_TOUCHSCREEN_AD7879_SPI)	+= ad7879-spi.o
 obj-$(CONFIG_TOUCHSCREEN_ADS7846)	+= ads7846.o
 obj-$(CONFIG_TOUCHSCREEN_ATMEL_MXT)	+= atmel_mxt_ts.o
-obj-$(CONFIG_TOUCHSCREEN_ATMEL_TSADCC)	+= atmel_tsadcc.o
 obj-$(CONFIG_TOUCHSCREEN_AUO_PIXCIR)	+= auo-pixcir-ts.o
 obj-$(CONFIG_TOUCHSCREEN_BU21013)	+= bu21013_ts.o
 obj-$(CONFIG_TOUCHSCREEN_CY8CTMG110)	+= cy8ctmg110_ts.o

include/linux/clk/at91_pmc.h

@@ -155,6 +155,7 @@ extern void __iomem *at91_pmc_base;
 #define		AT91_PMC_LOCKB		(1 <<  2)		/* PLLB Lock */
 #define		AT91_PMC_MCKRDY		(1 <<  3)		/* Master Clock */
 #define		AT91_PMC_LOCKU		(1 <<  6)		/* UPLL Lock [some SAM9] */
+#define		AT91_PMC_OSCSEL		(1 <<  7)		/* Slow Oscillator Selection [some SAM9] */
 #define		AT91_PMC_PCK0RDY	(1 <<  8)		/* Programmable Clock 0 */
 #define		AT91_PMC_PCK1RDY	(1 <<  9)		/* Programmable Clock 1 */
 #define		AT91_PMC_PCK2RDY	(1 << 10)		/* Programmable Clock 2 */

include/linux/platform_data/at91_adc.h

@@ -7,23 +7,10 @@
 #ifndef _AT91_ADC_H_
 #define _AT91_ADC_H_
 
-/**
- * struct at91_adc_reg_desc - Various informations relative to registers
- * @channel_base:	Base offset for the channel data registers
- * @drdy_mask:		Mask of the DRDY field in the relevant registers
-			(Interruptions registers mostly)
- * @status_register:	Offset of the Interrupt Status Register
- * @trigger_register:	Offset of the Trigger setup register
- * @mr_prescal_mask:	Mask of the PRESCAL field in the adc MR register
- * @mr_startup_mask:	Mask of the STARTUP field in the adc MR register
- */
-struct at91_adc_reg_desc {
-	u8	channel_base;
-	u32	drdy_mask;
-	u8	status_register;
-	u8	trigger_register;
-	u32	mr_prescal_mask;
-	u32	mr_startup_mask;
+enum atmel_adc_ts_type {
+	ATMEL_ADC_TOUCHSCREEN_NONE = 0,
+	ATMEL_ADC_TOUCHSCREEN_4WIRE = 4,
+	ATMEL_ADC_TOUCHSCREEN_5WIRE = 5,
 };
 
 /**
@@ -42,23 +29,21 @@ struct at91_adc_trigger {
 /**
  * struct at91_adc_data - platform data for ADC driver
  * @channels_used:		channels in use on the board as a bitmask
- * @num_channels:		global number of channels available on the board
- * @registers:			Registers definition on the board
  * @startup_time:		startup time of the ADC in microseconds
  * @trigger_list:		Triggers available in the ADC
  * @trigger_number:		Number of triggers available in the ADC
  * @use_external_triggers:	does the board has external triggers availables
  * @vref:			Reference voltage for the ADC in millivolts
+ * @touchscreen_type:		If a touchscreen is connected, its type (4 or 5 wires)
  */
 struct at91_adc_data {
 	unsigned long			channels_used;
-	u8				num_channels;
-	struct at91_adc_reg_desc	*registers;
 	u8				startup_time;
 	struct at91_adc_trigger		*trigger_list;
 	u8				trigger_number;
 	bool				use_external_triggers;
 	u16				vref;
+	enum atmel_adc_ts_type		touchscreen_type;
 };
 
 extern void __init at91_add_device_adc(struct at91_adc_data *data);

include/linux/platform_data/atmel.h

@@ -87,13 +87,6 @@ struct atmel_uart_data {
 	int			rts_gpio;	/* optional RTS GPIO */
 };
 
- /* Touchscreen Controller */
-struct at91_tsadcc_data {
-	unsigned int    adc_clock;
-	u8		pendet_debounce;
-	u8		ts_sample_hold_time;
-};
-
 /* CAN */
 struct at91_can_data {
 	void (*transceiver_switch)(int on);

sound/soc/atmel/sam9g20_wm8731.c

@@ -48,7 +48,6 @@
 
 #include <asm/mach-types.h>
 #include <mach/hardware.h>
-#include <mach/gpio.h>
 
 #include "../codecs/wm8731.h"
 #include "atmel-pcm.h"