ARM: BCM5301X: Set vcc-gpio for USB controllers of few devices

There are few devices that have USB power controlled using GPIO. Linux
USB host driver (bcma-hcd) already supports this by reading vcc-gpio
from DT. Set it properly for all known devices.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts

@@ -139,3 +139,11 @@ eject {
 &uart0 {
 	status = "okay";
 };
+
+&usb2 {
+	vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+};

arch/arm/boot/dts/bcm4708-netgear-r6250.dts

@@ -24,17 +24,6 @@ memory {
 		reg = <0x00000000 0x08000000>;
 	};
 
-	axi@18000000 {
-		usb3@23000 {
-			reg = <0x00023000 0x1000>;
-
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
-		};
-	};
-
 	leds {
 		compatible = "gpio-leds";
 
@@ -97,3 +86,7 @@ restart {
 &uart0 {
 	status = "okay";
 };
+
+&usb3 {
+	vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
+};

arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts

@@ -126,3 +126,8 @@ eject {
 		};
 	};
 };
+
+
+&usb2 {
+	vcc-gpio = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
+};

arch/arm/boot/dts/bcm4709-netgear-r8000.dts

@@ -106,3 +106,11 @@ restart {
 		};
 	};
 };
+
+&usb2 {
+	vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
+};

arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts

@@ -109,3 +109,7 @@ &uart0 {
 	status = "okay";
 	clock-frequency = <125000000>;
 };
+
+&usb3 {
+	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
+};

arch/arm/boot/dts/bcm5301x.dtsi

@@ -207,6 +207,20 @@ chipcommon: chipcommon@0 {
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
+
+		usb2: usb2@21000 {
+			reg = <0x00021000 0x1000>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
+
+		usb3: usb3@23000 {
+			reg = <0x00023000 0x1000>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
 	};
 
 	lcpll0: lcpll0@1800c100 {