octeontx2-af: Workarounds for HW errata

Errata 35038
  Software sets NIX_AF_RX_SW_SYNC[ENA] to sync (flush) in-flight packets
  the RX data path before configuration changes (e.g. disabling one or
  more RQs). Hardware clears [ENA] to indicate sync is done

  An issue exists whereby NIX may clear NIX_AF_RX_SW_SYNC [ENA] too
  early.

Errata 35057
  NIX may corrupt internal state when conditional clocks turn off.
  So turnon all clocks by default.

Errata 35786
 Parse nibble enable NPC configuration for KEY generation has to be
 identical for both Rx and Tx interfaces.

Also corrected endianness configuration for NIX i.e NIX_AF_CFG[AF_BE]
is bit8 and not bit1.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/marvell/octeontx2/af/rvu.h

@@ -11,6 +11,7 @@
 #ifndef RVU_H
 #define RVU_H
 
+#include <linux/pci.h>
 #include "rvu_struct.h"
 #include "common.h"
 #include "mbox.h"
@@ -18,6 +19,9 @@
 /* PCI device IDs */
 #define	PCI_DEVID_OCTEONTX2_RVU_AF		0xA065
 
+/* Subsystem Device ID */
+#define PCI_SUBSYS_DEVID_96XX                  0xB200
+
 /* PCI BAR nos */
 #define	PCI_AF_REG_BAR_NUM			0
 #define	PCI_PF_REG_BAR_NUM			2
@@ -255,6 +259,14 @@ static inline u64 rvupf_read64(struct rvu *rvu, u64 offset)
 	return readq(rvu->pfreg_base + offset);
 }
 
+static inline bool is_rvu_9xxx_A0(struct rvu *rvu)
+{
+	struct pci_dev *pdev = rvu->pdev;
+
+	return (pdev->revision == 0x00) &&
+		(pdev->subsystem_device == PCI_SUBSYS_DEVID_96XX);
+}
+
 /* Function Prototypes
  * RVU
  */

drivers/net/ethernet/marvell/octeontx2/af/rvu_nix.c

@@ -114,6 +114,12 @@ static void nix_rx_sync(struct rvu *rvu, int blkaddr)
 	err = rvu_poll_reg(rvu, blkaddr, NIX_AF_RX_SW_SYNC, BIT_ULL(0), true);
 	if (err)
 		dev_err(rvu->dev, "NIX RX software sync failed\n");
+
+	/* As per a HW errata in 9xxx A0 silicon, HW may clear SW_SYNC[ENA]
+	 * bit too early. Hence wait for 50us more.
+	 */
+	if (is_rvu_9xxx_A0(rvu))
+		usleep_range(50, 60);
 }
 
 static bool is_valid_txschq(struct rvu *rvu, int blkaddr,
@@ -2135,10 +2141,10 @@ static int nix_aq_init(struct rvu *rvu, struct rvu_block *block)
 	/* Set admin queue endianness */
 	cfg = rvu_read64(rvu, block->addr, NIX_AF_CFG);
 #ifdef __BIG_ENDIAN
-	cfg |= BIT_ULL(1);
+	cfg |= BIT_ULL(8);
 	rvu_write64(rvu, block->addr, NIX_AF_CFG, cfg);
 #else
-	cfg &= ~BIT_ULL(1);
+	cfg &= ~BIT_ULL(8);
 	rvu_write64(rvu, block->addr, NIX_AF_CFG, cfg);
 #endif
 
@@ -2175,6 +2181,14 @@ int rvu_nix_init(struct rvu *rvu)
 		return 0;
 	block = &hw->block[blkaddr];
 
+	/* As per a HW errata in 9xxx A0 silicon, NIX may corrupt
+	 * internal state when conditional clocks are turned off.
+	 * Hence enable them.
+	 */
+	if (is_rvu_9xxx_A0(rvu))
+		rvu_write64(rvu, blkaddr, NIX_AF_CFG,
+			    rvu_read64(rvu, blkaddr, NIX_AF_CFG) | 0x5EULL);
+
 	/* Calibrate X2P bus to check if CGX/LBK links are fine */
 	err = nix_calibrate_x2p(rvu, blkaddr);
 	if (err)

drivers/net/ethernet/marvell/octeontx2/af/rvu_npc.c

@@ -970,7 +970,7 @@ int rvu_npc_init(struct rvu *rvu)
 	struct npc_pkind *pkind = &rvu->hw->pkind;
 	u64 keyz = NPC_MCAM_KEY_X2;
 	int blkaddr, entry, bank, err;
-	u64 cfg;
+	u64 cfg, nibble_ena;
 
 	blkaddr = rvu_get_blkaddr(rvu, BLKTYPE_NPC, 0);
 	if (blkaddr < 0) {
@@ -1019,10 +1019,16 @@ int rvu_npc_init(struct rvu *rvu)
 	/* Set RX and TX side MCAM search key size.
 	 * LA..LD (ltype only) + Channel
 	 */
+	nibble_ena = 0x49247;
 	rvu_write64(rvu, blkaddr, NPC_AF_INTFX_KEX_CFG(NIX_INTF_RX),
-			((keyz & 0x3) << 32) | 0x49247);
+			((keyz & 0x3) << 32) | nibble_ena);
+	/* Due to an errata (35786) in A0 pass silicon, parse nibble enable
+	 * configuration has to be identical for both Rx and Tx interfaces.
+	 */
+	if (!is_rvu_9xxx_A0(rvu))
+		nibble_ena = (1ULL << 19) - 1;
 	rvu_write64(rvu, blkaddr, NPC_AF_INTFX_KEX_CFG(NIX_INTF_TX),
-			((keyz & 0x3) << 32) | ((1ULL << 19) - 1));
+			((keyz & 0x3) << 32) | nibble_ena);
 
 	err = npc_mcam_rsrcs_init(rvu, blkaddr);
 	if (err)