Commit e15d2774 authored by Martin Blumenstingl's avatar Martin Blumenstingl Committed by Kevin Hilman

ARM64: dts: meson-gxl: add support for the Khadas VIM board

The Khadas VIM series consists of two boards which are almost
identical:
They are both using the same GXL S905X SoC, 100Mbit/s ethernet
(through the SoC-internal PHY), 2GB DDR3 memory, a micro-SD card slot,
onboard eMMC, Broadcom based SDIO WIFI, 2x USB A and 1x USB Type-C (the
latter with OTG support). The red LED is driven by PWM_AO_B (which
allows dimming), while the blue LED is managed by the firmware.
The differences are:
- the VIM Pro has a 16GB eMMC module, while the VIM only has 8GB
- the VIM Pro uses an AP6255 a/b/g/n/ac WIFI module, while the VIM comes
  with an AP6212 b/g/n SDIO WIFI module
 (the Vim uses an 8GB eMMC module, while

The boards are based on Amlogic's GXL S905X P212 reference design, which
is why most of the functionality (all MMC controllers and power
sequences, IR remote input, the main UART, ADC and ethernet) is simply
inherited from meson-gxl-s905x-p212.dtsi.
Signed-off-by: default avatarMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: default avatarNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: default avatarKevin Hilman <khilman@baylibre.com>
parent 02eff15e
...@@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-meta.dtb ...@@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-meta.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-telos.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-telos.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-wetek-hub.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-wetek-hub.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-wetek-play2.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-wetek-play2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-khadas-vim.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb
......
/*
* Copyright (c) 2017 Martin Blumenstingl <martin.blumenstingl@googlemail.com>.
*
* SPDX-License-Identifier: (GPL-2.0+ OR MIT)
*/
/dts-v1/;
#include <dt-bindings/input/input.h>
#include "meson-gxl-s905x-p212.dtsi"
/ {
compatible = "khadas,vim", "amlogic,s905x", "amlogic,meson-gxl";
model = "Khadas VIM";
adc-keys {
compatible = "adc-keys";
io-channels = <&saradc 0>;
io-channel-names = "buttons";
keyup-threshold-microvolt = <1710000>;
button-function {
label = "Function";
linux,code = <KEY_FN>;
press-threshold-microvolt = <10000>;
};
};
aliases {
serial2 = &uart_AO_B;
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <100>;
button@0 {
label = "power";
linux,code = <KEY_POWER>;
gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
};
};
pwmleds {
compatible = "pwm-leds";
power {
label = "vim:red:power";
pwms = <&pwm_AO_ab 1 7812500 0>;
max-brightness = <255>;
linux,default-trigger = "default-on";
};
};
};
&i2c_A {
status = "okay";
pinctrl-0 = <&i2c_a_pins>;
pinctrl-names = "default";
};
&i2c_B {
status = "okay";
pinctrl-0 = <&i2c_b_pins>;
pinctrl-names = "default";
rtc: rtc@51 {
/* has to be enabled manually when a battery is connected: */
status = "disabled";
compatible = "haoyu,hym8563";
reg = <0x51>;
#clock-cells = <0>;
clock-frequency = <32768>;
clock-output-names = "xin32k";
};
};
&ir {
linux,rc-map-name = "rc-geekbox";
};
&pwm_AO_ab {
status = "okay";
pinctrl-0 = <&pwm_ao_a_3_pins>, <&pwm_ao_b_pins>;
pinctrl-names = "default";
clocks = <&clkc CLKID_FCLK_DIV4>;
clock-names = "clkin0";
};
&pwm_ef {
pinctrl-0 = <&pwm_e_pins>, <&pwm_f_clk_pins>;
};
&sd_emmc_a {
brcmf: bcrmf@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
};
};
/* This is brought out on the Linux_RX (18) and Linux_TX (19) pins: */
&uart_AO {
status = "okay";
};
/* This is brought out on the UART_RX_AO_B (15) and UART_TX_AO_B (16) pins: */
&uart_AO_B {
status = "okay";
pinctrl-0 = <&uart_ao_b_pins>;
pinctrl-names = "default";
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment