Commit e4cd2ff8 authored by Ivo van Doorn's avatar Ivo van Doorn Committed by David S. Miller

rt2x00: Split rt61/rt73 antenna selection into RX and TX antenna

Based on investigation of the legacy drivers, I have made the
following assumptions of the antenna setup:
 - R77 is the TX antenna configuration
 - RF2529 fetches default antenna selection from NIC eeprom word

With these assumptions we can change the antenna configuration
to correctly read both antenna setup values and correctly
configure the antenna. And we can now also configure the antenna
for RF2529 without a double antenna.
Signed-off-by: default avatarIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: default avatarJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent e25c4bb9
......@@ -424,6 +424,29 @@ static void rt61pci_config_antenna_5x(struct rt2x00_dev *rt2x00dev,
rt2x00_set_field8(&r3, BBP_R3_SMART_MODE,
!rt2x00_rf(&rt2x00dev->chip, RF5225));
/*
* Configure the TX antenna.
*/
switch (ant->tx) {
case ANTENNA_A:
rt2x00_set_field8(&r77, BBP_R77_TX_ANTENNA, 0);
break;
case ANTENNA_SW_DIVERSITY:
case ANTENNA_HW_DIVERSITY:
/*
* NOTE: We should never come here because rt2x00lib is
* supposed to catch this and send us the correct antenna
* explicitely. However we are nog going to bug about this.
* Instead, just default to antenna B.
*/
case ANTENNA_B:
rt2x00_set_field8(&r77, BBP_R77_TX_ANTENNA, 3);
break;
}
/*
* Configure the RX antenna.
*/
switch (ant->rx) {
case ANTENNA_HW_DIVERSITY:
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA, 2);
......@@ -433,11 +456,6 @@ static void rt61pci_config_antenna_5x(struct rt2x00_dev *rt2x00dev,
case ANTENNA_A:
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA, 1);
rt2x00_set_field8(&r4, BBP_R4_RX_FRAME_END, 0);
if (rt2x00dev->curr_hwmode == HWMODE_A)
rt2x00_set_field8(&r77, BBP_R77_PAIR, 0);
else
rt2x00_set_field8(&r77, BBP_R77_PAIR, 3);
break;
case ANTENNA_SW_DIVERSITY:
/*
......@@ -449,11 +467,6 @@ static void rt61pci_config_antenna_5x(struct rt2x00_dev *rt2x00dev,
case ANTENNA_B:
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA, 1);
rt2x00_set_field8(&r4, BBP_R4_RX_FRAME_END, 0);
if (rt2x00dev->curr_hwmode == HWMODE_A)
rt2x00_set_field8(&r77, BBP_R77_PAIR, 3);
else
rt2x00_set_field8(&r77, BBP_R77_PAIR, 0);
break;
}
......@@ -478,13 +491,35 @@ static void rt61pci_config_antenna_2x(struct rt2x00_dev *rt2x00dev,
rt2x00_set_field8(&r4, BBP_R4_RX_FRAME_END,
!test_bit(CONFIG_FRAME_TYPE, &rt2x00dev->flags));
/*
* Configure the TX antenna.
*/
switch (ant->tx) {
case ANTENNA_A:
rt2x00_set_field8(&r77, BBP_R77_TX_ANTENNA, 0);
break;
case ANTENNA_SW_DIVERSITY:
case ANTENNA_HW_DIVERSITY:
/*
* NOTE: We should never come here because rt2x00lib is
* supposed to catch this and send us the correct antenna
* explicitely. However we are nog going to bug about this.
* Instead, just default to antenna B.
*/
case ANTENNA_B:
rt2x00_set_field8(&r77, BBP_R77_TX_ANTENNA, 3);
break;
}
/*
* Configure the RX antenna.
*/
switch (ant->rx) {
case ANTENNA_HW_DIVERSITY:
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA, 2);
break;
case ANTENNA_A:
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA, 1);
rt2x00_set_field8(&r77, BBP_R77_PAIR, 3);
break;
case ANTENNA_SW_DIVERSITY:
/*
......@@ -495,7 +530,6 @@ static void rt61pci_config_antenna_2x(struct rt2x00_dev *rt2x00dev,
*/
case ANTENNA_B:
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA, 1);
rt2x00_set_field8(&r77, BBP_R77_PAIR, 0);
break;
}
......@@ -530,74 +564,75 @@ static void rt61pci_config_antenna_2529(struct rt2x00_dev *rt2x00dev,
u8 r3;
u8 r4;
u8 r77;
u8 rx_ant;
rt61pci_bbp_read(rt2x00dev, 3, &r3);
rt61pci_bbp_read(rt2x00dev, 4, &r4);
rt61pci_bbp_read(rt2x00dev, 77, &r77);
rt2x00_eeprom_read(rt2x00dev, EEPROM_NIC, &eeprom);
rx_ant = !!(rt2x00_get_field16(eeprom, EEPROM_NIC_TX_RX_FIXED) & 2);
rt2x00_set_field8(&r3, BBP_R3_SMART_MODE, 0);
if (rt2x00_get_field16(eeprom, EEPROM_NIC_ENABLE_DIVERSITY) &&
rt2x00_get_field16(eeprom, EEPROM_NIC_TX_DIVERSITY)) {
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA, 2);
rt2x00_set_field8(&r4, BBP_R4_RX_FRAME_END, 1);
rt61pci_config_antenna_2529_rx(rt2x00dev, 0, 1);
} else if (rt2x00_get_field16(eeprom, EEPROM_NIC_ENABLE_DIVERSITY)) {
if (rt2x00_get_field16(eeprom, EEPROM_NIC_TX_RX_FIXED) >= 2) {
rt2x00_set_field8(&r77, BBP_R77_PAIR, 3);
rt61pci_bbp_write(rt2x00dev, 77, r77);
}
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA, 1);
rt61pci_config_antenna_2529_rx(rt2x00dev, 1, 1);
} else if (!rt2x00_get_field16(eeprom, EEPROM_NIC_ENABLE_DIVERSITY) &&
rt2x00_get_field16(eeprom, EEPROM_NIC_TX_DIVERSITY)) {
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA, 2);
rt2x00_set_field8(&r4, BBP_R4_RX_FRAME_END, 0);
/*
* Configure the TX antenna.
*/
switch (ant->tx) {
case ANTENNA_A:
rt2x00_set_field8(&r77, BBP_R77_TX_ANTENNA, 0);
break;
case ANTENNA_SW_DIVERSITY:
case ANTENNA_HW_DIVERSITY:
/*
* NOTE: We should never come here because rt2x00lib is
* supposed to catch this and send us the correct antenna
* explicitely. However we are nog going to bug about this.
* Instead, just default to antenna B.
*/
case ANTENNA_B:
rt2x00_set_field8(&r77, BBP_R77_TX_ANTENNA, 3);
break;
}
switch (rt2x00_get_field16(eeprom, EEPROM_NIC_TX_RX_FIXED)) {
case 0:
rt61pci_config_antenna_2529_rx(rt2x00dev, 0, 1);
break;
case 1:
rt61pci_config_antenna_2529_rx(rt2x00dev, 1, 0);
break;
case 2:
rt61pci_config_antenna_2529_rx(rt2x00dev, 0, 0);
break;
case 3:
rt61pci_config_antenna_2529_rx(rt2x00dev, 1, 1);
break;
}
} else if (!rt2x00_get_field16(eeprom, EEPROM_NIC_ENABLE_DIVERSITY) &&
!rt2x00_get_field16(eeprom, EEPROM_NIC_TX_DIVERSITY)) {
/*
* Configure the RX antenna.
*/
switch (ant->rx) {
case ANTENNA_A:
rt61pci_config_antenna_2529_rx(rt2x00dev, 0, rx_ant);
break;
case ANTENNA_SW_DIVERSITY:
case ANTENNA_HW_DIVERSITY:
/*
* NOTE: We should never come here because rt2x00lib is
* supposed to catch this and send us the correct antenna
* explicitely. However we are nog going to bug about this.
* Instead, just default to antenna B.
*/
case ANTENNA_B:
rt61pci_config_antenna_2529_rx(rt2x00dev, 1, rx_ant);
break;
}
/*
* FIXME: We are using the default antenna setup to
* determine the remaining settings. This because we
* need to know what the EEPROM indicated.
* It is however unclear if this is required, and overall
* using the default antenna settings here is incorrect
* since mac80211 might have told us to use fixed settings.
*/
if (rt2x00dev->default_ant.tx == ANTENNA_SW_DIVERSITY)
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA, 2);
else
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA, 1);
rt2x00_set_field8(&r4, BBP_R4_RX_FRAME_END, 0);
switch (rt2x00_get_field16(eeprom, EEPROM_NIC_TX_RX_FIXED)) {
case 0:
rt2x00_set_field8(&r77, BBP_R77_PAIR, 0);
rt61pci_bbp_write(rt2x00dev, 77, r77);
rt61pci_config_antenna_2529_rx(rt2x00dev, 0, 1);
break;
case 1:
rt2x00_set_field8(&r77, BBP_R77_PAIR, 0);
rt61pci_bbp_write(rt2x00dev, 77, r77);
rt61pci_config_antenna_2529_rx(rt2x00dev, 1, 0);
break;
case 2:
rt2x00_set_field8(&r77, BBP_R77_PAIR, 3);
rt61pci_bbp_write(rt2x00dev, 77, r77);
rt61pci_config_antenna_2529_rx(rt2x00dev, 0, 0);
break;
case 3:
rt2x00_set_field8(&r77, BBP_R77_PAIR, 3);
rt61pci_bbp_write(rt2x00dev, 77, r77);
rt61pci_config_antenna_2529_rx(rt2x00dev, 1, 1);
break;
}
}
rt2x00_set_field8(&r4, BBP_R4_RX_FRAME_END,
(rt2x00dev->default_ant.tx == ANTENNA_SW_DIVERSITY) &&
(rt2x00dev->default_ant.rx == ANTENNA_SW_DIVERSITY));
rt61pci_bbp_write(rt2x00dev, 77, r77);
rt61pci_bbp_write(rt2x00dev, 3, r3);
rt61pci_bbp_write(rt2x00dev, 4, r4);
}
......@@ -2030,6 +2065,12 @@ static int rt61pci_init_eeprom(struct rt2x00_dev *rt2x00dev)
return -ENODEV;
}
/*
* Determine number of antenna's.
*/
if (rt2x00_get_field16(eeprom, EEPROM_ANTENNA_NUM) == 2)
__set_bit(CONFIG_DOUBLE_ANTENNA, &rt2x00dev->flags);
/*
* Identify default antenna configuration.
*/
......@@ -2044,12 +2085,6 @@ static int rt61pci_init_eeprom(struct rt2x00_dev *rt2x00dev)
if (rt2x00_get_field16(eeprom, EEPROM_ANTENNA_FRAME_TYPE))
__set_bit(CONFIG_FRAME_TYPE, &rt2x00dev->flags);
/*
* Determine number of antenna's.
*/
if (rt2x00_get_field16(eeprom, EEPROM_ANTENNA_NUM) == 2)
__set_bit(CONFIG_DOUBLE_ANTENNA, &rt2x00dev->flags);
/*
* Detect if this device has an hardware controlled radio.
*/
......@@ -2077,6 +2112,38 @@ static int rt61pci_init_eeprom(struct rt2x00_dev *rt2x00dev)
if (rt2x00_get_field16(eeprom, EEPROM_NIC_EXTERNAL_LNA_BG))
__set_bit(CONFIG_EXTERNAL_LNA_BG, &rt2x00dev->flags);
/*
* When working with a RF2529 chip without double antenna
* the antenna settings should be gathered from the NIC
* eeprom word.
*/
if (rt2x00_rf(&rt2x00dev->chip, RF2529) &&
!test_bit(CONFIG_DOUBLE_ANTENNA, &rt2x00dev->flags)) {
switch (rt2x00_get_field16(eeprom, EEPROM_NIC_TX_RX_FIXED)) {
case 0:
rt2x00dev->default_ant.tx = ANTENNA_B;
rt2x00dev->default_ant.rx = ANTENNA_A;
break;
case 1:
rt2x00dev->default_ant.tx = ANTENNA_B;
rt2x00dev->default_ant.rx = ANTENNA_B;
break;
case 2:
rt2x00dev->default_ant.tx = ANTENNA_A;
rt2x00dev->default_ant.rx = ANTENNA_A;
break;
case 3:
rt2x00dev->default_ant.tx = ANTENNA_A;
rt2x00dev->default_ant.rx = ANTENNA_B;
break;
}
if (rt2x00_get_field16(eeprom, EEPROM_NIC_TX_DIVERSITY))
rt2x00dev->default_ant.tx = ANTENNA_SW_DIVERSITY;
if (rt2x00_get_field16(eeprom, EEPROM_NIC_ENABLE_DIVERSITY))
rt2x00dev->default_ant.rx = ANTENNA_SW_DIVERSITY;
}
/*
* Store led settings, for correct led behaviour.
* If the eeprom value is invalid,
......
......@@ -1083,7 +1083,7 @@ struct hw_pairwise_ta_entry {
/*
* R77
*/
#define BBP_R77_PAIR FIELD8(0x03)
#define BBP_R77_TX_ANTENNA FIELD8(0x03)
/*
* RF registers
......
......@@ -408,6 +408,29 @@ static void rt73usb_config_antenna_5x(struct rt2x00_dev *rt2x00dev,
rt2x00_set_field8(&r3, BBP_R3_SMART_MODE, 0);
/*
* Configure the TX antenna.
*/
switch (ant->tx) {
case ANTENNA_A:
rt2x00_set_field8(&r77, BBP_R77_TX_ANTENNA, 0);
break;
case ANTENNA_SW_DIVERSITY:
case ANTENNA_HW_DIVERSITY:
/*
* NOTE: We should never come here because rt2x00lib is
* supposed to catch this and send us the correct antenna
* explicitely. However we are nog going to bug about this.
* Instead, just default to antenna B.
*/
case ANTENNA_B:
rt2x00_set_field8(&r77, BBP_R77_TX_ANTENNA, 3);
break;
}
/*
* Configure the RX antenna.
*/
switch (ant->rx) {
case ANTENNA_HW_DIVERSITY:
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA, 2);
......@@ -417,11 +440,6 @@ static void rt73usb_config_antenna_5x(struct rt2x00_dev *rt2x00dev,
case ANTENNA_A:
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA, 1);
rt2x00_set_field8(&r4, BBP_R4_RX_FRAME_END, 0);
if (rt2x00dev->curr_hwmode == HWMODE_A)
rt2x00_set_field8(&r77, BBP_R77_PAIR, 0);
else
rt2x00_set_field8(&r77, BBP_R77_PAIR, 3);
break;
case ANTENNA_SW_DIVERSITY:
/*
......@@ -433,11 +451,6 @@ static void rt73usb_config_antenna_5x(struct rt2x00_dev *rt2x00dev,
case ANTENNA_B:
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA, 1);
rt2x00_set_field8(&r4, BBP_R4_RX_FRAME_END, 0);
if (rt2x00dev->curr_hwmode == HWMODE_A)
rt2x00_set_field8(&r77, BBP_R77_PAIR, 3);
else
rt2x00_set_field8(&r77, BBP_R77_PAIR, 0);
break;
}
......@@ -461,13 +474,35 @@ static void rt73usb_config_antenna_2x(struct rt2x00_dev *rt2x00dev,
rt2x00_set_field8(&r4, BBP_R4_RX_FRAME_END,
!test_bit(CONFIG_FRAME_TYPE, &rt2x00dev->flags));
/*
* Configure the TX antenna.
*/
switch (ant->tx) {
case ANTENNA_A:
rt2x00_set_field8(&r77, BBP_R77_TX_ANTENNA, 0);
break;
case ANTENNA_SW_DIVERSITY:
case ANTENNA_HW_DIVERSITY:
/*
* NOTE: We should never come here because rt2x00lib is
* supposed to catch this and send us the correct antenna
* explicitely. However we are nog going to bug about this.
* Instead, just default to antenna B.
*/
case ANTENNA_B:
rt2x00_set_field8(&r77, BBP_R77_TX_ANTENNA, 3);
break;
}
/*
* Configure the RX antenna.
*/
switch (ant->rx) {
case ANTENNA_HW_DIVERSITY:
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA, 2);
break;
case ANTENNA_A:
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA, 1);
rt2x00_set_field8(&r77, BBP_R77_PAIR, 3);
break;
case ANTENNA_SW_DIVERSITY:
/*
......@@ -478,7 +513,6 @@ static void rt73usb_config_antenna_2x(struct rt2x00_dev *rt2x00dev,
*/
case ANTENNA_B:
rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA, 1);
rt2x00_set_field8(&r77, BBP_R77_PAIR, 0);
break;
}
......
......@@ -719,7 +719,7 @@ struct hw_pairwise_ta_entry {
/*
* R77
*/
#define BBP_R77_PAIR FIELD8(0x03)
#define BBP_R77_TX_ANTENNA FIELD8(0x03)
/*
* RF registers
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment