Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (185 commits)
  powerpc: fix compile error with 85xx/p1010rdb.c
  powerpc: fix compile error with 85xx/p1023_rds.c
  powerpc/fsl: add MSI support for the Freescale hypervisor
  arch/powerpc/sysdev/fsl_rmu.c: introduce missing kfree
  powerpc/fsl: Add support for Integrated Flash Controller
  powerpc/fsl: update compatiable on fsl 16550 uart nodes
  powerpc/85xx: fix PCI and localbus properties in p1022ds.dts
  powerpc/85xx: re-enable ePAPR byte channel driver in corenet32_smp_defconfig
  powerpc/fsl: Update defconfigs to enable some standard FSL HW features
  powerpc: Add TBI PHY node to first MDIO bus
  sbc834x: put full compat string in board match check
  powerpc/fsl-pci: Allow 64-bit PCIe devices to DMA to any memory address
  powerpc: Fix unpaired probe_hcall_entry and probe_hcall_exit
  offb: Fix setting of the pseudo-palette for >8bpp
  offb: Add palette hack for qemu "standard vga" framebuffer
  offb: Fix bug in calculating requested vram size
  powerpc/boot: Change the WARN to INFO for boot wrapper overlap message
  powerpc/44x: Fix build error on currituck platform
  powerpc/boot: Change the load address for the wrapper to fit the kernel
  powerpc/44x: Enable CRASH_DUMP for 440x
  ...

Fix up a trivial conflict in arch/powerpc/include/asm/cputime.h due to
the additional sparse-checking code for cputime_t.

Documentation/devicetree/bindings/powerpc/fsl/srio-rmu.txt

+Message unit node:
+
+For SRIO controllers that implement the message unit as part of the controller
+this node is required.  For devices with RMAN this node should NOT exist.  The
+node is composed of three types of sub-nodes ("fsl-srio-msg-unit",
+"fsl-srio-dbell-unit" and "fsl-srio-port-write-unit").
+
+See srio.txt for more details about generic SRIO controller details.
+
+   - compatible
+	Usage: required
+	Value type: <string>
+	Definition: Must include "fsl,srio-rmu-vX.Y", "fsl,srio-rmu".
+
+	The version X.Y should match the general SRIO controller's IP Block
+	revision register's Major(X) and Minor (Y) value.
+
+   - reg
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: A standard property.  Specifies the physical address and
+		length of the SRIO configuration registers for message units
+		and doorbell units.
+
+   - fsl,liodn
+	Usage: optional-but-recommended (for devices with PAMU)
+	Value type: <prop-encoded-array>
+	Definition: The logical I/O device number for the PAMU (IOMMU) to be
+		correctly configured for SRIO accesses.  The property should
+		not exist on devices that do not support PAMU.
+
+		The LIODN value is associated with all RMU transactions
+		(msg-unit, doorbell, port-write).
+
+Sub-Nodes for RMU:  The RMU node is composed of multiple sub-nodes that
+correspond to the actual sub-controllers in the RMU.  The manual for a given
+SoC will detail which and how many of these sub-controllers are implemented.
+
+Message Unit:
+
+   - compatible
+	Usage: required
+	Value type: <string>
+	Definition: Must include "fsl,srio-msg-unit-vX.Y", "fsl,srio-msg-unit".
+
+	The version X.Y should match the general SRIO controller's IP Block
+	revision register's Major(X) and Minor (Y) value.
+
+   - reg
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: A standard property.  Specifies the physical address and
+		length of the SRIO configuration registers for message units
+		and doorbell units.
+
+   - interrupts
+	Usage: required
+	Value type: <prop_encoded-array>
+	Definition:  Specifies the interrupts generated by this device.  The
+		value of the interrupts property consists of one interrupt
+		specifier. The format of the specifier is defined by the
+		binding document describing the node's interrupt parent.
+
+		A pair of IRQs are specified in this property.  The first
+		element is associated with the transmit (TX) interrupt and the
+		second element is associated with the receive (RX) interrupt.
+
+Doorbell Unit:
+
+   - compatible
+	Usage: required
+	Value type: <string>
+	Definition: Must include:
+		"fsl,srio-dbell-unit-vX.Y", "fsl,srio-dbell-unit"
+
+	The version X.Y should match the general SRIO controller's IP Block
+	revision register's Major(X) and Minor (Y) value.
+
+   - reg
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: A standard property.  Specifies the physical address and
+		length of the SRIO configuration registers for message units
+		and doorbell units.
+
+   - interrupts
+	Usage: required
+	Value type: <prop_encoded-array>
+	Definition:  Specifies the interrupts generated by this device.  The
+		value of the interrupts property consists of one interrupt
+		specifier. The format of the specifier is defined by the
+		binding document describing the node's interrupt parent.
+
+		A pair of IRQs are specified in this property.  The first
+		element is associated with the transmit (TX) interrupt and the
+		second element is associated with the receive (RX) interrupt.
+
+Port-Write Unit:
+
+   - compatible
+	Usage: required
+	Value type: <string>
+	Definition: Must include:
+		 "fsl,srio-port-write-unit-vX.Y", "fsl,srio-port-write-unit"
+
+	The version X.Y should match the general SRIO controller's IP Block
+	revision register's Major(X) and Minor (Y) value.
+
+   - reg
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: A standard property.  Specifies the physical address and
+		length of the SRIO configuration registers for message units
+		and doorbell units.
+
+   - interrupts
+	Usage: required
+	Value type: <prop_encoded-array>
+	Definition:  Specifies the interrupts generated by this device.  The
+		value of the interrupts property consists of one interrupt
+		specifier. The format of the specifier is defined by the
+		binding document describing the node's interrupt parent.
+
+		A single IRQ that handles port-write conditions is
+		specified by this property.  (Typically shared with error).
+
+   Note: All other standard properties (see the ePAPR) are allowed
+   but are optional.
+
+Example:
+	rmu: rmu@d3000 {
+		compatible = "fsl,srio-rmu";
+		reg = <0xd3000 0x400>;
+		ranges = <0x0 0xd3000 0x400>;
+		fsl,liodn = <0xc8>;
+
+		message-unit@0 {
+			compatible = "fsl,srio-msg-unit";
+			reg = <0x0 0x100>;
+			interrupts = <
+				60 2 0 0  /* msg1_tx_irq */
+				61 2 0 0>;/* msg1_rx_irq */
+		};
+		message-unit@100 {
+			compatible = "fsl,srio-msg-unit";
+			reg = <0x100 0x100>;
+			interrupts = <
+				62 2 0 0  /* msg2_tx_irq */
+				63 2 0 0>;/* msg2_rx_irq */
+		};
+		doorbell-unit@400 {
+			compatible = "fsl,srio-dbell-unit";
+			reg = <0x400 0x80>;
+			interrupts = <
+				56 2 0 0  /* bell_outb_irq */
+				57 2 0 0>;/* bell_inb_irq */
+		};
+		port-write-unit@4e0 {
+			compatible = "fsl,srio-port-write-unit";
+			reg = <0x4e0 0x20>;
+			interrupts = <16 2 1 11>;
+		};
+	};

Documentation/devicetree/bindings/powerpc/fsl/srio.txt

+* Freescale Serial RapidIO (SRIO) Controller
+
+RapidIO port node:
+Properties:
+   - compatible
+	Usage: required
+	Value type: <string>
+	Definition: Must include "fsl,srio" for IP blocks with IP Block
+	Revision Register (SRIO IPBRR1) Major ID equal to 0x01c0.
+
+	Optionally, a compatiable string of "fsl,srio-vX.Y" where X is Major
+	version in IP Block Revision Register and Y is Minor version.  If this
+	compatiable is provided it should be ordered before "fsl,srio".
+
+   - reg
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: A standard property.  Specifies the physical address and
+		length of the SRIO configuration registers.  The size should
+		be set to 0x11000.
+
+   - interrupts
+	Usage: required
+	Value type: <prop_encoded-array>
+	Definition:  Specifies the interrupts generated by this device.  The
+		value of the interrupts property consists of one interrupt
+		specifier. The format of the specifier is defined by the
+		binding document describing the node's interrupt parent.
+
+		A single IRQ that handles error conditions is specified by this
+		property.  (Typically shared with port-write).
+
+   - fsl,srio-rmu-handle:
+	Usage: required if rmu node is defined
+	Value type: <phandle>
+	Definition: A single <phandle> value that points to the RMU.
+	(See srio-rmu.txt for more details on RMU node binding)
+
+Port Child Nodes:  There should a port child node for each port that exists in
+the controller.  The ports are numbered starting at one (1) and should have
+the following properties:
+
+   - cell-index
+	Usage: required
+	Value type: <u32>
+	Definition: A standard property.  Matches the port id.
+
+   - ranges
+	Usage: required if local access windows preset
+	Value type: <prop-encoded-array>
+	Definition: A standard property. Utilized to describe the memory mapped
+		IO space utilized by the controller.  This corresponds to the
+		setting of the local access windows that are targeted to this
+		SRIO port.
+
+   - fsl,liodn
+	Usage: optional-but-recommended (for devices with PAMU)
+	Value type: <prop-encoded-array>
+	Definition: The logical I/O device number for the PAMU (IOMMU) to be
+		correctly configured for SRIO accesses.  The property should
+		not exist on devices that do not support PAMU.
+
+		For HW (ie, the P4080) that only supports a LIODN for both
+		memory and maintenance transactions then a single LIODN is
+		represented in the property for both transactions.
+
+		For HW (ie, the P304x/P5020, etc) that supports an LIODN for
+		memory transactions and a unique LIODN for maintenance
+		transactions then a pair of LIODNs are represented in the
+		property.  Within the pair, the first element represents the
+		LIODN associated with memory transactions and the second element
+		represents the LIODN associated with maintenance transactions
+		for the port.
+
+Note: All other standard properties (see ePAPR) are allowed but are optional.
+
+Example:
+
+	rapidio: rapidio@ffe0c0000 {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		reg = <0xf 0xfe0c0000 0 0x11000>;
+		compatible = "fsl,srio";
+		interrupts = <16 2 1 11>; /* err_irq */
+		fsl,srio-rmu-handle = <&rmu>;
+		ranges;
+
+		port1 {
+			cell-index = <1>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			fsl,liodn = <34>;
+			ranges = <0 0 0xc 0x20000000 0 0x10000000>;
+		};
+
+		port2 {
+			cell-index = <2>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			fsl,liodn = <48>;
+			ranges = <0 0 0xc 0x30000000 0 0x10000000>;
+		};
+	};

MAINTAINERS

@@ -4011,7 +4011,7 @@ M:	Josh Boyer <jwboyer@gmail.com>
 M:	Matt Porter <mporter@kernel.crashing.org>
 W:	http://www.penguinppc.org/
 L:	linuxppc-dev@lists.ozlabs.org
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jwboyer/powerpc-4xx.git
+T:	git git://git.infradead.org/users/jwboyer/powerpc-4xx.git
 S:	Maintained
 F:	arch/powerpc/platforms/40x/
 F:	arch/powerpc/platforms/44x/

arch/powerpc/Kconfig

@@ -87,6 +87,10 @@ config ARCH_HAS_ILOG2_U64
 	bool
 	default y if 64BIT
 
+config ARCH_HAS_CPU_IDLE_WAIT
+	bool
+	default y
+
 config GENERIC_HWEIGHT
 	bool
 	default y
@@ -133,6 +137,7 @@ config PPC
 	select IRQ_PER_CPU
 	select GENERIC_IRQ_SHOW
 	select GENERIC_IRQ_SHOW_LEVEL
+	select IRQ_FORCED_THREADING
 	select HAVE_RCU_TABLE_FREE if SMP
 	select HAVE_SYSCALL_TRACEPOINTS
 	select HAVE_BPF_JIT if (PPC64 && NET)
@@ -363,8 +368,9 @@ config KEXEC
 
 config CRASH_DUMP
 	bool "Build a kdump crash kernel"
-	depends on PPC64 || 6xx || FSL_BOOKE
-	select RELOCATABLE if PPC64 || FSL_BOOKE
+	depends on PPC64 || 6xx || FSL_BOOKE || (44x && !SMP && !PPC_47x)
+	select RELOCATABLE if PPC64 || 44x
+	select DYNAMIC_MEMSTART if FSL_BOOKE
 	help
 	  Build a kernel suitable for use as a kdump capture kernel.
 	  The same kernel binary can be used as production kernel and dump
@@ -685,6 +691,10 @@ config FSL_LBC
 	  controller.  Also contains some common code used by
 	  drivers for specific local bus peripherals.
 
+config FSL_IFC
+	bool
+        depends on FSL_SOC
+
 config FSL_GTM
 	bool
 	depends on PPC_83xx || QUICC_ENGINE || CPM2
@@ -770,6 +780,10 @@ source "drivers/rapidio/Kconfig"
 
 endmenu
 
+config NONSTATIC_KERNEL
+	bool
+	default n
+
 menu "Advanced setup"
 	depends on PPC32
 
@@ -819,13 +833,32 @@ config LOWMEM_CAM_NUM
 	int "Number of CAMs to use to map low memory" if LOWMEM_CAM_NUM_BOOL
 	default 3
 
+config DYNAMIC_MEMSTART
+	bool "Enable page aligned dynamic load address for kernel (EXPERIMENTAL)"
+	depends on EXPERIMENTAL && ADVANCED_OPTIONS && FLATMEM && (FSL_BOOKE || 44x)
+	select NONSTATIC_KERNEL
+	help
+	  This option enables the kernel to be loaded at any page aligned
+	  physical address. The kernel creates a mapping from KERNELBASE to 
+	  the address where the kernel is loaded. The page size here implies
+	  the TLB page size of the mapping for kernel on the particular platform.
+	  Please refer to the init code for finding the TLB page size.
+
+	  DYNAMIC_MEMSTART is an easy way of implementing pseudo-RELOCATABLE
+	  kernel image, where the only restriction is the page aligned kernel
+	  load address. When this option is enabled, the compile time physical 
+	  address CONFIG_PHYSICAL_START is ignored.
+
+	  This option is overridden by CONFIG_RELOCATABLE
+
 config RELOCATABLE
 	bool "Build a relocatable kernel (EXPERIMENTAL)"
-	depends on EXPERIMENTAL && ADVANCED_OPTIONS && FLATMEM && (FSL_BOOKE || PPC_47x)
+	depends on EXPERIMENTAL && ADVANCED_OPTIONS && FLATMEM && 44x
+	select NONSTATIC_KERNEL
 	help
 	  This builds a kernel image that is capable of running at the
-	  location the kernel is loaded at (some alignment restrictions may
-	  exist).
+	  location the kernel is loaded at, without any alignment restrictions.
+	  This feature is a superset of DYNAMIC_MEMSTART and hence overrides it.
 
 	  One use is for the kexec on panic case where the recovery kernel
 	  must live at a different physical address than the primary
@@ -835,7 +868,11 @@ config RELOCATABLE
 	  it has been loaded at and the compile time physical addresses
 	  CONFIG_PHYSICAL_START is ignored.  However CONFIG_PHYSICAL_START
 	  setting can still be useful to bootwrappers that need to know the
-	  load location of the kernel (eg. u-boot/mkimage).
+	  load address of the kernel (eg. u-boot/mkimage).
+
+config RELOCATABLE_PPC32
+	def_bool y
+	depends on PPC32 && RELOCATABLE
 
 config PAGE_OFFSET_BOOL
 	bool "Set custom page offset address"
@@ -865,7 +902,7 @@ config KERNEL_START_BOOL
 config KERNEL_START
 	hex "Virtual address of kernel base" if KERNEL_START_BOOL
 	default PAGE_OFFSET if PAGE_OFFSET_BOOL
-	default "0xc2000000" if CRASH_DUMP && !RELOCATABLE
+	default "0xc2000000" if CRASH_DUMP && !NONSTATIC_KERNEL
 	default "0xc0000000"
 
 config PHYSICAL_START_BOOL
@@ -878,7 +915,7 @@ config PHYSICAL_START_BOOL
 
 config PHYSICAL_START
 	hex "Physical address where the kernel is loaded" if PHYSICAL_START_BOOL
-	default "0x02000000" if PPC_STD_MMU && CRASH_DUMP && !RELOCATABLE
+	default "0x02000000" if PPC_STD_MMU && CRASH_DUMP && !NONSTATIC_KERNEL
 	default "0x00000000"
 
 config PHYSICAL_ALIGN
@@ -924,6 +961,7 @@ endmenu
 if PPC64
 config RELOCATABLE
 	bool "Build a relocatable kernel"
+	select NONSTATIC_KERNEL
 	help
 	  This builds a kernel image that is capable of running anywhere
 	  in the RMA (real memory area) at any 16k-aligned base address.

arch/powerpc/Kconfig.debug

@@ -336,4 +336,16 @@ config PPC_EARLY_DEBUG_CPM_ADDR
 	  platform probing is done, all platforms selected must
 	  share the same address.
 
+config STRICT_DEVMEM
+	def_bool y
+	prompt "Filter access to /dev/mem"
+	help
+	  This option restricts access to /dev/mem.  If this option is
+	  disabled, you allow userspace access to all memory, including
+	  kernel and userspace memory. Accidental memory access is likely
+	  to be disastrous.
+	  Memory access is required for experts who want to debug the kernel.
+
+	  If you are unsure, say Y.
+
 endmenu

arch/powerpc/Makefile

@@ -63,9 +63,9 @@ override CC	+= -m$(CONFIG_WORD_SIZE)
 override AR	:= GNUTARGET=elf$(CONFIG_WORD_SIZE)-powerpc $(AR)
 endif
 
-LDFLAGS_vmlinux-yy := -Bstatic
-LDFLAGS_vmlinux-$(CONFIG_PPC64)$(CONFIG_RELOCATABLE) := -pie
-LDFLAGS_vmlinux	:= $(LDFLAGS_vmlinux-yy)
+LDFLAGS_vmlinux-y := -Bstatic
+LDFLAGS_vmlinux-$(CONFIG_RELOCATABLE) := -pie
+LDFLAGS_vmlinux	:= $(LDFLAGS_vmlinux-y)
 
 CFLAGS-$(CONFIG_PPC64)	:= -mminimal-toc -mtraceback=no -mcall-aixdesc
 CFLAGS-$(CONFIG_PPC32)	:= -ffixed-r2 -mmultiple
@@ -131,8 +131,7 @@ KBUILD_CFLAGS		+= -mno-sched-epilog
 endif
 
 cpu-as-$(CONFIG_4xx)		+= -Wa,-m405
-cpu-as-$(CONFIG_6xx)		+= -Wa,-maltivec
-cpu-as-$(CONFIG_POWER4)		+= -Wa,-maltivec
+cpu-as-$(CONFIG_ALTIVEC)	+= -Wa,-maltivec
 cpu-as-$(CONFIG_E500)		+= -Wa,-me500
 cpu-as-$(CONFIG_E200)		+= -Wa,-me200
 
@@ -166,7 +165,7 @@ all: zImage
 
 # With make 3.82 we cannot mix normal and wildcard targets
 BOOT_TARGETS1 := zImage zImage.initrd uImage
-BOOT_TARGETS2 := zImage% dtbImage% treeImage.% cuImage.% simpleImage.%
+BOOT_TARGETS2 := zImage% dtbImage% treeImage.% cuImage.% simpleImage.% uImage.%
 
 PHONY += $(BOOT_TARGETS1) $(BOOT_TARGETS2)
 

arch/powerpc/boot/Makefile

@@ -45,6 +45,7 @@ $(obj)/cuboot-katmai.o: BOOTCFLAGS += -mcpu=405
 $(obj)/cuboot-acadia.o: BOOTCFLAGS += -mcpu=405
 $(obj)/treeboot-walnut.o: BOOTCFLAGS += -mcpu=405
 $(obj)/treeboot-iss4xx.o: BOOTCFLAGS += -mcpu=405
+$(obj)/treeboot-currituck.o: BOOTCFLAGS += -mcpu=405
 $(obj)/virtex405-head.o: BOOTAFLAGS += -mcpu=405
 
 
@@ -79,7 +80,8 @@ src-plat := of.c cuboot-52xx.c cuboot-824x.c cuboot-83xx.c cuboot-85xx.c holly.c
 		cuboot-warp.c cuboot-85xx-cpm2.c cuboot-yosemite.c simpleboot.c \
 		virtex405-head.S virtex.c redboot-83xx.c cuboot-sam440ep.c \
 		cuboot-acadia.c cuboot-amigaone.c cuboot-kilauea.c \
-		gamecube-head.S gamecube.c wii-head.S wii.c treeboot-iss4xx.c
+		gamecube-head.S gamecube.c wii-head.S wii.c treeboot-iss4xx.c \
+		treeboot-currituck.c
 src-boot := $(src-wlib) $(src-plat) empty.c
 
 src-boot := $(addprefix $(obj)/, $(src-boot))
@@ -199,6 +201,7 @@ image-$(CONFIG_EP405)			+= dtbImage.ep405
 image-$(CONFIG_HOTFOOT)			+= cuImage.hotfoot
 image-$(CONFIG_WALNUT)			+= treeImage.walnut
 image-$(CONFIG_ACADIA)			+= cuImage.acadia
+image-$(CONFIG_OBS600)			+= uImage.obs600
 
 # Board ports in arch/powerpc/platform/44x/Kconfig
 image-$(CONFIG_EBONY)			+= treeImage.ebony cuImage.ebony
@@ -212,6 +215,7 @@ image-$(CONFIG_WARP)			+= cuImage.warp
 image-$(CONFIG_YOSEMITE)		+= cuImage.yosemite
 image-$(CONFIG_ISS4xx)			+= treeImage.iss4xx \
 					   treeImage.iss4xx-mpic
+image-$(CONFIG_CURRITUCK)			+= treeImage.currituck
 
 # Board ports in arch/powerpc/platform/8xx/Kconfig
 image-$(CONFIG_MPC86XADS)		+= cuImage.mpc866ads
@@ -316,6 +320,12 @@ $(obj)/zImage.iseries: vmlinux
 $(obj)/uImage: vmlinux $(wrapperbits)
 	$(call if_changed,wrap,uboot)
 
+$(obj)/uImage.initrd.%: vmlinux $(obj)/%.dtb $(wrapperbits)
+	$(call if_changed,wrap,uboot-$*,,$(obj)/$*.dtb,$(obj)/ramdisk.image.gz)
+
+$(obj)/uImage.%: vmlinux $(obj)/%.dtb $(wrapperbits)
+	$(call if_changed,wrap,uboot-$*,,$(obj)/$*.dtb)
+
 $(obj)/cuImage.initrd.%: vmlinux $(obj)/%.dtb $(wrapperbits)
 	$(call if_changed,wrap,cuboot-$*,,$(obj)/$*.dtb,$(obj)/ramdisk.image.gz)
 

arch/powerpc/boot/dcr.h

@@ -9,6 +9,12 @@
 	})
 #define mtdcr(rn, val) \
 	asm volatile("mtdcr %0,%1" : : "i"(rn), "r"(val))
+#define mfdcrx(rn) \
+	({	\
+		unsigned long rval; \
+		asm volatile("mfdcrx %0,%1" : "=r"(rval) : "r"(rn)); \
+		rval; \
+	})
 
 /* 440GP/440GX SDRAM controller DCRs */
 #define DCRN_SDRAM0_CFGADDR				0x010

arch/powerpc/boot/div64.S

@@ -57,3 +57,55 @@ __div64_32:
 	stw	r8,4(r3)
 	mr	r3,r6		# return the remainder in r3
 	blr
+
+/*
+ * Extended precision shifts.
+ *
+ * Updated to be valid for shift counts from 0 to 63 inclusive.
+ * -- Gabriel
+ *
+ * R3/R4 has 64 bit value
+ * R5    has shift count
+ * result in R3/R4
+ *
+ *  ashrdi3: arithmetic right shift (sign propagation)	
+ *  lshrdi3: logical right shift
+ *  ashldi3: left shift
+ */
+	.globl __ashrdi3
+__ashrdi3:
+	subfic	r6,r5,32
+	srw	r4,r4,r5	# LSW = count > 31 ? 0 : LSW >> count
+	addi	r7,r5,32	# could be xori, or addi with -32
+	slw	r6,r3,r6	# t1 = count > 31 ? 0 : MSW << (32-count)
+	rlwinm	r8,r7,0,32	# t3 = (count < 32) ? 32 : 0
+	sraw	r7,r3,r7	# t2 = MSW >> (count-32)
+	or	r4,r4,r6	# LSW |= t1
+	slw	r7,r7,r8	# t2 = (count < 32) ? 0 : t2
+	sraw	r3,r3,r5	# MSW = MSW >> count
+	or	r4,r4,r7	# LSW |= t2
+	blr
+
+	.globl __ashldi3
+__ashldi3:
+	subfic	r6,r5,32
+	slw	r3,r3,r5	# MSW = count > 31 ? 0 : MSW << count
+	addi	r7,r5,32	# could be xori, or addi with -32
+	srw	r6,r4,r6	# t1 = count > 31 ? 0 : LSW >> (32-count)
+	slw	r7,r4,r7	# t2 = count < 32 ? 0 : LSW << (count-32)
+	or	r3,r3,r6	# MSW |= t1
+	slw	r4,r4,r5	# LSW = LSW << count
+	or	r3,r3,r7	# MSW |= t2
+	blr
+
+	.globl __lshrdi3
+__lshrdi3:
+	subfic	r6,r5,32
+	srw	r4,r4,r5	# LSW = count > 31 ? 0 : LSW >> count
+	addi	r7,r5,32	# could be xori, or addi with -32
+	slw	r6,r3,r6	# t1 = count > 31 ? 0 : MSW << (32-count)
+	srw	r7,r3,r7	# t2 = count < 32 ? 0 : MSW >> (count-32)
+	or	r4,r4,r6	# LSW |= t1
+	srw	r3,r3,r5	# MSW = MSW >> count
+	or	r4,r4,r7	# LSW |= t2
+	blr

arch/powerpc/boot/dts/asp834x-redboot.dts

@@ -256,7 +256,7 @@ tbi1: tbi-phy@11 {
 		serial0: serial@4500 {
 			cell-index = <0>;
 			device_type = "serial";
-			compatible = "ns16550";
+			compatible = "fsl,ns16550", "ns16550";
 			reg = <0x4500 0x100>;
 			clock-frequency = <400000000>;
 			interrupts = <9 0x8>;
@@ -266,7 +266,7 @@ serial0: serial@4500 {
 		serial1: serial@4600 {
 			cell-index = <1>;
 			device_type = "serial";
-			compatible = "ns16550";
+			compatible = "fsl,ns16550", "ns16550";
 			reg = <0x4600 0x100>;
 			clock-frequency = <400000000>;
 			interrupts = <10 0x8>;

arch/powerpc/boot/dts/currituck.dts

+/*
+ * Device Tree Source for IBM Embedded PPC 476 Platform
+ *
+ * Copyright © 2011 Tony Breeds IBM Corporation
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+/memreserve/ 0x01f00000 0x00100000;	// spin table
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+	model = "ibm,currituck";
+	compatible = "ibm,currituck";
+	dcr-parent = <&{/cpus/cpu@0}>;
+
+	aliases {
+		serial0 = &UART0;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			model = "PowerPC,476";
+			reg = <0>;
+			clock-frequency = <1600000000>; // 1.6 GHz
+			timebase-frequency = <100000000>; // 100Mhz
+			i-cache-line-size = <32>;
+			d-cache-line-size = <32>;
+			i-cache-size = <32768>;
+			d-cache-size = <32768>;
+			dcr-controller;
+			dcr-access-method = "native";
+			status = "ok";
+		};
+		cpu@1 {
+			device_type = "cpu";
+			model = "PowerPC,476";
+			reg = <1>;
+			clock-frequency = <1600000000>; // 1.6 GHz
+			timebase-frequency = <100000000>; // 100Mhz
+			i-cache-line-size = <32>;
+			d-cache-line-size = <32>;
+			i-cache-size = <32768>;
+			d-cache-size = <32768>;
+			dcr-controller;
+			dcr-access-method = "native";
+			status = "disabled";
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0x01f00000>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x0>; // filled in by zImage
+	};
+
+	MPIC: interrupt-controller {
+		compatible = "chrp,open-pic";
+		interrupt-controller;
+		dcr-reg = <0xffc00000 0x00040000>;
+		#address-cells = <0>;
+		#size-cells = <0>;
+		#interrupt-cells = <2>;
+
+	};
+
+	plb {
+		compatible = "ibm,plb6";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		clock-frequency = <200000000>; // 200Mhz
+
+		POB0: opb {
+			compatible = "ibm,opb-4xx", "ibm,opb";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			/* Wish there was a nicer way of specifying a full
+			 * 32-bit range
+			 */
+			ranges = <0x00000000 0x00000200 0x00000000 0x80000000
+				  0x80000000 0x00000200 0x80000000 0x80000000>;
+			clock-frequency = <100000000>;
+
+			UART0: serial@10000000 {
+				device_type = "serial";
+				compatible = "ns16750", "ns16550";
+				reg = <0x10000000 0x00000008>;
+				virtual-reg = <0xe1000000>;
+				clock-frequency = <1851851>; // PCIe refclk/MCGC0_CTL[UART]
+				current-speed = <115200>;
+				interrupt-parent = <&MPIC>;
+				interrupts = <34 2>;
+			};
+
+			IIC0: i2c@00000000 {
+				compatible = "ibm,iic-currituck", "ibm,iic";
+				reg = <0x0 0x00000014>;
+				interrupt-parent = <&MPIC>;
+				interrupts = <79 2>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+                                rtc@68 {
+                                        compatible = "stm,m41t80", "m41st85";
+                                        reg = <0x68>;
+                                };
+			};
+		};
+
+		PCIE0: pciex@10100000000 {		// 4xGBIF1
+			device_type = "pci";
+			#interrupt-cells = <1>;
+			#size-cells = <2>;
+			#address-cells = <3>;
+			compatible = "ibm,plb-pciex-476fpe", "ibm,plb-pciex";
+			primary;
+			port = <0x0>; /* port number */
+			reg = <0x00000101 0x00000000 0x0 0x10000000		/* Config space access */
+			       0x00000100 0x00000000 0x0 0x00001000>;	/* UTL Registers space access */
+			dcr-reg = <0x80 0x20>;
+
+//                                pci_space  < pci_addr          > < cpu_addr          > < size       >
+			ranges = <0x02000000 0x00000000 0x80000000 0x00000110 0x80000000 0x0 0x80000000
+			          0x01000000 0x0        0x0        0x00000140 0x0        0x0 0x00010000>;
+
+			/* Inbound starting at 0 to memsize filled in by zImage */
+			dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x0>;
+
+			/* This drives busses 0 to 0xf */
+			bus-range = <0x0 0xf>;
+
+			/* Legacy interrupts (note the weird polarity, the bridge seems
+			 * to invert PCIe legacy interrupts).
+			 * We are de-swizzling here because the numbers are actually for
+			 * port of the root complex virtual P2P bridge. But I want
+			 * to avoid putting a node for it in the tree, so the numbers
+			 * below are basically de-swizzled numbers.
+			 * The real slot is on idsel 0, so the swizzling is 1:1
+			 */
+			interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+			interrupt-map = <
+				0x0 0x0 0x0 0x1 &MPIC 46 0x2 /* int A */
+				0x0 0x0 0x0 0x2 &MPIC 47 0x2 /* int B */
+				0x0 0x0 0x0 0x3 &MPIC 48 0x2 /* int C */
+				0x0 0x0 0x0 0x4 &MPIC 49 0x2 /* int D */>;
+		};
+
+		PCIE1: pciex@30100000000 {		// 4xGBIF0
+			device_type = "pci";
+			#interrupt-cells = <1>;
+			#size-cells = <2>;
+			#address-cells = <3>;
+			compatible = "ibm,plb-pciex-476fpe", "ibm,plb-pciex";
+			primary;
+			port = <0x1>; /* port number */
+			reg = <0x00000301 0x00000000 0x0 0x10000000		/* Config space access */
+			       0x00000300 0x00000000 0x0 0x00001000>;	/* UTL Registers space access */
+			dcr-reg = <0x60 0x20>;
+
+			ranges = <0x02000000 0x00000000 0x80000000 0x00000310 0x80000000 0x0 0x80000000
+			          0x01000000 0x0        0x0        0x00000340 0x0        0x0 0x00010000>;
+
+			/* Inbound starting at 0 to memsize filled in by zImage */
+			dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x0>;
+
+			/* This drives busses 0 to 0xf */
+			bus-range = <0x0 0xf>;
+
+			/* Legacy interrupts (note the weird polarity, the bridge seems
+			 * to invert PCIe legacy interrupts).
+			 * We are de-swizzling here because the numbers are actually for
+			 * port of the root complex virtual P2P bridge. But I want
+			 * to avoid putting a node for it in the tree, so the numbers
+			 * below are basically de-swizzled numbers.
+			 * The real slot is on idsel 0, so the swizzling is 1:1
+			 */
+			interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+			interrupt-map = <
+				0x0 0x0 0x0 0x1 &MPIC 38 0x2 /* int A */
+				0x0 0x0 0x0 0x2 &MPIC 39 0x2 /* int B */
+				0x0 0x0 0x0 0x3 &MPIC 40 0x2 /* int C */
+				0x0 0x0 0x0 0x4 &MPIC 41 0x2 /* int D */>;
+		};
+
+		PCIE2: pciex@38100000000 {		// 2xGBIF0
+			device_type = "pci";
+			#interrupt-cells = <1>;
+			#size-cells = <2>;
+			#address-cells = <3>;
+			compatible = "ibm,plb-pciex-476fpe", "ibm,plb-pciex";
+			primary;
+			port = <0x2>; /* port number */
+			reg = <0x00000381 0x00000000 0x0 0x10000000		/* Config space access */
+			       0x00000380 0x00000000 0x0 0x00001000>;	/* UTL Registers space access */
+			dcr-reg = <0xA0 0x20>;
+
+			ranges = <0x02000000 0x00000000 0x80000000 0x00000390 0x80000000 0x0 0x80000000
+			          0x01000000 0x0        0x0        0x000003C0 0x0        0x0 0x00010000>;
+
+			/* Inbound starting at 0 to memsize filled in by zImage */
+			dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x0>;
+
+			/* This drives busses 0 to 0xf */
+			bus-range = <0x0 0xf>;
+
+			/* Legacy interrupts (note the weird polarity, the bridge seems
+			 * to invert PCIe legacy interrupts).
+			 * We are de-swizzling here because the numbers are actually for
+			 * port of the root complex virtual P2P bridge. But I want
+			 * to avoid putting a node for it in the tree, so the numbers
+			 * below are basically de-swizzled numbers.
+			 * The real slot is on idsel 0, so the swizzling is 1:1
+			 */
+			interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+			interrupt-map = <
+				0x0 0x0 0x0 0x1 &MPIC 54 0x2 /* int A */
+				0x0 0x0 0x0 0x2 &MPIC 55 0x2 /* int B */
+				0x0 0x0 0x0 0x3 &MPIC 56 0x2 /* int C */
+				0x0 0x0 0x0 0x4 &MPIC 57 0x2 /* int D */>;
+		};
+
+	};
+
+	chosen {
+		linux,stdout-path = &UART0;
+	};
+};

arch/powerpc/boot/dts/fsl/mpc8536si-post.dtsi

+/*
+ * MPC8536 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	compatible = "fsl,mpc8536-elbc", "fsl,elbc", "simple-bus";
+	interrupts = <19 2 0 0>;
+};
+
+/* controller at 0x8000 */
+&pci0 {
+	compatible = "fsl,mpc8540-pci";
+	device_type = "pci";
+	interrupts = <24 0x2 0 0>;
+	bus-range = <0 0xff>;
+	#interrupt-cells = <1>;
+	#size-cells = <2>;
+	#address-cells = <3>;
+};
+
+/* controller at 0x9000 */
+&pci1 {
+	compatible = "fsl,mpc8548-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <25 2 0 0>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <25 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x4 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x5 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0x6 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0x7 0x1 0x0 0x0
+			>;
+	};
+};
+
+/* controller at 0xa000 */
+&pci2 {
+	compatible = "fsl,mpc8548-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <26 2 0 0>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <26 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x0 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x1 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0x2 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0x3 0x1 0x0 0x0
+			>;
+	};
+};
+
+/* controller at 0xb000 */
+&pci3 {
+	compatible = "fsl,mpc8548-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <27 2 0 0>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <27 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x8 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x9 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0xa 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0xb 0x1 0x0 0x0
+			>;
+	};
+};
+&soc {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	device_type = "soc";
+	compatible = "fsl,mpc8536-immr", "simple-bus";
+	bus-frequency = <0>;		// Filled out by uboot.
+
+	ecm-law@0 {
+		compatible = "fsl,ecm-law";
+		reg = <0x0 0x1000>;
+		fsl,num-laws = <12>;
+	};
+
+	ecm@1000 {
+		compatible = "fsl,mpc8536-ecm", "fsl,ecm";
+		reg = <0x1000 0x1000>;
+		interrupts = <17 2 0 0>;
+	};
+
+	memory-controller@2000 {
+		compatible = "fsl,mpc8536-memory-controller";
+		reg = <0x2000 0x1000>;
+		interrupts = <18 2 0 0>;
+	};
+
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+/include/ "pq3-duart-0.dtsi"
+
+/include/ "pq3-espi-0.dtsi"
+	spi@7000 {
+		fsl,espi-num-chipselects = <4>;
+	};
+
+/include/ "pq3-gpio-0.dtsi"
+
+	/* mark compat w/8572 to get some erratum treatment */
+	gpio-controller@f000 {
+		compatible = "fsl,mpc8572-gpio", "fsl,pq3-gpio";
+	};
+
+	sata@18000 {
+		compatible = "fsl,mpc8536-sata", "fsl,pq-sata";
+		reg = <0x18000 0x1000>;
+		cell-index = <1>;
+		interrupts = <74 0x2 0 0>;
+	};
+
+	sata@19000 {
+		compatible = "fsl,mpc8536-sata", "fsl,pq-sata";
+		reg = <0x19000 0x1000>;
+		cell-index = <2>;
+		interrupts = <41 0x2 0 0>;
+	};
+
+	L2: l2-cache-controller@20000 {
+		compatible = "fsl,mpc8536-l2-cache-controller";
+		reg = <0x20000 0x1000>;
+		cache-line-size = <32>;	// 32 bytes
+		cache-size = <0x80000>; // L2, 512K
+		interrupts = <16 2 0 0>;
+	};
+
+/include/ "pq3-dma-0.dtsi"
+/include/ "pq3-etsec1-0.dtsi"
+/include/ "pq3-etsec1-timer-0.dtsi"
+
+	usb@22000 {
+		compatible = "fsl,mpc8536-usb2-mph", "fsl-usb2-mph";
+		reg = <0x22000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts = <28 0x2 0 0>;
+	};
+
+	usb@23000 {
+		compatible = "fsl,mpc8536-usb2-mph", "fsl-usb2-mph";
+		reg = <0x23000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts = <46 0x2 0 0>;
+	};
+
+	ptp_clock@24e00 {
+		interrupts = <68 2 0 0 69 2 0 0 70 2 0 0 71 2 0 0>;
+	};
+
+/include/ "pq3-etsec1-2.dtsi"
+
+	ethernet@26000 {
+		cell-index = <1>;
+	};
+
+	usb@2b000 {
+		compatible = "fsl,mpc8536-usb2-dr", "fsl-usb2-dr";
+		reg = <0x2b000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts = <60 0x2 0 0>;
+	};
+
+/include/ "pq3-esdhc-0.dtsi"
+/include/ "pq3-sec3.0-0.dtsi"
+/include/ "pq3-mpic.dtsi"
+/include/ "pq3-mpic-timer-B.dtsi"
+
+	global-utilities@e0000 {
+		compatible = "fsl,mpc8536-guts";
+		reg = <0xe0000 0x1000>;
+		fsl,has-rstcr;
+	};
+};

arch/powerpc/boot/dts/fsl/mpc8536si-pre.dtsi

+/*
+ * MPC8536 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+	compatible = "fsl,MPC8536";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+		ethernet0 = &enet0;
+		ethernet1 = &enet2;
+		pci0 = &pci0;
+		pci1 = &pci1;
+		pci2 = &pci2;
+		pci3 = &pci3;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,8536@0 {
+			device_type = "cpu";
+			reg = <0x0>;
+			next-level-cache = <&L2>;
+		};
+	};
+};

arch/powerpc/boot/dts/fsl/mpc8544si-post.dtsi

+/*
+ * MPC8544 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	compatible = "fsl,mpc8544-lbc", "fsl,pq3-localbus", "simple-bus";
+	interrupts = <19 2 0 0>;
+};
+
+/* controller at 0x8000 */
+&pci0 {
+	compatible = "fsl,mpc8540-pci";
+	device_type = "pci";
+	interrupts = <24 0x2 0 0>;
+	bus-range = <0 0xff>;
+	#interrupt-cells = <1>;
+	#size-cells = <2>;
+	#address-cells = <3>;
+};
+
+/* controller at 0x9000 */
+&pci1 {
+	compatible = "fsl,mpc8548-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <25 2 0 0>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <25 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x4 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x5 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0x6 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0x7 0x1 0x0 0x0
+			>;
+	};
+};
+
+/* controller at 0xa000 */
+&pci2 {
+	compatible = "fsl,mpc8548-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <26 2 0 0>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <26 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x0 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x1 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0x2 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0x3 0x1 0x0 0x0
+			>;
+	};
+};
+
+/* controller at 0xb000 */
+&pci3 {
+	compatible = "fsl,mpc8548-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <27 2 0 0>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <27 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x8 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x9 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0xa 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0xb 0x1 0x0 0x0
+			>;
+	};
+};
+
+&soc {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	device_type = "soc";
+	compatible = "fsl,mpc8544-immr", "simple-bus";
+	bus-frequency = <0>;		// Filled out by uboot.
+
+	ecm-law@0 {
+		compatible = "fsl,ecm-law";
+		reg = <0x0 0x1000>;
+		fsl,num-laws = <10>;
+	};
+
+	ecm@1000 {
+		compatible = "fsl,mpc8544-ecm", "fsl,ecm";
+		reg = <0x1000 0x1000>;
+		interrupts = <17 2 0 0>;
+	};
+
+	memory-controller@2000 {
+		compatible = "fsl,mpc8544-memory-controller";
+		reg = <0x2000 0x1000>;
+		interrupts = <18 2 0 0>;
+	};
+
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+/include/ "pq3-duart-0.dtsi"
+
+	L2: l2-cache-controller@20000 {
+		compatible = "fsl,mpc8544-l2-cache-controller";
+		reg = <0x20000 0x1000>;
+		cache-line-size = <32>;	// 32 bytes
+		cache-size = <0x40000>; // L2, 256K
+		interrupts = <16 2 0 0>;
+	};
+
+/include/ "pq3-dma-0.dtsi"
+/include/ "pq3-etsec1-0.dtsi"
+/include/ "pq3-etsec1-2.dtsi"
+
+	ethernet@26000 {
+		cell-index = <1>;
+	};
+
+/include/ "pq3-sec2.1-0.dtsi"
+/include/ "pq3-mpic.dtsi"
+
+	global-utilities@e0000 {
+		compatible = "fsl,mpc8544-guts";
+		reg = <0xe0000 0x1000>;
+		fsl,has-rstcr;
+	};
+};

arch/powerpc/boot/dts/fsl/mpc8544si-pre.dtsi

+/*
+ * MPC8544 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+	compatible = "fsl,MPC8544";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+		ethernet0 = &enet0;
+		ethernet1 = &enet2;
+		pci0 = &pci0;
+		pci1 = &pci1;
+		pci2 = &pci2;
+		pci3 = &pci3;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,8544@0 {
+			device_type = "cpu";
+			reg = <0x0>;
+			next-level-cache = <&L2>;
+		};
+	};
+};

arch/powerpc/boot/dts/fsl/mpc8548si-post.dtsi

+/*
+ * MPC8548 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	compatible = "fsl,mpc8548-lbc", "fsl,pq3-localbus", "simple-bus";
+	interrupts = <19 2 0 0>;
+};
+
+/* controller at 0x8000 */
+&pci0 {
+	compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci";
+	device_type = "pci";
+	interrupts = <24 0x2 0 0>;
+	bus-range = <0 0xff>;
+	#interrupt-cells = <1>;
+	#size-cells = <2>;
+	#address-cells = <3>;
+};
+
+/* controller at 0x9000 */
+&pci1 {
+	compatible = "fsl,mpc8540-pci";
+	device_type = "pci";
+	interrupts = <25 0x2 0 0>;
+	bus-range = <0 0xff>;
+	#interrupt-cells = <1>;
+	#size-cells = <2>;
+	#address-cells = <3>;
+};
+
+/* controller at 0xa000 */
+&pci2 {
+	compatible = "fsl,mpc8548-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <26 2 0 0>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <26 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x0 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x1 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0x2 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0x3 0x1 0x0 0x0
+			>;
+	};
+};
+
+&soc {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	device_type = "soc";
+	compatible = "fsl,mpc8548-immr", "simple-bus";
+	bus-frequency = <0>;		// Filled out by uboot.
+
+	ecm-law@0 {
+		compatible = "fsl,ecm-law";
+		reg = <0x0 0x1000>;
+		fsl,num-laws = <10>;
+	};
+
+	ecm@1000 {
+		compatible = "fsl,mpc8548-ecm", "fsl,ecm";
+		reg = <0x1000 0x1000>;
+		interrupts = <17 2 0 0>;
+	};
+
+	memory-controller@2000 {
+		compatible = "fsl,mpc8548-memory-controller";
+		reg = <0x2000 0x1000>;
+		interrupts = <18 2 0 0>;
+	};
+
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+/include/ "pq3-duart-0.dtsi"
+
+	L2: l2-cache-controller@20000 {
+		compatible = "fsl,mpc8548-l2-cache-controller";
+		reg = <0x20000 0x1000>;
+		cache-line-size = <32>;	// 32 bytes
+		cache-size = <0x80000>; // L2, 512K
+		interrupts = <16 2 0 0>;
+	};
+
+/include/ "pq3-dma-0.dtsi"
+/include/ "pq3-etsec1-0.dtsi"
+/include/ "pq3-etsec1-1.dtsi"
+/include/ "pq3-etsec1-2.dtsi"
+/include/ "pq3-etsec1-3.dtsi"
+
+/include/ "pq3-sec2.1-0.dtsi"
+/include/ "pq3-mpic.dtsi"
+
+	global-utilities@e0000 {
+		compatible = "fsl,mpc8548-guts";
+		reg = <0xe0000 0x1000>;
+		fsl,has-rstcr;
+	};
+};

arch/powerpc/boot/dts/fsl/mpc8548si-pre.dtsi

+/*
+ * MPC8548 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+	compatible = "fsl,MPC8548";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+		ethernet0 = &enet0;
+		ethernet1 = &enet2;
+		pci0 = &pci0;
+		pci1 = &pci1;
+		pci2 = &pci2;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,8548@0 {
+			device_type = "cpu";
+			reg = <0x0>;
+			next-level-cache = <&L2>;
+		};
+	};
+};

arch/powerpc/boot/dts/fsl/mpc8568si-post.dtsi

+/*
+ * MPC8568 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	compatible = "fsl,mpc8568-localbus", "fsl,pq3-localbus", "simple-bus";
+	interrupts = <19 2 0 0>;
+	sleep = <&pmc 0x08000000>;
+};
+
+/* controller at 0x8000 */
+&pci0 {
+	compatible = "fsl,mpc8540-pci";
+	device_type = "pci";
+	interrupts = <24 0x2 0 0>;
+	bus-range = <0 0xff>;
+	#interrupt-cells = <1>;
+	#size-cells = <2>;
+	#address-cells = <3>;
+	sleep = <&pmc 0x80000000>;
+};
+
+/* controller at 0xa000 */
+&pci1 {
+	compatible = "fsl,mpc8548-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <26 2 0 0>;
+	sleep = <&pmc 0x20000000>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <26 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x0 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x1 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0x2 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0x3 0x1 0x0 0x0
+			>;
+	};
+};
+
+&rio {
+	compatible = "fsl,srio";
+	interrupts = <48 2 0 0>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+	fsl,srio-rmu-handle = <&rmu>;
+	sleep = <&pmc 0x00080000>;
+	ranges;
+
+	port1 {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		cell-index = <1>;
+	};
+};
+
+&soc {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	device_type = "soc";
+	compatible = "fsl,mpc8568-immr", "simple-bus";
+	bus-frequency = <0>;		// Filled out by uboot.
+
+	ecm-law@0 {
+		compatible = "fsl,ecm-law";
+		reg = <0x0 0x1000>;
+		fsl,num-laws = <10>;
+	};
+
+	ecm@1000 {
+		compatible = "fsl,mpc8568-ecm", "fsl,ecm";
+		reg = <0x1000 0x1000>;
+		interrupts = <17 2 0 0>;
+	};
+
+	memory-controller@2000 {
+		compatible = "fsl,mpc8568-memory-controller";
+		reg = <0x2000 0x1000>;
+		interrupts = <18 2 0 0>;
+	};
+
+	i2c-sleep-nexus {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		sleep = <&pmc 0x00000004>;
+		ranges;
+
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+
+	};
+
+	duart-sleep-nexus {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		sleep = <&pmc 0x00000002>;
+		ranges;
+
+/include/ "pq3-duart-0.dtsi"
+
+	};
+
+	L2: l2-cache-controller@20000 {
+		compatible = "fsl,mpc8568-l2-cache-controller";
+		reg = <0x20000 0x1000>;
+		cache-line-size = <32>;	// 32 bytes
+		cache-size = <0x80000>; // L2, 512K
+		interrupts = <16 2 0 0>;
+	};
+
+/include/ "pq3-dma-0.dtsi"
+	dma@21300 {
+		sleep = <&pmc 0x00000400>;
+	};
+
+/include/ "pq3-etsec1-0.dtsi"
+	ethernet@24000 {
+		sleep = <&pmc 0x00000080>;
+	};
+
+/include/ "pq3-etsec1-1.dtsi"
+	ethernet@25000 {
+		sleep = <&pmc 0x00000040>;
+	};
+
+	par_io@e0100 {
+		reg = <0xe0100 0x100>;
+		device_type = "par_io";
+	};
+
+/include/ "pq3-sec2.1-0.dtsi"
+	crypto@30000 {
+		sleep = <&pmc 0x01000000>;
+	};
+
+/include/ "pq3-mpic.dtsi"
+/include/ "pq3-rmu-0.dtsi"
+	rmu@d3000 {
+		sleep = <&pmc 0x00040000>;
+	};
+
+	global-utilities@e0000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "fsl,mpc8568-guts", "fsl,mpc8548-guts";
+		reg = <0xe0000 0x1000>;
+		ranges = <0 0xe0000 0x1000>;
+		fsl,has-rstcr;
+
+		pmc: power@70 {
+			compatible = "fsl,mpc8568-pmc",
+				     "fsl,mpc8548-pmc";
+			reg = <0x70 0x20>;
+		};
+	};
+};
+
+&qe {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	device_type = "qe";
+	compatible = "fsl,qe";
+	sleep = <&pmc 0x00000800>;
+	brg-frequency = <0>;
+	bus-frequency = <396000000>;
+	fsl,qe-num-riscs = <2>;
+	fsl,qe-num-snums = <28>;
+
+	qeic: interrupt-controller@80 {
+		interrupt-controller;
+		compatible = "fsl,qe-ic";
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		reg = <0x80 0x80>;
+		interrupts = <46 2 0 0 46 2 0 0>; //high:30 low:30
+		interrupt-parent = <&mpic>;
+	};
+
+	spi@4c0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,spi";
+		reg = <0x4c0 0x40>;
+		cell-index = <0>;
+		interrupts = <2>;
+		interrupt-parent = <&qeic>;
+	};
+
+	spi@500 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cell-index = <1>;
+		compatible = "fsl,spi";
+		reg = <0x500 0x40>;
+		interrupts = <1>;
+		interrupt-parent = <&qeic>;
+	};
+
+	ucc@2000 {
+		cell-index = <1>;
+		reg = <0x2000 0x200>;
+		interrupts = <32>;
+		interrupt-parent = <&qeic>;
+	};
+
+	ucc@3000 {
+		cell-index = <2>;
+		reg = <0x3000 0x200>;
+		interrupts = <33>;
+		interrupt-parent = <&qeic>;
+	};
+
+	muram@10000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "fsl,qe-muram", "fsl,cpm-muram";
+		ranges = <0x0 0x10000 0x10000>;
+
+		data-only@0 {
+			compatible = "fsl,qe-muram-data",
+				     "fsl,cpm-muram-data";
+			reg = <0x0 0x10000>;
+		};
+	};
+};

arch/powerpc/boot/dts/fsl/mpc8568si-pre.dtsi

+/*
+ * MPC8568 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+	compatible = "fsl,MPC8568";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+		ethernet0 = &enet0;
+		ethernet1 = &enet1;
+		ethernet2 = &enet2;
+		ethernet3 = &enet3;
+		pci0 = &pci0;
+		pci1 = &pci1;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,8568@0 {
+			device_type = "cpu";
+			reg = <0x0>;
+			next-level-cache = <&L2>;
+			sleep = <&pmc 0x00008000	// core
+				 &pmc 0x00004000>;	// timebase
+		};
+	};
+};

arch/powerpc/boot/dts/fsl/mpc8569si-post.dtsi

+/*
+ * MPC8569 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	compatible = "fsl,mpc8569-elbc", "fsl,elbc", "simple-bus";
+	interrupts = <19 2 0 0>;
+	sleep = <&pmc 0x08000000>;
+};
+
+/* controller at 0xa000 */
+&pci1 {
+	compatible = "fsl,mpc8548-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <26 2 0 0>;
+	sleep = <&pmc 0x20000000>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <26 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x0 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x1 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0x2 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0x3 0x1 0x0 0x0
+			>;
+	};
+};
+
+&rio {
+	compatible = "fsl,srio";
+	interrupts = <48 2 0 0>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+	fsl,srio-rmu-handle = <&rmu>;
+	sleep = <&pmc 0x00080000>;
+	ranges;
+
+	port1 {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		cell-index = <1>;
+	};
+
+	port2 {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		cell-index = <2>;
+	};
+};
+
+&soc {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	device_type = "soc";
+	compatible = "fsl,mpc8569-immr", "simple-bus";
+	bus-frequency = <0>;		// Filled out by uboot.
+
+	ecm-law@0 {
+		compatible = "fsl,ecm-law";
+		reg = <0x0 0x1000>;
+		fsl,num-laws = <10>;
+	};
+
+	ecm@1000 {
+		compatible = "fsl,mpc8569-ecm", "fsl,ecm";
+		reg = <0x1000 0x1000>;
+		interrupts = <17 2 0 0>;
+	};
+
+	memory-controller@2000 {
+		compatible = "fsl,mpc8569-memory-controller";
+		reg = <0x2000 0x1000>;
+		interrupts = <18 2 0 0>;
+	};
+
+	i2c-sleep-nexus {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		sleep = <&pmc 0x00000004>;
+		ranges;
+
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+
+	};
+
+	duart-sleep-nexus {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		sleep = <&pmc 0x00000002>;
+		ranges;
+
+/include/ "pq3-duart-0.dtsi"
+
+	};
+
+	L2: l2-cache-controller@20000 {
+		compatible = "fsl,mpc8569-l2-cache-controller";
+		reg = <0x20000 0x1000>;
+		cache-line-size = <32>;	// 32 bytes
+		cache-size = <0x80000>; // L2, 512K
+		interrupts = <16 2 0 0>;
+	};
+
+/include/ "pq3-dma-0.dtsi"
+/include/ "pq3-esdhc-0.dtsi"
+	sdhc@2e000 {
+		sleep = <&pmc 0x00200000>;
+	};
+
+	par_io@e0100 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0xe0100 0x100>;
+		ranges = <0x0 0xe0100 0x100>;
+		device_type = "par_io";
+	};
+
+/include/ "pq3-sec3.1-0.dtsi"
+	crypto@30000 {
+		sleep = <&pmc 0x01000000>;
+	};
+
+/include/ "pq3-mpic.dtsi"
+/include/ "pq3-rmu-0.dtsi"
+	rmu@d3000 {
+		sleep = <&pmc 0x00040000>;
+	};
+
+	global-utilities@e0000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "fsl,mpc8569-guts", "fsl,mpc8548-guts";
+		reg = <0xe0000 0x1000>;
+		ranges = <0 0xe0000 0x1000>;
+		fsl,has-rstcr;
+
+		pmc: power@70 {
+			compatible = "fsl,mpc8569-pmc",
+				     "fsl,mpc8548-pmc";
+			reg = <0x70 0x20>;
+		};
+	};
+};
+
+&qe {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	device_type = "qe";
+	compatible = "fsl,qe";
+	sleep = <&pmc 0x00000800>;
+	brg-frequency = <0>;
+	bus-frequency = <0>;
+	fsl,qe-num-riscs = <4>;
+	fsl,qe-num-snums = <46>;
+
+	qeic: interrupt-controller@80 {
+		interrupt-controller;
+		compatible = "fsl,qe-ic";
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		reg = <0x80 0x80>;
+		interrupts = <46 2 0 0 46 2 0 0>; //high:30 low:30
+		interrupt-parent = <&mpic>;
+	};
+
+	timer@440 {
+		compatible = "fsl,mpc8569-qe-gtm",
+			     "fsl,qe-gtm", "fsl,gtm";
+		reg = <0x440 0x40>;
+		interrupts = <12 13 14 15>;
+		interrupt-parent = <&qeic>;
+		/* Filled in by U-Boot */
+		clock-frequency = <0>;
+	};
+
+	spi@4c0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,mpc8569-qe-spi", "fsl,spi";
+		reg = <0x4c0 0x40>;
+		cell-index = <0>;
+		interrupts = <2>;
+		interrupt-parent = <&qeic>;
+	};
+
+	spi@500 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cell-index = <1>;
+		compatible = "fsl,spi";
+		reg = <0x500 0x40>;
+		interrupts = <1>;
+		interrupt-parent = <&qeic>;
+	};
+
+	usb@6c0 {
+		compatible = "fsl,mpc8569-qe-usb",
+			     "fsl,mpc8323-qe-usb";
+		reg = <0x6c0 0x40 0x8b00 0x100>;
+		interrupts = <11>;
+		interrupt-parent = <&qeic>;
+	};
+
+	ucc@2000 {
+		cell-index = <1>;
+		reg = <0x2000 0x200>;
+		interrupts = <32>;
+		interrupt-parent = <&qeic>;
+	};
+
+	ucc@2200 {
+		cell-index = <3>;
+		reg = <0x2200 0x200>;
+		interrupts = <34>;
+		interrupt-parent = <&qeic>;
+	};
+
+	ucc@3000 {
+		cell-index = <2>;
+		reg = <0x3000 0x200>;
+		interrupts = <33>;
+		interrupt-parent = <&qeic>;
+	};
+
+	ucc@3200 {
+		cell-index = <4>;
+		reg = <0x3200 0x200>;
+		interrupts = <35>;
+		interrupt-parent = <&qeic>;
+	};
+
+	ucc@3400 {
+		cell-index = <6>;
+		reg = <0x3400 0x200>;
+		interrupts = <41>;
+		interrupt-parent = <&qeic>;
+	};
+
+	ucc@3600 {
+		cell-index = <8>;
+		reg = <0x3600 0x200>;
+		interrupts = <43>;
+		interrupt-parent = <&qeic>;
+	};
+
+	muram@10000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "fsl,qe-muram", "fsl,cpm-muram";
+		ranges = <0x0 0x10000 0x20000>;
+
+		data-only@0 {
+			compatible = "fsl,qe-muram-data",
+				     "fsl,cpm-muram-data";
+			reg = <0x0 0x20000>;
+		};
+	};
+};

arch/powerpc/boot/dts/fsl/mpc8569si-pre.dtsi

+/*
+ * MPC8569 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+	compatible = "fsl,MPC8569";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+		ethernet0 = &enet0;
+		ethernet1 = &enet1;
+		ethernet2 = &enet2;
+		ethernet3 = &enet3;
+		pci1 = &pci1;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,8569@0 {
+			device_type = "cpu";
+			reg = <0x0>;
+			next-level-cache = <&L2>;
+			sleep = <&pmc 0x00008000	// core
+				 &pmc 0x00004000>;	// timebase
+		};
+	};
+};

arch/powerpc/boot/dts/fsl/mpc8572si-post.dtsi

+/*
+ * MPC8572 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	compatible = "fsl,mpc8572-elbc", "fsl,elbc", "simple-bus";
+	interrupts = <19 2 0 0>;
+};
+
+/* controller at 0x8000 */
+&pci0 {
+	compatible = "fsl,mpc8548-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <24 2 0 0>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <24 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x8 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x9 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0xa 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0xb 0x1 0x0 0x0
+			>;
+	};
+};
+
+/* controller at 0x9000 */
+&pci1 {
+	compatible = "fsl,mpc8548-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <25 2 0 0>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <25 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x4 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x5 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0x6 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0x7 0x1 0x0 0x0
+			>;
+	};
+};
+
+/* controller at 0xa000 */
+&pci2 {
+	compatible = "fsl,mpc8548-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <26 2 0 0>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <26 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x0 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x1 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0x2 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0x3 0x1 0x0 0x0
+			>;
+	};
+};
+
+&soc {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	device_type = "soc";
+	compatible = "fsl,mpc8572-immr", "simple-bus";
+	bus-frequency = <0>;		// Filled out by uboot.
+
+	ecm-law@0 {
+		compatible = "fsl,ecm-law";
+		reg = <0x0 0x1000>;
+		fsl,num-laws = <12>;
+	};
+
+	ecm@1000 {
+		compatible = "fsl,mpc8572-ecm", "fsl,ecm";
+		reg = <0x1000 0x1000>;
+		interrupts = <17 2 0 0>;
+	};
+
+	memory-controller@2000 {
+		compatible = "fsl,mpc8572-memory-controller";
+		reg = <0x2000 0x1000>;
+		interrupts = <18 2 0 0>;
+	};
+
+	memory-controller@6000 {
+		compatible = "fsl,mpc8572-memory-controller";
+		reg = <0x6000 0x1000>;
+		interrupts = <18 2 0 0>;
+	};
+
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+/include/ "pq3-duart-0.dtsi"
+/include/ "pq3-dma-1.dtsi"
+/include/ "pq3-gpio-0.dtsi"
+	gpio-controller@f000 {
+		compatible = "fsl,mpc8572-gpio", "fsl,pq3-gpio";
+	};
+
+	L2: l2-cache-controller@20000 {
+		compatible = "fsl,mpc8572-l2-cache-controller";
+		reg = <0x20000 0x1000>;
+		cache-line-size = <32>;	// 32 bytes
+		cache-size = <0x100000>; // L2,1M
+		interrupts = <16 2 0 0>;
+	};
+
+/include/ "pq3-dma-0.dtsi"
+/include/ "pq3-etsec1-0.dtsi"
+/include/ "pq3-etsec1-timer-0.dtsi"
+
+	ptp_clock@24e00 {
+		interrupts = <68 2 0 0 69 2 0 0 70 2 0 0 71 2 0 0>;
+	};
+
+/include/ "pq3-etsec1-1.dtsi"
+/include/ "pq3-etsec1-2.dtsi"
+/include/ "pq3-etsec1-3.dtsi"
+/include/ "pq3-sec3.0-0.dtsi"
+/include/ "pq3-mpic.dtsi"
+/include/ "pq3-mpic-timer-B.dtsi"
+
+	global-utilities@e0000 {
+		compatible = "fsl,mpc8572-guts";
+		reg = <0xe0000 0x1000>;
+		fsl,has-rstcr;
+	};
+};

arch/powerpc/boot/dts/fsl/mpc8572si-pre.dtsi

+/*
+ * MPC8572 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+	compatible = "fsl,MPC8572";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+		ethernet0 = &enet0;
+		ethernet1 = &enet1;
+		ethernet2 = &enet2;
+		ethernet3 = &enet3;
+		pci0 = &pci0;
+		pci1 = &pci1;
+		pci2 = &pci2;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,8572@0 {
+			device_type = "cpu";
+			reg = <0x0>;
+			next-level-cache = <&L2>;
+		};
+
+		PowerPC,8572@1 {
+			device_type = "cpu";
+			reg = <0x1>;
+			next-level-cache = <&L2>;
+		};
+	};
+};

arch/powerpc/boot/dts/fsl/p1010si-post.dtsi

+/*
+ * P1010/P1014 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&ifc {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	compatible = "fsl,ifc", "simple-bus";
+	interrupts = <16 2 0 0 19 2 0 0>;
+};
+
+/* controller at 0x9000 */
+&pci0 {
+	compatible = "fsl,p1010-pcie", "fsl,qoriq-pcie-v2.3", "fsl,qoriq-pcie-v2.2";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <16 2 0 0>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <16 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x4 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x5 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0x6 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0x7 0x1 0x0 0x0
+			>;
+	};
+};
+
+/* controller at 0xa000 */
+&pci1 {
+	compatible = "fsl,p1010-pcie", "fsl,qoriq-pcie-v2.3", "fsl,qoriq-pcie-v2.2";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <16 2 0 0>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <16 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x0 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x1 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0x2 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0x3 0x1 0x0 0x0
+			>;
+	};
+};
+
+&soc {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	device_type = "soc";
+	compatible = "fsl,p1010-immr", "simple-bus";
+	bus-frequency = <0>;		// Filled out by uboot.
+
+	ecm-law@0 {
+		compatible = "fsl,ecm-law";
+		reg = <0x0 0x1000>;
+		fsl,num-laws = <12>;
+	};
+
+	ecm@1000 {
+		compatible = "fsl,p1010-ecm", "fsl,ecm";
+		reg = <0x1000 0x1000>;
+		interrupts = <16 2 0 0>;
+	};
+
+	memory-controller@2000 {
+		compatible = "fsl,p1010-memory-controller";
+		reg = <0x2000 0x1000>;
+		interrupts = <16 2 0 0>;
+	};
+
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+/include/ "pq3-duart-0.dtsi"
+/include/ "pq3-espi-0.dtsi"
+	spi0: spi@7000 {
+		fsl,espi-num-chipselects = <1>;
+	};
+
+/include/ "pq3-gpio-0.dtsi"
+/include/ "pq3-sata2-0.dtsi"
+/include/ "pq3-sata2-1.dtsi"
+
+	can0: can@1c000 {
+		compatible = "fsl,p1010-flexcan";
+		reg = <0x1c000 0x1000>;
+		interrupts = <48 0x2 0 0>;
+	};
+
+	can1: can@1d000 {
+		compatible = "fsl,p1010-flexcan";
+		reg = <0x1d000 0x1000>;
+		interrupts = <61 0x2 0 0>;
+	};
+
+	L2: l2-cache-controller@20000 {
+		compatible = "fsl,p1010-l2-cache-controller",
+				"fsl,p1014-l2-cache-controller";
+		reg = <0x20000 0x1000>;
+		cache-line-size = <32>;	// 32 bytes
+		cache-size = <0x40000>; // L2,256K
+		interrupts = <16 2 0 0>;
+	};
+
+/include/ "pq3-dma-0.dtsi"
+/include/ "pq3-usb2-dr-0.dtsi"
+/include/ "pq3-esdhc-0.dtsi"
+	sdhc@2e000 {
+		fsl,sdhci-auto-cmd12;
+	};
+
+/include/ "pq3-sec4.4-0.dtsi"
+/include/ "pq3-mpic.dtsi"
+/include/ "pq3-mpic-timer-B.dtsi"
+
+/include/ "pq3-etsec2-0.dtsi"
+	enet0: ethernet@b0000 {
+		queue-group@b0000 {
+			fsl,rx-bit-map = <0xff>;
+			fsl,tx-bit-map = <0xff>;
+		};
+	};
+
+/include/ "pq3-etsec2-1.dtsi"
+	enet1: ethernet@b1000 {
+		queue-group@b1000 {
+			fsl,rx-bit-map = <0xff>;
+			fsl,tx-bit-map = <0xff>;
+		};
+	};
+
+/include/ "pq3-etsec2-2.dtsi"
+	enet2: ethernet@b2000 {
+		queue-group@b2000 {
+			fsl,rx-bit-map = <0xff>;
+			fsl,tx-bit-map = <0xff>;
+		};
+
+	};
+
+	global-utilities@e0000 {
+		compatible = "fsl,p1010-guts";
+		reg = <0xe0000 0x1000>;
+		fsl,has-rstcr;
+	};
+};

arch/powerpc/boot/dts/fsl/p1010si-pre.dtsi

+/*
+ * P1010/P1014 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+	compatible = "fsl,P1010";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+		ethernet0 = &enet0;
+		ethernet1 = &enet1;
+		ethernet2 = &enet2;
+		pci0 = &pci0;
+		pci1 = &pci1;
+		can0 = &can0;
+		can1 = &can1;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,P1010@0 {
+			device_type = "cpu";
+			reg = <0x0>;
+			next-level-cache = <&L2>;
+		};
+	};
+};

arch/powerpc/boot/dts/fsl/p1020si-post.dtsi

+/*
+ * P1020/P1011 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	compatible = "fsl,p1020-elbc", "fsl,elbc", "simple-bus";
+	interrupts = <19 2 0 0>;
+};
+
+/* controller at 0x9000 */
+&pci0 {
+	compatible = "fsl,mpc8548-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <16 2 0 0>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <16 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x4 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x5 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0x6 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0x7 0x1 0x0 0x0
+			>;
+	};
+};
+
+/* controller at 0xa000 */
+&pci1 {
+	compatible = "fsl,mpc8548-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <16 2 0 0>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <16 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x0 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x1 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0x2 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0x3 0x1 0x0 0x0
+			>;
+	};
+};
+
+&soc {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	device_type = "soc";
+	compatible = "fsl,p1020-immr", "simple-bus";
+	bus-frequency = <0>;		// Filled out by uboot.
+
+	ecm-law@0 {
+		compatible = "fsl,ecm-law";
+		reg = <0x0 0x1000>;
+		fsl,num-laws = <12>;
+	};
+
+	ecm@1000 {
+		compatible = "fsl,p1020-ecm", "fsl,ecm";
+		reg = <0x1000 0x1000>;
+		interrupts = <16 2 0 0>;
+	};
+
+	memory-controller@2000 {
+		compatible = "fsl,p1020-memory-controller";
+		reg = <0x2000 0x1000>;
+		interrupts = <16 2 0 0>;
+	};
+
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+/include/ "pq3-duart-0.dtsi"
+
+/include/ "pq3-espi-0.dtsi"
+	spi@7000 {
+		fsl,espi-num-chipselects = <4>;
+	};
+
+/include/ "pq3-gpio-0.dtsi"
+
+	L2: l2-cache-controller@20000 {
+		compatible = "fsl,p1020-l2-cache-controller";
+		reg = <0x20000 0x1000>;
+		cache-line-size = <32>;	// 32 bytes
+		cache-size = <0x40000>; // L2,256K
+		interrupts = <16 2 0 0>;
+	};
+
+/include/ "pq3-dma-0.dtsi"
+/include/ "pq3-usb2-dr-0.dtsi"
+/include/ "pq3-usb2-dr-1.dtsi"
+
+/include/ "pq3-esdhc-0.dtsi"
+/include/ "pq3-sec3.3-0.dtsi"
+
+/include/ "pq3-mpic.dtsi"
+/include/ "pq3-mpic-timer-B.dtsi"
+
+/include/ "pq3-etsec2-0.dtsi"
+	enet0: enet0_grp2: ethernet@b0000 {
+	};
+
+/include/ "pq3-etsec2-1.dtsi"
+	enet1: enet1_grp2: ethernet@b1000 {
+	};
+
+/include/ "pq3-etsec2-2.dtsi"
+	enet2: enet2_grp2: ethernet@b2000 {
+	};
+
+	global-utilities@e0000 {
+		compatible = "fsl,p1020-guts";
+		reg = <0xe0000 0x1000>;
+		fsl,has-rstcr;
+	};
+};
+
+/include/ "pq3-etsec2-grp2-0.dtsi"
+/include/ "pq3-etsec2-grp2-1.dtsi"
+/include/ "pq3-etsec2-grp2-2.dtsi"

arch/powerpc/boot/dts/fsl/p1020si-pre.dtsi

+/*
+ * P1020/P1011 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+	compatible = "fsl,P1020";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+		ethernet0 = &enet0;
+		ethernet1 = &enet1;
+		ethernet2 = &enet2;
+		pci0 = &pci0;
+		pci1 = &pci1;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,P1020@0 {
+			device_type = "cpu";
+			reg = <0x0>;
+			next-level-cache = <&L2>;
+		};
+
+		PowerPC,P1020@1 {
+			device_type = "cpu";
+			reg = <0x1>;
+			next-level-cache = <&L2>;
+		};
+	};
+};

arch/powerpc/boot/dts/fsl/p1021si-post.dtsi

+/*
+ * P1021/P1012 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	compatible = "fsl,p1021-elbc", "fsl,elbc", "simple-bus";
+	interrupts = <19 2 0 0>;
+};
+
+/* controller at 0x9000 */
+&pci0 {
+	compatible = "fsl,mpc8548-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <16 2 0 0>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <16 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x4 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x5 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0x6 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0x7 0x1 0x0 0x0
+			>;
+	};
+};
+
+/* controller at 0xa000 */
+&pci1 {
+	compatible = "fsl,mpc8548-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <16 2 0 0>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <16 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x0 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x1 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0x2 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0x3 0x1 0x0 0x0
+			>;
+	};
+};
+
+&soc {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	device_type = "soc";
+	compatible = "fsl,p1021-immr", "simple-bus";
+	bus-frequency = <0>;		// Filled out by uboot.
+
+	ecm-law@0 {
+		compatible = "fsl,ecm-law";
+		reg = <0x0 0x1000>;
+		fsl,num-laws = <12>;
+	};
+
+	ecm@1000 {
+		compatible = "fsl,p1021-ecm", "fsl,ecm";
+		reg = <0x1000 0x1000>;
+		interrupts = <16 2 0 0>;
+	};
+
+	memory-controller@2000 {
+		compatible = "fsl,p1021-memory-controller";
+		reg = <0x2000 0x1000>;
+		interrupts = <16 2 0 0>;
+	};
+
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+/include/ "pq3-duart-0.dtsi"
+
+/include/ "pq3-espi-0.dtsi"
+	spi@7000 {
+		fsl,espi-num-chipselects = <4>;
+	};
+
+/include/ "pq3-gpio-0.dtsi"
+
+	L2: l2-cache-controller@20000 {
+		compatible = "fsl,p1021-l2-cache-controller";
+		reg = <0x20000 0x1000>;
+		cache-line-size = <32>;	// 32 bytes
+		cache-size = <0x40000>; // L2,256K
+		interrupts = <16 2 0 0>;
+	};
+
+/include/ "pq3-dma-0.dtsi"
+/include/ "pq3-usb2-dr-0.dtsi"
+
+/include/ "pq3-esdhc-0.dtsi"
+/include/ "pq3-sec3.3-0.dtsi"
+
+/include/ "pq3-mpic.dtsi"
+/include/ "pq3-mpic-timer-B.dtsi"
+
+/include/ "pq3-etsec2-0.dtsi"
+	enet0: enet0_grp2: ethernet@b0000 {
+	};
+
+/include/ "pq3-etsec2-1.dtsi"
+	enet1: enet1_grp2: ethernet@b1000 {
+	};
+
+/include/ "pq3-etsec2-2.dtsi"
+	enet2: enet2_grp2: ethernet@b2000 {
+	};
+
+	global-utilities@e0000 {
+		compatible = "fsl,p1021-guts";
+		reg = <0xe0000 0x1000>;
+		fsl,has-rstcr;
+	};
+};
+
+&qe {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	device_type = "qe";
+	compatible = "fsl,qe";
+	fsl,qe-num-riscs = <1>;
+	fsl,qe-num-snums = <28>;
+
+	qeic: interrupt-controller@80 {
+		interrupt-controller;
+		compatible = "fsl,qe-ic";
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		reg = <0x80 0x80>;
+		interrupts = <63 2 0 0 60 2 0 0>; //high:47 low:44
+	};
+
+	ucc@2000 {
+		cell-index = <1>;
+		reg = <0x2000 0x200>;
+		interrupts = <32>;
+		interrupt-parent = <&qeic>;
+	};
+
+	mdio@2120 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x2120 0x18>;
+		compatible = "fsl,ucc-mdio";
+	};
+
+	ucc@2400 {
+		cell-index = <5>;
+		reg = <0x2400 0x200>;
+		interrupts = <40>;
+		interrupt-parent = <&qeic>;
+	};
+
+	muram@10000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "fsl,qe-muram", "fsl,cpm-muram";
+		ranges = <0x0 0x10000 0x6000>;
+
+		data-only@0 {
+			compatible = "fsl,qe-muram-data",
+			"fsl,cpm-muram-data";
+			reg = <0x0 0x6000>;
+		};
+	};
+};
+
+/include/ "pq3-etsec2-grp2-0.dtsi"
+/include/ "pq3-etsec2-grp2-1.dtsi"
+/include/ "pq3-etsec2-grp2-2.dtsi"

arch/powerpc/boot/dts/fsl/p1021si-pre.dtsi

+/*
+ * P1021/P1012 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+	compatible = "fsl,P1021";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+		ethernet0 = &enet0;
+		ethernet1 = &enet1;
+		ethernet2 = &enet2;
+		pci0 = &pci0;
+		pci1 = &pci1;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,P1021@0 {
+			device_type = "cpu";
+			reg = <0x0>;
+			next-level-cache = <&L2>;
+		};
+
+		PowerPC,P1021@1 {
+			device_type = "cpu";
+			reg = <0x1>;
+			next-level-cache = <&L2>;
+		};
+	};
+};

arch/powerpc/boot/dts/fsl/p1022si-post.dtsi

+/*
+ * P1022/P1013 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	compatible = "fsl,p1022-elbc", "fsl,elbc", "simple-bus";
+	interrupts = <19 2 0 0>;
+};
+
+/* controller at 0x9000 */
+&pci0 {
+	compatible = "fsl,p1022-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <16 2 0 0>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <16 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x4 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x5 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0x6 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0x7 0x1 0x0 0x0
+			>;
+	};
+};
+
+/* controller at 0xa000 */
+&pci1 {
+	compatible = "fsl,p1022-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <16 2 0 0>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <16 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x0 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x1 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0x2 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0x3 0x1 0x0 0x0
+			>;
+	};
+};
+
+/* controller at 0xb000 */
+&pci2 {
+	compatible = "fsl,p1022-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <16 2 0 0>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <16 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x8 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x9 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0xa 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0xb 0x1 0x0 0x0
+			>;
+	};
+};
+
+&soc {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	device_type = "soc";
+	compatible = "fsl,p1022-immr", "simple-bus";
+	bus-frequency = <0>;		// Filled out by uboot.
+
+	ecm-law@0 {
+		compatible = "fsl,ecm-law";
+		reg = <0x0 0x1000>;
+		fsl,num-laws = <12>;
+	};
+
+	ecm@1000 {
+		compatible = "fsl,p1022-ecm", "fsl,ecm";
+		reg = <0x1000 0x1000>;
+		interrupts = <16 2 0 0>;
+	};
+
+	memory-controller@2000 {
+		compatible = "fsl,p1022-memory-controller";
+		reg = <0x2000 0x1000>;
+		interrupts = <16 2 0 0>;
+	};
+
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+/include/ "pq3-duart-0.dtsi"
+/include/ "pq3-espi-0.dtsi"
+	spi@7000 {
+		fsl,espi-num-chipselects = <4>;
+	};
+
+/include/ "pq3-dma-1.dtsi"
+	dma@c300 {
+		dma00: dma-channel@0 {
+			compatible = "fsl,ssi-dma-channel";
+		};
+		dma01: dma-channel@80 {
+			compatible = "fsl,ssi-dma-channel";
+		};
+	};
+
+/include/ "pq3-gpio-0.dtsi"
+
+	display@10000 {
+		compatible = "fsl,diu", "fsl,p1022-diu";
+		reg = <0x10000 1000>;
+		interrupts = <64 2 0 0>;
+	};
+
+	ssi@15000 {
+		compatible = "fsl,mpc8610-ssi";
+		cell-index = <0>;
+		reg = <0x15000 0x100>;
+		interrupts = <75 2 0 0>;
+		fsl,playback-dma = <&dma00>;
+		fsl,capture-dma = <&dma01>;
+		fsl,fifo-depth = <15>;
+	};
+
+/include/ "pq3-sata2-0.dtsi"
+/include/ "pq3-sata2-1.dtsi"
+
+	L2: l2-cache-controller@20000 {
+		compatible = "fsl,p1022-l2-cache-controller";
+		reg = <0x20000 0x1000>;
+		cache-line-size = <32>;	// 32 bytes
+		cache-size = <0x40000>; // L2,256K
+		interrupts = <16 2 0 0>;
+	};
+
+/include/ "pq3-dma-0.dtsi"
+/include/ "pq3-usb2-dr-0.dtsi"
+/include/ "pq3-usb2-dr-1.dtsi"
+
+/include/ "pq3-esdhc-0.dtsi"
+	sdhc@2e000 {
+		fsl,sdhci-auto-cmd12;
+	};
+
+/include/ "pq3-sec3.3-0.dtsi"
+/include/ "pq3-mpic.dtsi"
+/include/ "pq3-mpic-timer-B.dtsi"
+
+/include/ "pq3-etsec2-0.dtsi"
+	enet0: enet0_grp2: ethernet@b0000 {
+	};
+
+/include/ "pq3-etsec2-1.dtsi"
+	enet1: enet1_grp2: ethernet@b1000 {
+	};
+
+	global-utilities@e0000 {
+		compatible = "fsl,p1022-guts";
+		reg = <0xe0000 0x1000>;
+		fsl,has-rstcr;
+	};
+
+	power@e0070{
+		compatible = "fsl,mpc8536-pmc", "fsl,mpc8548-pmc";
+		reg = <0xe0070 0x20>;
+	};
+
+};
+
+/include/ "pq3-etsec2-grp2-0.dtsi"
+/include/ "pq3-etsec2-grp2-1.dtsi"

arch/powerpc/boot/dts/fsl/p1022si-pre.dtsi

+/*
+ * P1022/P1013 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+	compatible = "fsl,P1022";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+		ethernet0 = &enet0;
+		ethernet1 = &enet1;
+		pci0 = &pci0;
+		pci1 = &pci1;
+		pci2 = &pci2;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,P1022@0 {
+			device_type = "cpu";
+			reg = <0x0>;
+			next-level-cache = <&L2>;
+		};
+
+		PowerPC,P1022@1 {
+			device_type = "cpu";
+			reg = <0x1>;
+			next-level-cache = <&L2>;
+		};
+	};
+};

arch/powerpc/boot/dts/fsl/p1023si-post.dtsi

+/*
+ * P1023/P1017 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	compatible = "fsl,p1023-elbc", "fsl,elbc", "simple-bus";
+	interrupts = <19 2 0 0>;
+};
+
+/* controller at 0xa000 */
+&pci0 {
+	compatible = "fsl,p1023-pcie", "fsl,qoriq-pcie-v2.2";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0x0 0xff>;
+	clock-frequency = <33333333>;
+	interrupts = <16 2 0 0>;
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <16 2 0 0>;
+	};
+};
+
+/* controller at 0x9000 */
+&pci1 {
+	compatible = "fsl,p1023-pcie", "fsl,qoriq-pcie-v2.2";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 0xff>;
+	clock-frequency = <33333333>;
+	interrupts = <16 2 0 0>;
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <16 2 0 0>;
+	};
+};
+
+/* controller at 0xb000 */
+&pci2 {
+	compatible = "fsl,p1023-pcie", "fsl,qoriq-pcie-v2.2";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0x0 0xff>;
+	clock-frequency = <33333333>;
+	interrupts = <16 2 0 0>;
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <16 2 0 0>;
+	};
+};
+
+&soc {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	device_type = "soc";
+	compatible = "fsl,p1023-immr", "simple-bus";
+	bus-frequency = <0>;		// Filled out by uboot.
+
+	ecm-law@0 {
+		compatible = "fsl,ecm-law";
+		reg = <0x0 0x1000>;
+		fsl,num-laws = <12>;
+	};
+
+	ecm@1000 {
+		compatible = "fsl,p1023-ecm", "fsl,ecm";
+		reg = <0x1000 0x1000>;
+		interrupts = <16 2 0 0>;
+	};
+
+	memory-controller@2000 {
+		compatible = "fsl,p1023-memory-controller";
+		reg = <0x2000 0x1000>;
+		interrupts = <16 2 0 0>;
+	};
+
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+/include/ "pq3-duart-0.dtsi"
+
+/include/ "pq3-espi-0.dtsi"
+	spi@7000 {
+		fsl,espi-num-chipselects = <4>;
+	};
+
+/include/ "pq3-gpio-0.dtsi"
+
+	L2: l2-cache-controller@20000 {
+		compatible = "fsl,p1023-l2-cache-controller";
+		reg = <0x20000 0x1000>;
+		cache-line-size = <32>;	// 32 bytes
+		cache-size = <0x40000>; // L2,256K
+		interrupts = <16 2 0 0>;
+	};
+
+/include/ "pq3-dma-0.dtsi"
+/include/ "pq3-usb2-dr-0.dtsi"
+
+	crypto: crypto@300000 {
+		compatible = "fsl,sec-v4.2", "fsl,sec-v4.0";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x30000 0x10000>;
+		ranges = <0 0x30000 0x10000>;
+		interrupts = <58 2 0 0>;
+
+		sec_jr0: jr@1000 {
+			compatible = "fsl,sec-v4.2-job-ring",
+				     "fsl,sec-v4.0-job-ring";
+			reg = <0x1000 0x1000>;
+			interrupts = <45 2 0 0>;
+		};
+
+		sec_jr1: jr@2000 {
+			compatible = "fsl,sec-v4.2-job-ring",
+				     "fsl,sec-v4.0-job-ring";
+			reg = <0x2000 0x1000>;
+			interrupts = <45 2 0 0>;
+		};
+
+		sec_jr2: jr@3000 {
+			compatible = "fsl,sec-v4.2-job-ring",
+				     "fsl,sec-v4.0-job-ring";
+			reg = <0x3000 0x1000>;
+			interrupts = <57 2 0 0>;
+		};
+
+		sec_jr3: jr@4000 {
+			compatible = "fsl,sec-v4.2-job-ring",
+				     "fsl,sec-v4.0-job-ring";
+			reg = <0x4000 0x1000>;
+			interrupts = <57 2 0 0>;
+		};
+
+		rtic@6000 {
+			compatible = "fsl,sec-v4.2-rtic",
+				     "fsl,sec-v4.0-rtic";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x6000 0x100>;
+			ranges = <0x0 0x6100 0xe00>;
+
+			rtic_a: rtic-a@0 {
+				compatible = "fsl,sec-v4.2-rtic-memory",
+					     "fsl,sec-v4.0-rtic-memory";
+				reg = <0x00 0x20 0x100 0x80>;
+			};
+
+			rtic_b: rtic-b@20 {
+				compatible = "fsl,sec-v4.2-rtic-memory",
+					     "fsl,sec-v4.0-rtic-memory";
+				reg = <0x20 0x20 0x200 0x80>;
+			};
+
+			rtic_c: rtic-c@40 {
+				compatible = "fsl,sec-v4.2-rtic-memory",
+					     "fsl,sec-v4.0-rtic-memory";
+				reg = <0x40 0x20 0x300 0x80>;
+			};
+
+			rtic_d: rtic-d@60 {
+				compatible = "fsl,sec-v4.2-rtic-memory",
+					     "fsl,sec-v4.0-rtic-memory";
+				reg = <0x60 0x20 0x500 0x80>;
+			};
+		};
+	};
+
+/include/ "pq3-mpic.dtsi"
+/include/ "pq3-mpic-timer-B.dtsi"
+
+	global-utilities@e0000 {
+		compatible = "fsl,p1023-guts";
+		reg = <0xe0000 0x1000>;
+		fsl,has-rstcr;
+	};
+};

arch/powerpc/boot/dts/fsl/p1023si-pre.dtsi

+/*
+ * P1023/P1017 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+	compatible = "fsl,P1023";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+		pci0 = &pci0;
+		pci1 = &pci1;
+		pci2 = &pci2;
+
+		crypto = &crypto;
+		sec_jr0 = &sec_jr0;
+		sec_jr1 = &sec_jr1;
+		sec_jr2 = &sec_jr2;
+		sec_jr3 = &sec_jr3;
+		rtic_a = &rtic_a;
+		rtic_b = &rtic_b;
+		rtic_c = &rtic_c;
+		rtic_d = &rtic_d;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,P1023@0 {
+			device_type = "cpu";
+			reg = <0x0>;
+			next-level-cache = <&L2>;
+		};
+
+		PowerPC,P1023@1 {
+			device_type = "cpu";
+			reg = <0x1>;
+			next-level-cache = <&L2>;
+		};
+	};
+};

arch/powerpc/boot/dts/fsl/p2020si-post.dtsi

+/*
+ * P2020/P2010 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	compatible = "fsl,p2020-elbc", "fsl,elbc", "simple-bus";
+	interrupts = <19 2 0 0>;
+};
+
+/* controller at 0xa000 */
+&pci0 {
+	compatible = "fsl,mpc8548-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <26 2 0 0>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <26 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x0 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x1 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0x2 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0x3 0x1 0x0 0x0
+			>;
+	};
+};
+
+/* controller at 0x9000 */
+&pci1 {
+	compatible = "fsl,mpc8548-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <25 2 0 0>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <25 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x4 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x5 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0x6 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0x7 0x1 0x0 0x0
+			>;
+	};
+};
+
+/* controller at 0x8000 */
+&pci2 {
+	compatible = "fsl,mpc8548-pcie";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 255>;
+	clock-frequency = <33333333>;
+	interrupts = <24 2 0 0>;
+
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <24 2 0 0>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0x0 0x0 0x1 &mpic 0x8 0x1 0x0 0x0
+			0000 0x0 0x0 0x2 &mpic 0x9 0x1 0x0 0x0
+			0000 0x0 0x0 0x3 &mpic 0xa 0x1 0x0 0x0
+			0000 0x0 0x0 0x4 &mpic 0xb 0x1 0x0 0x0
+			>;
+	};
+};
+
+&soc {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	device_type = "soc";
+	compatible = "fsl,p2020-immr", "simple-bus";
+	bus-frequency = <0>;		// Filled out by uboot.
+
+	ecm-law@0 {
+		compatible = "fsl,ecm-law";
+		reg = <0x0 0x1000>;
+		fsl,num-laws = <12>;
+	};
+
+	ecm@1000 {
+		compatible = "fsl,p2020-ecm", "fsl,ecm";
+		reg = <0x1000 0x1000>;
+		interrupts = <17 2 0 0>;
+	};
+
+	memory-controller@2000 {
+		compatible = "fsl,p2020-memory-controller";
+		reg = <0x2000 0x1000>;
+		interrupts = <18 2 0 0>;
+	};
+
+/include/ "pq3-i2c-0.dtsi"
+/include/ "pq3-i2c-1.dtsi"
+/include/ "pq3-duart-0.dtsi"
+/include/ "pq3-espi-0.dtsi"
+	spi0: spi@7000 {
+		fsl,espi-num-chipselects = <4>;
+	};
+
+/include/ "pq3-dma-1.dtsi"
+/include/ "pq3-gpio-0.dtsi"
+
+	L2: l2-cache-controller@20000 {
+		compatible = "fsl,p2020-l2-cache-controller";
+		reg = <0x20000 0x1000>;
+		cache-line-size = <32>;	// 32 bytes
+		cache-size = <0x80000>; // L2,512K
+		interrupts = <16 2 0 0>;
+	};
+
+/include/ "pq3-dma-0.dtsi"
+/include/ "pq3-usb2-dr-0.dtsi"
+/include/ "pq3-etsec1-0.dtsi"
+/include/ "pq3-etsec1-timer-0.dtsi"
+
+	ptp_clock@24e00 {
+		interrupts = <68 2 0 0 69 2 0 0 70 2 0 0>;
+	};
+
+
+/include/ "pq3-etsec1-1.dtsi"
+/include/ "pq3-etsec1-2.dtsi"
+/include/ "pq3-esdhc-0.dtsi"
+/include/ "pq3-sec3.1-0.dtsi"
+/include/ "pq3-mpic.dtsi"
+/include/ "pq3-mpic-timer-B.dtsi"
+
+	global-utilities@e0000 {
+		compatible = "fsl,p2020-guts";
+		reg = <0xe0000 0x1000>;
+		fsl,has-rstcr;
+	};
+};

arch/powerpc/boot/dts/fsl/p2020si-pre.dtsi

+/*
+ * P2020/P2010 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+	compatible = "fsl,P2020";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+		ethernet0 = &enet0;
+		ethernet1 = &enet1;
+		ethernet2 = &enet2;
+		pci0 = &pci0;
+		pci1 = &pci1;
+		pci2 = &pci2;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,P2020@0 {
+			device_type = "cpu";
+			reg = <0x0>;
+			next-level-cache = <&L2>;
+		};
+
+		PowerPC,P2020@1 {
+			device_type = "cpu";
+			reg = <0x1>;
+			next-level-cache = <&L2>;
+		};
+	};
+};

arch/powerpc/boot/dts/fsl/p2041si-post.dtsi

+/*
+ * P2041/P2040 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+	compatible = "fsl,p2041-elbc", "fsl,elbc", "simple-bus";
+	interrupts = <25 2 0 0>;
+	#address-cells = <2>;
+	#size-cells = <1>;
+};
+
+/* controller at 0x200000 */
+&pci0 {
+	compatible = "fsl,p2041-pcie", "fsl,qoriq-pcie-v2.2";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0x0 0xff>;
+	clock-frequency = <33333333>;
+	interrupts = <16 2 1 15>;
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <16 2 1 15>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0 0 1 &mpic 40 1 0 0
+			0000 0 0 2 &mpic 1 1 0 0
+			0000 0 0 3 &mpic 2 1 0 0
+			0000 0 0 4 &mpic 3 1 0 0
+			>;
+	};
+};
+
+/* controller at 0x201000 */
+&pci1 {
+	compatible = "fsl,p2041-pcie", "fsl,qoriq-pcie-v2.2";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 0xff>;
+	clock-frequency = <33333333>;
+	interrupts = <16 2 1 14>;
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <16 2 1 14>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0 0 1 &mpic 41 1 0 0
+			0000 0 0 2 &mpic 5 1 0 0
+			0000 0 0 3 &mpic 6 1 0 0
+			0000 0 0 4 &mpic 7 1 0 0
+			>;
+	};
+};
+
+/* controller at 0x202000 */
+&pci2 {
+	compatible = "fsl,p2041-pcie", "fsl,qoriq-pcie-v2.2";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0x0 0xff>;
+	clock-frequency = <33333333>;
+	interrupts = <16 2 1 13>;
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <16 2 1 13>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0 0 1 &mpic 42 1 0 0
+			0000 0 0 2 &mpic 9 1 0 0
+			0000 0 0 3 &mpic 10 1 0 0
+			0000 0 0 4 &mpic 11 1 0 0
+			>;
+	};
+};
+
+&rio {
+	compatible = "fsl,srio";
+	interrupts = <16 2 1 11>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+	ranges;
+
+	port1 {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		cell-index = <1>;
+	};
+
+	port2 {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		cell-index = <2>;
+	};
+};
+
+&dcsr {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "fsl,dcsr", "simple-bus";
+
+	dcsr-epu@0 {
+		compatible = "fsl,dcsr-epu";
+		interrupts = <52 2 0 0
+			      84 2 0 0
+			      85 2 0 0>;
+		reg = <0x0 0x1000>;
+	};
+	dcsr-npc {
+		compatible = "fsl,dcsr-npc";
+		reg = <0x1000 0x1000 0x1000000 0x8000>;
+	};
+	dcsr-nxc@2000 {
+		compatible = "fsl,dcsr-nxc";
+		reg = <0x2000 0x1000>;
+	};
+	dcsr-corenet {
+		compatible = "fsl,dcsr-corenet";
+		reg = <0x8000 0x1000 0xB0000 0x1000>;
+	};
+	dcsr-dpaa@9000 {
+		compatible = "fsl,p2041-dcsr-dpaa", "fsl,dcsr-dpaa";
+		reg = <0x9000 0x1000>;
+	};
+	dcsr-ocn@11000 {
+		compatible = "fsl,p2041-dcsr-ocn", "fsl,dcsr-ocn";
+		reg = <0x11000 0x1000>;
+	};
+	dcsr-ddr@12000 {
+		compatible = "fsl,dcsr-ddr";
+		dev-handle = <&ddr1>;
+		reg = <0x12000 0x1000>;
+	};
+	dcsr-nal@18000 {
+		compatible = "fsl,p2041-dcsr-nal", "fsl,dcsr-nal";
+		reg = <0x18000 0x1000>;
+	};
+	dcsr-rcpm@22000 {
+		compatible = "fsl,p2041-dcsr-rcpm", "fsl,dcsr-rcpm";
+		reg = <0x22000 0x1000>;
+	};
+	dcsr-cpu-sb-proxy@40000 {
+		compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+		cpu-handle = <&cpu0>;
+		reg = <0x40000 0x1000>;
+	};
+	dcsr-cpu-sb-proxy@41000 {
+		compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+		cpu-handle = <&cpu1>;
+		reg = <0x41000 0x1000>;
+	};
+	dcsr-cpu-sb-proxy@42000 {
+		compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+		cpu-handle = <&cpu2>;
+		reg = <0x42000 0x1000>;
+	};
+	dcsr-cpu-sb-proxy@43000 {
+		compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+		cpu-handle = <&cpu3>;
+		reg = <0x43000 0x1000>;
+	};
+};
+
+&soc {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	device_type = "soc";
+	compatible = "simple-bus";
+
+	soc-sram-error {
+		compatible = "fsl,soc-sram-error";
+		interrupts = <16 2 1 29>;
+	};
+
+	corenet-law@0 {
+		compatible = "fsl,corenet-law";
+		reg = <0x0 0x1000>;
+		fsl,num-laws = <32>;
+	};
+
+	ddr1: memory-controller@8000 {
+		compatible = "fsl,qoriq-memory-controller-v4.5", "fsl,qoriq-memory-controller";
+		reg = <0x8000 0x1000>;
+		interrupts = <16 2 1 23>;
+	};
+
+	cpc: l3-cache-controller@10000 {
+		compatible = "fsl,p2041-l3-cache-controller", "fsl,p4080-l3-cache-controller", "cache";
+		reg = <0x10000 0x1000>;
+		interrupts = <16 2 1 27>;
+	};
+
+	corenet-cf@18000 {
+		compatible = "fsl,corenet-cf";
+		reg = <0x18000 0x1000>;
+		interrupts = <16 2 1 31>;
+		fsl,ccf-num-csdids = <32>;
+		fsl,ccf-num-snoopids = <32>;
+	};
+
+	iommu@20000 {
+		compatible = "fsl,pamu-v1.0", "fsl,pamu";
+		reg = <0x20000 0x4000>;
+		interrupts = <
+			24 2 0 0
+			16 2 1 30>;
+	};
+
+/include/ "qoriq-mpic.dtsi"
+
+	guts: global-utilities@e0000 {
+		compatible = "fsl,qoriq-device-config-1.0";
+		reg = <0xe0000 0xe00>;
+		fsl,has-rstcr;
+		#sleep-cells = <1>;
+		fsl,liodn-bits = <12>;
+	};
+
+	pins: global-utilities@e0e00 {
+		compatible = "fsl,qoriq-pin-control-1.0";
+		reg = <0xe0e00 0x200>;
+		#sleep-cells = <2>;
+	};
+
+	clockgen: global-utilities@e1000 {
+		compatible = "fsl,p2041-clockgen", "fsl,qoriq-clockgen-1.0";
+		reg = <0xe1000 0x1000>;
+		clock-frequency = <0>;
+	};
+
+	rcpm: global-utilities@e2000 {
+		compatible = "fsl,qoriq-rcpm-1.0";
+		reg = <0xe2000 0x1000>;
+		#sleep-cells = <1>;
+	};
+
+	sfp: sfp@e8000 {
+		compatible = "fsl,p2041-sfp", "fsl,qoriq-sfp-1.0";
+		reg	   = <0xe8000 0x1000>;
+	};
+
+	serdes: serdes@ea000 {
+		compatible = "fsl,p2041-serdes";
+		reg	   = <0xea000 0x1000>;
+	};
+
+/include/ "qoriq-dma-0.dtsi"
+/include/ "qoriq-dma-1.dtsi"
+/include/ "qoriq-espi-0.dtsi"
+	spi@110000 {
+		fsl,espi-num-chipselects = <4>;
+	};
+
+/include/ "qoriq-esdhc-0.dtsi"
+	sdhc@114000 {
+		sdhci,auto-cmd12;
+	};
+
+/include/ "qoriq-i2c-0.dtsi"
+/include/ "qoriq-i2c-1.dtsi"
+/include/ "qoriq-duart-0.dtsi"
+/include/ "qoriq-duart-1.dtsi"
+/include/ "qoriq-gpio-0.dtsi"
+/include/ "qoriq-usb2-mph-0.dtsi"
+		usb0: usb@210000 {
+			phy_type = "utmi";
+			port0;
+		};
+
+/include/ "qoriq-usb2-dr-0.dtsi"
+		usb1: usb@211000 {
+			dr_mode = "host";
+			phy_type = "utmi";
+		};
+
+/include/ "qoriq-sata2-0.dtsi"
+/include/ "qoriq-sata2-1.dtsi"
+/include/ "qoriq-sec4.2-0.dtsi"
+};

arch/powerpc/boot/dts/fsl/p2041si-pre.dtsi

+/*
+ * P2041 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+/ {
+	compatible = "fsl,P2041";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&mpic>;
+
+	aliases {
+		ccsr = &soc;
+		dcsr = &dcsr;
+
+		serial0 = &serial0;
+		serial1 = &serial1;
+		serial2 = &serial2;
+		serial3 = &serial3;
+		pci0 = &pci0;
+		pci1 = &pci1;
+		pci2 = &pci2;
+		usb0 = &usb0;
+		usb1 = &usb1;
+		dma0 = &dma0;
+		dma1 = &dma1;
+		sdhc = &sdhc;
+		msi0 = &msi0;
+		msi1 = &msi1;
+		msi2 = &msi2;
+
+		crypto = &crypto;
+		sec_jr0 = &sec_jr0;
+		sec_jr1 = &sec_jr1;
+		sec_jr2 = &sec_jr2;
+		sec_jr3 = &sec_jr3;
+		rtic_a = &rtic_a;
+		rtic_b = &rtic_b;
+		rtic_c = &rtic_c;
+		rtic_d = &rtic_d;
+		sec_mon = &sec_mon;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: PowerPC,e500mc@0 {
+			device_type = "cpu";
+			reg = <0>;
+			next-level-cache = <&L2_0>;
+			L2_0: l2-cache {
+				next-level-cache = <&cpc>;
+			};
+		};
+		cpu1: PowerPC,e500mc@1 {
+			device_type = "cpu";
+			reg = <1>;
+			next-level-cache = <&L2_1>;
+			L2_1: l2-cache {
+				next-level-cache = <&cpc>;
+			};
+		};
+		cpu2: PowerPC,e500mc@2 {
+			device_type = "cpu";
+			reg = <2>;
+			next-level-cache = <&L2_2>;
+			L2_2: l2-cache {
+				next-level-cache = <&cpc>;
+			};
+		};
+		cpu3: PowerPC,e500mc@3 {
+			device_type = "cpu";
+			reg = <3>;
+			next-level-cache = <&L2_3>;
+			L2_3: l2-cache {
+				next-level-cache = <&cpc>;
+			};
+		};
+	};
+};

arch/powerpc/boot/dts/fsl/p3041si-post.dtsi

+/*
+ * P3041 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *     * Redistributions of source code must retain the above copyright
+ *       notice, this list of conditions and the following disclaimer.
+ *     * Redistributions in binary form must reproduce the above copyright
+ *       notice, this list of conditions and the following disclaimer in the
+ *       documentation and/or other materials provided with the distribution.
+ *     * Neither the name of Freescale Semiconductor nor the
+ *       names of its contributors may be used to endorse or promote products
+ *       derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+	compatible = "fsl,p3041-elbc", "fsl,elbc", "simple-bus";
+	interrupts = <25 2 0 0>;
+	#address-cells = <2>;
+	#size-cells = <1>;
+};
+
+/* controller at 0x200000 */
+&pci0 {
+	compatible = "fsl,p3041-pcie", "fsl,qoriq-pcie-v2.2";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0x0 0xff>;
+	clock-frequency = <33333333>;
+	interrupts = <16 2 1 15>;
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <16 2 1 15>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0 0 1 &mpic 40 1 0 0
+			0000 0 0 2 &mpic 1 1 0 0
+			0000 0 0 3 &mpic 2 1 0 0
+			0000 0 0 4 &mpic 3 1 0 0
+			>;
+	};
+};
+
+/* controller at 0x201000 */
+&pci1 {
+	compatible = "fsl,p3041-pcie", "fsl,qoriq-pcie-v2.2";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0 0xff>;
+	clock-frequency = <33333333>;
+	interrupts = <16 2 1 14>;
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <16 2 1 14>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0 0 1 &mpic 41 1 0 0
+			0000 0 0 2 &mpic 5 1 0 0
+			0000 0 0 3 &mpic 6 1 0 0
+			0000 0 0 4 &mpic 7 1 0 0
+			>;
+	};
+};
+
+/* controller at 0x202000 */
+&pci2 {
+	compatible = "fsl,p3041-pcie", "fsl,qoriq-pcie-v2.2";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0x0 0xff>;
+	clock-frequency = <33333333>;
+	interrupts = <16 2 1 13>;
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <16 2 1 13>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0 0 1 &mpic 42 1 0 0
+			0000 0 0 2 &mpic 9 1 0 0
+			0000 0 0 3 &mpic 10 1 0 0
+			0000 0 0 4 &mpic 11 1 0 0
+			>;
+	};
+};
+
+/* controller at 0x203000 */
+&pci3 {
+	compatible = "fsl,p3041-pcie", "fsl,qoriq-pcie-v2.2";
+	device_type = "pci";
+	#size-cells = <2>;
+	#address-cells = <3>;
+	bus-range = <0x0 0xff>;
+	clock-frequency = <33333333>;
+	interrupts = <16 2 1 12>;
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+		interrupts = <16 2 1 12>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = <
+			/* IDSEL 0x0 */
+			0000 0 0 1 &mpic 43 1 0 0
+			0000 0 0 2 &mpic 0 1 0 0
+			0000 0 0 3 &mpic 4 1 0 0
+			0000 0 0 4 &mpic 8 1 0 0
+			>;
+	};
+};
+
+&rio {
+	compatible = "fsl,srio";
+	interrupts = <16 2 1 11>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+	ranges;
+
+	port1 {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		cell-index = <1>;
+	};
+
+	port2 {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		cell-index = <2>;
+	};
+};
+
+&dcsr {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "fsl,dcsr", "simple-bus";
+
+	dcsr-epu@0 {
+		compatible = "fsl,dcsr-epu";
+		interrupts = <52 2 0 0
+			      84 2 0 0
+			      85 2 0 0>;
+		reg = <0x0 0x1000>;
+	};
+	dcsr-npc {
+		compatible = "fsl,dcsr-npc";
+		reg = <0x1000 0x1000 0x1000000 0x8000>;
+	};
+	dcsr-nxc@2000 {
+		compatible = "fsl,dcsr-nxc";
+		reg = <0x2000 0x1000>;
+	};
+	dcsr-corenet {
+		compatible = "fsl,dcsr-corenet";
+		reg = <0x8000 0x1000 0xB0000 0x1000>;
+	};
+	dcsr-dpaa@9000 {
+		compatible = "fsl,p3041-dcsr-dpaa", "fsl,dcsr-dpaa";
+		reg = <0x9000 0x1000>;
+	};
+	dcsr-ocn@11000 {
+		compatible = "fsl,p3041-dcsr-ocn", "fsl,dcsr-ocn";
+		reg = <0x11000 0x1000>;
+	};
+	dcsr-ddr@12000 {
+		compatible = "fsl,dcsr-ddr";
+		dev-handle = <&ddr1>;
+		reg = <0x12000 0x1000>;
+	};
+	dcsr-nal@18000 {
+		compatible = "fsl,p3041-dcsr-nal", "fsl,dcsr-nal";
+		reg = <0x18000 0x1000>;
+	};
+	dcsr-rcpm@22000 {
+		compatible = "fsl,p3041-dcsr-rcpm", "fsl,dcsr-rcpm";
+		reg = <0x22000 0x1000>;
+	};
+	dcsr-cpu-sb-proxy@40000 {
+		compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+		cpu-handle = <&cpu0>;
+		reg = <0x40000 0x1000>;
+	};
+	dcsr-cpu-sb-proxy@41000 {
+		compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+		cpu-handle = <&cpu1>;
+		reg = <0x41000 0x1000>;
+	};
+	dcsr-cpu-sb-proxy@42000 {
+		compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+		cpu-handle = <&cpu2>;
+		reg = <0x42000 0x1000>;
+	};
+	dcsr-cpu-sb-proxy@43000 {
+		compatible = "fsl,dcsr-e500mc-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+		cpu-handle = <&cpu3>;
+		reg = <0x43000 0x1000>;
+	};
+};
+
+&soc {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	device_type = "soc";
+	compatible = "simple-bus";
+
+	soc-sram-error {
+		compatible = "fsl,soc-sram-error";
+		interrupts = <16 2 1 29>;
+	};
+
+	corenet-law@0 {
+		compatible = "fsl,corenet-law";
+		reg = <0x0 0x1000>;
+		fsl,num-laws = <32>;
+	};
+
+	ddr1: memory-controller@8000 {
+		compatible = "fsl,qoriq-memory-controller-v4.5", "fsl,qoriq-memory-controller";
+		reg = <0x8000 0x1000>;
+		interrupts = <16 2 1 23>;
+	};
+
+	cpc: l3-cache-controller@10000 {
+		compatible = "fsl,p3041-l3-cache-controller", "fsl,p4080-l3-cache-controller", "cache";
+		reg = <0x10000 0x1000>;
+		interrupts = <16 2 1 27>;
+	};
+
+	corenet-cf@18000 {
+		compatible = "fsl,corenet-cf";
+		reg = <0x18000 0x1000>;
+		interrupts = <16 2 1 31>;
+		fsl,ccf-num-csdids = <32>;
+		fsl,ccf-num-snoopids = <32>;
+	};
+
+	iommu@20000 {
+		compatible = "fsl,pamu-v1.0", "fsl,pamu";
+		reg = <0x20000 0x4000>;
+		interrupts = <
+			24 2 0 0
+			16 2 1 30>;
+	};
+
+/include/ "qoriq-mpic.dtsi"
+
+	guts: global-utilities@e0000 {
+		compatible = "fsl,qoriq-device-config-1.0";
+		reg = <0xe0000 0xe00>;
+		fsl,has-rstcr;
+		#sleep-cells = <1>;
+		fsl,liodn-bits = <12>;
+	};
+
+	pins: global-utilities@e0e00 {
+		compatible = "fsl,qoriq-pin-control-1.0";
+		reg = <0xe0e00 0x200>;
+		#sleep-cells = <2>;
+	};
+
+	clockgen: global-utilities@e1000 {
+		compatible = "fsl,p3041-clockgen", "fsl,qoriq-clockgen-1.0";
+		reg = <0xe1000 0x1000>;
+		clock-frequency = <0>;
+	};
+
+	rcpm: global-utilities@e2000 {
+		compatible = "fsl,qoriq-rcpm-1.0";
+		reg = <0xe2000 0x1000>;
+		#sleep-cells = <1>;
+	};
+
+	sfp: sfp@e8000 {
+		compatible = "fsl,p3041-sfp", "fsl,qoriq-sfp-1.0";
+		reg	   = <0xe8000 0x1000>;
+	};
+
+	serdes: serdes@ea000 {
+		compatible = "fsl,p3041-serdes";
+		reg	   = <0xea000 0x1000>;
+	};
+
+/include/ "qoriq-dma-0.dtsi"
+/include/ "qoriq-dma-1.dtsi"
+/include/ "qoriq-espi-0.dtsi"
+	spi@110000 {
+		fsl,espi-num-chipselects = <4>;
+	};
+
+/include/ "qoriq-esdhc-0.dtsi"
+	sdhc@114000 {
+		sdhci,auto-cmd12;
+	};
+
+/include/ "qoriq-i2c-0.dtsi"
+/include/ "qoriq-i2c-1.dtsi"
+/include/ "qoriq-duart-0.dtsi"
+/include/ "qoriq-duart-1.dtsi"
+/include/ "qoriq-gpio-0.dtsi"
+/include/ "qoriq-usb2-mph-0.dtsi"
+		usb0: usb@210000 {
+			phy_type = "utmi";
+			port0;
+		};
+
+/include/ "qoriq-usb2-dr-0.dtsi"
+		usb1: usb@211000 {
+			dr_mode = "host";
+			phy_type = "utmi";
+		};
+
+/include/ "qoriq-sata2-0.dtsi"
+/include/ "qoriq-sata2-1.dtsi"
+/include/ "qoriq-sec4.2-0.dtsi"
+};

arch/powerpc/boot/dts/kmeter1.dts

@@ -80,7 +80,7 @@ i2c@3000 {
 		serial0: serial@4500 {
 			cell-index = <0>;
 			device_type = "serial";
-			compatible = "ns16550";
+			compatible = "fsl,ns16550", "ns16550";
 			reg = <0x4500 0x100>;
 			clock-frequency = <264000000>;
 			interrupts = <9 0x8>;