ARM: dts: bcm283x: Define MMC interfaces at board level

Starting with RPi 4 this is the first board, which doesn't use sdhost
as default SD interface. So the MMC interfaces should be defined finally at
board level. Since all boards using sdhci already does this, we can drop the
pinctrl part from bcm2835-rpi.dtsi.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Eric Anholt <eric@anholt.net>

arch/arm/boot/dts/bcm2835-rpi-a-plus.dts

@@ -107,6 +107,13 @@ &pwm {
 	status = "okay";
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;

arch/arm/boot/dts/bcm2835-rpi-a.dts

@@ -102,6 +102,13 @@ &pwm {
 	status = "okay";
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;

arch/arm/boot/dts/bcm2835-rpi-b-plus.dts

@@ -109,6 +109,13 @@ &pwm {
 	status = "okay";
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;

arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts

@@ -102,6 +102,13 @@ &pwm {
 	status = "okay";
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;

arch/arm/boot/dts/bcm2835-rpi-b.dts

@@ -97,6 +97,13 @@ &pwm {
 	status = "okay";
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;

arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts

@@ -81,6 +81,13 @@ &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;

arch/arm/boot/dts/bcm2835-rpi-zero-w.dts

@@ -116,6 +116,13 @@ brcmf: wifi@1 {
 	};
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio32 &uart0_ctsrts_gpio30>;

arch/arm/boot/dts/bcm2835-rpi-zero.dts

@@ -98,6 +98,13 @@ &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;

arch/arm/boot/dts/bcm2835-rpi.dtsi

@@ -68,19 +68,6 @@ &i2c2 {
 	status = "okay";
 };
 
-&sdhci {
-	pinctrl-names = "default";
-	pinctrl-0 = <&emmc_gpio48>;
-	bus-width = <4>;
-};
-
-&sdhost {
-	pinctrl-names = "default";
-	pinctrl-0 = <&sdhost_gpio48>;
-	status = "okay";
-	bus-width = <4>;
-};
-
 &usb {
 	power-domains = <&power RPI_POWER_DOMAIN_USB>;
 };

arch/arm/boot/dts/bcm2836-rpi-2-b.dts

@@ -113,6 +113,13 @@ &pwm {
 	status = "okay";
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;

arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts

@@ -80,6 +80,13 @@ &hdmi {
 	hpd-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
 };
 
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;