pinctrl: lynxpoint: Move GPIO driver to pin controller folder

Move Lynxpoint GPIO driver under Intel pin control umbrella
for further transformation to a real pin control driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

MAINTAINERS

@@ -8344,7 +8344,6 @@ S:	Maintained
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel.git
 F:	drivers/gpio/gpio-ich.c
 F:	drivers/gpio/gpio-intel-mid.c
-F:	drivers/gpio/gpio-lynxpoint.c
 F:	drivers/gpio/gpio-merrifield.c
 F:	drivers/gpio/gpio-ml-ioh.c
 F:	drivers/gpio/gpio-pch.c

drivers/gpio/Kconfig

@@ -335,14 +335,6 @@ config GPIO_LPC32XX
 	  Select this option to enable GPIO driver for
 	  NXP LPC32XX devices.
 
-config GPIO_LYNXPOINT
-	tristate "Intel Lynxpoint GPIO support"
-	depends on ACPI && X86
-	select GPIOLIB_IRQCHIP
-	help
-	  driver for GPIO functionality on Intel Lynxpoint PCH chipset
-	  Requires ACPI device enumeration code to set up a platform device.
-
 config GPIO_MB86S7X
 	tristate "GPIO support for Fujitsu MB86S7x Platforms"
 	help

drivers/gpio/Makefile

@@ -76,7 +76,6 @@ obj-$(CONFIG_GPIO_LP873X)		+= gpio-lp873x.o
 obj-$(CONFIG_GPIO_LP87565)		+= gpio-lp87565.o
 obj-$(CONFIG_GPIO_LPC18XX)		+= gpio-lpc18xx.o
 obj-$(CONFIG_GPIO_LPC32XX)		+= gpio-lpc32xx.o
-obj-$(CONFIG_GPIO_LYNXPOINT)		+= gpio-lynxpoint.o
 obj-$(CONFIG_GPIO_MADERA)		+= gpio-madera.o
 obj-$(CONFIG_GPIO_MAX3191X)		+= gpio-max3191x.o
 obj-$(CONFIG_GPIO_MAX7300)		+= gpio-max7300.o

drivers/pinctrl/intel/Kconfig

@@ -31,6 +31,16 @@ config PINCTRL_CHERRYVIEW
 	  Cherryview/Braswell pinctrl driver provides an interface that
 	  allows configuring of SoC pins and using them as GPIOs.
 
+config PINCTRL_LYNXPOINT
+	tristate "Intel Lynxpoint pinctrl and GPIO driver"
+	depends on ACPI
+	select GPIOLIB
+	select GPIOLIB_IRQCHIP
+	help
+	  Lynxpoint is the PCH of Intel Haswell. This pinctrl driver
+	  provides an interface that allows configuring of PCH pins and
+	  using them as GPIOs.
+
 config PINCTRL_MERRIFIELD
 	tristate "Intel Merrifield pinctrl driver"
 	depends on X86_INTEL_MID

drivers/pinctrl/intel/Makefile

@@ -3,6 +3,7 @@
 
 obj-$(CONFIG_PINCTRL_BAYTRAIL)		+= pinctrl-baytrail.o
 obj-$(CONFIG_PINCTRL_CHERRYVIEW)	+= pinctrl-cherryview.o
+obj-$(CONFIG_PINCTRL_LYNXPOINT)		+= pinctrl-lynxpoint.o
 obj-$(CONFIG_PINCTRL_MERRIFIELD)	+= pinctrl-merrifield.o
 obj-$(CONFIG_PINCTRL_INTEL)		+= pinctrl-intel.o
 obj-$(CONFIG_PINCTRL_BROXTON)		+= pinctrl-broxton.o