Commit f0752331 authored by Mark Brown's avatar Mark Brown

ASoC: Convert WM8900 to allow registration by machine code

This makes use of the support for delayed DAI registration to allow the
WM8900 I2C device to be registered by general platform/architecture code
rather than as part of the ASoC device probe.
Signed-off-by: default avatarMark Brown <broonie@opensource.wolfsonmicro.com>
parent 6b05eda6
......@@ -1382,32 +1382,21 @@ static int wm8900_init(struct snd_soc_device *socdev)
return ret;
}
static struct snd_soc_device *wm8900_socdev;
static struct i2c_client *wm8900_client;
#if defined(CONFIG_I2C) || defined(CONFIG_I2C_MODULE)
/* If the i2c layer weren't so broken, we could pass this kind of data
around */
static int wm8900_i2c_probe(struct i2c_client *i2c,
const struct i2c_device_id *id)
{
struct snd_soc_device *socdev = wm8900_socdev;
struct snd_soc_codec *codec = socdev->codec;
int ret;
i2c_set_clientdata(i2c, codec);
codec->control_data = i2c;
ret = wm8900_init(socdev);
if (ret < 0)
dev_err(&i2c->dev, "failed to initialise WM8900\n");
return ret;
wm8900_client = i2c;
wm8900_dai.dev = &i2c->dev;
return snd_soc_register_dai(&wm8900_dai);
}
static int wm8900_i2c_remove(struct i2c_client *client)
{
struct snd_soc_codec *codec = i2c_get_clientdata(client);
kfree(codec->reg_cache);
snd_soc_unregister_dai(&wm8900_dai);
wm8900_dai.dev = NULL;
wm8900_client = NULL;
return 0;
}
......@@ -1427,57 +1416,17 @@ static struct i2c_driver wm8900_i2c_driver = {
.id_table = wm8900_i2c_id,
};
static int wm8900_add_i2c_device(struct platform_device *pdev,
const struct wm8900_setup_data *setup)
{
struct i2c_board_info info;
struct i2c_adapter *adapter;
struct i2c_client *client;
int ret;
ret = i2c_add_driver(&wm8900_i2c_driver);
if (ret != 0) {
dev_err(&pdev->dev, "can't add i2c driver\n");
return ret;
}
memset(&info, 0, sizeof(struct i2c_board_info));
info.addr = setup->i2c_address;
strlcpy(info.type, "wm8900", I2C_NAME_SIZE);
adapter = i2c_get_adapter(setup->i2c_bus);
if (!adapter) {
dev_err(&pdev->dev, "can't get i2c adapter %d\n",
setup->i2c_bus);
goto err_driver;
}
client = i2c_new_device(adapter, &info);
i2c_put_adapter(adapter);
if (!client) {
dev_err(&pdev->dev, "can't add i2c device at 0x%x\n",
(unsigned int)info.addr);
goto err_driver;
}
return 0;
err_driver:
i2c_del_driver(&wm8900_i2c_driver);
return -ENODEV;
}
#endif
static int wm8900_probe(struct platform_device *pdev)
{
struct snd_soc_device *socdev = platform_get_drvdata(pdev);
struct wm8900_setup_data *setup;
struct snd_soc_codec *codec;
int ret = 0;
dev_info(&pdev->dev, "WM8900 Audio Codec\n");
if (!wm8900_client) {
dev_err(&pdev->dev, "I2C client not yet instantiated\n");
return -ENODEV;
}
setup = socdev->codec_data;
codec = kzalloc(sizeof(struct snd_soc_codec), GFP_KERNEL);
if (codec == NULL)
return -ENOMEM;
......@@ -1490,15 +1439,13 @@ static int wm8900_probe(struct platform_device *pdev)
codec->set_bias_level = wm8900_set_bias_level;
wm8900_socdev = socdev;
#if defined(CONFIG_I2C) || defined(CONFIG_I2C_MODULE)
if (setup->i2c_address) {
codec->hw_write = (hw_write_t)i2c_master_send;
ret = wm8900_add_i2c_device(pdev, setup);
}
#else
#error Non-I2C interfaces not yet supported
#endif
codec->hw_write = (hw_write_t)i2c_master_send;
codec->control_data = wm8900_client;
ret = wm8900_init(socdev);
if (ret != 0)
kfree(codec);
return ret;
}
......@@ -1513,10 +1460,6 @@ static int wm8900_remove(struct platform_device *pdev)
snd_soc_free_pcms(socdev);
snd_soc_dapm_free(socdev);
#if defined(CONFIG_I2C) || defined(CONFIG_I2C_MODULE)
i2c_unregister_device(codec->control_data);
i2c_del_driver(&wm8900_i2c_driver);
#endif
kfree(codec);
return 0;
......@@ -1532,13 +1475,13 @@ EXPORT_SYMBOL_GPL(soc_codec_dev_wm8900);
static int __devinit wm8900_modinit(void)
{
return snd_soc_register_dai(&wm8900_dai);
return i2c_add_driver(&wm8900_i2c_driver);
}
module_init(wm8900_modinit);
static void __exit wm8900_exit(void)
{
snd_soc_unregister_dai(&wm8900_dai);
i2c_del_driver(&wm8900_i2c_driver);
}
module_exit(wm8900_exit);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment