Blackfin arch: Fix CCLK and SCLK checks

Fix CCLK and SCLK checks, combine all arch checks into one file
for maintance. Checkins that remove more lines than they add are always
good.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

arch/blackfin/Kconfig

@@ -323,7 +323,7 @@ config CMDLINE
 	  to the kernel, you may specify one here. As a minimum, you should specify
 	  the memory size and the root device (e.g., mem=8M, root=/dev/nfs).
 
-comment "Board Setup"
+comment "Clock/PLL Setup"
 
 config CLKIN_HZ
 	int "Crystal Frequency in Hz"
@@ -335,6 +335,118 @@ config CLKIN_HZ
 	help
 	  The frequency of CLKIN crystal oscillator on the board in Hz.
 
+config BFIN_KERNEL_CLOCK
+	bool "Re-program Clocks while Kernel boots?"
+	default n
+	help
+	  This option decides if kernel clocks are re-programed from the
+	  bootloader settings. If the clocks are not set, the SDRAM settings
+	  are also not changed, and the Bootloader does 100% of the hardware
+	  configuration.
+
+config PLL_BYPASS
+        bool "Bypass PLL"
+        depends on BFIN_KERNEL_CLOCK
+        default n
+
+config CLKIN_HALF
+	bool "Half Clock In"
+	depends on BFIN_KERNEL_CLOCK && (! PLL_BYPASS)
+	default n
+	help
+	  If this is set the clock will be divided by 2, before it goes to the PLL.
+
+config VCO_MULT
+	int "VCO Multiplier"
+	depends on BFIN_KERNEL_CLOCK && (! PLL_BYPASS)
+	range 1 64
+	default "22" if BFIN533_EZKIT
+	default "45" if BFIN533_STAMP
+	default "20" if BFIN537_STAMP
+	default "22" if BFIN533_BLUETECHNIX_CM
+	default "20" if BFIN537_BLUETECHNIX_CM
+	default "20" if BFIN561_BLUETECHNIX_CM
+	default "20" if BFIN561_EZKIT
+	help
+	  This controls the frequency of the on-chip PLL. This can be between 1 and 64.
+	  PLL Frequency = (Crystal Frequency) * (this setting)
+
+choice
+	prompt "Core Clock Divider"
+	depends on BFIN_KERNEL_CLOCK
+	default CCLK_DIV_1
+	help
+	  This sets the frequency of the core. It can be 1, 2, 4 or 8
+	  Core Frequency = (PLL frequency) / (this setting)
+
+config CCLK_DIV_1
+	bool "1"
+
+config CCLK_DIV_2
+	bool "2"
+
+config CCLK_DIV_4
+	bool "4"
+
+config CCLK_DIV_8
+	bool "8"
+endchoice
+
+config SCLK_DIV
+	int "System Clock Divider"
+	depends on BFIN_KERNEL_CLOCK
+	range 1 15
+	default 5 if BFIN533_EZKIT
+	default 5 if BFIN533_STAMP
+	default 4 if BFIN537_STAMP
+	default 5 if BFIN533_BLUETECHNIX_CM
+	default 4 if BFIN537_BLUETECHNIX_CM
+	default 4 if BFIN561_BLUETECHNIX_CM
+	default 5 if BFIN561_EZKIT
+	help
+	  This sets the frequency of the system clock (including SDRAM or DDR).
+	  This can be between 1 and 15
+	  System Clock = (PLL frequency) / (this setting)
+
+#
+# Max & Min Speeds for various Chips
+#
+config MAX_VCO_HZ
+	int
+	default 600000000 if BF522
+	default 600000000 if BF525
+	default 600000000 if BF527
+	default 400000000 if BF531
+	default 400000000 if BF532
+	default 750000000 if BF533
+	default 500000000 if BF534
+	default 400000000 if BF536
+	default 600000000 if BF537
+	default 533000000 if BF538
+	default 533000000 if BF539
+	default 600000000 if BF542
+	default 533000000 if BF544
+	default 533000000 if BF549
+	default 600000000 if BF561
+
+config MIN_VCO_HZ
+	int
+	default 50000000
+
+config MAX_SCLK_HZ
+	int
+	default 133000000
+
+config MIN_SCLK_HZ
+	int
+	default 27000000
+
+comment "Kernel Timer/Scheduler"
+
+source kernel/Kconfig.hz
+
+comment "Memory Setup"
+
 config MEM_SIZE
 	int "SDRAM Memory Size in MBytes"
 	default  32 if BFIN533_EZKIT
@@ -448,10 +560,6 @@ endmenu
 
 menu "Blackfin Kernel Optimizations"
 
-comment "Timer Tick"
-
-source kernel/Kconfig.hz
-
 comment "Memory Optimizations"
 
 config I_ENTRY_L1
@@ -672,63 +780,6 @@ config L1_MAX_PIECE
 	  Set the max memory pieces for the L1 SRAM allocation algorithm.
 	  Min value is 16. Max value is 1024.
 
-menu "Clock Settings"
-
-
-config BFIN_KERNEL_CLOCK
-	bool "Re-program Clocks while Kernel boots?"
-	default n
-	help
-	  This option decides if kernel clocks are re-programed from the
-	  bootloader settings. If the clocks are not set, the SDRAM settings
-	  are also not changed, and the Bootloader does 100% of the hardware
-	  configuration.
-
-config VCO_MULT
-	int "VCO Multiplier"
-	depends on BFIN_KERNEL_CLOCK
-	default "22" if BFIN533_EZKIT
-	default "45" if BFIN533_STAMP
-	default "20" if BFIN537_STAMP
-	default "22" if BFIN533_BLUETECHNIX_CM
-	default "20" if BFIN537_BLUETECHNIX_CM
-	default "20" if BFIN561_BLUETECHNIX_CM
-	default "20" if BFIN561_EZKIT
-
-config CCLK_DIV
-	int "Core Clock Divider"
-	depends on BFIN_KERNEL_CLOCK
-	default 1 if BFIN533_EZKIT
-	default 1 if BFIN533_STAMP
-	default 1 if BFIN537_STAMP
-	default 1 if BFIN533_BLUETECHNIX_CM
-	default 1 if BFIN537_BLUETECHNIX_CM
-	default 1 if BFIN561_BLUETECHNIX_CM
-	default 1 if BFIN561_EZKIT
-
-config SCLK_DIV
-	int "System Clock Divider"
-	depends on BFIN_KERNEL_CLOCK
-	default 5 if BFIN533_EZKIT
-	default 5 if BFIN533_STAMP
-	default 4 if BFIN537_STAMP
-	default 5 if BFIN533_BLUETECHNIX_CM
-	default 4 if BFIN537_BLUETECHNIX_CM
-	default 4 if BFIN561_BLUETECHNIX_CM
-	default 5 if BFIN561_EZKIT
-
-config CLKIN_HALF
-	bool "Half ClockIn"
-	depends on BFIN_KERNEL_CLOCK
-	default n
-
-config PLL_BYPASS
-	bool "Bypass PLL"
-	depends on BFIN_KERNEL_CLOCK
-	default n
-
-endmenu
-
 comment "Asynchonous Memory Configuration"
 
 menu "EBIU_AMBCTL Global Control"

arch/blackfin/mach-bf533/head.S

@@ -32,6 +32,7 @@
 #include <asm/blackfin.h>
 #include <asm/trace.h>
 #if CONFIG_BFIN_KERNEL_CLOCK
+#include <asm/mach-common/clocks.h>
 #include <asm/mach/mem_init.h>
 #endif
 #if CONFIG_DEBUG_KERNEL_START

arch/blackfin/mach-bf537/head.S

@@ -33,6 +33,7 @@
 #include <asm/trace.h>
 
 #if CONFIG_BFIN_KERNEL_CLOCK
+#include <asm/mach-common/clocks.h>
 #include <asm/mach/mem_init.h>
 #endif
 

arch/blackfin/mach-bf548/head.S

@@ -31,6 +31,7 @@
 #include <asm/blackfin.h>
 #include <asm/trace.h>
 #if CONFIG_BFIN_KERNEL_CLOCK
+#include <asm/mach-common/clocks.h>
 #include <asm/mach/mem_init.h>
 #endif
 

arch/blackfin/mach-bf561/head.S

@@ -33,6 +33,7 @@
 #include <asm/trace.h>
 
 #if CONFIG_BFIN_KERNEL_CLOCK
+#include <asm/mach-common/clocks.h>
 #include <asm/mach/mem_init.h>
 #endif
 

arch/blackfin/mach-common/Makefile

@@ -4,7 +4,7 @@
 
 obj-y := \
 	cache.o cacheinit.o cplbhdlr.o cplbmgr.o entry.o \
-	interrupt.o lock.o irqpanic.o
+	interrupt.o lock.o irqpanic.o arch_checks.o
 
 obj-$(CONFIG_CPLB_INFO)          += cplbinfo.o
 obj-$(CONFIG_BFIN_SINGLE_CORE)   += ints-priority-sc.o

arch/blackfin/mach-common/arch_checks.c

+/*
+ * File:         arch/blackfin/mach-common/arch_checks.c
+ * Based on:
+ * Author:	 Robin Getz <rgetz@blackfin.uclinux.org>
+ *
+ * Created:      25Jul07
+ * Description:  Do some checking to make sure things are OK
+ *
+ * Modified:
+ *               Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <asm/mach/anomaly.h>
+#include <asm/mach-common/clocks.h>
+
+#ifdef CONFIG_BFIN_KERNEL_CLOCK
+
+# if (CONFIG_VCO_HZ > CONFIG_MAX_VCO_HZ)
+#  error "VCO selected is more than maximum value. Please change the VCO multipler"
+# endif
+
+# if (CONFIG_SCLK_HZ > CONFIG_MAX_SCLK_HZ)
+# error "Sclk value selected is more than maximum. Please select a proper value for SCLK multiplier"
+# endif
+
+# if (CONFIG_SCLK_HZ < CONFIG_MIN_SCLK_HZ)
+# error "Sclk value selected is less than minimum. Please select a proper value for SCLK multiplier"
+# endif
+
+# if (ANOMALY_05000273) && (CONFIG_SCLK_HZ * 2 > CONFIG_CCLK_HZ)
+# error "ANOMALY 05000273, please make sure CCLK is at least 2x SCLK"
+# endif
+
+# if (CONFIG_SCLK_HZ > CONFIG_CCLK_HZ) && (CONFIG_SCLK_HZ != CONFIG_CLKIN_HZ) && (CONFIG_CCLK_HZ != CONFIG_CLKIN_HZ)
+# error "Please select sclk less than cclk"
+# endif
+
+#endif /* CONFIG_BFIN_KERNEL_CLOCK */

arch/blackfin/mach-common/dpmc.S

@@ -300,7 +300,7 @@ ENTRY(_sleep_deeper)
 	P0.H = hi(PLL_CTL);
 	P0.L = lo(PLL_CTL);
 	R5 = W[P0](z);
-	R0.L = (MIN_VC/CONFIG_CLKIN_HZ) << 9;
+	R0.L = (CONFIG_MIN_VCO_HZ/CONFIG_CLKIN_HZ) << 9;
 	W[P0] = R0.l;
 
 	SSYNC;

include/asm-blackfin/mach-bf533/bf533.h

@@ -141,97 +141,6 @@
 
 #define AMGCTLVAL	(V_AMBEN | V_AMCKEN | V_CDPRIO)
 
-#define MAX_VC	650000000
-#define MIN_VC	50000000
-
-#ifdef CONFIG_BFIN_KERNEL_CLOCK
-/********************************PLL Settings **************************************/
-#if (CONFIG_VCO_MULT < 0)
-#error "VCO Multiplier is less than 0. Please select a different value"
-#endif
-
-#if (CONFIG_VCO_MULT == 0)
-#error "VCO Multiplier should be greater than 0. Please select a different value"
-#endif
-
-#if (CONFIG_VCO_MULT > 64)
-#error "VCO Multiplier is more than 64. Please select a different value"
-#endif
-
-#ifndef CONFIG_CLKIN_HALF
-#define CONFIG_VCO_HZ	(CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)
-#else
-#define CONFIG_VCO_HZ	((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)/2)
-#endif
-
-#ifndef CONFIG_PLL_BYPASS
-#define CONFIG_CCLK_HZ	(CONFIG_VCO_HZ/CONFIG_CCLK_DIV)
-#define CONFIG_SCLK_HZ	(CONFIG_VCO_HZ/CONFIG_SCLK_DIV)
-#else
-#define CONFIG_CCLK_HZ	CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ	CONFIG_CLKIN_HZ
-#endif
-
-#if (CONFIG_SCLK_DIV < 1)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_SCLK_DIV > 15)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_CCLK_DIV != 1)
-#if (CONFIG_CCLK_DIV != 2)
-#if (CONFIG_CCLK_DIV != 4)
-#if (CONFIG_CCLK_DIV != 8)
-#error "CCLK DIV can be 1,2,4 or 8 only. Please select a proper value"
-#endif
-#endif
-#endif
-#endif
-
-#if (CONFIG_VCO_HZ > MAX_VC)
-#error "VCO selected is more than maximum value. Please change the VCO multipler"
-#endif
-
-#if (CONFIG_SCLK_HZ > 133000000)
-#error "Sclk value selected is more than maximum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ < 27000000)
-#error "Sclk value selected is less than minimum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ > CONFIG_CCLK_HZ)
-#if (CONFIG_SCLK_HZ != CONFIG_CLKIN_HZ)
-#if (CONFIG_CCLK_HZ != CONFIG_CLKIN_HZ)
-#error "Please select sclk less than cclk"
-#endif
-#endif
-#endif
-
-#if (CONFIG_CCLK_DIV == 1)
-#define CONFIG_CCLK_ACT_DIV   CCLK_DIV1
-#endif
-#if (CONFIG_CCLK_DIV == 2)
-#define CONFIG_CCLK_ACT_DIV   CCLK_DIV2
-#endif
-#if (CONFIG_CCLK_DIV == 4)
-#define CONFIG_CCLK_ACT_DIV   CCLK_DIV4
-#endif
-#if (CONFIG_CCLK_DIV == 8)
-#define CONFIG_CCLK_ACT_DIV   CCLK_DIV8
-#endif
-#ifndef CONFIG_CCLK_ACT_DIV
-#define CONFIG_CCLK_ACT_DIV   CONFIG_CCLK_DIV_not_defined_properly
-#endif
-
-#if ANOMALY_05000273 && (CONFIG_CCLK_DIV == 1)
-#error ANOMALY 05000273, please make sure CCLK is at least 2x SCLK
-#endif
-
-#endif				/* CONFIG_BFIN_KERNEL_CLOCK */
-
 #ifdef CONFIG_BF533
 #define CPU "BF533"
 #define CPUID 0x027a5000

include/asm-blackfin/mach-bf537/bf537.h

@@ -121,97 +121,6 @@
 
 #define AMGCTLVAL	(V_AMBEN | V_AMCKEN | V_CDPRIO)
 
-#define MAX_VC	650000000
-#define MIN_VC	50000000
-
-/********************************PLL Settings **************************************/
-#ifdef CONFIG_BFIN_KERNEL_CLOCK
-#if (CONFIG_VCO_MULT < 0)
-#error "VCO Multiplier is less than 0. Please select a different value"
-#endif
-
-#if (CONFIG_VCO_MULT == 0)
-#error "VCO Multiplier should be greater than 0. Please select a different value"
-#endif
-
-#if (CONFIG_VCO_MULT > 64)
-#error "VCO Multiplier is more than 64. Please select a different value"
-#endif
-
-#ifndef CONFIG_CLKIN_HALF
-#define CONFIG_VCO_HZ	(CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)
-#else
-#define CONFIG_VCO_HZ	((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)/2)
-#endif
-
-#ifndef CONFIG_PLL_BYPASS
-#define CONFIG_CCLK_HZ	(CONFIG_VCO_HZ/CONFIG_CCLK_DIV)
-#define CONFIG_SCLK_HZ	(CONFIG_VCO_HZ/CONFIG_SCLK_DIV)
-#else
-#define CONFIG_CCLK_HZ	CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ	CONFIG_CLKIN_HZ
-#endif
-
-#if (CONFIG_SCLK_DIV < 1)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_SCLK_DIV > 15)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_CCLK_DIV != 1)
-#if (CONFIG_CCLK_DIV != 2)
-#if (CONFIG_CCLK_DIV != 4)
-#if (CONFIG_CCLK_DIV != 8)
-#error "CCLK DIV can be 1,2,4 or 8 only. Please select a proper value"
-#endif
-#endif
-#endif
-#endif
-
-#if (CONFIG_VCO_HZ > MAX_VC)
-#error "VCO selected is more than maximum value. Please change the VCO multipler"
-#endif
-
-#if (CONFIG_SCLK_HZ > 133000000)
-#error "Sclk value selected is more than maximum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ < 27000000)
-#error "Sclk value selected is less than minimum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ >= CONFIG_CCLK_HZ)
-#if (CONFIG_SCLK_HZ != CONFIG_CLKIN_HZ)
-#if (CONFIG_CCLK_HZ != CONFIG_CLKIN_HZ)
-#error "Please select sclk less than cclk"
-#endif
-#endif
-#endif
-
-#if (CONFIG_CCLK_DIV == 1)
-#define CONFIG_CCLK_ACT_DIV   CCLK_DIV1
-#endif
-#if (CONFIG_CCLK_DIV == 2)
-#define CONFIG_CCLK_ACT_DIV   CCLK_DIV2
-#endif
-#if (CONFIG_CCLK_DIV == 4)
-#define CONFIG_CCLK_ACT_DIV   CCLK_DIV4
-#endif
-#if (CONFIG_CCLK_DIV == 8)
-#define CONFIG_CCLK_ACT_DIV   CCLK_DIV8
-#endif
-#ifndef CONFIG_CCLK_ACT_DIV
-#define CONFIG_CCLK_ACT_DIV   CONFIG_CCLK_DIV_not_defined_properly
-#endif
-
-#if ANOMALY_05000273 && (CONFIG_CCLK_DIV == 1)
-#error ANOMALY 05000273, please make sure CCLK is at least 2x SCLK
-#endif
-
-#endif				/* CONFIG_BFIN_KERNEL_CLOCK */
-
 #ifdef CONFIG_BF537
 #define CPU "BF537"
 #define CPUID 0x027c8000

include/asm-blackfin/mach-bf548/bf548.h

@@ -106,93 +106,6 @@
 
 #define AMGCTLVAL	(V_AMBEN | V_AMCKEN)
 
-#define MAX_VC	650000000
-#define MIN_VC	50000000
-
-/********************************PLL Settings **************************************/
-#ifdef CONFIG_BFIN_KERNEL_CLOCK
-#if (CONFIG_VCO_MULT < 0)
-#error "VCO Multiplier is less than 0. Please select a different value"
-#endif
-
-#if (CONFIG_VCO_MULT == 0)
-#error "VCO Multiplier should be greater than 0. Please select a different value"
-#endif
-
-#if (CONFIG_VCO_MULT > 64)
-#error "VCO Multiplier is more than 64. Please select a different value"
-#endif
-
-#ifndef CONFIG_CLKIN_HALF
-#define CONFIG_VCO_HZ	(CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)
-#else
-#define CONFIG_VCO_HZ	((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)/2)
-#endif
-
-#ifndef CONFIG_PLL_BYPASS
-#define CONFIG_CCLK_HZ	(CONFIG_VCO_HZ/CONFIG_CCLK_DIV)
-#define CONFIG_SCLK_HZ	(CONFIG_VCO_HZ/CONFIG_SCLK_DIV)
-#else
-#define CONFIG_CCLK_HZ	CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ	CONFIG_CLKIN_HZ
-#endif
-
-#if (CONFIG_SCLK_DIV < 1)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_SCLK_DIV > 15)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_CCLK_DIV != 1)
-#if (CONFIG_CCLK_DIV != 2)
-#if (CONFIG_CCLK_DIV != 4)
-#if (CONFIG_CCLK_DIV != 8)
-#error "CCLK DIV can be 1,2,4 or 8 only. Please select a proper value"
-#endif
-#endif
-#endif
-#endif
-
-#if (CONFIG_VCO_HZ > MAX_VC)
-#error "VCO selected is more than maximum value. Please change the VCO multipler"
-#endif
-
-#if (CONFIG_SCLK_HZ > 133000000)
-#error "Sclk value selected is more than maximum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ < 27000000)
-#error "Sclk value selected is less than minimum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ >= CONFIG_CCLK_HZ)
-#if (CONFIG_SCLK_HZ != CONFIG_CLKIN_HZ)
-#if (CONFIG_CCLK_HZ != CONFIG_CLKIN_HZ)
-#error "Please select sclk less than cclk"
-#endif
-#endif
-#endif
-
-#if (CONFIG_CCLK_DIV == 1)
-#define CONFIG_CCLK_ACT_DIV   CCLK_DIV1
-#endif
-#if (CONFIG_CCLK_DIV == 2)
-#define CONFIG_CCLK_ACT_DIV   CCLK_DIV2
-#endif
-#if (CONFIG_CCLK_DIV == 4)
-#define CONFIG_CCLK_ACT_DIV   CCLK_DIV4
-#endif
-#if (CONFIG_CCLK_DIV == 8)
-#define CONFIG_CCLK_ACT_DIV   CCLK_DIV8
-#endif
-#ifndef CONFIG_CCLK_ACT_DIV
-#define CONFIG_CCLK_ACT_DIV   CONFIG_CCLK_DIV_not_defined_properly
-#endif
-
-#endif	/* CONFIG_BFIN_KERNEL_CLOCK */
-
 #ifdef CONFIG_BF542
 #define CPU "BF542"
 #define CPUID 0x027c8000

include/asm-blackfin/mach-bf561/bf561.h

@@ -230,93 +230,6 @@
 
 #define AMGCTLVAL	(V_AMBEN | V_AMCKEN | V_CDPRIO | V_B0PEN | V_B1PEN | V_B2PEN | V_B3PEN | 0x0002)
 
-#define MAX_VC	600000000
-#define MIN_VC	50000000
-
-/******************************* PLL Settings ********************************/
-#ifdef CONFIG_BFIN_KERNEL_CLOCK
-#if (CONFIG_VCO_MULT < 0)
-#error "VCO Multiplier is less than 0. Please select a different value"
-#endif
-
-#if (CONFIG_VCO_MULT == 0)
-#error "VCO Multiplier should be greater than 0. Please select a different value"
-#endif
-
-#ifndef CONFIG_CLKIN_HALF
-#define CONFIG_VCO_HZ	(CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)
-#else
-#define CONFIG_VCO_HZ	((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)/2)
-#endif
-
-#ifndef CONFIG_PLL_BYPASS
-#define CONFIG_CCLK_HZ	(CONFIG_VCO_HZ/CONFIG_CCLK_DIV)
-#define CONFIG_SCLK_HZ	(CONFIG_VCO_HZ/CONFIG_SCLK_DIV)
-#else
-#define CONFIG_CCLK_HZ	CONFIG_CLKIN_HZ
-#define CONFIG_SCLK_HZ	CONFIG_CLKIN_HZ
-#endif
-
-#if (CONFIG_SCLK_DIV < 1)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_SCLK_DIV > 15)
-#error "SCLK DIV cannot be less than 1 or more than 15. Please select a proper value"
-#endif
-
-#if (CONFIG_CCLK_DIV != 1)
-#if (CONFIG_CCLK_DIV != 2)
-#if (CONFIG_CCLK_DIV != 4)
-#if (CONFIG_CCLK_DIV != 8)
-#error "CCLK DIV can be 1,2,4 or 8 only. Please select a proper value"
-#endif
-#endif
-#endif
-#endif
-
-#if (CONFIG_VCO_HZ > MAX_VC)
-#error "VCO selected is more than maximum value. Please change the VCO multipler"
-#endif
-
-#if (CONFIG_SCLK_HZ > 133000000)
-#error "Sclk value selected is more than maximum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ < 27000000)
-#error "Sclk value selected is less than minimum. Please select a proper value for SCLK multiplier"
-#endif
-
-#if (CONFIG_SCLK_HZ >= CONFIG_CCLK_HZ)
-#if (CONFIG_SCLK_HZ != CONFIG_CLKIN_HZ)
-#if (CONFIG_CCLK_HZ != CONFIG_CLKIN_HZ)
-#error "Please select sclk less than cclk"
-#endif
-#endif
-#endif
-
-#if (CONFIG_CCLK_DIV == 1)
-#define CONFIG_CCLK_ACT_DIV   CCLK_DIV1
-#endif
-#if (CONFIG_CCLK_DIV == 2)
-#define CONFIG_CCLK_ACT_DIV   CCLK_DIV2
-#endif
-#if (CONFIG_CCLK_DIV == 4)
-#define CONFIG_CCLK_ACT_DIV   CCLK_DIV4
-#endif
-#if (CONFIG_CCLK_DIV == 8)
-#define CONFIG_CCLK_ACT_DIV   CCLK_DIV8
-#endif
-#ifndef CONFIG_CCLK_ACT_DIV
-#define CONFIG_CCLK_ACT_DIV   CONFIG_CCLK_DIV_not_defined_properly
-#endif
-
-#if ANOMALY_05000273 && (CONFIG_CCLK_DIV == 1)
-#error ANOMALY 05000273, please make sure CCLK is at least 2x SCLK
-#endif
-
-#endif				/* CONFIG_BFIN_KERNEL_CLOCK */
-
 #ifdef CONFIG_BF561
 #define CPU "BF561"
 #define CPUID 0x027bb000

include/asm-blackfin/mach-common/clocks.h

+/*
+ * File:         include/asm-blackfin/mach-common/clocks.h
+ * Based on:     include/asm-blackfin/mach-bf537/bf537.h
+ * Author:	 Robin Getz <rgetz@blackfin.uclinux.org>
+ *
+ * Created:      25Jul07
+ * Description:  Common Clock definitions for various kernel files
+ *
+ * Modified:
+ *               Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+
+
+#ifdef CONFIG_CCLK_DIV_1
+# define CONFIG_CCLK_ACT_DIV   CCLK_DIV1
+# define CONFIG_CCLK_DIV 1
+#endif
+
+#ifdef CONFIG_CCLK_DIV_2
+# define CONFIG_CCLK_ACT_DIV   CCLK_DIV2
+# define CONFIG_CCLK_DIV 2
+#endif
+
+#ifdef CONFIG_CCLK_DIV_4
+# define CONFIG_CCLK_ACT_DIV   CCLK_DIV4
+# define CONFIG_CCLK_DIV 4
+#endif
+
+#ifdef CONFIG_CCLK_DIV_8
+# define CONFIG_CCLK_ACT_DIV   CCLK_DIV8
+# define CONFIG_CCLK_DIV 8
+#endif
+
+#ifndef CONFIG_PLL_BYPASS
+# ifndef CONFIG_CLKIN_HALF
+#  define CONFIG_VCO_HZ   (CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)
+# else
+#  define CONFIG_VCO_HZ   ((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT)/2)
+# endif
+
+# define CONFIG_CCLK_HZ  (CONFIG_VCO_HZ/CONFIG_CCLK_DIV)
+# define CONFIG_SCLK_HZ  (CONFIG_VCO_HZ/CONFIG_SCLK_DIV)
+
+#else
+# define CONFIG_VCO_HZ   (CONFIG_CLKIN_HZ)
+# define CONFIG_CCLK_HZ  (CONFIG_CLKIN_HZ)
+# define CONFIG_SCLK_HZ  (CONFIG_CLKIN_HZ)
+# define CONFIG_VCO_MULT 0
+#endif
+