Merge tag 'imx-fixes-5.6' of...

Merge tag 'imx-fixes-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes

i.MX fixes for 5.6:

 - Build v7_cpu_resume() unconditionally to fix system hang in case that
   suspend is disabled but cpuidle support is enabled.
 - Drop unexisting Ethernet PHY device from imx8qxp-mek board.
 - Fix SRAM compatible strings on imx6dl-colibri-eval-v3 board.
 - Fix imx-scu driver to make sure that all messages words are written
   sequentially.
 - A series from Leonard Crestez to fix i.MX SC API users, having all
   messages aligned on 4 bytes.
 - Fix eMMC supply for phycore-som board.
 - Drop bogus frequency setting from imx7-colibri SD/MMC device, so that
   HS200 mode starts working and delivers better performance.
 - Fix opp-supported-hw for i.MX7D to get consumer and industrial parts
   work with correct frequency settings.
 - Restore MDIO compatible to the correct one for LS1021A SoC.

* tag 'imx-fixes-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  soc: imx-scu: Align imx sc msg structs to 4
  firmware: imx: Align imx_sc_msg_req_cpu_start to 4
  firmware: imx: scu-pd: Align imx sc msg structs to 4
  firmware: imx: misc: Align imx sc msg structs to 4
  firmware: imx: scu: Ensure sequential TX
  ARM: dts: imx7-colibri: Fix frequency for sd/mmc
  arm64: dts: imx8qxp-mek: Remove unexisting Ethernet PHY
  ARM: dts: imx6dl-colibri-eval-v3: fix sram compatible properties
  ARM: dts: ls1021a: Restore MDIO compatible to gianfar
  ARM: dts: imx7d: fix opp-supported-hw
  ARM: imx: build v7_cpu_resume() unconditionally
  ARM: dts: imx6: phycore-som: fix emmc supply

Link: https://lore.kernel.org/r/20200224120334.GH27688@dragonSigned-off-by: Olof Johansson <olof@lixom.net>

arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts

@@ -275,7 +275,7 @@ &weim {
 
 	/* SRAM on Colibri nEXT_CS0 */
 	sram@0,0 {
-		compatible = "cypress,cy7c1019dv33-10zsxi, mtd-ram";
+		compatible = "cypress,cy7c1019dv33-10zsxi", "mtd-ram";
 		reg = <0 0 0x00010000>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -286,7 +286,7 @@ sram@0,0 {
 
 	/* SRAM on Colibri nEXT_CS1 */
 	sram@1,0 {
-		compatible = "cypress,cy7c1019dv33-10zsxi, mtd-ram";
+		compatible = "cypress,cy7c1019dv33-10zsxi", "mtd-ram";
 		reg = <1 0 0x00010000>;
 		#address-cells = <1>;
 		#size-cells = <1>;

arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi

@@ -192,7 +192,6 @@ &usdhc4 {
 	pinctrl-0 = <&pinctrl_usdhc4>;
 	bus-width = <8>;
 	non-removable;
-	vmmc-supply = <&vdd_emmc_1p8>;
 	status = "disabled";
 };
 

arch/arm/boot/dts/imx7-colibri.dtsi

@@ -336,7 +336,6 @@ &usdhc3 {
 	assigned-clock-rates = <400000000>;
 	bus-width = <8>;
 	fsl,tuning-step = <2>;
-	max-frequency = <100000000>;
 	vmmc-supply = <&reg_module_3v3>;
 	vqmmc-supply = <&reg_DCDC3>;
 	non-removable;

arch/arm/boot/dts/imx7d.dtsi

@@ -44,7 +44,7 @@ opp-792000000 {
 			opp-hz = /bits/ 64 <792000000>;
 			opp-microvolt = <1000000>;
 			clock-latency-ns = <150000>;
-			opp-supported-hw = <0xd>, <0xf>;
+			opp-supported-hw = <0xd>, <0x7>;
 			opp-suspend;
 		};
 
@@ -52,7 +52,7 @@ opp-996000000 {
 			opp-hz = /bits/ 64 <996000000>;
 			opp-microvolt = <1100000>;
 			clock-latency-ns = <150000>;
-			opp-supported-hw = <0xc>, <0xf>;
+			opp-supported-hw = <0xc>, <0x7>;
 			opp-suspend;
 		};
 
@@ -60,7 +60,7 @@ opp-1200000000 {
 			opp-hz = /bits/ 64 <1200000000>;
 			opp-microvolt = <1225000>;
 			clock-latency-ns = <150000>;
-			opp-supported-hw = <0x8>, <0xf>;
+			opp-supported-hw = <0x8>, <0x3>;
 			opp-suspend;
 		};
 	};

arch/arm/boot/dts/ls1021a.dtsi

@@ -747,7 +747,7 @@ dcu: dcu@2ce0000 {
 		};
 
 		mdio0: mdio@2d24000 {
-			compatible = "fsl,etsec2-mdio";
+			compatible = "gianfar";
 			device_type = "mdio";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -756,7 +756,7 @@ mdio0: mdio@2d24000 {
 		};
 
 		mdio1: mdio@2d64000 {
-			compatible = "fsl,etsec2-mdio";
+			compatible = "gianfar";
 			device_type = "mdio";
 			#address-cells = <1>;
 			#size-cells = <0>;

arch/arm/mach-imx/Makefile

@@ -91,6 +91,8 @@ AFLAGS_suspend-imx6.o :=-Wa,-march=armv7-a
 obj-$(CONFIG_SOC_IMX6) += suspend-imx6.o
 obj-$(CONFIG_SOC_IMX53) += suspend-imx53.o
 endif
+AFLAGS_resume-imx6.o :=-Wa,-march=armv7-a
+obj-$(CONFIG_SOC_IMX6) += resume-imx6.o
 obj-$(CONFIG_SOC_IMX6) += pm-imx6.o
 
 obj-$(CONFIG_SOC_IMX1) += mach-imx1.o

arch/arm/mach-imx/common.h

@@ -109,17 +109,17 @@ void imx_cpu_die(unsigned int cpu);
 int imx_cpu_kill(unsigned int cpu);
 
 #ifdef CONFIG_SUSPEND
-void v7_cpu_resume(void);
 void imx53_suspend(void __iomem *ocram_vbase);
 extern const u32 imx53_suspend_sz;
 void imx6_suspend(void __iomem *ocram_vbase);
 #else
-static inline void v7_cpu_resume(void) {}
 static inline void imx53_suspend(void __iomem *ocram_vbase) {}
 static const u32 imx53_suspend_sz;
 static inline void imx6_suspend(void __iomem *ocram_vbase) {}
 #endif
 
+void v7_cpu_resume(void);
+
 void imx6_pm_ccm_init(const char *ccm_compat);
 void imx6q_pm_init(void);
 void imx6dl_pm_init(void);

arch/arm/mach-imx/resume-imx6.S

+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ */
+
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+#include <asm/asm-offsets.h>
+#include <asm/hardware/cache-l2x0.h>
+#include "hardware.h"
+
+/*
+ * The following code must assume it is running from physical address
+ * where absolute virtual addresses to the data section have to be
+ * turned into relative ones.
+ */
+
+ENTRY(v7_cpu_resume)
+	bl	v7_invalidate_l1
+#ifdef CONFIG_CACHE_L2X0
+	bl	l2c310_early_resume
+#endif
+	b	cpu_resume
+ENDPROC(v7_cpu_resume)

arch/arm/mach-imx/suspend-imx6.S

@@ -327,17 +327,3 @@ resume:
 
 	ret	lr
 ENDPROC(imx6_suspend)
-
-/*
- * The following code must assume it is running from physical address
- * where absolute virtual addresses to the data section have to be
- * turned into relative ones.
- */
-
-ENTRY(v7_cpu_resume)
-	bl	v7_invalidate_l1
-#ifdef CONFIG_CACHE_L2X0
-	bl	l2c310_early_resume
-#endif
-	b	cpu_resume
-ENDPROC(v7_cpu_resume)

arch/arm64/boot/dts/freescale/imx8qxp-mek.dts

@@ -52,11 +52,6 @@ ethphy0: ethernet-phy@0 {
 			compatible = "ethernet-phy-ieee802.3-c22";
 			reg = <0>;
 		};
-
-		ethphy1: ethernet-phy@1 {
-			compatible = "ethernet-phy-ieee802.3-c22";
-			reg = <1>;
-		};
 	};
 };
 

drivers/firmware/imx/imx-scu.c

@@ -29,6 +29,7 @@ struct imx_sc_chan {
 	struct mbox_client cl;
 	struct mbox_chan *ch;
 	int idx;
+	struct completion tx_done;
 };
 
 struct imx_sc_ipc {
@@ -100,6 +101,14 @@ int imx_scu_get_handle(struct imx_sc_ipc **ipc)
 }
 EXPORT_SYMBOL(imx_scu_get_handle);
 
+/* Callback called when the word of a message is ack-ed, eg read by SCU */
+static void imx_scu_tx_done(struct mbox_client *cl, void *mssg, int r)
+{
+	struct imx_sc_chan *sc_chan = container_of(cl, struct imx_sc_chan, cl);
+
+	complete(&sc_chan->tx_done);
+}
+
 static void imx_scu_rx_callback(struct mbox_client *c, void *msg)
 {
 	struct imx_sc_chan *sc_chan = container_of(c, struct imx_sc_chan, cl);
@@ -149,6 +158,19 @@ static int imx_scu_ipc_write(struct imx_sc_ipc *sc_ipc, void *msg)
 
 	for (i = 0; i < hdr->size; i++) {
 		sc_chan = &sc_ipc->chans[i % 4];
+
+		/*
+		 * SCU requires that all messages words are written
+		 * sequentially but linux MU driver implements multiple
+		 * independent channels for each register so ordering between
+		 * different channels must be ensured by SCU API interface.
+		 *
+		 * Wait for tx_done before every send to ensure that no
+		 * queueing happens at the mailbox channel level.
+		 */
+		wait_for_completion(&sc_chan->tx_done);
+		reinit_completion(&sc_chan->tx_done);
+
 		ret = mbox_send_message(sc_chan->ch, &data[i]);
 		if (ret < 0)
 			return ret;
@@ -247,6 +269,11 @@ static int imx_scu_probe(struct platform_device *pdev)
 		cl->knows_txdone = true;
 		cl->rx_callback = imx_scu_rx_callback;
 
+		/* Initial tx_done completion as "done" */
+		cl->tx_done = imx_scu_tx_done;
+		init_completion(&sc_chan->tx_done);
+		complete(&sc_chan->tx_done);
+
 		sc_chan->sc_ipc = sc_ipc;
 		sc_chan->idx = i % 4;
 		sc_chan->ch = mbox_request_channel_byname(cl, chan_name);

drivers/firmware/imx/misc.c

@@ -16,7 +16,7 @@ struct imx_sc_msg_req_misc_set_ctrl {
 	u32 ctrl;
 	u32 val;
 	u16 resource;
-} __packed;
+} __packed __aligned(4);
 
 struct imx_sc_msg_req_cpu_start {
 	struct imx_sc_rpc_msg hdr;
@@ -24,18 +24,18 @@ struct imx_sc_msg_req_cpu_start {
 	u32 address_lo;
 	u16 resource;
 	u8 enable;
-} __packed;
+} __packed __aligned(4);
 
 struct imx_sc_msg_req_misc_get_ctrl {
 	struct imx_sc_rpc_msg hdr;
 	u32 ctrl;
 	u16 resource;
-} __packed;
+} __packed __aligned(4);
 
 struct imx_sc_msg_resp_misc_get_ctrl {
 	struct imx_sc_rpc_msg hdr;
 	u32 val;
-} __packed;
+} __packed __aligned(4);
 
 /*
  * This function sets a miscellaneous control value.

drivers/firmware/imx/scu-pd.c

@@ -61,7 +61,7 @@ struct imx_sc_msg_req_set_resource_power_mode {
 	struct imx_sc_rpc_msg hdr;
 	u16 resource;
 	u8 mode;
-} __packed;
+} __packed __aligned(4);
 
 #define IMX_SCU_PD_NAME_SIZE 20
 struct imx_sc_pm_domain {

drivers/soc/imx/soc-imx-scu.c

@@ -25,7 +25,7 @@ struct imx_sc_msg_misc_get_soc_id {
 			u32 id;
 		} resp;
 	} data;
-} __packed;
+} __packed __aligned(4);
 
 struct imx_sc_msg_misc_get_soc_uid {
 	struct imx_sc_rpc_msg hdr;