Merge tag 'v3.18-rockchip-dts2-v2' of...

Merge tag 'v3.18-rockchip-dts2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Merge "second bunch of dts changes for 3.18" from Heiko Stubner:

More peripheral support for Rockchip SoCs
- dwc2 usb controllers
- spi controllers
- emmc controller

* tag 'v3.18-rockchip-dts2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: Remove "regulator-always-on" in vcc_rmii for Radxa Rock
  ARM: dts: rockchip: fix rk3188 emmc pull references
  ARM: dts: rockchip: fix swapped Radxa Rock pinctrl references
  ARM: dts: rockchip: clean up rk3xxx mmc nodes
  ARM: dts: rockchip: add emmc nodes for rk3066 and rk3188
  ARM: dts: rockchip: add Cortex-A9 SPI controller nodes
  ARM: dts: rockchip: enable usb ports on Radxa Rock
  ARM: dts: rockchip: add dwc2 controllers for rk3066 and rk3188
  ARM: dts: rockchip: remove rockchip,bus-index from rk3xxx i2c0
  ARM: dts: Switch i2c0 to 400kHz on rk3288-evb-rk808
  ARM: dts: Add rk808 PMIC to rk3288-evb-rk808
  ARM: dts: Add mshc aliases for rk3288
  ARM: dts: Add SPI nodes to rk3288
  ARM: dts: Enable USB host1(dwc) on rk3288-evb
  ARM: dts: add rk3288 dwc2 controller support
  ARM: dts: Add sdio0 and sdio1 to the rk3288
Signed-off-by: Olof Johansson <olof@lixom.net>

arch/arm/boot/dts/rk3066a.dtsi

@@ -179,6 +179,27 @@ pcfg_pull_none: pcfg_pull_none {
 			bias-disable;
 		};
 
+		emmc {
+			emmc_clk: emmc-clk {
+				rockchip,pins = <RK_GPIO3 31 RK_FUNC_2 &pcfg_pull_default>;
+			};
+
+			emmc_cmd: emmc-cmd {
+				rockchip,pins = <RK_GPIO4 9 RK_FUNC_2 &pcfg_pull_default>;
+			};
+
+			emmc_rst: emmc-rst {
+				rockchip,pins = <RK_GPIO4 10 RK_FUNC_2 &pcfg_pull_default>;
+			};
+
+			/*
+			 * The data pins are shared between nandc and emmc and
+			 * not accessible through pinctrl. Also they should've
+			 * been already set correctly by firmware, as
+			 * flash/emmc is the boot-device.
+			 */
+		};
+
 		i2c0 {
 			i2c0_xfer: i2c0-xfer {
 				rockchip,pins = <RK_GPIO2 28 RK_FUNC_1 &pcfg_pull_none>,
@@ -238,6 +259,42 @@ pwm3_out: pwm3-out {
 			};
 		};
 
+		spi0 {
+			spi0_clk: spi0-clk {
+				rockchip,pins = <RK_GPIO1 5 RK_FUNC_2 &pcfg_pull_default>;
+			};
+			spi0_cs0: spi0-cs0 {
+				rockchip,pins = <RK_GPIO1 4 RK_FUNC_2 &pcfg_pull_default>;
+			};
+			spi0_tx: spi0-tx {
+				rockchip,pins = <RK_GPIO1 7 RK_FUNC_2 &pcfg_pull_default>;
+			};
+			spi0_rx: spi0-rx {
+				rockchip,pins = <RK_GPIO1 6 RK_FUNC_2 &pcfg_pull_default>;
+			};
+			spi0_cs1: spi0-cs1 {
+				rockchip,pins = <RK_GPIO4 15 RK_FUNC_1 &pcfg_pull_default>;
+			};
+		};
+
+		spi1 {
+			spi1_clk: spi1-clk {
+				rockchip,pins = <RK_GPIO2 19 RK_FUNC_2 &pcfg_pull_default>;
+			};
+			spi1_cs0: spi1-cs0 {
+				rockchip,pins = <RK_GPIO2 20 RK_FUNC_2 &pcfg_pull_default>;
+			};
+			spi1_rx: spi1-rx {
+				rockchip,pins = <RK_GPIO2 22 RK_FUNC_2 &pcfg_pull_default>;
+			};
+			spi1_tx: spi1-tx {
+				rockchip,pins = <RK_GPIO2 21 RK_FUNC_2 &pcfg_pull_default>;
+			};
+			spi1_cs1: spi1-cs1 {
+				rockchip,pins = <RK_GPIO2 23 RK_FUNC_2 &pcfg_pull_default>;
+			};
+		};
+
 		uart0 {
 			uart0_xfer: uart0-xfer {
 				rockchip,pins = <RK_GPIO1 0 RK_FUNC_1 &pcfg_pull_default>,
@@ -406,6 +463,16 @@ &pwm3 {
 	pinctrl-0 = <&pwm3_out>;
 };
 
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_clk &spi0_tx &spi0_rx &spi0_cs0>;
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_clk &spi1_tx &spi1_rx &spi1_cs0>;
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_xfer>;

arch/arm/boot/dts/rk3188-radxarock.dts

@@ -65,6 +65,19 @@ ir_recv: gpio-ir-receiver {
 		pinctrl-0 = <&ir_recv_pin>;
 	};
 
+	vcc_otg: usb-otg-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&otg_vbus_drv>;
+		regulator-name = "otg-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
 	vcc_sd0: sdmmc-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "sdmmc-supply";
@@ -74,6 +87,19 @@ vcc_sd0: sdmmc-regulator {
 		startup-delay-us = <100000>;
 		vin-supply = <&vcc_io>;
 	};
+
+	vcc_host: usb-host-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&host_vbus_drv>;
+		regulator-name = "host-pwr";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
 };
 
 &i2c1 {
@@ -160,7 +186,6 @@ vcc_rmii: REG9 {
 				regulator-name = "VCC_RMII";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
-				regulator-always-on;
 			};
 
 			vccio_wl: REG10 {
@@ -220,6 +245,15 @@ ir_recv_pin: ir-recv-pin {
 			rockchip,pins = <RK_GPIO0 10 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
+
+	usb {
+		host_vbus_drv: host-vbus-drv {
+			rockchip,pins = <0 3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+		otg_vbus_drv: otg-vbus-drv {
+			rockchip,pins = <2 31 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
 };
 
 &uart0 {
@@ -238,6 +272,14 @@ &uart3 {
 	status = "okay";
 };
 
+&usb_host {
+	status = "okay";
+};
+
+&usb_otg {
+	status = "okay";
+};
+
 &wdt {
 	status = "okay";
 };

arch/arm/boot/dts/rk3188.dtsi

@@ -147,6 +147,27 @@ pcfg_pull_none: pcfg_pull_none {
 			bias-disable;
 		};
 
+		emmc {
+			emmc_clk: emmc-clk {
+				rockchip,pins = <RK_GPIO0 24 RK_FUNC_2 &pcfg_pull_none>;
+			};
+
+			emmc_cmd: emmc-cmd {
+				rockchip,pins = <RK_GPIO0 26 RK_FUNC_2 &pcfg_pull_up>;
+			};
+
+			emmc_rst: emmc-rst {
+				rockchip,pins = <RK_GPIO0 27 RK_FUNC_2 &pcfg_pull_none>;
+			};
+
+			/*
+			 * The data pins are shared between nandc and emmc and
+			 * not accessible through pinctrl. Also they should've
+			 * been already set correctly by firmware, as
+			 * flash/emmc is the boot-device.
+			 */
+		};
+
 		i2c0 {
 			i2c0_xfer: i2c0-xfer {
 				rockchip,pins = <RK_GPIO1 24 RK_FUNC_1 &pcfg_pull_none>,
@@ -206,6 +227,42 @@ pwm3_out: pwm3-out {
 			};
 		};
 
+		spi0 {
+			spi0_clk: spi0-clk {
+				rockchip,pins = <RK_GPIO1 6 RK_FUNC_2 &pcfg_pull_up>;
+			};
+			spi0_cs0: spi0-cs0 {
+				rockchip,pins = <RK_GPIO1 7 RK_FUNC_2 &pcfg_pull_up>;
+			};
+			spi0_tx: spi0-tx {
+				rockchip,pins = <RK_GPIO1 5 RK_FUNC_2 &pcfg_pull_up>;
+			};
+			spi0_rx: spi0-rx {
+				rockchip,pins = <RK_GPIO1 4 RK_FUNC_2 &pcfg_pull_up>;
+			};
+			spi0_cs1: spi0-cs1 {
+				rockchip,pins = <RK_GPIO1 15 RK_FUNC_1 &pcfg_pull_up>;
+			};
+		};
+
+		spi1 {
+			spi1_clk: spi1-clk {
+				rockchip,pins = <RK_GPIO0 30 RK_FUNC_1 &pcfg_pull_up>;
+			};
+			spi1_cs0: spi1-cs0 {
+				rockchip,pins = <RK_GPIO0 31 RK_FUNC_1 &pcfg_pull_up>;
+			};
+			spi1_rx: spi1-rx {
+				rockchip,pins = <RK_GPIO0 28 RK_FUNC_1 &pcfg_pull_up>;
+			};
+			spi1_tx: spi1-tx {
+				rockchip,pins = <RK_GPIO0 29 RK_FUNC_1 &pcfg_pull_up>;
+			};
+			spi1_cs1: spi1-cs1 {
+				rockchip,pins = <RK_GPIO1 14 RK_FUNC_2 &pcfg_pull_up>;
+			};
+		};
+
 		uart0 {
 			uart0_xfer: uart0-xfer {
 				rockchip,pins = <RK_GPIO1 0 RK_FUNC_1 &pcfg_pull_up>,
@@ -381,6 +438,18 @@ &pwm3 {
 	pinctrl-0 = <&pwm3_out>;
 };
 
+&spi0 {
+	compatible = "rockchip,rk3188-spi", "rockchip,rk3066-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_clk &spi0_tx &spi0_rx &spi0_cs0>;
+};
+
+&spi1 {
+	compatible = "rockchip,rk3188-spi", "rockchip,rk3066-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_clk &spi1_tx &spi1_rx &spi1_cs0>;
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_xfer>;

arch/arm/boot/dts/rk3288-evb-rk808.dts

@@ -16,3 +16,135 @@
 / {
 	compatible = "rockchip,rk3288-evb-rk808", "rockchip,rk3288";
 };
+
+&i2c0 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	rk808: pmic@1b {
+		compatible = "rockchip,rk808";
+		reg = <0x1b>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int>;
+		rockchip,system-power-controller;
+		wakeup-source;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk808-clkout2";
+
+		vcc8-supply = <&vcc_18>;
+		vcc9-supply = <&vcc_io>;
+		vcc10-supply = <&vcc_io>;
+		vcc12-supply = <&vcc_io>;
+		vddio-supply = <&vccio_pmu>;
+
+		regulators {
+			vdd_cpu: DCDC_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-name = "vdd_arm";
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1250000>;
+				regulator-name = "vdd_gpu";
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_ddr";
+			};
+
+			vcc_io: DCDC_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_io";
+			};
+
+			vccio_pmu: LDO_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_pmu";
+			};
+
+			vcc_tp: LDO_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_tp";
+			};
+
+			vdd_10: LDO_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "vdd_10";
+			};
+
+			vcc18_lcd: LDO_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc18_lcd";
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_sd";
+			};
+
+			vdd10_lcd: LDO_REG6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "vdd10_lcd";
+			};
+
+			vcc_18: LDO_REG7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_18";
+			};
+
+			vcca_codec: LDO_REG8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcca_codec";
+			};
+
+			vcc_wl: SWITCH_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_wl";
+			};
+
+			vcc_lcd: SWITCH_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_lcd";
+			};
+		};
+	};
+};

arch/arm/boot/dts/rk3288-evb.dtsi

@@ -177,3 +177,7 @@ host_vbus_drv: host-vbus-drv {
 &usb_host0_ehci {
 	status = "okay";
 };
+
+&usb_host1 {
+	status = "okay";
+};

arch/arm/boot/dts/rk3288.dtsi

@@ -29,11 +29,18 @@ aliases {
 		i2c3 = &i2c3;
 		i2c4 = &i2c4;
 		i2c5 = &i2c5;
+		mshc0 = &emmc;
+		mshc1 = &sdmmc;
+		mshc2 = &sdio0;
+		mshc3 = &sdio1;
 		serial0 = &uart0;
 		serial1 = &uart1;
 		serial2 = &uart2;
 		serial3 = &uart3;
 		serial4 = &uart4;
+		spi0 = &spi0;
+		spi1 = &spi1;
+		spi2 = &spi2;
 	};
 
 	cpus {
@@ -126,6 +133,26 @@ sdmmc: dwmmc@ff0c0000 {
 		status = "disabled";
 	};
 
+	sdio0: dwmmc@ff0d0000 {
+		compatible = "rockchip,rk3288-dw-mshc";
+		clocks = <&cru HCLK_SDIO0>, <&cru SCLK_SDIO0>;
+		clock-names = "biu", "ciu";
+		fifo-depth = <0x100>;
+		interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+		reg = <0xff0d0000 0x4000>;
+		status = "disabled";
+	};
+
+	sdio1: dwmmc@ff0e0000 {
+		compatible = "rockchip,rk3288-dw-mshc";
+		clocks = <&cru HCLK_SDIO1>, <&cru SCLK_SDIO1>;
+		clock-names = "biu", "ciu";
+		fifo-depth = <0x100>;
+		interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+		reg = <0xff0e0000 0x4000>;
+		status = "disabled";
+	};
+
 	emmc: dwmmc@ff0f0000 {
 		compatible = "rockchip,rk3288-dw-mshc";
 		clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>;
@@ -146,6 +173,45 @@ saradc: saradc@ff100000 {
 		status = "disabled";
 	};
 
+	spi0: spi@ff110000 {
+		compatible = "rockchip,rk3288-spi", "rockchip,rk3066-spi";
+		clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>;
+		clock-names = "spiclk", "apb_pclk";
+		interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi0_clk &spi0_tx &spi0_rx &spi0_cs0>;
+		reg = <0xff110000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	spi1: spi@ff120000 {
+		compatible = "rockchip,rk3288-spi", "rockchip,rk3066-spi";
+		clocks = <&cru SCLK_SPI1>, <&cru PCLK_SPI1>;
+		clock-names = "spiclk", "apb_pclk";
+		interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi1_clk &spi1_tx &spi1_rx &spi1_cs0>;
+		reg = <0xff120000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	spi2: spi@ff130000 {
+		compatible = "rockchip,rk3288-spi", "rockchip,rk3066-spi";
+		clocks = <&cru SCLK_SPI2>, <&cru PCLK_SPI2>;
+		clock-names = "spiclk", "apb_pclk";
+		interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi2_clk &spi2_tx &spi2_rx &spi2_cs0>;
+		reg = <0xff130000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
 	i2c1: i2c@ff140000 {
 		compatible = "rockchip,rk3288-i2c";
 		reg = <0xff140000 0x1000>;
@@ -274,6 +340,26 @@ usb_host0_ehci: usb@ff500000 {
 
 	/* NOTE: ohci@ff520000 doesn't actually work on hardware */
 
+	usb_host1: usb@ff540000 {
+		compatible = "rockchip,rk3288-usb", "rockchip,rk3066-usb",
+				"snps,dwc2";
+		reg = <0xff540000 0x40000>;
+		interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_USBHOST1>;
+		clock-names = "otg";
+		status = "disabled";
+	};
+
+	usb_otg: usb@ff580000 {
+		compatible = "rockchip,rk3288-usb", "rockchip,rk3066-usb",
+				"snps,dwc2";
+		reg = <0xff580000 0x40000>;
+		interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_OTG0>;
+		clock-names = "otg";
+		status = "disabled";
+	};
+
 	usb_hsic: usb@ff5c0000 {
 		compatible = "generic-ehci";
 		reg = <0xff5c0000 0x100>;
@@ -600,6 +686,88 @@ sdmmc_bus4: sdmmc-bus4 {
 			};
 		};
 
+		sdio0 {
+			sdio0_bus1: sdio0-bus1 {
+				rockchip,pins = <4 20 RK_FUNC_1 &pcfg_pull_up>;
+			};
+
+			sdio0_bus4: sdio0-bus4 {
+				rockchip,pins = <4 20 RK_FUNC_1 &pcfg_pull_up>,
+						<4 21 RK_FUNC_1 &pcfg_pull_up>,
+						<4 22 RK_FUNC_1 &pcfg_pull_up>,
+						<4 23 RK_FUNC_1 &pcfg_pull_up>;
+			};
+
+			sdio0_cmd: sdio0-cmd {
+				rockchip,pins = <4 24 RK_FUNC_1 &pcfg_pull_up>;
+			};
+
+			sdio0_clk: sdio0-clk {
+				rockchip,pins = <4 25 RK_FUNC_1 &pcfg_pull_none>;
+			};
+
+			sdio0_cd: sdio0-cd {
+				rockchip,pins = <4 26 RK_FUNC_1 &pcfg_pull_up>;
+			};
+
+			sdio0_wp: sdio0-wp {
+				rockchip,pins = <4 27 RK_FUNC_1 &pcfg_pull_up>;
+			};
+
+			sdio0_pwr: sdio0-pwr {
+				rockchip,pins = <4 28 RK_FUNC_1 &pcfg_pull_up>;
+			};
+
+			sdio0_bkpwr: sdio0-bkpwr {
+				rockchip,pins = <4 29 RK_FUNC_1 &pcfg_pull_up>;
+			};
+
+			sdio0_int: sdio0-int {
+				rockchip,pins = <4 30 RK_FUNC_1 &pcfg_pull_up>;
+			};
+		};
+
+		sdio1 {
+			sdio1_bus1: sdio1-bus1 {
+				rockchip,pins = <3 24 4 &pcfg_pull_up>;
+			};
+
+			sdio1_bus4: sdio1-bus4 {
+				rockchip,pins = <3 24 4 &pcfg_pull_up>,
+						<3 25 4 &pcfg_pull_up>,
+						<3 26 4 &pcfg_pull_up>,
+						<3 27 4 &pcfg_pull_up>;
+			};
+
+			sdio1_cd: sdio1-cd {
+				rockchip,pins = <3 28 4 &pcfg_pull_up>;
+			};
+
+			sdio1_wp: sdio1-wp {
+				rockchip,pins = <3 29 4 &pcfg_pull_up>;
+			};
+
+			sdio1_bkpwr: sdio1-bkpwr {
+				rockchip,pins = <3 30 4 &pcfg_pull_up>;
+			};
+
+			sdio1_int: sdio1-int {
+				rockchip,pins = <3 31 4 &pcfg_pull_up>;
+			};
+
+			sdio1_cmd: sdio1-cmd {
+				rockchip,pins = <4 6 4 &pcfg_pull_up>;
+			};
+
+			sdio1_clk: sdio1-clk {
+				rockchip,pins = <4 7 4 &pcfg_pull_none>;
+			};
+
+			sdio1_pwr: sdio1-pwr {
+				rockchip,pins = <4 9 4 &pcfg_pull_up>;
+			};
+		};
+
 		emmc {
 			emmc_clk: emmc-clk {
 				rockchip,pins = <3 18 RK_FUNC_2 &pcfg_pull_none>;
@@ -636,6 +804,56 @@ emmc_bus8: emmc-bus8 {
 			};
 		};
 
+		spi0 {
+			spi0_clk: spi0-clk {
+				rockchip,pins = <5 12 RK_FUNC_1 &pcfg_pull_up>;
+			};
+			spi0_cs0: spi0-cs0 {
+				rockchip,pins = <5 13 RK_FUNC_1 &pcfg_pull_up>;
+			};
+			spi0_tx: spi0-tx {
+				rockchip,pins = <5 14 RK_FUNC_1 &pcfg_pull_up>;
+			};
+			spi0_rx: spi0-rx {
+				rockchip,pins = <5 15 RK_FUNC_1 &pcfg_pull_up>;
+			};
+			spi0_cs1: spi0-cs1 {
+				rockchip,pins = <5 16 RK_FUNC_1 &pcfg_pull_up>;
+			};
+		};
+		spi1 {
+			spi1_clk: spi1-clk {
+				rockchip,pins = <7 12 RK_FUNC_2 &pcfg_pull_up>;
+			};
+			spi1_cs0: spi1-cs0 {
+				rockchip,pins = <7 13 RK_FUNC_2 &pcfg_pull_up>;
+			};
+			spi1_rx: spi1-rx {
+				rockchip,pins = <7 14 RK_FUNC_2 &pcfg_pull_up>;
+			};
+			spi1_tx: spi1-tx {
+				rockchip,pins = <7 15 RK_FUNC_2 &pcfg_pull_up>;
+			};
+		};
+
+		spi2 {
+			spi2_cs1: spi2-cs1 {
+				rockchip,pins = <8 3 RK_FUNC_1 &pcfg_pull_up>;
+			};
+			spi2_clk: spi2-clk {
+				rockchip,pins = <8 6 RK_FUNC_1 &pcfg_pull_up>;
+			};
+			spi2_cs0: spi2-cs0 {
+				rockchip,pins = <8 7 RK_FUNC_1 &pcfg_pull_up>;
+			};
+			spi2_rx: spi2-rx {
+				rockchip,pins = <8 8 RK_FUNC_1 &pcfg_pull_up>;
+			};
+			spi2_tx: spi2-tx {
+				rockchip,pins = <8 9 RK_FUNC_1 &pcfg_pull_up>;
+			};
+		};
+
 		uart0 {
 			uart0_xfer: uart0-xfer {
 				rockchip,pins = <4 16 RK_FUNC_1 &pcfg_pull_up>,

arch/arm/boot/dts/rk3xxx.dtsi

@@ -26,6 +26,11 @@ aliases {
 		i2c2 = &i2c2;
 		i2c3 = &i2c3;
 		i2c4 = &i2c4;
+		mshc0 = &emmc;
+		mshc1 = &mmc0;
+		mshc2 = &mmc1;
+		spi0 = &spi0;
+		spi1 = &spi1;
 	};
 
 	amba {
@@ -129,12 +134,28 @@ uart1: serial@10126000 {
 		status = "disabled";
 	};
 
+	usb_otg: usb@10180000 {
+		compatible = "rockchip,rk3066-usb", "snps,dwc2";
+		reg = <0x10180000 0x40000>;
+		interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_OTG0>;
+		clock-names = "otg";
+		status = "disabled";
+	};
+
+	usb_host: usb@101c0000 {
+		compatible = "snps,dwc2";
+		reg = <0x101c0000 0x40000>;
+		interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_OTG1>;
+		clock-names = "otg";
+		status = "disabled";
+	};
+
 	mmc0: dwmmc@10214000 {
 		compatible = "rockchip,rk2928-dw-mshc";
 		reg = <0x10214000 0x1000>;
 		interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 
 		clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>;
 		clock-names = "biu", "ciu";
@@ -146,8 +167,6 @@ mmc1: dwmmc@10218000 {
 		compatible = "rockchip,rk2928-dw-mshc";
 		reg = <0x10218000 0x1000>;
 		interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 
 		clocks = <&cru HCLK_SDIO>, <&cru SCLK_SDIO>;
 		clock-names = "biu", "ciu";
@@ -155,6 +174,17 @@ mmc1: dwmmc@10218000 {
 		status = "disabled";
 	};
 
+	emmc: dwmmc@1021c000 {
+		compatible = "rockchip,rk2928-dw-mshc";
+		reg = <0x1021c000 0x1000>;
+		interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+
+		clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>;
+		clock-names = "biu", "ciu";
+
+		status = "disabled";
+	};
+
 	pmu: pmu@20004000 {
 		compatible = "rockchip,rk3066-pmu", "syscon";
 		reg = <0x20004000 0x100>;
@@ -173,7 +203,6 @@ i2c0: i2c@2002d000 {
 		#size-cells = <0>;
 
 		rockchip,grf = <&grf>;
-		rockchip,bus-index = <0>;
 
 		clock-names = "i2c";
 		clocks = <&cru PCLK_I2C0>;
@@ -312,4 +341,26 @@ saradc: saradc@2006c000 {
 		clock-names = "saradc", "apb_pclk";
 		status = "disabled";
 	};
+
+	spi0: spi@20070000 {
+		compatible = "rockchip,rk3066-spi";
+		clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>;
+		clock-names = "spiclk", "apb_pclk";
+		interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+		reg = <0x20070000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	spi1: spi@20074000 {
+		compatible = "rockchip,rk3066-spi";
+		clocks = <&cru SCLK_SPI1>, <&cru PCLK_SPI1>;
+		clock-names = "spiclk", "apb_pclk";
+		interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+		reg = <0x20074000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
 };