Merge tag 'hwmon-for-linus-v4.14' of...

Merge tag 'hwmon-for-linus-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:

 - new drivers:
   - Lantiq CPU temperature sensor
   - IBM CFF power supply
   - TPS53679 PMBus driver

 - new support:
   - LM5066I (lm25066 PMBus driver)
   - Intel VID protocol VR13 (PMBus drivers)
   - CAT34TS02C, GT30TS00, GT34TS02, and CAT34TS04 (jc42 driver)

 - cleanup and minor improvements in several drivers

* tag 'hwmon-for-linus-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (36 commits)
  hwmon: (ltq-cputemp) add cpu temp sensor driver
  hwmon: (ltq-cputemp) add devicetree bindings documentation
  hwmon: (pmbus) Add support for Texas Instruments tps53679 device
  hwmon: (asc7621) make several arrays static const
  hwmon: (pmbus/lm25066) Add support for TI LM5066I
  hwmon: (pmbus/lm25066) Offset coefficient depends on CL
  hwmon: (pmbus) Add support for Intel VID protocol VR13
  Documentation: hwmon: Document the IBM CFF power supply
  hwmon: (pmbus) Add IBM Common Form Factor (CFF) power supply driver
  dt-bindings: hwmon: Document the IBM CCF power supply version 1
  hwmon: (ftsteutates) constify i2c_device_id
  hwmon: da9052: Add support for TSI channel
  mfd: da9052: Make touchscreen registration optional
  hwmon: da9052: Replace S_IRUGO with 0444
  mfd: da9052: Add register details for TSI
  hwmon: (aspeed-pwm) add THERMAL dependency
  hwmon: (pmbus) Add debugfs for status registers
  hwmon: (aspeed-pwm-tacho) cooling device support.
  Documentation: dt-bindings: aspeed-pwm-tacho cooling device.
  hwmon: (pmbus): Add generic alarm bit for iin and pin
  ...

Documentation/devicetree/bindings/hwmon/aspeed-pwm-tacho.txt

@@ -11,6 +11,8 @@ Required properties for pwm-tacho node:
 
 - #size-cells : should be 1.
 
+- #cooling-cells: should be 2.
+
 - reg : address and length of the register set for the device.
 
 - pinctrl-names : a pinctrl state named "default" must be defined.
@@ -28,12 +30,17 @@ fan subnode format:
 Under fan subnode there can upto 8 child nodes, with each child node
 representing a fan. If there are 8 fans each fan can have one PWM port and
 one/two Fan tach inputs.
+For PWM port can be configured cooling-levels to create cooling device.
+Cooling device could be bound to a thermal zone for the thermal control.
 
 Required properties for each child node:
 - reg : should specify PWM source port.
 	integer value in the range 0 to 7 with 0 indicating PWM port A and
 	7 indicating PWM port H.
 
+- cooling-levels: PWM duty cycle values in a range from 0 to 255
+                  which correspond to thermal cooling states.
+
 - aspeed,fan-tach-ch : should specify the Fan tach input channel.
                 integer value in the range 0 through 15, with 0 indicating
 		Fan tach channel 0 and 15 indicating Fan tach channel 15.
@@ -50,6 +57,7 @@ pwm_tacho_fixed_clk: fixedclk {
 pwm_tacho: pwmtachocontroller@1e786000 {
 	#address-cells = <1>;
 	#size-cells = <1>;
+	#cooling-cells = <2>;
 	reg = <0x1E786000 0x1000>;
 	compatible = "aspeed,ast2500-pwm-tacho";
 	clocks = <&pwm_tacho_fixed_clk>;
@@ -58,6 +66,7 @@ pwm_tacho: pwmtachocontroller@1e786000 {
 
 	fan@0 {
 		reg = <0x00>;
+		cooling-levels = /bits/ 8 <125 151 177 203 229 255>;
 		aspeed,fan-tach-ch = /bits/ 8 <0x00>;
 	};
 

Documentation/devicetree/bindings/hwmon/ibm,cffps1.txt

+Device-tree bindings for IBM Common Form Factor Power Supply Version 1
+----------------------------------------------------------------------
+
+Required properties:
+ - compatible = "ibm,cffps1";
+ - reg = < I2C bus address >;		: Address of the power supply on the
+					  I2C bus.
+
+Example:
+
+    i2c-bus@100 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        #interrupt-cells = <1>;
+        < more properties >
+
+        power-supply@68 {
+            compatible = "ibm,cffps1";
+            reg = <0x68>;
+        };
+    };

Documentation/devicetree/bindings/hwmon/ltq-cputemp.txt

+Lantiq cpu temperatur sensor
+
+Requires node properties:
+- compatible value :
+	"lantiq,cputemp"
+
+Example:
+	cputemp@0 {
+		compatible = "lantiq,cputemp";
+	};

Documentation/hwmon/ftsteutates

@@ -18,6 +18,10 @@ enhancements. It can monitor up to 4 voltages, 16 temperatures and
 8 fans. It also contains an integrated watchdog which is currently
 implemented in this driver.
 
+To clear a temperature or fan alarm, execute the following command with the
+correct path to the alarm file:
+	echo 0 >XXXX_alarm
+
 Specification of the chip can be found here:
 ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Services/Software&Tools/Linux_SystemMonitoring&Watchdog&GPIO/BMC-Teutates_Specification_V1.21.pdf
 ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Services/Software&Tools/Linux_SystemMonitoring&Watchdog&GPIO/Fujitsu_mainboards-1-Sensors_HowTo-en-US.pdf

Documentation/hwmon/ibm-cffps

+Kernel driver ibm-cffps
+=======================
+
+Supported chips:
+  * IBM Common Form Factor power supply
+
+Author: Eddie James <eajames@us.ibm.com>
+
+Description
+-----------
+
+This driver supports IBM Common Form Factor (CFF) power supplies. This driver
+is a client to the core PMBus driver.
+
+Usage Notes
+-----------
+
+This driver does not auto-detect devices. You will have to instantiate the
+devices explicitly. Please see Documentation/i2c/instantiating-devices for
+details.
+
+Sysfs entries
+-------------
+
+The following attributes are supported:
+
+curr1_alarm		Output current over-current alarm.
+curr1_input		Measured output current in mA.
+curr1_label		"iout1"
+
+fan1_alarm		Fan 1 warning.
+fan1_fault		Fan 1 fault.
+fan1_input		Fan 1 speed in RPM.
+fan2_alarm		Fan 2 warning.
+fan2_fault		Fan 2 fault.
+fan2_input		Fan 2 speed in RPM.
+
+in1_alarm		Input voltage under-voltage alarm.
+in1_input		Measured input voltage in mV.
+in1_label		"vin"
+in2_alarm		Output voltage over-voltage alarm.
+in2_input		Measured output voltage in mV.
+in2_label		"vout1"
+
+power1_alarm		Input fault or alarm.
+power1_input		Measured input power in uW.
+power1_label		"pin"
+
+temp1_alarm		PSU inlet ambient temperature over-temperature alarm.
+temp1_input		Measured PSU inlet ambient temp in millidegrees C.
+temp2_alarm		Secondary rectifier temp over-temperature alarm.
+temp2_input		Measured secondary rectifier temp in millidegrees C.
+temp3_alarm		ORing FET temperature over-temperature alarm.
+temp3_input		Measured ORing FET temperature in millidegrees C.

Documentation/hwmon/lm25066

@@ -29,6 +29,11 @@ Supported chips:
     Addresses scanned: -
     Datasheet:
 	http://www.national.com/pf/LM/LM5066.html
+  * Texas Instruments LM5066I
+    Prefix: 'lm5066i'
+    Addresses scanned: -
+	Datasheet:
+    http://www.ti.com/product/LM5066I
 
 Author: Guenter Roeck <linux@roeck-us.net>
 
@@ -37,8 +42,8 @@ Description
 -----------
 
 This driver supports hardware monitoring for National Semiconductor / TI LM25056,
-LM25063, LM25066, LM5064, and LM5066 Power Management, Monitoring, Control, and
-Protection ICs.
+LM25063, LM25066, LM5064, and LM5066/LM5066I Power Management, Monitoring,
+Control, and Protection ICs.
 
 The driver is a client driver to the core PMBus driver. Please see
 Documentation/hwmon/pmbus for details on PMBus client drivers.

drivers/hwmon/Kconfig

@@ -343,6 +343,7 @@ config SENSORS_ASB100
 
 config SENSORS_ASPEED
 	tristate "ASPEED AST2400/AST2500 PWM and Fan tach driver"
+	depends on THERMAL || THERMAL=n
 	select REGMAP
 	help
 	  This driver provides support for ASPEED AST2400/AST2500 PWM
@@ -790,6 +791,13 @@ config SENSORS_LTC4261
 	  This driver can also be built as a module. If so, the module will
 	  be called ltc4261.
 
+config SENSORS_LTQ_CPUTEMP
+	bool "Lantiq cpu temperature sensor driver"
+	depends on LANTIQ
+	help
+	  If you say yes here you get support for the temperature
+	  sensor inside your CPU.
+
 config SENSORS_MAX1111
 	tristate "Maxim MAX1111 Serial 8-bit ADC chip and compatibles"
 	depends on SPI_MASTER

drivers/hwmon/Makefile

@@ -110,6 +110,7 @@ obj-$(CONFIG_SENSORS_LTC4222)	+= ltc4222.o
 obj-$(CONFIG_SENSORS_LTC4245)	+= ltc4245.o
 obj-$(CONFIG_SENSORS_LTC4260)	+= ltc4260.o
 obj-$(CONFIG_SENSORS_LTC4261)	+= ltc4261.o
+obj-$(CONFIG_SENSORS_LTQ_CPUTEMP) += ltq-cputemp.o
 obj-$(CONFIG_SENSORS_MAX1111)	+= max1111.o
 obj-$(CONFIG_SENSORS_MAX16065)	+= max16065.o
 obj-$(CONFIG_SENSORS_MAX1619)	+= max1619.o

drivers/hwmon/adc128d818.c

@@ -384,7 +384,7 @@ static struct attribute *adc128_attrs[] = {
 	NULL
 };
 
-static struct attribute_group adc128_group = {
+static const struct attribute_group adc128_group = {
 	.attrs = adc128_attrs,
 	.is_visible = adc128_is_visible,
 };

drivers/hwmon/ads1015.c

@@ -191,24 +191,23 @@ static int ads1015_get_channels_config_of(struct i2c_client *client)
 		unsigned int data_rate = ADS1015_DEFAULT_DATA_RATE;
 
 		if (of_property_read_u32(node, "reg", &pval)) {
-			dev_err(&client->dev, "invalid reg on %s\n",
-				node->full_name);
+			dev_err(&client->dev, "invalid reg on %pOF\n", node);
 			continue;
 		}
 
 		channel = pval;
 		if (channel >= ADS1015_CHANNELS) {
 			dev_err(&client->dev,
-				"invalid channel index %d on %s\n",
-				channel, node->full_name);
+				"invalid channel index %d on %pOF\n",
+				channel, node);
 			continue;
 		}
 
 		if (!of_property_read_u32(node, "ti,gain", &pval)) {
 			pga = pval;
 			if (pga > 6) {
-				dev_err(&client->dev, "invalid gain on %s\n",
-					node->full_name);
+				dev_err(&client->dev, "invalid gain on %pOF\n",
+					node);
 				return -EINVAL;
 			}
 		}
@@ -217,8 +216,7 @@ static int ads1015_get_channels_config_of(struct i2c_client *client)
 			data_rate = pval;
 			if (data_rate > 7) {
 				dev_err(&client->dev,
-					"invalid data_rate on %s\n",
-					node->full_name);
+					"invalid data_rate on %pOF\n", node);
 				return -EINVAL;
 			}
 		}

drivers/hwmon/adt7475.c

@@ -1319,14 +1319,14 @@ static struct attribute *vid_attrs[] = {
 	NULL
 };
 
-static struct attribute_group adt7475_attr_group = { .attrs = adt7475_attrs };
-static struct attribute_group fan4_attr_group = { .attrs = fan4_attrs };
-static struct attribute_group pwm2_attr_group = { .attrs = pwm2_attrs };
-static struct attribute_group in0_attr_group = { .attrs = in0_attrs };
-static struct attribute_group in3_attr_group = { .attrs = in3_attrs };
-static struct attribute_group in4_attr_group = { .attrs = in4_attrs };
-static struct attribute_group in5_attr_group = { .attrs = in5_attrs };
-static struct attribute_group vid_attr_group = { .attrs = vid_attrs };
+static const struct attribute_group adt7475_attr_group = { .attrs = adt7475_attrs };
+static const struct attribute_group fan4_attr_group = { .attrs = fan4_attrs };
+static const struct attribute_group pwm2_attr_group = { .attrs = pwm2_attrs };
+static const struct attribute_group in0_attr_group = { .attrs = in0_attrs };
+static const struct attribute_group in3_attr_group = { .attrs = in3_attrs };
+static const struct attribute_group in4_attr_group = { .attrs = in4_attrs };
+static const struct attribute_group in5_attr_group = { .attrs = in5_attrs };
+static const struct attribute_group vid_attr_group = { .attrs = vid_attrs };
 
 static int adt7475_detect(struct i2c_client *client,
 			  struct i2c_board_info *info)

drivers/hwmon/asc7621.c

@@ -512,7 +512,7 @@ static ssize_t show_pwm_ac(struct device *dev,
 {
 	SETUP_SHOW_DATA_PARAM(dev, attr);
 	u8 config, altbit, regval;
-	const u8 map[] = {
+	static const u8 map[] = {
 		0x01, 0x02, 0x04, 0x1f, 0x00, 0x06, 0x07, 0x10,
 		0x08, 0x0f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f
 	};
@@ -533,7 +533,7 @@ static ssize_t store_pwm_ac(struct device *dev,
 	SETUP_STORE_DATA_PARAM(dev, attr);
 	unsigned long reqval;
 	u8 currval, config, altbit, newval;
-	const u16 map[] = {
+	static const u16 map[] = {
 		0x04, 0x00, 0x01, 0xff, 0x02, 0xff, 0x05, 0x06,
 		0x08, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0x0f,
 		0x07, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,

drivers/hwmon/aspeed-pwm-tacho.c

@@ -20,6 +20,7 @@
 #include <linux/platform_device.h>
 #include <linux/sysfs.h>
 #include <linux/regmap.h>
+#include <linux/thermal.h>
 
 /* ASPEED PWM & FAN Tach Register Definition */
 #define ASPEED_PTCR_CTRL		0x00
@@ -166,6 +167,18 @@
 /* How long we sleep in us while waiting for an RPM result. */
 #define ASPEED_RPM_STATUS_SLEEP_USEC	500
 
+#define MAX_CDEV_NAME_LEN 16
+
+struct aspeed_cooling_device {
+	char name[16];
+	struct aspeed_pwm_tacho_data *priv;
+	struct thermal_cooling_device *tcdev;
+	int pwm_port;
+	u8 *cooling_levels;
+	u8 max_state;
+	u8 cur_state;
+};
+
 struct aspeed_pwm_tacho_data {
 	struct regmap *regmap;
 	unsigned long clk_freq;
@@ -180,6 +193,7 @@ struct aspeed_pwm_tacho_data {
 	u8 pwm_port_type[8];
 	u8 pwm_port_fan_ctrl[8];
 	u8 fan_tach_ch_source[16];
+	struct aspeed_cooling_device *cdev[8];
 	const struct attribute_group *groups[3];
 };
 
@@ -765,6 +779,94 @@ static void aspeed_create_fan_tach_channel(struct aspeed_pwm_tacho_data *priv,
 	}
 }
 
+static int
+aspeed_pwm_cz_get_max_state(struct thermal_cooling_device *tcdev,
+			    unsigned long *state)
+{
+	struct aspeed_cooling_device *cdev = tcdev->devdata;
+
+	*state = cdev->max_state;
+
+	return 0;
+}
+
+static int
+aspeed_pwm_cz_get_cur_state(struct thermal_cooling_device *tcdev,
+			    unsigned long *state)
+{
+	struct aspeed_cooling_device *cdev = tcdev->devdata;
+
+	*state = cdev->cur_state;
+
+	return 0;
+}
+
+static int
+aspeed_pwm_cz_set_cur_state(struct thermal_cooling_device *tcdev,
+			    unsigned long state)
+{
+	struct aspeed_cooling_device *cdev = tcdev->devdata;
+
+	if (state > cdev->max_state)
+		return -EINVAL;
+
+	cdev->cur_state = state;
+	cdev->priv->pwm_port_fan_ctrl[cdev->pwm_port] =
+					cdev->cooling_levels[cdev->cur_state];
+	aspeed_set_pwm_port_fan_ctrl(cdev->priv, cdev->pwm_port,
+				     cdev->cooling_levels[cdev->cur_state]);
+
+	return 0;
+}
+
+static const struct thermal_cooling_device_ops aspeed_pwm_cool_ops = {
+	.get_max_state = aspeed_pwm_cz_get_max_state,
+	.get_cur_state = aspeed_pwm_cz_get_cur_state,
+	.set_cur_state = aspeed_pwm_cz_set_cur_state,
+};
+
+static int aspeed_create_pwm_cooling(struct device *dev,
+				     struct device_node *child,
+				     struct aspeed_pwm_tacho_data *priv,
+				     u32 pwm_port, u8 num_levels)
+{
+	int ret;
+	struct aspeed_cooling_device *cdev;
+
+	cdev = devm_kzalloc(dev, sizeof(*cdev), GFP_KERNEL);
+
+	if (!cdev)
+		return -ENOMEM;
+
+	cdev->cooling_levels = devm_kzalloc(dev, num_levels, GFP_KERNEL);
+	if (!cdev->cooling_levels)
+		return -ENOMEM;
+
+	cdev->max_state = num_levels - 1;
+	ret = of_property_read_u8_array(child, "cooling-levels",
+					cdev->cooling_levels,
+					num_levels);
+	if (ret) {
+		dev_err(dev, "Property 'cooling-levels' cannot be read.\n");
+		return ret;
+	}
+	snprintf(cdev->name, MAX_CDEV_NAME_LEN, "%s%d", child->name, pwm_port);
+
+	cdev->tcdev = thermal_of_cooling_device_register(child,
+							 cdev->name,
+							 cdev,
+							 &aspeed_pwm_cool_ops);
+	if (IS_ERR(cdev->tcdev))
+		return PTR_ERR(cdev->tcdev);
+
+	cdev->priv = priv;
+	cdev->pwm_port = pwm_port;
+
+	priv->cdev[pwm_port] = cdev;
+
+	return 0;
+}
+
 static int aspeed_create_fan(struct device *dev,
 			     struct device_node *child,
 			     struct aspeed_pwm_tacho_data *priv)
@@ -778,6 +880,15 @@ static int aspeed_create_fan(struct device *dev,
 		return ret;
 	aspeed_create_pwm_port(priv, (u8)pwm_port);
 
+	ret = of_property_count_u8_elems(child, "cooling-levels");
+
+	if (ret > 0) {
+		ret = aspeed_create_pwm_cooling(dev, child, priv, pwm_port,
+						ret);
+		if (ret)
+			return ret;
+	}
+
 	count = of_property_count_u8_elems(child, "aspeed,fan-tach-ch");
 	if (count < 1)
 		return -EINVAL;
@@ -834,9 +945,10 @@ static int aspeed_pwm_tacho_probe(struct platform_device *pdev)
 
 	for_each_child_of_node(np, child) {
 		ret = aspeed_create_fan(dev, child, priv);
-		of_node_put(child);
-		if (ret)
+		if (ret) {
+			of_node_put(child);
 			return ret;
+		}
 	}
 
 	priv->groups[0] = &pwm_dev_group;

drivers/hwmon/ftsteutates.c

@@ -60,7 +60,7 @@
 
 static const unsigned short normal_i2c[] = { 0x73, I2C_CLIENT_END };
 
-static struct i2c_device_id fts_id[] = {
+static const struct i2c_device_id fts_id[] = {
 	{ "ftsteutates", 0 },
 	{ }
 };
@@ -435,6 +435,7 @@ clear_temp_alarm(struct device *dev, struct device_attribute *devattr,
 		goto error;
 
 	data->valid = false;
+	ret = count;
 error:
 	mutex_unlock(&data->update_lock);
 	return ret;
@@ -508,6 +509,7 @@ clear_fan_alarm(struct device *dev, struct device_attribute *devattr,
 		goto error;
 
 	data->valid = false;
+	ret = count;
 error:
 	mutex_unlock(&data->update_lock);
 	return ret;

drivers/hwmon/hwmon.c

@@ -85,7 +85,7 @@ static umode_t hwmon_dev_name_is_visible(struct kobject *kobj,
 	return attr->mode;
 }
 
-static struct attribute_group hwmon_dev_attr_group = {
+static const struct attribute_group hwmon_dev_attr_group = {
 	.attrs		= hwmon_dev_attrs,
 	.is_visible	= hwmon_dev_name_is_visible,
 };
@@ -135,7 +135,7 @@ static int hwmon_thermal_get_temp(void *data, int *temp)
 	return 0;
 }
 
-static struct thermal_zone_of_device_ops hwmon_thermal_ops = {
+static const struct thermal_zone_of_device_ops hwmon_thermal_ops = {
 	.get_temp = hwmon_thermal_get_temp,
 };
 

drivers/hwmon/i5k_amb.c

@@ -495,7 +495,7 @@ static struct {
 };
 
 #ifdef MODULE
-static struct pci_device_id i5k_amb_ids[] = {
+static const struct pci_device_id i5k_amb_ids[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_5000_ERR) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_5400_ERR) },
 	{ 0, }

drivers/hwmon/jc42.c

@@ -72,6 +72,8 @@ static const unsigned short normal_i2c[] = {
 #define NXP_MANID		0x1131  /* NXP Semiconductors */
 #define ONS_MANID		0x1b09  /* ON Semiconductor */
 #define STM_MANID		0x104a  /* ST Microelectronics */
+#define GT_MANID		0x1c68	/* Giantec */
+#define GT_MANID2		0x132d	/* Giantec, 2nd mfg ID */
 
 /* Supported chips */
 
@@ -86,6 +88,13 @@ static const unsigned short normal_i2c[] = {
 #define AT30TSE004_DEVID	0x2200
 #define AT30TSE004_DEVID_MASK	0xffff
 
+/* Giantec */
+#define GT30TS00_DEVID		0x2200
+#define GT30TS00_DEVID_MASK	0xff00
+
+#define GT34TS02_DEVID		0x3300
+#define GT34TS02_DEVID_MASK	0xff00
+
 /* IDT */
 #define TSE2004_DEVID		0x2200
 #define TSE2004_DEVID_MASK	0xff00
@@ -130,6 +139,12 @@ static const unsigned short normal_i2c[] = {
 #define CAT6095_DEVID		0x0800	/* Also matches CAT34TS02 */
 #define CAT6095_DEVID_MASK	0xffe0
 
+#define CAT34TS02C_DEVID	0x0a00
+#define CAT34TS02C_DEVID_MASK	0xfff0
+
+#define CAT34TS04_DEVID		0x2200
+#define CAT34TS04_DEVID_MASK	0xfff0
+
 /* ST Microelectronics */
 #define STTS424_DEVID		0x0101
 #define STTS424_DEVID_MASK	0xffff
@@ -158,6 +173,8 @@ static struct jc42_chips jc42_chips[] = {
 	{ ADT_MANID, ADT7408_DEVID, ADT7408_DEVID_MASK },
 	{ ATMEL_MANID, AT30TS00_DEVID, AT30TS00_DEVID_MASK },
 	{ ATMEL_MANID2, AT30TSE004_DEVID, AT30TSE004_DEVID_MASK },
+	{ GT_MANID, GT30TS00_DEVID, GT30TS00_DEVID_MASK },
+	{ GT_MANID2, GT34TS02_DEVID, GT34TS02_DEVID_MASK },
 	{ IDT_MANID, TSE2004_DEVID, TSE2004_DEVID_MASK },
 	{ IDT_MANID, TS3000_DEVID, TS3000_DEVID_MASK },
 	{ IDT_MANID, TS3001_DEVID, TS3001_DEVID_MASK },
@@ -170,6 +187,8 @@ static struct jc42_chips jc42_chips[] = {
 	{ MCP_MANID, MCP9843_DEVID, MCP9843_DEVID_MASK },
 	{ NXP_MANID, SE97_DEVID, SE97_DEVID_MASK },
 	{ ONS_MANID, CAT6095_DEVID, CAT6095_DEVID_MASK },
+	{ ONS_MANID, CAT34TS02C_DEVID, CAT34TS02C_DEVID_MASK },
+	{ ONS_MANID, CAT34TS04_DEVID, CAT34TS04_DEVID_MASK },
 	{ NXP_MANID, SE98_DEVID, SE98_DEVID_MASK },
 	{ STM_MANID, STTS424_DEVID, STTS424_DEVID_MASK },
 	{ STM_MANID, STTS424E_DEVID, STTS424E_DEVID_MASK },

drivers/hwmon/ltq-cputemp.c

+/* Lantiq cpu temperature sensor driver
+ *
+ * Copyright (C) 2017 Florian Eckert <fe@dev.tdt.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version
+ *
+ * This program is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see <http://www.gnu.org/licenses/>
+ */
+
+#include <linux/bitops.h>
+#include <linux/delay.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+
+#include <lantiq_soc.h>
+
+/* gphy1 configuration register contains cpu temperature */
+#define CGU_GPHY1_CR   0x0040
+#define CGU_TEMP_PD    BIT(19)
+
+static void ltq_cputemp_enable(void)
+{
+	ltq_cgu_w32(ltq_cgu_r32(CGU_GPHY1_CR) | CGU_TEMP_PD, CGU_GPHY1_CR);
+}
+
+static void ltq_cputemp_disable(void *data)
+{
+	ltq_cgu_w32(ltq_cgu_r32(CGU_GPHY1_CR) & ~CGU_TEMP_PD, CGU_GPHY1_CR);
+}
+
+static int ltq_read(struct device *dev, enum hwmon_sensor_types type,
+		    u32 attr, int channel, long *temp)
+{
+	int value;
+
+	switch (attr) {
+	case hwmon_temp_input:
+		/* get the temperature including one decimal place */
+		value = (ltq_cgu_r32(CGU_GPHY1_CR) >> 9) & 0x01FF;
+		value = value * 5;
+		/* range -38 to +154 °C, register value zero is -38.0 °C */
+		value -= 380;
+		/* scale temp to millidegree */
+		value = value * 100;
+		break;
+	default:
+		return -EOPNOTSUPP;
+	}
+
+	*temp = value;
+	return 0;
+}
+
+static umode_t ltq_is_visible(const void *_data, enum hwmon_sensor_types type,
+			      u32 attr, int channel)
+{
+	if (type != hwmon_temp)
+		return 0;
+
+	switch (attr) {
+	case hwmon_temp_input:
+		return 0444;
+	default:
+		return 0;
+	}
+}
+
+static const u32 ltq_chip_config[] = {
+	HWMON_C_REGISTER_TZ,
+	0
+};
+
+static const struct hwmon_channel_info ltq_chip = {
+	.type = hwmon_chip,
+	.config = ltq_chip_config,
+};
+
+static const u32 ltq_temp_config[] = {
+	HWMON_T_INPUT,
+	0
+};
+
+static const struct hwmon_channel_info ltq_temp = {
+	.type = hwmon_temp,
+	.config = ltq_temp_config,
+};
+
+static const struct hwmon_channel_info *ltq_info[] = {
+	&ltq_chip,
+	&ltq_temp,
+	NULL
+};
+
+static const struct hwmon_ops ltq_hwmon_ops = {
+	.is_visible = ltq_is_visible,
+	.read = ltq_read,
+};
+
+static const struct hwmon_chip_info ltq_chip_info = {
+	.ops = &ltq_hwmon_ops,
+	.info = ltq_info,
+};
+
+static int ltq_cputemp_probe(struct platform_device *pdev)
+{
+	struct device *hwmon_dev;
+	int err = 0;
+
+	/* available on vr9 v1.2 SoCs only */
+	if (ltq_soc_type() != SOC_TYPE_VR9_2)
+		return -ENODEV;
+
+	err = devm_add_action(&pdev->dev, ltq_cputemp_disable, NULL);
+	if (err)
+		return err;
+
+	ltq_cputemp_enable();
+
+	hwmon_dev = devm_hwmon_device_register_with_info(&pdev->dev,
+							 "ltq_cputemp",
+							 NULL,
+							 &ltq_chip_info,
+							 NULL);
+
+	if (IS_ERR(hwmon_dev)) {
+		dev_err(&pdev->dev, "Failed to register as hwmon device");
+		return PTR_ERR(hwmon_dev);
+	}
+
+	return 0;
+}
+
+const struct of_device_id ltq_cputemp_match[] = {
+	{ .compatible = "lantiq,cputemp" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, ltq_cputemp_match);
+
+static struct platform_driver ltq_cputemp_driver = {
+	.probe = ltq_cputemp_probe,
+	.driver = {
+		.name = "ltq-cputemp",
+		.of_match_table = ltq_cputemp_match,
+	},
+};
+
+module_platform_driver(ltq_cputemp_driver);
+
+MODULE_AUTHOR("Florian Eckert <fe@dev.tdt.de>");
+MODULE_DESCRIPTION("Lantiq cpu temperature sensor driver");
+MODULE_LICENSE("GPL");

drivers/hwmon/nct7802.c

@@ -704,7 +704,7 @@ static umode_t nct7802_temp_is_visible(struct kobject *kobj,
 	return attr->mode;
 }
 
-static struct attribute_group nct7802_temp_group = {
+static const struct attribute_group nct7802_temp_group = {
 	.attrs = nct7802_temp_attrs,
 	.is_visible = nct7802_temp_is_visible,
 };
@@ -802,7 +802,7 @@ static umode_t nct7802_in_is_visible(struct kobject *kobj,
 	return attr->mode;
 }
 
-static struct attribute_group nct7802_in_group = {
+static const struct attribute_group nct7802_in_group = {
 	.attrs = nct7802_in_attrs,
 	.is_visible = nct7802_in_is_visible,
 };
@@ -880,7 +880,7 @@ static umode_t nct7802_fan_is_visible(struct kobject *kobj,
 	return attr->mode;
 }
 
-static struct attribute_group nct7802_fan_group = {
+static const struct attribute_group nct7802_fan_group = {
 	.attrs = nct7802_fan_attrs,
 	.is_visible = nct7802_fan_is_visible,
 };
@@ -898,7 +898,7 @@ static struct attribute *nct7802_pwm_attrs[] = {
 	NULL
 };
 
-static struct attribute_group nct7802_pwm_group = {
+static const struct attribute_group nct7802_pwm_group = {
 	.attrs = nct7802_pwm_attrs,
 };
 
@@ -1011,7 +1011,7 @@ static struct attribute *nct7802_auto_point_attrs[] = {
 	NULL
 };
 
-static struct attribute_group nct7802_auto_point_group = {
+static const struct attribute_group nct7802_auto_point_group = {
 	.attrs = nct7802_auto_point_attrs,
 };
 

drivers/hwmon/pmbus/Kconfig

@@ -37,6 +37,15 @@ config SENSORS_ADM1275
 	  This driver can also be built as a module. If so, the module will
 	  be called adm1275.
 
+config SENSORS_IBM_CFFPS
+	tristate "IBM Common Form Factor Power Supply"
+	help
+	  If you say yes here you get hardware monitoring support for the IBM
+	  Common Form Factor power supply.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called ibm-cffps.
+
 config SENSORS_IR35221
 	tristate "Infineon IR35221"
 	default n
@@ -135,6 +144,15 @@ config SENSORS_TPS40422
 	  This driver can also be built as a module. If so, the module will
 	  be called tps40422.
 
+config SENSORS_TPS53679
+	tristate "TI TPS53679"
+	help
+	  If you say yes here you get hardware monitoring support for TI
+	  TPS53679.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called tps53679.
+
 config SENSORS_UCD9000
 	tristate "TI UCD90120, UCD90124, UCD90160, UCD9090, UCD90910"
 	default n

drivers/hwmon/pmbus/Makefile

@@ -5,6 +5,7 @@
 obj-$(CONFIG_PMBUS)		+= pmbus_core.o
 obj-$(CONFIG_SENSORS_PMBUS)	+= pmbus.o
 obj-$(CONFIG_SENSORS_ADM1275)	+= adm1275.o
+obj-$(CONFIG_SENSORS_IBM_CFFPS)	+= ibm-cffps.o
 obj-$(CONFIG_SENSORS_IR35221)	+= ir35221.o
 obj-$(CONFIG_SENSORS_LM25066)	+= lm25066.o
 obj-$(CONFIG_SENSORS_LTC2978)	+= ltc2978.o
@@ -14,6 +15,7 @@ obj-$(CONFIG_SENSORS_MAX20751)	+= max20751.o
 obj-$(CONFIG_SENSORS_MAX34440)	+= max34440.o
 obj-$(CONFIG_SENSORS_MAX8688)	+= max8688.o
 obj-$(CONFIG_SENSORS_TPS40422)	+= tps40422.o
+obj-$(CONFIG_SENSORS_TPS53679)	+= tps53679.o
 obj-$(CONFIG_SENSORS_UCD9000)	+= ucd9000.o
 obj-$(CONFIG_SENSORS_UCD9200)	+= ucd9200.o
 obj-$(CONFIG_SENSORS_ZL6100)	+= zl6100.o

drivers/hwmon/pmbus/ibm-cffps.c

+/*
+ * Copyright 2017 IBM Corp.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/bitops.h>
+#include <linux/device.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+
+#include "pmbus.h"
+
+/* STATUS_MFR_SPECIFIC bits */
+#define CFFPS_MFR_FAN_FAULT			BIT(0)
+#define CFFPS_MFR_THERMAL_FAULT			BIT(1)
+#define CFFPS_MFR_OV_FAULT			BIT(2)
+#define CFFPS_MFR_UV_FAULT			BIT(3)
+#define CFFPS_MFR_PS_KILL			BIT(4)
+#define CFFPS_MFR_OC_FAULT			BIT(5)
+#define CFFPS_MFR_VAUX_FAULT			BIT(6)
+#define CFFPS_MFR_CURRENT_SHARE_WARNING		BIT(7)
+
+static int ibm_cffps_read_byte_data(struct i2c_client *client, int page,
+				    int reg)
+{
+	int rc, mfr;
+
+	switch (reg) {
+	case PMBUS_STATUS_VOUT:
+	case PMBUS_STATUS_IOUT:
+	case PMBUS_STATUS_TEMPERATURE:
+	case PMBUS_STATUS_FAN_12:
+		rc = pmbus_read_byte_data(client, page, reg);
+		if (rc < 0)
+			return rc;
+
+		mfr = pmbus_read_byte_data(client, page,
+					   PMBUS_STATUS_MFR_SPECIFIC);
+		if (mfr < 0)
+			/*
+			 * Return the status register instead of an error,
+			 * since we successfully read status.
+			 */
+			return rc;
+
+		/* Add MFR_SPECIFIC bits to the standard pmbus status regs. */
+		if (reg == PMBUS_STATUS_FAN_12) {
+			if (mfr & CFFPS_MFR_FAN_FAULT)
+				rc |= PB_FAN_FAN1_FAULT;
+		} else if (reg == PMBUS_STATUS_TEMPERATURE) {
+			if (mfr & CFFPS_MFR_THERMAL_FAULT)
+				rc |= PB_TEMP_OT_FAULT;
+		} else if (reg == PMBUS_STATUS_VOUT) {
+			if (mfr & (CFFPS_MFR_OV_FAULT | CFFPS_MFR_VAUX_FAULT))
+				rc |= PB_VOLTAGE_OV_FAULT;
+			if (mfr & CFFPS_MFR_UV_FAULT)
+				rc |= PB_VOLTAGE_UV_FAULT;
+		} else if (reg == PMBUS_STATUS_IOUT) {
+			if (mfr & CFFPS_MFR_OC_FAULT)
+				rc |= PB_IOUT_OC_FAULT;
+			if (mfr & CFFPS_MFR_CURRENT_SHARE_WARNING)
+				rc |= PB_CURRENT_SHARE_FAULT;
+		}
+		break;
+	default:
+		rc = -ENODATA;
+		break;
+	}
+
+	return rc;
+}
+
+static int ibm_cffps_read_word_data(struct i2c_client *client, int page,
+				    int reg)
+{
+	int rc, mfr;
+
+	switch (reg) {
+	case PMBUS_STATUS_WORD:
+		rc = pmbus_read_word_data(client, page, reg);
+		if (rc < 0)
+			return rc;
+
+		mfr = pmbus_read_byte_data(client, page,
+					   PMBUS_STATUS_MFR_SPECIFIC);
+		if (mfr < 0)
+			/*
+			 * Return the status register instead of an error,
+			 * since we successfully read status.
+			 */
+			return rc;
+
+		if (mfr & CFFPS_MFR_PS_KILL)
+			rc |= PB_STATUS_OFF;
+		break;
+	default:
+		rc = -ENODATA;
+		break;
+	}
+
+	return rc;
+}
+
+static struct pmbus_driver_info ibm_cffps_info = {
+	.pages = 1,
+	.func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_IOUT |
+		PMBUS_HAVE_PIN | PMBUS_HAVE_FAN12 | PMBUS_HAVE_TEMP |
+		PMBUS_HAVE_TEMP2 | PMBUS_HAVE_TEMP3 | PMBUS_HAVE_STATUS_VOUT |
+		PMBUS_HAVE_STATUS_IOUT | PMBUS_HAVE_STATUS_INPUT |
+		PMBUS_HAVE_STATUS_TEMP | PMBUS_HAVE_STATUS_FAN12,
+	.read_byte_data = ibm_cffps_read_byte_data,
+	.read_word_data = ibm_cffps_read_word_data,
+};
+
+static int ibm_cffps_probe(struct i2c_client *client,
+			   const struct i2c_device_id *id)
+{
+	return pmbus_do_probe(client, id, &ibm_cffps_info);
+}
+
+static const struct i2c_device_id ibm_cffps_id[] = {
+	{ "ibm_cffps1", 1 },
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, ibm_cffps_id);
+
+static const struct of_device_id ibm_cffps_of_match[] = {
+	{ .compatible = "ibm,cffps1" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, ibm_cffps_of_match);
+
+static struct i2c_driver ibm_cffps_driver = {
+	.driver = {
+		.name = "ibm-cffps",
+		.of_match_table = ibm_cffps_of_match,
+	},
+	.probe = ibm_cffps_probe,
+	.remove = pmbus_do_remove,
+	.id_table = ibm_cffps_id,
+};
+
+module_i2c_driver(ibm_cffps_driver);
+
+MODULE_AUTHOR("Eddie James");
+MODULE_DESCRIPTION("PMBus driver for IBM Common Form Factor power supplies");
+MODULE_LICENSE("GPL");

drivers/hwmon/pmbus/lm25066.c

@@ -28,7 +28,7 @@
 #include <linux/i2c.h>
 #include "pmbus.h"
 
-enum chips { lm25056, lm25063, lm25066, lm5064, lm5066 };
+enum chips { lm25056, lm25063, lm25066, lm5064, lm5066, lm5066i };
 
 #define LM25066_READ_VAUX		0xd0
 #define LM25066_MFR_READ_IIN		0xd1
@@ -65,7 +65,7 @@ struct __coeff {
 #define PSC_CURRENT_IN_L	(PSC_NUM_CLASSES)
 #define PSC_POWER_L		(PSC_NUM_CLASSES + 1)
 
-static struct __coeff lm25066_coeff[5][PSC_NUM_CLASSES + 2] = {
+static struct __coeff lm25066_coeff[6][PSC_NUM_CLASSES + 2] = {
 	[lm25056] = {
 		[PSC_VOLTAGE_IN] = {
 			.m = 16296,
@@ -210,6 +210,41 @@ static struct __coeff lm25066_coeff[5][PSC_NUM_CLASSES + 2] = {
 			.m = 16,
 		},
 	},
+	[lm5066i] = {
+		[PSC_VOLTAGE_IN] = {
+			.m = 4617,
+			.b = -140,
+			.R = -2,
+		},
+		[PSC_VOLTAGE_OUT] = {
+			.m = 4602,
+			.b = 500,
+			.R = -2,
+		},
+		[PSC_CURRENT_IN] = {
+			.m = 15076,
+			.b = -504,
+			.R = -2,
+		},
+		[PSC_CURRENT_IN_L] = {
+			.m = 7645,
+			.b = 100,
+			.R = -2,
+		},
+		[PSC_POWER] = {
+			.m = 1701,
+			.b = -4000,
+			.R = -3,
+		},
+		[PSC_POWER_L] = {
+			.m = 861,
+			.b = -965,
+			.R = -3,
+		},
+		[PSC_TEMPERATURE] = {
+			.m = 16,
+		},
+	},
 };
 
 struct lm25066_data {
@@ -250,6 +285,7 @@ static int lm25066_read_word_data(struct i2c_client *client, int page, int reg)
 			ret = DIV_ROUND_CLOSEST(ret * 70, 453);
 			break;
 		case lm5066:
+		case lm5066i:
 			/* VIN: 2.18 mV VAUX: 725 uV LSB */
 			ret = DIV_ROUND_CLOSEST(ret * 725, 2180);
 			break;
@@ -488,16 +524,18 @@ static int lm25066_probe(struct i2c_client *client,
 	info->m[PSC_VOLTAGE_OUT] = coeff[PSC_VOLTAGE_OUT].m;
 	info->b[PSC_VOLTAGE_OUT] = coeff[PSC_VOLTAGE_OUT].b;
 	info->R[PSC_VOLTAGE_OUT] = coeff[PSC_VOLTAGE_OUT].R;
-	info->b[PSC_CURRENT_IN] = coeff[PSC_CURRENT_IN].b;
 	info->R[PSC_CURRENT_IN] = coeff[PSC_CURRENT_IN].R;
-	info->b[PSC_POWER] = coeff[PSC_POWER].b;
 	info->R[PSC_POWER] = coeff[PSC_POWER].R;
 	if (config & LM25066_DEV_SETUP_CL) {
 		info->m[PSC_CURRENT_IN] = coeff[PSC_CURRENT_IN_L].m;
+		info->b[PSC_CURRENT_IN] = coeff[PSC_CURRENT_IN_L].b;
 		info->m[PSC_POWER] = coeff[PSC_POWER_L].m;
+		info->b[PSC_POWER] = coeff[PSC_POWER_L].b;
 	} else {
 		info->m[PSC_CURRENT_IN] = coeff[PSC_CURRENT_IN].m;
+		info->b[PSC_CURRENT_IN] = coeff[PSC_CURRENT_IN].b;
 		info->m[PSC_POWER] = coeff[PSC_POWER].m;
+		info->b[PSC_POWER] = coeff[PSC_POWER].b;
 	}
 
 	return pmbus_do_probe(client, id, info);
@@ -509,6 +547,7 @@ static const struct i2c_device_id lm25066_id[] = {
 	{"lm25066", lm25066},
 	{"lm5064", lm5064},
 	{"lm5066", lm5066},
+	{"lm5066i", lm5066i},
 	{ }
 };
 

drivers/hwmon/pmbus/pmbus.h

@@ -341,7 +341,7 @@ enum pmbus_sensor_classes {
 #define PMBUS_HAVE_STATUS_VMON	BIT(19)
 
 enum pmbus_data_format { linear = 0, direct, vid };
-enum vrm_version { vr11 = 0, vr12 };
+enum vrm_version { vr11 = 0, vr12, vr13 };
 
 struct pmbus_driver_info {
 	int pages;		/* Total number of pages */

drivers/hwmon/pmbus/tps53679.c

+/*
+ * Hardware monitoring driver for Texas Instruments TPS53679
+ *
+ * Copyright (c) 2017 Mellanox Technologies. All rights reserved.
+ * Copyright (c) 2017 Vadim Pasternak <vadimp@mellanox.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include "pmbus.h"
+
+#define TPS53679_PROT_VR12_5MV		0x01 /* VR12.0 mode, 5-mV DAC */
+#define TPS53679_PROT_VR12_5_10MV	0x02 /* VR12.5 mode, 10-mV DAC */
+#define TPS53679_PROT_VR13_10MV		0x04 /* VR13.0 mode, 10-mV DAC */
+#define TPS53679_PROT_IMVP8_5MV		0x05 /* IMVP8 mode, 5-mV DAC */
+#define TPS53679_PROT_VR13_5MV		0x07 /* VR13.0 mode, 5-mV DAC */
+#define TPS53679_PAGE_NUM		2
+
+static int tps53679_identify(struct i2c_client *client,
+			     struct pmbus_driver_info *info)
+{
+	u8 vout_params;
+	int ret;
+
+	/* Read the register with VOUT scaling value.*/
+	ret = pmbus_read_byte_data(client, 0, PMBUS_VOUT_MODE);
+	if (ret < 0)
+		return ret;
+
+	vout_params = ret & GENMASK(4, 0);
+
+	switch (vout_params) {
+	case TPS53679_PROT_VR13_10MV:
+	case TPS53679_PROT_VR12_5_10MV:
+		info->vrm_version = vr13;
+		break;
+	case TPS53679_PROT_VR13_5MV:
+	case TPS53679_PROT_VR12_5MV:
+	case TPS53679_PROT_IMVP8_5MV:
+		info->vrm_version = vr12;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static struct pmbus_driver_info tps53679_info = {
+	.pages = TPS53679_PAGE_NUM,
+	.format[PSC_VOLTAGE_IN] = linear,
+	.format[PSC_VOLTAGE_OUT] = vid,
+	.format[PSC_TEMPERATURE] = linear,
+	.format[PSC_CURRENT_OUT] = linear,
+	.format[PSC_POWER] = linear,
+	.func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+		PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+		PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP |
+		PMBUS_HAVE_POUT,
+	.func[1] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT |
+		PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT |
+		PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP |
+		PMBUS_HAVE_POUT,
+	.identify = tps53679_identify,
+};
+
+static int tps53679_probe(struct i2c_client *client,
+			  const struct i2c_device_id *id)
+{
+	return pmbus_do_probe(client, id, &tps53679_info);
+}
+
+static const struct i2c_device_id tps53679_id[] = {
+	{"tps53679", 0},
+	{}
+};
+
+MODULE_DEVICE_TABLE(i2c, tps53679_id);
+
+static const struct of_device_id tps53679_of_match[] = {
+	{.compatible = "ti,tps53679"},
+	{}
+};
+MODULE_DEVICE_TABLE(of, tps53679_of_match);
+
+static struct i2c_driver tps53679_driver = {
+	.driver = {
+		.name = "tps53679",
+		.of_match_table = of_match_ptr(tps53679_of_match),
+	},
+	.probe = tps53679_probe,
+	.remove = pmbus_do_remove,
+	.id_table = tps53679_id,
+};
+
+module_i2c_driver(tps53679_driver);
+
+MODULE_AUTHOR("Vadim Pasternak <vadimp@mellanox.com>");
+MODULE_DESCRIPTION("PMBus driver for Texas Instruments TPS53679");
+MODULE_LICENSE("GPL");

drivers/hwmon/scpi-hwmon.c

@@ -120,7 +120,7 @@ scpi_show_label(struct device *dev, struct device_attribute *attr, char *buf)
 	return sprintf(buf, "%s\n", sensor->info.name);
 }
 
-static struct thermal_zone_of_device_ops scpi_sensor_ops = {
+static const struct thermal_zone_of_device_ops scpi_sensor_ops = {
 	.get_temp = scpi_read_temp,
 };
 

drivers/hwmon/stts751.c

@@ -718,6 +718,10 @@ static int stts751_read_chip_config(struct stts751_priv *priv)
 	ret = i2c_smbus_read_byte_data(priv->client, STTS751_REG_RATE);
 	if (ret < 0)
 		return ret;
+	if (ret >= ARRAY_SIZE(stts751_intervals)) {
+		dev_err(priv->dev, "Unrecognized conversion rate 0x%x\n", ret);
+		return -ENODEV;
+	}
 	priv->interval = ret;
 
 	ret = stts751_read_reg16(priv, &priv->event_max,

drivers/mfd/da9052-core.c

@@ -18,6 +18,7 @@
 #include <linux/mfd/core.h>
 #include <linux/slab.h>
 #include <linux/module.h>
+#include <linux/property.h>
 
 #include <linux/mfd/da9052/da9052.h>
 #include <linux/mfd/da9052/pdata.h>
@@ -518,9 +519,6 @@ static const struct mfd_cell da9052_subdev_info[] = {
 	{
 		.name = "da9052-wled3",
 	},
-	{
-		.name = "da9052-tsi",
-	},
 	{
 		.name = "da9052-bat",
 	},
@@ -529,6 +527,10 @@ static const struct mfd_cell da9052_subdev_info[] = {
 	},
 };
 
+static const struct mfd_cell da9052_tsi_subdev_info[] = {
+	{ .name = "da9052-tsi" },
+};
+
 const struct regmap_config da9052_regmap_config = {
 	.reg_bits = 8,
 	.val_bits = 8,
@@ -619,9 +621,27 @@ int da9052_device_init(struct da9052 *da9052, u8 chip_id)
 		goto err;
 	}
 
+	/*
+	 * Check if touchscreen pins are used are analogue input instead
+	 * of having a touchscreen connected to them. The analogue input
+	 * functionality will be provided by hwmon driver (if enabled).
+	 */
+	if (!device_property_read_bool(da9052->dev, "dlg,tsi-as-adc")) {
+		ret = mfd_add_devices(da9052->dev, PLATFORM_DEVID_AUTO,
+				      da9052_tsi_subdev_info,
+				      ARRAY_SIZE(da9052_tsi_subdev_info),
+				      NULL, 0, NULL);
+		if (ret) {
+			dev_err(da9052->dev, "failed to add TSI subdev: %d\n",
+				ret);
+			goto err;
+		}
+	}
+
 	return 0;
 
 err:
+	mfd_remove_devices(da9052->dev);
 	da9052_irq_exit(da9052);
 
 	return ret;

include/linux/mfd/da9052/da9052.h

@@ -45,6 +45,12 @@
 #define DA9052_ADC_TJUNC	8
 #define DA9052_ADC_VBBAT	9
 
+/* TSI channel has its own 4 channel mux */
+#define DA9052_ADC_TSI_XP	70
+#define DA9052_ADC_TSI_XN	71
+#define DA9052_ADC_TSI_YP	72
+#define DA9052_ADC_TSI_YN	73
+
 #define DA9052_IRQ_DCIN	0
 #define DA9052_IRQ_VBUS	1
 #define DA9052_IRQ_DCINREM	2

include/linux/mfd/da9052/reg.h

@@ -690,7 +690,10 @@
 /* TSI CONTROL REGISTER B BITS */
 #define DA9052_TSICONTB_ADCREF		0X80
 #define DA9052_TSICONTB_TSIMAN		0X40
-#define DA9052_TSICONTB_TSIMUX		0X30
+#define DA9052_TSICONTB_TSIMUX_XP	0X00
+#define DA9052_TSICONTB_TSIMUX_YP	0X10
+#define DA9052_TSICONTB_TSIMUX_XN	0X20
+#define DA9052_TSICONTB_TSIMUX_YN	0X30
 #define DA9052_TSICONTB_TSISEL3	0X08
 #define DA9052_TSICONTB_TSISEL2	0X04
 #define DA9052_TSICONTB_TSISEL1	0X02
@@ -705,8 +708,14 @@
 /* TSI CO-ORDINATE LSB RESULT REGISTER BITS */
 #define DA9052_TSILSB_PENDOWN		0X40
 #define DA9052_TSILSB_TSIZL		0X30
+#define DA9052_TSILSB_TSIZL_SHIFT	4
+#define DA9052_TSILSB_TSIZL_BITS	2
 #define DA9052_TSILSB_TSIYL		0X0C
+#define DA9052_TSILSB_TSIYL_SHIFT	2
+#define DA9052_TSILSB_TSIYL_BITS	2
 #define DA9052_TSILSB_TSIXL		0X03
+#define DA9052_TSILSB_TSIXL_SHIFT	0
+#define DA9052_TSILSB_TSIXL_BITS	2
 
 /* TSI Z MEASUREMENT MSB RESULT REGISTER BIT */
 #define DA9052_TSIZMSB_TSIZM		0XFF