[ARM] pxa: use new pin configuration mechanism for mainstone

1. the following code to configure PGSRx is no way portable and
   intuitive:

-	PGSR0 = 0x00008800;
-       PGSR1 = 0x00000002;
-       PGSR2 = 0x0001FC00;
-       PGSR3 = 0x00001F81;

   this is removed as low power state has already been encoded in
   the pin configuration definitions.

   Note: there is no specific reason for some of the GPIOs to drive
   high in low power mode as indicated by the above setting, those
   bits are ignored, and the result is validated to work.

2. the following code to configure GPIO wakeup is removed as this
   is now totally handled by pxa2xx_mfp_config():

-       PWER  = 0xC0000002;
-       PRER  = 0x00000002;
-       PFER  = 0x00000002;
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

arch/arm/mach-pxa/mainstone.c

@@ -40,7 +40,7 @@
 
 #include <asm/arch/pxa-regs.h>
 #include <asm/arch/pxa2xx-regs.h>
-#include <asm/arch/pxa2xx-gpio.h>
+#include <asm/arch/mfp-pxa27x.h>
 #include <asm/arch/mainstone.h>
 #include <asm/arch/audio.h>
 #include <asm/arch/pxafb.h>
@@ -51,6 +51,81 @@
 #include "generic.h"
 #include "devices.h"
 
+static unsigned long mainstone_pin_config[] = {
+	/* Chip Select */
+	GPIO15_nCS_1,
+
+	/* LCD - 16bpp Active TFT */
+	GPIO58_LCD_LDD_0,
+	GPIO59_LCD_LDD_1,
+	GPIO60_LCD_LDD_2,
+	GPIO61_LCD_LDD_3,
+	GPIO62_LCD_LDD_4,
+	GPIO63_LCD_LDD_5,
+	GPIO64_LCD_LDD_6,
+	GPIO65_LCD_LDD_7,
+	GPIO66_LCD_LDD_8,
+	GPIO67_LCD_LDD_9,
+	GPIO68_LCD_LDD_10,
+	GPIO69_LCD_LDD_11,
+	GPIO70_LCD_LDD_12,
+	GPIO71_LCD_LDD_13,
+	GPIO72_LCD_LDD_14,
+	GPIO73_LCD_LDD_15,
+	GPIO74_LCD_FCLK,
+	GPIO75_LCD_LCLK,
+	GPIO76_LCD_PCLK,
+	GPIO77_LCD_BIAS,
+	GPIO16_PWM0_OUT,	/* Backlight */
+
+	/* MMC */
+	GPIO32_MMC_CLK,
+	GPIO112_MMC_CMD,
+	GPIO92_MMC_DAT_0,
+	GPIO109_MMC_DAT_1,
+	GPIO110_MMC_DAT_2,
+	GPIO111_MMC_DAT_3,
+
+	/* USB Host Port 1 */
+	GPIO88_USBH1_PWR,
+	GPIO89_USBH1_PEN,
+
+	/* PC Card */
+	GPIO48_nPOE,
+	GPIO49_nPWE,
+	GPIO50_nPIOR,
+	GPIO51_nPIOW,
+	GPIO85_nPCE_1,
+	GPIO54_nPCE_2,
+	GPIO79_PSKTSEL,
+	GPIO55_nPREG,
+	GPIO56_nPWAIT,
+	GPIO57_nIOIS16,
+
+	/* AC97 */
+	GPIO45_AC97_SYSCLK,
+
+	/* Keypad */
+	GPIO93_KP_DKIN_0	| WAKEUP_ON_LEVEL_HIGH,
+	GPIO94_KP_DKIN_1	| WAKEUP_ON_LEVEL_HIGH,
+	GPIO95_KP_DKIN_2	| WAKEUP_ON_LEVEL_HIGH,
+	GPIO100_KP_MKIN_0	| WAKEUP_ON_LEVEL_HIGH,
+	GPIO101_KP_MKIN_1	| WAKEUP_ON_LEVEL_HIGH,
+	GPIO102_KP_MKIN_2	| WAKEUP_ON_LEVEL_HIGH,
+	GPIO97_KP_MKIN_3	| WAKEUP_ON_LEVEL_HIGH,
+	GPIO98_KP_MKIN_4	| WAKEUP_ON_LEVEL_HIGH,
+	GPIO99_KP_MKIN_5	| WAKEUP_ON_LEVEL_HIGH,
+	GPIO103_KP_MKOUT_0,
+	GPIO104_KP_MKOUT_1,
+	GPIO105_KP_MKOUT_2,
+	GPIO106_KP_MKOUT_3,
+	GPIO107_KP_MKOUT_4,
+	GPIO108_KP_MKOUT_5,
+	GPIO96_KP_MKOUT_6,
+
+	/* GPIO */
+	GPIO1_GPIO | WAKEUP_ON_EDGE_BOTH,
+};
 
 static unsigned long mainstone_irq_enabled;
 
@@ -279,13 +354,13 @@ static int mainstone_backlight_update_status(struct backlight_device *bl)
 	    bl->props.fb_blank != FB_BLANK_UNBLANK)
 		brightness = 0;
 
-	if (brightness != 0) {
-		pxa_gpio_mode(GPIO16_PWM0_MD);
+	if (brightness != 0)
 		pxa_set_cken(CKEN_PWM0, 1);
-	}
+
 	PWM_CTRL0 = 0;
 	PWM_PWDUTY0 = brightness;
 	PWM_PERVAL0 = bl->props.max_brightness;
+
 	if (brightness == 0)
 		pxa_set_cken(CKEN_PWM0, 0);
 	return 0; /* pointless return value */
@@ -363,16 +438,6 @@ static int mainstone_mci_init(struct device *dev, irq_handler_t mstone_detect_in
 {
 	int err;
 
-	/*
-	 * setup GPIO for PXA27x MMC controller
-	 */
-	pxa_gpio_mode(GPIO32_MMCCLK_MD);
-	pxa_gpio_mode(GPIO112_MMCCMD_MD);
-	pxa_gpio_mode(GPIO92_MMCDAT0_MD);
-	pxa_gpio_mode(GPIO109_MMCDAT1_MD);
-	pxa_gpio_mode(GPIO110_MMCDAT2_MD);
-	pxa_gpio_mode(GPIO111_MMCDAT3_MD);
-
 	/* make sure SD/Memory Stick multiplexer's signals
 	 * are routed to MMC controller
 	 */
@@ -444,10 +509,6 @@ static struct platform_device *platform_devices[] __initdata = {
 
 static int mainstone_ohci_init(struct device *dev)
 {
-	/* setup Port1 GPIO pin. */
-	pxa_gpio_mode( 88 | GPIO_ALT_FN_1_IN);	/* USBHPWR1 */
-	pxa_gpio_mode( 89 | GPIO_ALT_FN_2_OUT);	/* USBHPEN1 */
-
 	/* Set the Power Control Polarity Low and Power Sense
 	   Polarity Low to active low. */
 	UHCHR = (UHCHR | UHCHR_PCPL | UHCHR_PSPL) &
@@ -465,6 +526,8 @@ static void __init mainstone_init(void)
 {
 	int SW7 = 0;  /* FIXME: get from SCR (Mst doc section 3.2.1.1) */
 
+	pxa2xx_mfp_config(ARRAY_AND_SIZE(mainstone_pin_config));
+
 	mst_flash_data[0].width = (BOOT_DEF & 1) ? 2 : 4;
 	mst_flash_data[1].width = 4;
 
@@ -481,31 +544,6 @@ static void __init mainstone_init(void)
 	 */
 	ARB_CNTRL = ARB_CORE_PARK | 0x234;
 
-	/*
-	 * On Mainstone, we route AC97_SYSCLK via GPIO45 to
-	 * the audio daughter card
-	 */
-	pxa_gpio_mode(GPIO45_SYSCLK_AC97_MD);
-
-	GPSR(GPIO48_nPOE) =
-		GPIO_bit(GPIO48_nPOE) |
-		GPIO_bit(GPIO49_nPWE) |
-		GPIO_bit(GPIO50_nPIOR) |
-		GPIO_bit(GPIO51_nPIOW) |
-		GPIO_bit(GPIO85_nPCE_1) |
-		GPIO_bit(GPIO54_nPCE_2);
-
-	pxa_gpio_mode(GPIO48_nPOE_MD);
-	pxa_gpio_mode(GPIO49_nPWE_MD);
-	pxa_gpio_mode(GPIO50_nPIOR_MD);
-	pxa_gpio_mode(GPIO51_nPIOW_MD);
-	pxa_gpio_mode(GPIO85_nPCE_1_MD);
-	pxa_gpio_mode(GPIO54_nPCE_2_MD);
-	pxa_gpio_mode(GPIO79_pSKTSEL_MD);
-	pxa_gpio_mode(GPIO55_nPREG_MD);
-	pxa_gpio_mode(GPIO56_nPWAIT_MD);
-	pxa_gpio_mode(GPIO57_nIOIS16_MD);
-
 	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
 
 	/* reading Mainstone's "Virtual Configuration Register"
@@ -538,23 +576,9 @@ static void __init mainstone_map_io(void)
 	pxa_map_io();
 	iotable_init(mainstone_io_desc, ARRAY_SIZE(mainstone_io_desc));
 
-	/* initialize sleep mode regs (wake-up sources, etc) */
-	PGSR0 = 0x00008800;
-	PGSR1 = 0x00000002;
-	PGSR2 = 0x0001FC00;
-	PGSR3 = 0x00001F81;
-	PWER  = 0xC0000002;
-	PRER  = 0x00000002;
-	PFER  = 0x00000002;
  	/*	for use I SRAM as framebuffer.	*/
  	PSLR |= 0xF04;
  	PCFR = 0x66;
- 	/*	For Keypad wakeup.	*/
- 	KPC &=~KPC_ASACT;
- 	KPC |=KPC_AS;
- 	PKWR  = 0x000FD000;
- 	/*	Need read PKWR back after set it.	*/
- 	PKWR;
 }
 
 MACHINE_START(MAINSTONE, "Intel HCDDBBVA0 Development Platform (aka Mainstone)")