This adds the gpu nodes for the adreno 200 GPU on iMX51 and iMX53, now
supported by the freedreno driver.

The compatible for the iMX51 uses a patchid of 1, which is used by drm/msm
driver to identify the smaller 128KiB GMEM size.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add accelerometer sensor mma8451 support on i2c1 bus.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add magnetometer sensor mag3110 support on i2c3 bus.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add isl29023 light sensor support on i2c3 bus, the light
sensor's power is controlled by a fixed regulator, since
the isl29023 driver and most of other sensors on same
board like mag3110 and mma8451 do NOT support regulator
operation currently, they are all controlled by this
regulator, so this patch also adds the fixed regulator
support and make it always on.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

It is not recommended to place regulators inside "simple-bus", so move
them out to make it cleaner the addition of new regulators.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Boards based on imx6qdl have duplicate memory nodes:
- One coming from the board device tree file: memory@
- One coming from the imx6qdl.dtsi file.

Fix the duplication by removing the memory node from
the imx6qdl.dtsi file and by adding 'device_type = "memory";'
in the board Device Tree.

Converted using the following command:
perl -p0777i -e 's/memory\@10000000 \{\n/memory\@10000000 \{\n\t\tdevice_type = \"memory\";\n/m' `find ./arch/arm/boot/dts -name "imx6*"``
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add a memory node, with an empty memory size, which will be filled
by the bootloader.

This is done in preparation for removing the memory node from
imx6qdl.dtsi.
Reported-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx53-voipac-dmm-668 has two memory nodes, but the correct representation
would be to use a single one with two reg entries - one for each RAM chip
select, so fix it accordingly.
Reported-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

On the vf610-zii-scu4-aib board there is a hi8435 (32-channel
discrete-to-digital SPI sensor device) in the DSPI0 bus.

Add support for it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add egalax touch screen support on i2c2 bus, it is connected
to LVDS0, while the existing one on i2c3 bus is connected to
LVDS1.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add stop-mode property which is required by stop mode wakeup
feature.
Signed-off-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add stop-mode property which is required by stop mode wakeup
feature.
Signed-off-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add stop-mode property which is required by stop mode wakeup
feature.
Signed-off-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add stop-mode property which is required by stop mode wakeup
feature.
Signed-off-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The imx6ul-pico-pi contains a imx6ul-pico SoM and a pi baseboard:
https://www.technexion.com/products/pico-baseboards/detail/PICO-PI

Add support for it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds following peripherals support:

 - ADC
 - GPIO LED
 - GPIOs
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use the same child led node and label name as used in the
imx7d-pico-hobbit board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx6ul-pico-hobbit board contains:

- One SoM board (imx6ul pico)
- One base board (hobbit).

In order to make it easier for adding support for other board variants,
move the commom SoM part to the imx6ul-pico.dtsi file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

add the qDMA device tree nodes for LS1021A devices.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Boards based on vf500/vf600 have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the vf500.dtsi/vf610m4.dtsi files.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The GIC_CPU_MASK_SIMPLE() macro should take as its argument the actual
number of CPU cores the interrupt controller is wired to.

i.MX7S contains a single Cortex-A7, hence the second interrupt specifier
cell for Private Peripheral Interrupts should use "GIC_CPU_MASK_SIMPLE(1)".

Likewise, i.MX7D contains two Cortex-A7 cores, so it should use
"GIC_CPU_MASK_SIMPLE(2)" instead.

Tested on a imx7s-warp.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The GIC_CPU_MASK_SIMPLE() macro should take as its argument the actual
number of CPU cores the interrupt controller is wired to.

i.MX6UL contains a single Cortex-A7, hence the second interrupt specifier
cell for Private Peripheral Interrupts should use "GIC_CPU_MASK_SIMPLE(1)".

Tested on a imx6ul-evk.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The flexcan1 is pin conflict with fec. User would make flexcan1 enabled
with fec disabled to use CAN.
Signed-off-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The CAN transceiver on MX6SX Sabreauto board seems in sleep mode by default
after power up the board. User has to press the wakeup key on ARD baseboard
before using the transceiver, or it may not work properly when power up the
board at the first time(warm reset does not have such issue).

This patch operates the wake pin too besides stby/en pins by chaining them
together in regulator mode.
Signed-off-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

CAN transceiver is different on RevA and RevB board.
It's active high on RevA while active low on Rev B.
Signed-off-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The LS1021A has 8 possible PWMs, so adding them (disabled by default)
Signed-off-by: Patrick Havelange <patrick.havelange@essensium.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The ConnectCore 6UL SBC Pro has an AUO/Goodix LCD accessory kit that is
connected on the LVDS interface through an on-board LVDS transceiver.

This change adds support for the touch interface.
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This change adds support for the AUO G101EVN010 lcdif panel for the
mxsfb DRM driver.
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Boards based on imx25 have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx25.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Boards based on imx27 have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx27.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Boards based on imx1 have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx1.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Boards based on imx28 have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx28.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Boards based on imx23 have duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx23.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management.

Most of the i.MX NXP reference board dts files have already been
converted, so switch the remaining ones.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management.

Most of the wandboard dts files have already been converted, so switch
the remaining ones.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx50-evk has duplicate memory nodes:

- One coming from the board dts file: memory@

- One coming from the imx50.dtsi file.

Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX6SLL EVK board has WDOG_B pin connected to the PMIC;

Add the WDOG_B pinctrl entry and 'fsl,ext-reset-output'
property to wdog node to let watchdog trigger a system
POR reset via the PMIC.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>