VHT can be used with IBSS without needing any additional changes in
mac80211_hwsim, so start claiming support for this to increase test
coverage.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Previously, this was done only for Beacon frames, but similar timestamp
update is needed for Probe Response frames to make these more accurately
match the real IEEE 802.11 behavior. Previously, all zeros timestamp was
sent in Probe Response frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

While it was possible to create an IBSS with 80+80 MHz channel, joining
such an IBSS resulted in falling back to 20 MHz channel with VHT
disabled due to a missing switch case for 80+80.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The same piece of code appears at two places. Make a function from it.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Jouni found a bug in the remain-on-channel logic: when a short item
is queued, a long item is combined with it extending the original
one, and then the long item is deleted, the timeout doesn't go back
to the short one, and the short item ends up taking a long time. In
this case, this showed as blocking scan when running two test cases
back to back - the scan from the second was delayed even though all
the remain-on-channel items should long have been gone.

Fixing this with the current data structures turns out to be a bit
complicated, we just remove the long item from the dependents list
right now and don't recalculate the timeouts.

There's a somewhat similar bug where we delete the short item and
all the dependents go with it; to fix this we'd have to move them
from the dependents to the real list.

Instead of trying to do that, rewrite the code to not have all this
complexity in the data structures: use a single list and allow more
than one entry in it being marked as started. This makes the code a
bit more complex, the worker needs to understand that it might need
to just remove one of the started items, while keeping the device
off-channel, but that's not more complicated than the nested data
structures.

This then fixes both issues described, and makes it easier to also
limit the overall off-channel time when combining.

TODO: as before, with hardware remain-on-channel, deleting an item
after combining results in cancelling them all - we can keep track
of the time elapsed and only cancel after that to fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Typically drivers that implement hardware remain-on-channel will
have to wait for scheduling constraints, so make hwsim also wait
a little bit (only 20ms) before actually starting the operation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since the cookie is assigned inside ieee80211_make_ack_skb()
now, we no longer need to return the ack_skb as the cookie
and can simplify the function's return and the callers. Also
rename it to ieee80211_attach_ack_skb() to more accurately
reflect its purpose.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This is quite a bit of code that logically depends here since
it has to deal with all the remain-on-channel logic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If a mgmt-tx operation is aborted before it runs, the wrong
cookie is reported back to userspace, and the ack_skb gets
leaked since the frame is freed directly instead of freeing
it using ieee80211_free_txskb(). Fix that.

Fixes: 3b79af97 ("mac80211: stop using pointers as userspace cookies")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If some code stops the queues more times than having started
(for when refcounting is used), warn on and reset the counter
to 0 to avoid blocking forever.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

We need to free all skbs here, not just the one we peeked
from the list.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When freeing the TX skb for an off-channel TX, use the correct
API to also free the ACK skb that might have been allocated.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This reverts commit 45bb780a,
the previous two patches fixed the functionality.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When a new station is added to AP/GO interfaces the default behaviour
is for it to be added authenticated and associated, due to backwards
compatibility. To prevent that, the driver must be able to do that
(setting the NL80211_FEATURE_FULL_AP_CLIENT_STATE feature flag) and
userspace must set the flag mask to auth|assoc and clear the set.

Handle this quirk in the API entirely in nl80211, and always push the
full flags to the drivers. NL80211_FEATURE_FULL_AP_CLIENT_STATE is
still required for userspace to be allowed to set the mask including
those bits, but after checking that add both flags to the mask and
set in case userspace didn't set them otherwise.

This obsoletes the mac80211 code handling this difference, no other
driver is currently using these flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Fix nl80211_set_station() to use the value of NL80211_ATTR_STA_AID
attribute instead of NL80211_ATTR_PEER_AID attribute.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This commit adds implementation for abort scan in mac80211.
Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com>
Signed-off-by: Sunil Dutt <usdutt@qti.qualcomm.com>
[adjust to wdev change in previous patch and clean up code a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Implement new functionality for aborting an ongoing scan.

Add NL80211_CMD_ABORT_SCAN to the nl80211 interface. After
aborting the scan, driver shall provide the scan status by
calling cfg80211_scan_done().
Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com>
Signed-off-by: Sunil Dutt <usdutt@qti.qualcomm.com>
[change command to take wdev instead of netdev so that it
 can be used on p2p-device scans]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add new VIF flag, that will allow get NOA update
notification when driver will request this, even
this is not pure P2P vif (eg. STA vif).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

We had another change to fix this in mac80211, but the hwsim
"hardware" scan should also be fixed. Obviously this one isn't
important since it's not real hardware, but we'd better be
consistent.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Last caller of this function was removed in 3.17 in commit
97dc94f1.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

add ieee80211_iter_keys_rcu() to iterate over uploaded
keys in atomic context (when rcu is locked)

The station removal code removes the keys only after
calling synchronize_net(), so it's not safe to iterate
the keys at this point (and postponing the actual key
deletion with call_rcu() might result in some
badly-ordered ops calls).

Add a flag to indicate a station is being removed,
and skip the configured keys if it's set.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This can happen when the driver needs to send less frames
than expected and then needs to close the SP.
Mac80211 still needs to set the more_data properly based
on its buffer state (ps_tx_buffer and buffered frames on
other TIDs).
To that end, refactor the code that delivers frames upon
uAPSD trigger frames to be able to get only the more_data
bit without actually delivering those frames in case the
driver is just asking to set a NDP with EOSP and MORE_DATA
bit properly set.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In this attribute's documentation, it was not clear whether the delay
started counting when WoWLAN net-detect was enabled or when the system
was suspended.  The correct answer is that it starts when the system
suspends (which is when, in practice, the scan is scheduled).  Clarify
that in the nl80211.h documentation.
Suggested-by: Samuel Tan <samueltan@google.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This really should never happen except very early in the process
of bringing up a new driver, at which point you'll have to add
more debugging in the driver and this string isn't useful. Remove
it and save some size (when it's even compiled in.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This indicates a driver key selection issue, but even then there's
no point in printing it all the time, so ratelimit it. Also remove
the priv pointer from it -- people debugging will only have a single
device anyway and it's useless as anything but a cookie.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There's no point in printing the mpath pointer since it can't
be used for anything - print the MAC address instead (like in
the forwarding case.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The function is a very simple wrapper around another one,
just adds a few default parameters, so replace it with a
static inline instead of using EXPORT_SYMBOL, reducing
the module size slightly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Complete the tracepoint with the missing data - it's not printed
by default (a lot of it is dynamic arrays) but will be recorded
and be available during post-processing.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add missing tracing for:

1. start_radar_detection()
2. set_mcast_rates()
3. set_coalesce()
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Some devices or drivers cannot deal with having the same station
address for different virtual interfaces, say as a client to two
virtual AP interfaces. Rather than requiring each driver with a
limitation like that to enforce it, add a hardware flag for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

I want to get the full off-channel bugfix since later code depends on
it, as well as the AP client state change so I can revert it correctly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In the last change here, I neglected to update the cookie in one code
path: when a mgmt-tx has no real cookie sent to userspace as it doesn't
wait for a response, but is off-channel. The original code used the SKB
pointer as the cookie and always assigned the cookie to the TX SKB in
ieee80211_start_roc_work(), but my change turned this around and made
the code rely on a valid cookie being passed in.

Unfortunately, the off-channel no-wait TX path wasn't assigning one at
all, resulting in an uninitialized stack value being used. This wasn't
handed back to userspace as a cookie (since in the no-wait case there
isn't a cookie), but it was tested for non-zero to distinguish between
mgmt-tx and off-channel.

Fix this by assigning a dummy non-zero cookie unconditionally, and get
rid of a misleading comment and some dead code while at it. I'll clean
up the ACK SKB handling separately later.

Fixes: 3b79af97 ("mac80211: stop using pointers as userspace cookies")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

DFS channels should not be actively scanned as we can't be sure
if we are allowed or not.

If the current channel is in the DFS band, active scan might be
performed after CSA, but we have no guarantee about other channels,
therefore it is safer to prevent active scanning at all.

Cc: stable@vger.kernel.org
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Interfaces are being initialized (setup) on addition,
and torn down on removal.

However, p2p device is being torn down when stopped,
resulting in the next p2p start operation being done
on uninitialized interface.

Solve it by calling ieee80211_teardown_sdata() only
on interface removal (for the non-netdev case).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[squashed in fix to call teardown after unregister]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Geert Uytterhoeven says:

====================
sh_eth: Remove obsolete platform_device_id entries

Since commit 3d7608e4 ("ARM: shmobile: bockw: remove legacy
board file and config"), which is in v4.4-rc1, shmobile SoCs are only
supported in generic DT-only ARM multi-platform builds.  The sh_eth
driver doesn't need to match platform devices by name anymore, hence
this series removes the corresponding platform_device_id entries.

Changes since v2:
  - More Acks,
  - Platform dependency has entered mainline,

Changes since v1:
  - Protect some data and functions by #ifdef CONFIG_OF to silence
    unused compiler warnings on SH,
  - New patches 3 and 4.

Thanks for applying!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 3d7608e4 ("ARM: shmobile: bockw: remove legacy
board file and config"), R-Car Gen1 SoCs are only supported in generic
DT-only ARM multi-platform builds.  The driver doesn't need to match
platform devices by name anymore, hence remove the corresponding
platform_device_id entry.

Protect sh_eth_set_rate_r8a777x() and r8a777x_data by #ifdef CONFIG_OF,
as they're now referenced on DT platforms only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 1fa59bda ("ARM: shmobile: Remove legacy board code
for Armadillo-800 EVA"), r8a7740 is only supported in generic DT-only
ARM multi-platform builds.  The driver doesn't need to match platform
devices by name anymore, hence remove the corresponding
platform_device_id entry.

Protect r8a7740_data by #ifdef CONFIG_OF as it's now referenced on DT
platforms only. Move it to a more logical position, in front of the
r8a777x support, so we can have a single #ifdef covering all r7s* and
r8a* support soon. This requires moving a few helper functions, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit a483dcbf ("ARM: shmobile: lager: Remove legacy
board support"), R-Car Gen2 SoCs are only supported in generic DT-only
ARM multi-platform builds.  The driver doesn't need to match platform
devices by name anymore, hence remove the corresponding
platform_device_id entry.

Protect r8a779x_data by #ifdef CONFIG_OF as it's now referenced on DT
platforms only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>