Merge tag 'imx-defconfig-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/defconfig

i.MX defconfig update for 5.10:

- Enable i.MX6SLL, i.MX7ULP SoC and CAAM crypto driver support in
  multi_v7_defconfig.
- Enable the eLCDIF and Raydium RM67191 driver in arm64 defconfig to
  support MIPI DSI on imx8mq-evk.
- Enable NWL DSI host controller, dphy and SITRONIX ST7703 panel driver
  in arm64 defconfig to support display on imx8mq-librem5-devkit.
- Enable sl28cpld board management controller driver support in arm64
  defconfig.
- Enable i.MX8M SoCs support in imx_v6_v7_defconfig as they can run in
  AArch32 mode.

* tag 'imx-defconfig-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  arm64: defconfig: enable the sl28cpld board management controller
  arm64: defconfig: Enable the eLCDIF and Raydium RM67191 drivers
  arm64: defconfig: Enable imx8mq-librem5-devkit display stack
  arm64: defconfig: re-sync DRM related defconfig bits
  ARM: imx_v6_v7_defconfig: Support i.MX8MN/P/Q
  ARM: multi_v7_defconfig: Enable i.MX7ULP SoC
  ARM: multi_v7_defconfig: Enable i.MX6SLL SoC
  ARM: multi_v7_defconfig: enable caam crypto module

Link: https://lore.kernel.org/r/20200923073009.23678-6-shawnguo@kernel.orgSigned-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v5.10/defconfig-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/defconfig

Defconfig changes for omaps for v5.10 merge window

Enable twl4030_madc as a loadable module as the ADC is used
on some devices by the battery charger. And enable more widely
used networking options as loadable modules where possible.

* tag 'omap-for-v5.10/defconfig-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: omap2plus_defconfig: enable generic net options
  ARM: omap2plus_defconfig: enable twl4030_madc as a loadable module

Link: https://lore.kernel.org/r/pull-1601445968-476435@atomide.com-3Signed-off-by: Olof Johansson <olof@lixom.net>

This patch adds FMC2 EBI controller support used by STM32MP SOCs.

Link: https://lore.kernel.org/r/20200924101342.4707-1-alexandre.torgue@st.comSigned-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'samsung-defconfig-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/defconfig

Samsung defconfig changes for v5.10

1. Re-enable platform media drivers as new dependency on
   MEDIA_PLATFORM_SUPPORT appeared.
2. Enable ROHM BD718x7 PMIC present on some of boards with i.MX 8 SoCs.
3. Enable Samsung S3FWRN5 NFC driver present on TM2/TM2E boards.

* tag 'samsung-defconfig-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  arm64: defconfig: Enable Samsung S3FWRN5 NFC driver
  arm64: defconfig: Enable clock driver for ROHM BD718x7 PMIC
  ARM: exynos_defconfig: enable platform media drivers

Link: https://lore.kernel.org/r/20200920160705.9651-2-krzk@kernel.orgSigned-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'tegra-for-5.10-arm64-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/defconfig

arm64: tegra: Default configuration updates for v5.10-rc1

This pair of patches enable the ADMA, ACONNECT and AHUB drivers that
are required for audio support on Tegra210 and later.

* tag 'tegra-for-5.10-arm64-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  arm64: defconfig: Build ADMA and ACONNECT driver
  arm64: defconfig: Build AHUB component drivers

Link: https://lore.kernel.org/r/20200918150303.3938852-6-thierry.reding@gmail.comSigned-off-by: Olof Johansson <olof@lixom.net>

Enable the kernel modules for the board management controller "sl28cpld"
which is used on the SMARC-sAL28 board.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Select the eLCDIF display controller and Raydium RM67191 panel drivers,
so that MIPI DSI can be functional by default on a imx8mq-evk board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Merge tag 'aspeed-5.10-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into arm/defconfig

ASPEED defconfig updates for 5.10

 - Fix an issue with unwanted media drivers being enabled

 - New driver: IBM OP Panel, used on ast2600 systems. This requires
   enabling I2C slave mode

 - Enable I2C MUX GPIO driver

* tag 'aspeed-5.10-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
  ARM: config: aspeed_g5: Enable IBM OP Panel driver
  ARM: config: aspeed-g5: Enable I2C GPIO mux driver
  ARM: config: aspeed: Fix selection of media drivers

Link: https://lore.kernel.org/r/CACPK8XdFE2K1_cyrg=uaD6CaOm_p0RCRmjAsu6uyFKD4rnDggQ@mail.gmail.comSigned-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-arm-defconfig-for-v5.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/defconfig

Renesas ARM defconfig updates for v5.10

  - Enable touchscreen support on the iWave RZ/G1E platform,
  - Update for PCIE_RCAR => CONFIG_PCIE_RCAR_{HOST,EP} split, including
    enabling the latter,
  - Enable FLASH support on various R-Car Gen3 boards,
  - Refresh shmobile_defconfig for v5.9-rc1.

* tag 'renesas-arm-defconfig-for-v5.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
  ARM: shmobile: defconfig: Enable CONFIG_PCIE_RCAR_HOST
  ARM: multi_v7_defconfig: Enable CONFIG_PCIE_RCAR_HOST
  arm64: defconfig: Enable RPC-IF support
  ARM: shmobile: defconfig: Refresh for v5.9-rc1
  arm64: defconfig: Enable R-Car PCIe endpoint driver
  ARM: shmobile: defconfig: Enable TOUCHSCREEN_STMPE

Link: https://lore.kernel.org/r/20200904114819.30254-2-geert+renesas@glider.beSigned-off-by: Olof Johansson <olof@lixom.net>

Update the Integrator defconfig to the changes from the recent
kernel cycles and especially the v5.9-rc1 changes.

- Move options around as a result of Kconfig changes.
- Drop the ZBOOT_ROM* stuff that doesn't exist anymore.
- Add the syscon LEDs as used on the board for heartbeat
  and MMC traffic indication.
- Add fixed voltage regulator support, this is used by the
  MMC controller for card voltage.
- Select CONFIG_DRM_DISPLAY_CONNECTOR=y, the
  CONFIG_DRM_SIMPLE_BRIDGE was renamed when renaming the
  driver, but the simple bridge requires another bridge,
  the display connector bridge, in order to work, so this
  is required to have graphics working properly in kernel
  v5.9-rc1+

Link: https://lore.kernel.org/r/20200901082558.80388-1-linus.walleij@linaro.orgSigned-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Update the Integrator defconfig to the changes from the recent
kernel cycles and especially the v5.9-rc1 changes.

- Move options around as a result of Kconfig changes.
- Drop the ZBOOT_ROM* stuff that doesn't exist anymore.
- Select CONFIG_DRM_DISPLAY_CONNECTOR=y, the
  CONFIG_DRM_SIMPLE_BRIDGE was renamed when renaming the
  driver, but the simple bridge requires another bridge,
  the display connector bridge, in order to work, so this
  is required to have graphics working properly in kernel
  v5.9-rc1+

Link: https://lore.kernel.org/r/20200901073930.31548-1-linus.walleij@linaro.orgSigned-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

The IBM op-panel driver requires i2c slave mode.
Signed-off-by: Joel Stanley <joel@jms.id.au>

Used by rainier and q71l.
Signed-off-by: Joel Stanley <joel@jms.id.au>

In the 5.7 merge window the media kconfig was restructued. For most
platforms these changes set CONFIG_MEDIA_SUPPORT_FILTER=y which keeps
unwanted drivers disabled.

The exception is if a config sets EMBEDDED or EXPERT (see b0cd4fb2).
In that case the filter is set to =n, causing a bunch of DVB tuner drivers
(MEDIA_TUNER_*) to be accidentally enabled. This was noticed as it blew
out the build time for the Aspeed defconfigs.

Enabling the filter means the Aspeed config also needs to set
CONFIG_MEDIA_PLATFORM_SUPPORT=y in order to have the CONFIG_VIDEO_ASPEED
driver enabled.

Fixes: 06b93644 ("media: Kconfig: add an option to filter in/out platform drivers")
Fixes: b0cd4fb2 ("media: Kconfig: on !EMBEDDED && !EXPERT, enable driver filtering")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Cc: stable@vger.kernel.org
CC: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

Enable the Samsung S3FWRN5 NFC driver present in Exynos5433-based
TM2/TM2E boards.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200906153654.2925-10-krzk@kernel.org

Enable set of generic, widely used, networking  options:
- basic QoS, filter and actions
- VLAN support
- Bridge support
Use "M" build option where possible.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The ADC is used by twl4030_charger to read voltages. If a dtb contains
the ADC but the module is not build, probing twl4030_charger will be
endlessly deferred, so just enable CONFIG_TWL4030_MADC in the config.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The ROHM BD718x7 PMIC is present on many designs with i.MX 8M SoCs.
Enable the bd718x7 clock driver which provides PMICs 32 kHz clock.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

This commit builds ADMA and ACONNECT drivers which can be used on
Tegra210 and later platforms to transfer audio data to/from AHUB
(Audio Hub).
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

This patch helps to build AHUB and its client drivers (I2S, DMIC,
DSPK, ADMAIF and AHUB). These register components with ASoC core.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

config option PCIE_RCAR internally selects PCIE_RCAR_HOST which builds the
same driver. So this patch renames CONFIG_PCIE_RCAR to
CONFIG_PCIE_RCAR_HOST so that PCIE_RCAR can be safely dropped from Kconfig
file.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20200826093220.10266-3-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

config option PCIE_RCAR internally selects PCIE_RCAR_HOST which builds the
same driver. So this patch renames CONFIG_PCIE_RCAR to
CONFIG_PCIE_RCAR_HOST so that PCIE_RCAR can be safely dropped from Kconfig
file.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20200826093220.10266-2-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Pull crypto fixes from Herbert Xu:

 - fix regression in af_alg that affects iwd

 - restore polling delay in qat

 - fix double free in ingenic on error path

 - fix potential build failure in sa2ul due to missing Kconfig dependency

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: af_alg - Work around empty control messages without MSG_MORE
  crypto: sa2ul - add Kconfig selects to fix build error
  crypto: ingenic - Drop kfree for memory allocated with devm_kzalloc
  crypto: qat - add delay before polling mailbox

Pull x86 fixes from Thomas Gleixner:
 "Three interrupt related fixes for X86:

   - Move disabling of the local APIC after invoking fixup_irqs() to
     ensure that interrupts which are incoming are noted in the IRR and
     not ignored.

   - Unbreak affinity setting.

     The rework of the entry code reused the regular exception entry
     code for device interrupts. The vector number is pushed into the
     errorcode slot on the stack which is then lifted into an argument
     and set to -1 because that's regs->orig_ax which is used in quite
     some places to check whether the entry came from a syscall.

     But it was overlooked that orig_ax is used in the affinity cleanup
     code to validate whether the interrupt has arrived on the new
     target. It turned out that this vector check is pointless because
     interrupts are never moved from one vector to another on the same
     CPU. That check is a historical leftover from the time where x86
     supported multi-CPU affinities, but not longer needed with the now
     strict single CPU affinity. Famous last words ...

   - Add a missing check for an empty cpumask into the matrix allocator.

     The affinity change added a warning to catch the case where an
     interrupt is moved on the same CPU to a different vector. This
     triggers because a condition with an empty cpumask returns an
     assignment from the allocator as the allocator uses for_each_cpu()
     without checking the cpumask for being empty. The historical
     inconsistent for_each_cpu() behaviour of ignoring the cpumask and
     unconditionally claiming that CPU0 is in the mask struck again.
     Sigh.

  plus a new entry into the MAINTAINER file for the HPE/UV platform"

* tag 'x86-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/matrix: Deal with the sillyness of for_each_cpu() on UP
  x86/irq: Unbreak interrupt affinity setting
  x86/hotplug: Silence APIC only after all interrupts are migrated
  MAINTAINERS: Add entry for HPE Superdome Flex (UV) maintainers

Pull irq fixes from Thomas Gleixner:
 "A set of fixes for interrupt chip drivers:

   - Revert the platform driver conversion of interrupt chip drivers as
     it turned out to create more problems than it solves.

   - Fix a trivial typo in the new module helpers which made probing
     reliably fail.

   - Small fixes in the STM32 and MIPS Ingenic drivers

   - The TI firmware rework which had badly managed dependencies and had
     to wait post rc1"

* tag 'irq-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/ingenic: Leave parent IRQ unmasked on suspend
  irqchip/stm32-exti: Avoid losing interrupts due to clearing pending bits by mistake
  irqchip: Revert modular support for drivers using IRQCHIP_PLATFORM_DRIVER helperse
  irqchip: Fix probing deferal when using IRQCHIP_PLATFORM_DRIVER helpers
  arm64: dts: k3-am65: Update the RM resource types
  arm64: dts: k3-am65: ti-sci-inta/intr: Update to latest bindings
  arm64: dts: k3-j721e: ti-sci-inta/intr: Update to latest bindings
  irqchip/ti-sci-inta: Add support for INTA directly connecting to GIC
  irqchip/ti-sci-inta: Do not store TISCI device id in platform device id field
  dt-bindings: irqchip: Convert ti, sci-inta bindings to yaml
  dt-bindings: irqchip: ti, sci-inta: Update docs to support different parent.
  irqchip/ti-sci-intr: Add support for INTR being a parent to INTR
  dt-bindings: irqchip: Convert ti, sci-intr bindings to yaml
  dt-bindings: irqchip: ti, sci-intr: Update bindings to drop the usage of gic as parent
  firmware: ti_sci: Add support for getting resource with subtype
  firmware: ti_sci: Drop unused structure ti_sci_rm_type_map
  firmware: ti_sci: Drop the device id to resource type translation

Pull scheduler fix from Thomas Gleixner:
 "A single fix for the scheduler:

   - Make is_idle_task() __always_inline to prevent the compiler from
     putting it out of line into the wrong section because it's used
     inside noinstr sections"

* tag 'sched-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Use __always_inline on is_idle_task()

Pull locking fixes from Thomas Gleixner:
 "A set of fixes for lockdep, tracing and RCU:

   - Prevent recursion by using raw_cpu_* operations

   - Fixup the interrupt state in the cpu idle code to be consistent

   - Push rcu_idle_enter/exit() invocations deeper into the idle path so
     that the lock operations are inside the RCU watching sections

   - Move trace_cpu_idle() into generic code so it's called before RCU
     goes idle.

   - Handle raw_local_irq* vs. local_irq* operations correctly

   - Move the tracepoints out from under the lockdep recursion handling
     which turned out to be fragile and inconsistent"

* tag 'locking-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  lockdep,trace: Expose tracepoints
  lockdep: Only trace IRQ edges
  mips: Implement arch_irqs_disabled()
  arm64: Implement arch_irqs_disabled()
  nds32: Implement arch_irqs_disabled()
  locking/lockdep: Cleanup
  x86/entry: Remove unused THUNKs
  cpuidle: Move trace_cpu_idle() into generic code
  cpuidle: Make CPUIDLE_FLAG_TLB_FLUSHED generic
  sched,idle,rcu: Push rcu_idle deeper into the idle path
  cpuidle: Fixup IRQ state
  lockdep: Use raw_cpu_*() for per-cpu variables

Pull cfis fix from Steve French:
 "DFS fix for referral problem when using SMB1"

* tag '5.9-rc2-smb-fix' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: fix check of tcon dfs in smb1

Pull powerpc fixes from Michael Ellerman:

 - Revert our removal of PROT_SAO, at least one user expressed an
   interest in using it on Power9. Instead don't allow it to be used in
   guests unless enabled explicitly at compile time.

 - A fix for a crash introduced by a recent change to FP handling.

 - Revert a change to our idle code that left Power10 with no idle
   support.

 - One minor fix for the new scv system call path to set PPR.

 - Fix a crash in our "generic" PMU if branch stack events were enabled.

 - A fix for the IMC PMU, to correctly identify host kernel samples.

 - The ADB_PMU powermac code was found to be incompatible with
   VMAP_STACK, so make them incompatible in Kconfig until the code can
   be fixed.

 - A build fix in drivers/video/fbdev/controlfb.c, and a documentation
   fix.

Thanks to Alexey Kardashevskiy, Athira Rajeev, Christophe Leroy,
Giuseppe Sacco, Madhavan Srinivasan, Milton Miller, Nicholas Piggin,
Pratik Rajesh Sampat, Randy Dunlap, Shawn Anastasio, Vaidyanathan
Srinivasan.

* tag 'powerpc-5.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/32s: Disable VMAP stack which CONFIG_ADB_PMU
  Revert "powerpc/powernv/idle: Replace CPU feature check with PVR check"
  powerpc/perf: Fix reading of MSR[HV/PR] bits in trace-imc
  powerpc/perf: Fix crashes with generic_compat_pmu & BHRB
  powerpc/64s: Fix crash in load_fp_state() due to fpexc_mode
  powerpc/64s: scv entry should set PPR
  Documentation/powerpc: fix malformed table in syscall64-abi
  video: fbdev: controlfb: Fix build for COMPILE_TEST=y && PPC_PMAC=n
  selftests/powerpc: Update PROT_SAO test to skip ISA 3.1
  powerpc/64s: Disallow PROT_SAO in LPARs by default
  Revert "powerpc/64s: Remove PROT_SAO support"

Pull USB fixes from Greg KH:
 "Let's try this again...  Here are some USB fixes for 5.9-rc3.

  This differs from the previous pull request for this release in that
  the usb gadget patch now does not break some systems, and actually
  does what it was intended to do. Many thanks to Marek Szyprowski for
  quickly noticing and testing the patch from Andy Shevchenko to resolve
  this issue.

  Additionally, some more new USB quirks have been added to get some new
  devices to work properly based on user reports.

  Other than that, the patches are all here, and they contain:

   - usb gadget driver fixes

   - xhci driver fixes

   - typec fixes

   - new quirks and ids

   - fixes for USB patches that went into 5.9-rc1.

  All of these have been tested in linux-next with no reported issues"

* tag 'usb-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
  usb: storage: Add unusual_uas entry for Sony PSZ drives
  USB: Ignore UAS for JMicron JMS567 ATA/ATAPI Bridge
  usb: host: ohci-exynos: Fix error handling in exynos_ohci_probe()
  USB: gadget: u_f: Unbreak offset calculation in VLAs
  USB: quirks: Ignore duplicate endpoint on Sound Devices MixPre-D
  usb: typec: tcpm: Fix Fix source hard reset response for TDA 2.3.1.1 and TDA 2.3.1.2 failures
  USB: PHY: JZ4770: Fix static checker warning.
  USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()
  USB: gadget: u_f: add overflow checks to VLA macros
  xhci: Always restore EP_SOFT_CLEAR_TOGGLE even if ep reset failed
  xhci: Do warm-reset when both CAS and XDEV_RESUME are set
  usb: host: xhci: fix ep context print mismatch in debugfs
  usb: uas: Add quirk for PNY Pro Elite
  tools: usb: move to tools buildsystem
  USB: Fix device driver race
  USB: Also match device drivers using the ->match vfunc
  usb: host: xhci-tegra: fix tegra_xusb_get_phy()
  usb: host: xhci-tegra: otg usb2/usb3 port init
  usb: hcd: Fix use after free in usb_hcd_pci_remove()
  usb: typec: ucsi: Hold con->lock for the entire duration of ucsi_register_port()
  ...

Pull EDAC fix from Borislav Petkov:
 "A fix to properly clear ghes_edac driver state on driver remove so
  that a subsequent load can probe the system properly (Shiju Jose)"

* tag 'edac_urgent_for_v5.9_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
  EDAC/ghes: Fix NULL pointer dereference in ghes_edac_register()

Pull dma-mapping fix from Christoph Hellwig:
 "Fix a possibly uninitialized variable (Dan Carpenter)"

* tag 'dma-mapping-5.9-2' of git://git.infradead.org/users/hch/dma-mapping:
  dma-pool: Fix an uninitialized variable bug in atomic_pool_expand()

Most of the CPU mask operations behave the same way, but for_each_cpu() and
it's variants ignore the cpumask argument and claim that CPU0 is always in
the mask. This is historical, inconsistent and annoying behaviour.

The matrix allocator uses for_each_cpu() and can be called on UP with an
empty cpumask. The calling code does not expect that this succeeds but
until commit e027ffff ("x86/irq: Unbreak interrupt affinity setting")
this went unnoticed. That commit added a WARN_ON() to catch cases which
move an interrupt from one vector to another on the same CPU. The warning
triggers on UP.

Add a check for the cpumask being empty to prevent this.

Fixes: 2f75d9e1 ("genirq: Implement bitmap matrix allocator")
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org

Merge tag 'fallthrough-fixes-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux

Pull fallthrough fixes from Gustavo A. R. Silva:
 "Fix some minor issues introduced by the recent treewide fallthrough
  conversions:

   - Fix identation issue

   - Fix erroneous fallthrough annotation

   - Remove unnecessary fallthrough annotation

   - Fix code comment changed by fallthrough conversion"

* tag 'fallthrough-fixes-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
  arm64/cpuinfo: Remove unnecessary fallthrough annotation
  media: dib0700: Fix identation issue in dib8096_set_param_override()
  afs: Remove erroneous fallthough annotation
  iio: dpot-dac: fix code comment in dpot_dac_read_raw()

Commit ef91bb19 ("kernel.h: Silence sparse warning in
lower_32_bits") caused new warnings to show in the fsldma driver, but
that commit was not to blame: it only exposed some very incorrect code
that tried to take the low 32 bits of an address.

That made no sense for multiple reasons, the most notable one being that
that code was intentionally limited to only 32-bit ppc builds, so "only
low 32 bits of an address" was completely nonsensical.  There were no
high bits to mask off to begin with.

But even more importantly fropm a correctness standpoint, turning the
address into an integer then caused the subsequent address arithmetic to
be completely wrong too, and the "+1" actually incremented the address
by one, rather than by four.

Which again was incorrect, since the code was reading two 32-bit values
and trying to make a 64-bit end result of it all.  Surprisingly, the
iowrite64() did not suffer from the same odd and incorrect model.

This code has never worked, but it's questionable whether anybody cared:
of the two users that actually read the 64-bit value (by way of some C
preprocessor hackery and eventually the 'get_cdar()' inline function),
one of them explicitly ignored the value, and the other one might just
happen to work despite the incorrect value being read.

This patch at least makes it not fail the build any more, and makes the
logic superficially sane.  Whether it makes any difference to the code
_working_ or not shall remain a mystery.
Compile-tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull i2c fixes from Wolfram Sang:
 "A core fix for ACPI matching and two driver bugfixes"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: iproc: Fix shifting 31 bits
  i2c: rcar: in slave mode, clear NACK earlier
  i2c: acpi: Remove dead code, i.e. i2c_acpi_match_device()
  i2c: core: Don't fail PRP0001 enumeration when no ID table exist

Pull s390 fixes from Vasily Gorbik:

 - Disable preemption trace in percpu macros since the lockdep code
   itself uses percpu variables now and it causes recursions.

 - Fix kernel space 4-level paging broken by recent vmem rework.

* tag 's390-5.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/vmem: fix vmem_add_range for 4-level paging
  s390: don't trace preemption in percpu macros

Pull xen fixes from Juergen Gross:
 "Two fixes for Xen: one needed for ongoing work to support virtio with
  Xen, and one for a corner case in IRQ handling with Xen"

* tag 'for-linus-5.9-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  arm/xen: Add misuse warning to virt_to_gfn
  xen/xenbus: Fix granting of vmalloc'd memory
  XEN uses irqdesc::irq_data_common::handler_data to store a per interrupt XEN data pointer which contains XEN specific information.

Merge tag 'hwmon-for-v5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:

 - Fix tempeerature scale in gsc-hwmon driver

 - Fix divide by 0 error in nct7904 driver

 - Drop non-existing attribute from pmbus/isl68137 driver

 - Fix status check in applesmc driver

* tag 'hwmon-for-v5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (gsc-hwmon) Scale temperature to millidegrees
  hwmon: (applesmc) check status earlier.
  hwmon: (nct7904) Correct divide by 0
  hwmon: (pmbus/isl68137) remove READ_TEMPERATURE_1 telemetry for RAA228228