The current implementation of irq_set_affinity() refuses rightfully to
route an interrupt to an offline cpu.

But there is a special case, where this is actually desired. Some of
the ARM SoCs have per cpu timers which require setting the affinity
during cpu startup where the cpu is not yet in the online mask.

If we can't do that, then the local timer interrupt for the about to
become online cpu is routed to some random online cpu.

The developers of the affected machines tried to work around that
issue, but that results in a massive mess in that timer code.

We have a yet unused argument in the set_affinity callbacks of the irq
chips, which I added back then for a similar reason. It was never
required so it got not used. But I'm happy that I never removed it.

That allows us to implement a sane handling of the above scenario. So
the affected SoC drivers can add the required force handling to their
interrupt chip, switch the timer code to irq_force_affinity() and
things just work.

This does not affect any existing user of irq_set_affinity().

Tagged for stable to allow a simple fix of the affected SoC clock
event drivers.
Reported-and-tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>,
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>,
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20140416143315.717251504@linutronix.deSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Pull parisc updates from Helge Deller:
 "There are two major changes in this patchset:

  The major fix is that the epoll_pwait() syscall for 32bit userspace
  was not using the compat wrapper on a 64bit kernel.

  Secondly we changed the value of SHMLBA from 4MB to PAGE_SIZE to
  reflect that we can actually mmap to any multiple of PAGE_SIZE.  The
  only thing which needs care is that shared mmaps need to be mapped at
  the same offset inside the 4MB cache window"

* 'parisc-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: fix epoll_pwait syscall on compat kernel
  parisc: change value of SHMLBA from 0x00400000 to PAGE_SIZE
  parisc: Replace __get_cpu_var uses for address calculation

Merge ipmi fixes from Corey Minyard:
 "Things collected since last kernel release.

  Some of these are pretty important.  The first three are bug fixes.
  The next two are to hopefully make everyone happy about allowing
  ACPI to be on all the time and not have IPMI have an effect on the
  system when not in use.  The last is a little cleanup"

* emailed patches from Corey Minyard <cminyard@mvista.com>:
  ipmi: boolify some things
  ipmi: Turn off all activity on an idle ipmi interface
  ipmi: Turn off default probing of interfaces
  ipmi: Reset the KCS timeout when starting error recovery
  ipmi: Fix a race restarting the timer
  Char: ipmi_bt_sm, fix infinite loop

Convert some ints to bools.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The IPMI driver would wake up periodically looking for events and
watchdog pretimeouts.  If there is nothing waiting for these events,
it's really kind of pointless to be checking for them.  So modify the
driver so the message handler can pass down if it needs the lower layer
to be waiting for these.  Modify the system interface lower layer to
turn off all timer and thread activity if the upper layer doesn't need
anything and it is not currently handling messages.  And modify the
message handler to not restart the timer if its timer is not needed.

The timers and kthread will still be enabled if:
 - the SI interface is handling a message.
 - a user has enabled watching for events.
 - the IPMI watchdog timer is in use (since it uses pretimeouts).
 - the message handler is waiting on a remote response.
 - a user has registered to receive commands.

This mostly affects interfaces without interrupts.  Interfaces with
interrupts already don't use CPU in the system interface when the
interface is idle.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The default probing can cause problems with some system, slow booting,
extra CPU usages, etc.  Turn it off by default and give a config option
to enable it.

From: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The OBF timer in KCS was not reset in one situation when error recovery
was started, resulting in an immediate timeout.
Reported-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

With recent changes it is possible for the timer handler to detect an
idle interface and not start the timer, but the thread to start an
operation at the same time.  The thread will not start the timer in that
instance, resulting in the timer not running.

Instead, move all timer operations under the lock and start the timer in
the thread if it detect non-idle and the timer is not already running.
Moving under locks allows the last timeout to be set in both the thread
and the timer.  'Timer is not running' means that the timer is not
pending and smi_timeout() is not running.  So we need a flag to detect
this correctly.

Also fix a few other timeout bugs: setting the last timeout when the
interrupt has to be disabled and the timer started, and setting the last
timeout in check_start_timer_thread possibly racing with the timer
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In read_all_bytes, we do

  unsigned char i;
  ...
  bt->read_data[0] = BMC2HOST;
  bt->read_count = bt->read_data[0];
  ...
  for (i = 1; i <= bt->read_count; i++)
    bt->read_data[i] = BMC2HOST;

If bt->read_data[0] == bt->read_count == 255, we loop infinitely in the
'for' loop.  Make 'i' an 'int' instead of 'char' to get rid of the
overflow and finish the loop after 255 iterations every time.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-and-debugged-by: Rui Hui Dian <rhdian@novell.com>
Cc: Tomas Cech <tcech@suse.cz>
Cc: Corey Minyard <minyard@acm.org>
Cc: <openipmi-developer@lists.sourceforge.net>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull Xen fixes from David Vrabel:
 "Xen regression and bug fixes for 3.15-rc1:

   - fix completely broken 32-bit PV guests caused by x86 refactoring
     32-bit thread_info.
   - only enable ticketlock slow path on Xen (not bare metal)
   - fix two bugs with PV guests not shutting down when requested
   - fix a minor memory leak in xen-pciback error path"

* tag 'stable/for-linus-3.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/manage: Poweroff forcefully if user-space is not yet up.
  xen/xenbus: Avoid synchronous wait on XenBus stalling shutdown/restart.
  xen/spinlock: Don't enable them unconditionally.
  xen-pciback: silence an unwanted debug printk
  xen: fix memory leak in __xen_pcibk_add_pci_dev()
  x86/xen: Fix 32-bit PV guests's usage of kernel_stack

Pull md bugfix from Neil Brown:
 "One BUG fix for md for recent commit"

* tag '3.15-fixes' of git://neil.brown.name/md:
  raid5: fix a race of stripe count check

Pull fbdev renaming patches from Tomi Valkeinen:
 "Reorder drivers/video/ directory so that all fbdev drivers are now
  located in drivers/video/fbdev/ and the fbdev framework core files are
  located in drivers/video/fbdev/core/

  The drivers/video/Kconfig is modified so that the DRM and the fbdev
  menu options are in separate submenus, instead of both being mixed in
  the same 'Graphics support' menu level"

* tag 'fbdev-reorder-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
  video: Kconfig: move drm and fb into separate menus
  fbdev: move fbdev core files to separate directory
  video: move fbdev to drivers/video/fbdev

I hit another BUG_ON with e240c183. In __get_priority_stripe(),
stripe count equals to 0 initially. Between atomic_inc and BUG_ON,
get_active_stripe() finds the stripe. So the stripe count isn't 1 any more.

V2: keeps the BUG_ON suggested by Neil.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>

At the moment the "Device Drivers / Graphics support" kernel config page
looks rather messy, with DRM and fbdev driver selections on the same
page, some on the top level Graphics support page, some under their
respective subsystems.

If I'm not mistaken, this is caused by the drivers depending on other
things than DRM or FB, which causes Kconfig to arrange the options in
not-so-neat manner.

Both DRM and FB have a main menuconfig option for the whole DRM or FB
subsystem. Optimally, this would be enough to arrange all DRM and FB
options under the respective subsystem, but for whatever reason this
doesn't work reliably.

This patch adds an explicit submenu for DRM and FB, making it much
clearer which options are related to FB, and which to DRM.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Instead of having fbdev framework core files at the root fbdev
directory, mixed with random fbdev device drivers, move the fbdev core
files to a separate core directory. This makes it much clearer which of
the files are actually part of the fbdev framework, and which are part
of device drivers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

The drivers/video directory is a mess. It contains generic video related
files, directories for backlight, console, linux logo, lots of fbdev
device drivers, fbdev framework files.

Make some order into the chaos by creating drivers/video/fbdev
directory, and move all fbdev related files there.

No functionality is changed, although I guess it is possible that some
subtle Makefile build order related issue could be created by this
patch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Pull x86 fixes from Ingo Molnar:
 "Various fixes:

   - reboot regression fix
   - build message spam fix
   - GPU quirk fix
   - 'make kvmconfig' fix

  plus the wire-up of the renameat2() system call on i386"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86: Remove the PCI reboot method from the default chain
  x86/build: Supress "Nothing to be done for ..." messages
  x86/gpu: Fix sign extension issue in Intel graphics stolen memory quirks
  x86/platform: Fix "make O=dir kvmconfig"
  i386: Wire up the renameat2() syscall

Pull perf fixes from Ingo Molnar:
 "Tooling fixes, plus a simple hardware-enablement patch for the Intel
  RAPL PMU (energy use measurement) on Haswell CPUs, which I hope is
  still fine at this stage"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf tools: Instead of redirecting flex output, use -o
  perf tools: Fix double free in perf test 21 (code-reading.c)
  perf stat: Initialize statistics correctly
  perf bench: Set more defaults in the 'numa' suite
  perf bench: Fix segfault at the end of an 'all' execution
  perf bench: Update manpage to mention numa and futex
  perf probe: Use dwarf_getcfi_elf() instead of dwarf_getcfi()
  perf probe: Fix to handle errors in line_range searching
  perf probe: Fix --line option behavior
  perf tools: Pick up libdw without explicit LIBDW_DIR
  MAINTAINERS: Change e-mail to kernel.org one
  perf callchains: Disable unwind libraries when libelf isn't found
  tools lib traceevent: Do not call warning() directly
  tools lib traceevent: Print event name when show warning if possible
  perf top: Fix documentation of invalid -s option
  perf/x86: Enable DRAM RAPL support on Intel Haswell

Pull irq fix from Ingo Molnar:
 "ARM VIC (Vectored Irq Controller) irqchip driver fix"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip: vic: Properly chain the cascaded IRQs

Pull locking fixes from Ingo Molnar:
 "liblockdep fixes and mutex debugging fixes"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/mutex: Fix debug_mutexes
  tools/liblockdep: Add proper versioning to the shared obj
  tools/liblockdep: Ignore asmlinkage and visible

Pull fbdev fixes from Tomi Valkeinen:
 - fix build errors for bf54x-lq043fb and imxfb
 - fbcon fix for da8xx-fb
 - omapdss fixes for hdmi audio, irq handling and fclk calculation

* tag 'fbdev-fixes-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
  video: bf54x-lq043fb: fix build error
  OMAPDSS: Change struct reg_field to dispc_reg_field
  OMAPDSS: Take pixelclock unit change into account in hdmi_compute_acr()
  OMAPDSS: fix shared irq handlers
  video: imxfb: Select LCD_CLASS_DEVICE unconditionally
  OMAPDSS: fix rounding when calculating fclk rate
  video: da8xx-fb: Fix casting of info->pseudo_palette

Pull pincontrol fixes from Linus Walleij:
 "A first set of pin control fixes for the v3.15 series:

   - Fix a couple of barnsjukdomar on the Rockchip driver.

   - Remove an idiotic debug print I happened to leave behind in the
     Nomadik driver.

   - Fixup the Qualcomm MSM interrupt handling code for the TLMM v2.

   - Three patches renaming the Broadcom Capri driver to BCM28155.  This
     has been falling between the chairs for some time due to some
     cross-tree synchronization misunderstandings, now I'm fed up with
     this and just rename it in this -rc1 phase"

* tag 'pinctrl-v3.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: fix typo in bindings documentation
  Update bcm_defconfig with new pinctrl CONFIG
  pinctrl: Rename Broadcom Capri pinctrl driver
  pinctrl: msm: Correct interrupt code for TLMM v2
  pinctrl: nomadik: delete stray debug print
  pinctrl: rockchip: handle first half of rk3188-bank0 correctly
  pinctrl: rockchip: add return value to rockchip_set_mux
  pinctrl: rockchip: fix offset of mux registers for rk3188

Pull s390 patches from Martin Schwidefsky:
 "An update to the oops output with additional information about the
  crash.  The renameat2 system call is enabled.  Two patches in regard
  to the PTR_ERR_OR_ZERO cleanup.  And a bunch of bug fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/sclp_cmd: replace PTR_RET with PTR_ERR_OR_ZERO
  s390/sclp: replace PTR_RET with PTR_ERR_OR_ZERO
  s390/sclp_vt220: Fix kernel panic due to early terminal input
  s390/compat: fix typo
  s390/uaccess: fix possible register corruption in strnlen_user_srst()
  s390: add 31 bit warning message
  s390: wire up sys_renameat2
  s390: show_registers() should not map user space addresses to kernel symbols
  s390/mm: print control registers and page table walk on crash
  s390/smp: fix smp_stop_cpu() for !CONFIG_SMP
  s390: fix control register update

Pull itanium erratum fix from Tony Luck:
 "Small workaround for a rare, but annoying, erratum #237"

* tag 'please-pull-ia64-erratum' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
  [IA64] Change default PSR.ac from '1' to '0' (Fix erratum #237)

April 2014 Itanium processor specification update:

http://www.intel.com/content/www/us/en/processors/itanium/itanium-specification-update.html

describes this erratum:

=========================================================================
237. Under a complex set of conditions, store to load forwarding for a
sub 8-byte load may complete incorrectly

Problem: A load instruction may complete incorrectly when a code sequence
using 4-byte or smaller load and store operations to the same address
is executed in combination with specific timing of all the following
concurrent conditions: store to load forwarding, alignment checking
enabled, a mis-predicted branch, and complex cache utilization activity.

Implication: The affected sub 8-byte instruction may complete
incorrectly resulting in unpredictable system behavior. There is an
extremely low probability of exposure due to the significant number of
complex microarchitectural concurrent conditions required to encounter
the erratum.

Workaround: Set PSR.ac = 0 to completely avoid the erratum. Disabling
Hyper-Threading will significantly reduce exposure to the conditions
that contribute to encountering the erratum.

Status: See the Summary Table of Changes for the affected steppings.
=========================================================================

[Table of changes essentially lists all models from McKinley to Tukwila]

The PSR.ac bit controls whether the processor will always generate
an unaligned reference trap (0x5a00) for a misaligned data access
(when PSR.ac=1) or if it will let the access succeed when running
on a cpu that implements logic to handle some unaligned accesses.

Way back in 2008 in commit b704882e
  [IA64] Rationalize kernel mode alignment checking
we made the decision to always enable strict checking. We were
already doing so in trap/interrupt context because the common
preamble code set this bit - but the rest of supervisor code
(and by inheritance user code) ran with PSR.ac=0.

We now reverse that decision and set PSR.ac=0 everywhere in the
kernel (also inherited by user processes). This will avoid the
erratum using the method described in the Itanium specification
update.  Net effect for users is that the processor will handle
unaligned access when it can (typically with a tiny performance
bubble in the pipeline ... but much less invasive than taking a
trap and having the OS perform the access).
Signed-off-by: Tony Luck <tony.luck@intel.com>

Steve reported a reboot hang and bisected it back to this commit:

  a4f1987e x86, reboot: Add EFI and CF9 reboot methods into the default list

He heroically tested all reboot methods and found the following:

  reboot=t       # triple fault                  ok
  reboot=k       # keyboard ctrl                 FAIL
  reboot=b       # BIOS                          ok
  reboot=a       # ACPI                          FAIL
  reboot=e       # EFI                           FAIL   [system has no EFI]
  reboot=p       # PCI 0xcf9                     FAIL

And I think it's pretty obvious that we should only try PCI 0xcf9 as a
last resort - if at all.

The other observation is that (on this box) we should never try
the PCI reboot method, but close with either the 'triple fault'
or the 'BIOS' (terminal!) reboot methods.

Thirdly, CF9_COND is a total misnomer - it should be something like
CF9_SAFE or CF9_CAREFUL, and 'CF9' should be 'CF9_FORCE' ...

So this patch fixes the worst problems:

 - it orders the actual reboot logic to follow the reboot ordering
   pattern - it was in a pretty random order before for no good
   reason.

 - it fixes the CF9 misnomers and uses BOOT_CF9_FORCE and
   BOOT_CF9_SAFE flags to make the code more obvious.

 - it tries the BIOS reboot method before the PCI reboot method.
   (Since 'BIOS' is a terminal reboot method resulting in a hang
    if it does not work, this is essentially equivalent to removing
    the PCI reboot method from the default reboot chain.)

 - just for the miraculous possibility of terminal (resulting
   in hang) reboot methods of triple fault or BIOS returning
   without having done their job, there's an ordering between
   them as well.
Reported-and-bisected-and-tested-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Li Aubrey <aubrey.li@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Link: http://lkml.kernel.org/r/20140404064120.GB11877@gmail.comSigned-off-by: Ingo Molnar <mingo@kernel.org>

Pull networking fixes from David Miller:

 1) Fix BPF filter validation of netlink attribute accesses, from
    Mathias Kruase.

 2) Netfilter conntrack generation seqcount not initialized properly,
    from Andrey Vagin.

 3) Fix comparison mask computation on big-endian in nft_cmp_fast(),
    from Patrick McHardy.

 4) Properly limit MTU over ipv6, from Eric Dumazet.

 5) Fix seccomp system call argument population on 32-bit, from Daniel
    Borkmann.

 6) skb_network_protocol() should not use hard-coded ETH_HLEN, instead
    skb->mac_len needs to be used.  From Vlad Yasevich.

 7) We have several cases of using socket based communications to
    implement a tunnel.  For example, some tunnels are encapsulations
    over UDP so we use an internal kernel UDP socket to do the
    transmits.

    These tunnels should behave just like other software devices and
    pass the packets on down to the next layer.

    Most importantly we want the top-level socket (eg TCP) that created
    the traffic to be charged for the SKB memory.

    However, once you get into the IP output path, we have code that
    assumed that whatever was attached to skb->sk is an IP socket.

    To keep the top-level socket being charged for the SKB memory,
    whilst satisfying the needs of the IP output path, we now pass in an
    explicit 'sk' argument.

    From Eric Dumazet.

 8) ping_init_sock() leaks group info, from Xiaoming Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
  cxgb4: use the correct max size for firmware flash
  qlcnic: Fix MSI-X initialization code
  ip6_gre: don't allow to remove the fb_tunnel_dev
  ipv4: add a sock pointer to dst->output() path.
  ipv4: add a sock pointer to ip_queue_xmit()
  driver/net: cosa driver uses udelay incorrectly
  at86rf230: fix __at86rf230_read_subreg function
  at86rf230: remove check if AVDD settled
  net: cadence: Add architecture dependencies
  net: Start with correct mac_len in skb_network_protocol
  Revert "net: sctp: Fix a_rwnd/rwnd management to reflect real state of the receiver's buffer"
  cxgb4: Save the correct mac addr for hw-loopback connections in the L2T
  net: filter: seccomp: fix wrong decoding of BPF_S_ANC_SECCOMP_LD_W
  seccomp: fix populating a0-a5 syscall args in 32-bit x86 BPF
  qlcnic: Do not disable SR-IOV when VFs are assigned to VMs
  qlcnic: Fix QLogic application/driver interface for virtual NIC configuration
  qlcnic: Fix PVID configuration on eSwitch port.
  qlcnic: Fix max ring count calculation
  qlcnic: Fix to send INIT_NIC_FUNC as first mailbox.
  qlcnic: Fix panic due to uninitialzed delayed_work struct in use.
  ...

The wrong max fw size was being used and causing false
"too big" errors running ethtool -f.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Function qlcnic_setup_tss_rss_intr() might enter endless
loop in case pci_enable_msix() contiguously returns a
positive number of MSI-Xs that could have been allocated.
Besides, the function contains 'err = -EIO;' assignment
that never could be reached. This update fixes the
aforementioned issues.

Cc: Shahed Shaikh <shahed.shaikh@qlogic.com>
Cc: Dept-HSGLinuxNICDev@qlogic.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's possible to remove the FB tunnel with the command 'ip link del ip6gre0' but
this is unsafe, the module always supposes that this device exists. For example,
ip6gre_tunnel_lookup() may use it unconditionally.

Let's add a rtnl handler for dellink, which will never remove the FB tunnel (we
let ip6gre_destroy_tunnels() do the job).

Introduced by commit c12b395a ("gre: Support GRE over IPv6").

CC: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the dst->output() path for ipv4, the code assumes the skb it has to
transmit is attached to an inet socket, specifically via
ip_mc_output() : The sk_mc_loop() test triggers a WARN_ON() when the
provider of the packet is an AF_PACKET socket.

The dst->output() method gets an additional 'struct sock *sk'
parameter. This needs a cascade of changes so that this parameter can
be propagated from vxlan to final consumer.

Fixes: 8f646c92 ("vxlan: keep original skb ownership")
Reported-by: lucien xin <lucien.xin@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/jolsa/perf into perf/urgent

Pull perf/urgent fixes from Jiri Olsa:

  * Instead of redirecting flex output, use -o (Cody P Schafer)

  * Fix double free in perf test 21 (Adrian Hunter)
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>

ip_queue_xmit() assumes the skb it has to transmit is attached to an
inet socket. Commit 31c70d59 ("l2tp: keep original skb ownership")
changed l2tp to not change skb ownership and thus broke this assumption.

One fix is to add a new 'struct sock *sk' parameter to ip_queue_xmit(),
so that we do not assume skb->sk points to the socket used by l2tp
tunnel.

Fixes: 31c70d59 ("l2tp: keep original skb ownership")
Reported-by: Zhan Jianyu <nasa4836@gmail.com>
Tested-by: Zhan Jianyu <nasa4836@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The user can launch the guest in this sequence:

xl create -p /vm.cfg	[launch, but pause it]
xl shutdown latest	[sets control/shutdown=poweroff]
xl unpause latest
xl console latest	[and see that the guest has completely
ignored the shutdown request]

In reality the guest hasn't ignored it. It registers a watch
and gets a notification that there is value. It then calls
the shutdown_handler which ends up calling orderly_shutdown.

Unfortunately that is so early in the bootup that there
are no user-space. Which means that the orderly_shutdown fails.
But since the force flag was set to false it continues on without
reporting.

What we really want to is to use the force when we are in the
SYSTEM_BOOTING state and not use the 'force' when SYSTEM_RUNNING.

However, if we are in the running state - and the shutdown command
has been given before the user-space has been setup, there is nothing
we can do. Worst yet, we stop ignoring the 'xl shutdown' requests!

As such, the other part of this patch is to only stop ignoring
the 'xl shutdown' when we are truly in the power off sequence.

That means the user can do multiple 'xl shutdown' and we will try
to act on them instead of ignoring them.

Fixes-Bug: http://bugs.xenproject.org/xen/bug/6Reported-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

The 'read_reply' works with 'process_msg' to read of a reply in XenBus.
'process_msg' is running from within the 'xenbus' thread. Whenever
a message shows up in XenBus it is put on a xs_state.reply_list list
and 'read_reply' picks it up.

The problem is if the backend domain or the xenstored process is killed.
In which case 'xenbus' is still awaiting - and 'read_reply' if called -
stuck forever waiting for the reply_list to have some contents.

This is normally not a problem - as the backend domain can come back
or the xenstored process can be restarted. However if the domain
is in process of being powered off/restarted/halted - there is no
point of waiting on it coming back - as we are effectively being
terminated and should not impede the progress.

This patch solves this problem by checking whether the guest is the
right domain. If it is an initial domain and hurtling towards death -
there is no point of continuing the wait. All other type of guests
continue with their behavior (as Xenstore is expected to still be
running in another domain).

Fixes-Bug: http://bugs.xenproject.org/xen/bug/8Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

The git commit a945928e
('xen: Do not enable spinlocks before jump_label_init() has executed')
was added to deal with the jump machinery. Earlier the code
that turned on the jump label was only called by Xen specific
functions. But now that it had been moved to the initcall machinery
it gets called on Xen, KVM, and baremetal - ouch!. And the detection
machinery to only call it on Xen wasn't remembered in the heat
of merge window excitement.

This means that the slowpath is enabled on baremetal while it should
not be.
Reported-by: Waiman Long <waiman.long@hp.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
CC: stable@vger.kernel.org
CC: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

There is a missing curly brace here so we might print some extra debug
information.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

It need to free dev_entry when it failed to assign to a new
slot on the virtual PCI bus.

smatch says:
 drivers/xen/xen-pciback/vpci.c:142 __xen_pcibk_add_pci_dev() warn:
possible memory leak of 'dev_entry'
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

We are flagging the parent IRQ as chained, then we must also
make sure to call the chained_irq_[enter|exit] functions for
things to work smoothly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: http://lkml.kernel.org/r/1397550484-7119-1-git-send-email-linus.walleij@linaro.orgSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Commit 198d208d ("x86: Keep
thread_info on thread stack in x86_32") made 32-bit kernels use
kernel_stack to point to thread_info. That change missed a couple of
updates needed by Xen's 32-bit PV guests:

1. kernel_stack needs to be initialized for secondary CPUs

2. GET_THREAD_INFO() now uses %fs register which may not be the
   kernel's version when executing xen_iret().

With respect to the second issue, we don't need GET_THREAD_INFO()
anymore: we used it as an intermediate step to get to per_cpu xen_vcpu
and avoid referencing %fs. Now that we are going to use %fs anyway we
may as well go directly to xen_vcpu.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>