Pull x86 fixes from Ingo Molnar:
 "Misc fixes: two KASAN fixes, two EFI boot fixes, two boot-delay
  optimization fixes, and a fix for a IRQ handling hang observed on
  virtual platforms"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm, kasan: Silence KASAN warnings in get_wchan()
  compiler, atomics, kasan: Provide READ_ONCE_NOCHECK()
  x86, kasan: Fix build failure on KASAN=y && KMEMCHECK=y kernels
  x86/smpboot: Fix CPU #1 boot timeout
  x86/smpboot: Fix cpu_init_udelay=10000 corner case boot parameter misbehavior
  x86/ioapic: Disable interrupts when re-routing legacy IRQs
  x86/setup: Extend low identity map to cover whole kernel range
  x86/efi: Fix multiple GOP device support

Pull scheduler fixes from Ingo Molnar:
 "Misc fixes all around the map: an instrumentation fix, a nohz
  usability fix, a lockdep annotation fix and two task group scheduling
  fixes"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/core: Add missing lockdep_unpin() annotations
  sched/deadline: Fix migration of SCHED_DEADLINE tasks
  nohz: Revert "nohz: Set isolcpus when nohz_full is set"
  sched/fair: Update task group's load_avg after task migration
  sched/fair: Fix overly small weight for interactive group entities
  sched, tracing: Stop/start critical timings around the idle=poll idle loop

Merge fixes from Andrew Morton:
 "9 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  ocfs2/dlm: unlock lockres spinlock before dlm_lockres_put
  fault-inject: fix inverted interval/probability values in printk
  lib/Kconfig.debug: disable -Wframe-larger-than warnings with KASAN=y
  mm: make sendfile(2) killable
  thp: use is_zero_pfn() only after pte_present() check
  mailmap: update Javier Martinez Canillas' email
  MAINTAINERS: add Sergey as zsmalloc reviewer
  mm: cma: fix incorrect type conversion for size during dma allocation
  kmod: don't run async usermode helper as a child of kworker thread

Luca and Wanpeng reported two missing annotations that led to
false lockdep complaints. Add the missing annotations.
Reported-by: Luca Abeni <luca.abeni@unitn.it>
Reported-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Juri Lelli <juri.lelli@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: cbce1a68 ("sched,lockdep: Employ lock pinning")
Link: http://lkml.kernel.org/r/20151023095008.GY17308@twins.programming.kicks-ass.netSigned-off-by: Ingo Molnar <mingo@kernel.org>

Pull powerpc fixes from Michael Ellerman:

 - Revert "Use the POWER8 Micro Partition Prefetch Engine in KVM HV on
   POWER8" from Paul
 - Handle irq_happened flag correctly in off-line loop from Paul
 - Validate rtas.entry before calling enter_rtas() from Vasant

* tag 'powerpc-4.3-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/rtas: Validate rtas.entry before calling enter_rtas()
  powerpc/powernv: Handle irq_happened flag correctly in off-line loop
  powerpc: Revert "Use the POWER8 Micro Partition Prefetch Engine in KVM HV on POWER8"

Pull ARM SoC fixes from Arnd Bergmann:
 "Most of the changes this time are for incorrect device nodes in
  various ways, on on imx, berlin, exynos, ux500, uniphier, omap and
  meson.

  Chen-Yu Tsai now co-maintains mach-sunxi (Allwinner).

  Other bug fixes include
   - a partial revert of a broken tegra gpio patch
   - irq affinity for arm ccn
   - suspend on one Armada 385 machine
   - enable ZONE_DMA to avoid an OMAP crash for over 2GB RAM
   - turning on a regulator on beagleboard-x15 for HDMI
   - making the omap gpmc debug code visible
   - setup of orion network switch
   - a rare build regression for pxa"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
  ARM: OMAP2+: Fix imprecise external abort caused by bogus SRAM init
  thermal: exynos: Fix register read in TMU
  ARM: OMAP2+: Fix oops with LPAE and more than 2GB of memory
  ARM: tegra: Comment out gpio-ranges properties
  ARM: dts: uniphier: fix IRQ number for devices on PH1-LD6b ref board
  drivers/perf: arm_pmu: avoid CPU device_node reference leak
  bus: arm-ccn: Fix irq affinity setting on CPU migration
  bus: arm-ccn: Handle correctly no-more-cpus case
  ARM: mvebu: correct a385-db-ap compatible string
  ARM: meson6: DTS: Fix wrong reg mapping and IRQ numbers
  MAINTAINERS: Update Allwinner entry and add new maintainer
  ARM: ux500: modify initial levelshifter status
  ARM: pxa: fix pxa3xx DFI lockup hack
  Documentation: ARM: List new omap MMC requirements
  memory: omap-gpmc: dump "before" state before first modification
  memory: omap-gpmc: Fix unselectable debug option for GPMC
  ARM: dts: am57xx-beagle-x15: set VDD_SD to always-on
  ARM: dts: Fix audio card detection on Peach boards
  ARM: EXYNOS: Fix double of_node_put() when parsing child power domains
  ARM: orion: Fix DSA platform device after mvmdio conversion
  ...

Pull KVM bugfixes from Paolo Bonzini:
 "Bug fixes for ARM, mostly 4.3 regressions related to virtual interrupt
  controller changes"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  arm/arm64: KVM: Fix disabled distributor operation
  arm/arm64: KVM: Clear map->active on pend/active clear
  arm/arm64: KVM: Fix arch timer behavior for disabled interrupts
  KVM: arm: use GIC support unconditionally
  KVM: arm/arm64: Fix memory leak if timer initialization fails
  KVM: arm/arm64: Do not inject spurious interrupts

Merge tag 'trace-fixes-v4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull tracing fixes from Steven Rostedt:
 "Running tests on other changes, the system locked up due to lots of
  warnings.  It was caused by the stack tracer triggering a warning
  about using rcu_dereference() when RCU was not watching.  This can
  happen due to the fact that the stack tracer uses the function tracer
  to check each function, and there are functions that may be called and
  traced when RCU stopped watching.  Namely when a function is called
  just before going idle or to userspace and after RCU stopped watching
  that current CPU.

  The first patch makes sure that RCU is watching when the stack tracer
  uses RCU.  The second patch is to make sure that the stack tracer does
  not get called by functions in NMI, as it's not NMI safe"

* tag 'trace-fixes-v4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Do not allow stack_tracer to record stack in NMI
  tracing: Have stack tracer force RCU to be watching

Pull sound fixes from Takashi Iwai:
 "There is nothing to worry you much, only a few small & stable patches
  are found for usual stuff, HD-audio (a Lenovo laptop quirk, a fix for
  minor error handling) and ASoC (trivial fixes for RT298 and WM
  codecs).

  The only remaining major change is the fix for ASoC SX_TLV control
  that was overseen during refactoring, but the fix itself is trivial
  and safe"

* tag 'sound-4.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ASoC: wm8962: mark cache_dirty flag after software reset in pm_resume
  ASoC: rt298: fix wrong setting of gpio2_en
  ASoC: wm8904: Correct number of EQ registers
  ALSA: hda - Fix deadlock at error in building PCM
  ASoC: Add info callback for SX_TLV controls
  ASoC: rt298: correct index default value
  ALSA: hda - Fix inverted internal mic on Lenovo G50-80
  ALSA: hdac: Explicitly add io.h

Pull media fixes from Mauro Carvalho Chehab:
 "Some regression fixes and potential security issues:

   - netup_unidvb: fix potential crash when spi is NULL
   - rtl28xxu: fix control message flaws
   - m88ds3103: fix a regression on Kernel 4.2
   - c8sectpfe: fix some issues on this new driver
   - v4l2-flash-led-class: fix a Kbuild dependency
   - si2157 and si2158: check for array boundary when uploading firmware
     files
   - horus3a and lnbh25: fix some building troubles when some options
     aren't selected
   - ir-hix5hd2: drop the use of IRQF_NO_SUSPEND"

* tag 'media/v4.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] m88ds3103: use own reg update_bits() implementation
  [media] rtl28xxu: fix control message flaws
  [media] v4l2-flash-led-class: Add missing VIDEO_V4L2 Kconfig dependency
  [media] netup_unidvb: fix potential crash when spi is NULL
  [media] si2168: Bounds check firmware
  [media] si2157: Bounds check firmware
  [media] ir-hix5hd2: drop the use of IRQF_NO_SUSPEND
  [media] c8sectpfe: fix return of garbage
  [media] c8sectpfe: fix ininitialized error return on firmware load failure
  [media] lnbh25: Fix lnbh25_attach() function return type
  [media] horus3a: Fix horus3a_attach() function parameters

Pull drm fixes from Dave Airlie:
 "I've been a bit slow gathering these:

   - drm/mst: one mutex leak in a fail path

   - radeon: two oops fixes, one dpm fix

   - i915: one messy set of fixes, where we revert the original fix, and
           pull back the proper set of fixes from -next on top.

   - nouveau: one fix for an illegal buffer placement.

  Doesn't look too bad, hopefully shouldn't be too much more"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/nouveau/gem: return only valid domain when there's only one
  drm: fix mutex leak in drm_dp_get_mst_branch_device
  drm/amdgpu: add missing dpm check for KV dpm late init
  drm/amdgpu/dpm: don't add pwm attributes if DPM is disabled
  drm/radeon/dpm: don't add pwm attributes if DPM is disabled
  drm/i915: Add primary plane to mask if it's visible
  drm/i915: Move sprite/cursor plane disable to intel_sanitize_crtc()
  drm/i915: Assign hwmode after encoder state readout
  Revert "drm/i915: Add primary plane to mask if it's visible"
  drm/i915: Deny wrapping an userptr into a framebuffer
  drm/i915: Enable DPLL VGA mode before P1/P2 divider write
  drm/i915: Restore lost DPLL register write on gen2-4
  drm/i915: Flush pipecontrol post-sync writes
  drm/i915: Fix kerneldoc for i915_gem_shrink_all

dlm_lockres_put will call dlm_lockres_release if it is the last
reference, and then it may call dlm_print_one_lock_resource and
take lockres spinlock.

So unlock lockres spinlock before dlm_lockres_put to avoid deadlock.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

interval displays the probability and vice versa.

Fixes: 6adc4a22 ("fault-inject: add ratelimit option")
Acked-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When the kernel compiled with KASAN=y, GCC adds redzones for each
variable on stack.  This enlarges function's stack frame and causes:

	'warning: the frame size of X bytes is larger than Y bytes'

The worst case I've seen for now is following:

   ../net/wireless/nl80211.c: In function `nl80211_send_wiphy':
   ../net/wireless/nl80211.c:1731:1: warning: the frame size of 5448 bytes is larger than 2048 bytes [-Wframe-larger-than=]

That kind of warning becomes useless with KASAN=y.  It doesn't
necessarily indicate that there is some problem in the code, thus we
should turn it off.

(The KASAN=y stack size in increased from 16k to 32k for this reason)
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Abylay Ospan <aospan@netup.ru>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Kozlov Sergey <serjk@netup.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently a simple program below issues a sendfile(2) system call which
takes about 62 days to complete in my test KVM instance.

        int fd;
        off_t off = 0;

        fd = open("file", O_RDWR | O_TRUNC | O_SYNC | O_CREAT, 0644);
        ftruncate(fd, 2);
        lseek(fd, 0, SEEK_END);
        sendfile(fd, fd, &off, 0xfffffff);

Now you should not ask kernel to do a stupid stuff like copying 256MB in
2-byte chunks and call fsync(2) after each chunk but if you do, sysadmin
should have a way to stop you.

We actually do have a check for fatal_signal_pending() in
generic_perform_write() which triggers in this path however because we
always succeed in writing something before the check is done, we return
value > 0 from generic_perform_write() and thus the information about
signal gets lost.

Fix the problem by doing the signal check before writing anything.  That
way generic_perform_write() returns -EINTR, the error gets propagated up
and the sendfile loop terminates early.
Signed-off-by: Jan Kara <jack@suse.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Use is_zero_pfn() on pteval only after pte_present() check on pteval
(It might be better idea to introduce is_zero_pte() which checks
pte_present() first).

Otherwise when working on a swap or migration entry and if pte_pfn's
result is equal to zero_pfn by chance, we lose user's data in
__collapse_huge_page_copy().  So if you're unlucky, the application
segfaults and finally you could see below message on exit:

BUG: Bad rss-counter state mm:ffff88007f099300 idx:2 val:3

Fixes: ca0984ca ("mm: incorporate zero pages into transparent huge pages")
Signed-off-by: Minchan Kim <minchan@kernel.org>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: <stable@vger.kernel.org>	[4.1+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The get_maintainer script still reports my old Collabora email based on
old commits but that address no longer exist so update mailmap to report
my current email and avoid people sending to the old address.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Nominate myself as a zsmalloc reviewer.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This was found during userspace fuzzing test when a large size dma cma
allocation is made by driver(like ion) through userspace.

  show_stack+0x10/0x1c
  dump_stack+0x74/0xc8
  kasan_report_error+0x2b0/0x408
  kasan_report+0x34/0x40
  __asan_storeN+0x15c/0x168
  memset+0x20/0x44
  __dma_alloc_coherent+0x114/0x18c
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

call_usermodehelper_exec_sync() does fork() + wait() with "unignored"
SIGCHLD.  What we have missed is that this worker thread can have other
children previously forked by call_usermodehelper_exec_work() without
UMH_WAIT_PROC.  If such a child exits in between it becomes a zombie
because auto-reaping only works if SIGCHLD is ignored, and nobody can
reap it (unless/until this worker thread exits too).

Change the !UMH_WAIT_PROC case to use CLONE_PARENT.

Note: this is only first step.  All PF_KTHREAD tasks, even created by
kernel_thread() should have ->parent == kthreadd by default.

Fixes: bb304a5c ("kmod: handle UMH_WAIT_PROC from system unbound workqueue")
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'asoc-fix-v4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v4.3

A bunch of driver fixes plus one core fix which fixes problems with
misreporting values from _SX controls following a recent refactoring.
This had gone unnoticed as such controls are quite rare.

Merge remote-tracking branches 'asoc/fix/rt298', 'asoc/fix/sx', 'asoc/fix/wm8904' and 'asoc/fix/wm8962' into asoc-linus

Device stopped to tuning some channels after regmap conversion.
Reason is that regmap_update_bits() works a bit differently for
partially volatile registers than old homemade routine. Return
back to old routine in order to fix issue.

Fixes: 478932b1

Cc: <stable@kernel.org> # 4.2+
Reported-by: Mark Clarkstone <hello@markclarkstone.co.uk>
Tested-by: Mark Clarkstone <hello@markclarkstone.co.uk>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Add lock to prevent concurrent access for control message as control
message function uses shared buffer. Without the lock there may be
remote control polling which messes the buffer causing IO errors.
Increase buffer size and add check for maximum supported message
length.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=103391
Fixes: c56222a6 ("[media] rtl28xxu: move usb buffers to state")

Cc: <stable@vger.kernel.org> # 4.0+
Signed-off-by: Antti Palosaari <crope@iki.fi>

Fixes the following randconfig problem:

drivers/built-in.o: In function `v4l2_flash_release':
(.text+0x12204f): undefined reference to `v4l2_async_unregister_subdev'
drivers/built-in.o: In function `v4l2_flash_release':
(.text+0x122057): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o: In function `v4l2_flash_close':
v4l2-flash-led-class.c:(.text+0x12208f): undefined reference to `v4l2_fh_is_singular'
v4l2-flash-led-class.c:(.text+0x1220c8): undefined reference to `__v4l2_ctrl_s_ctrl'
drivers/built-in.o: In function `v4l2_flash_open':
v4l2-flash-led-class.c:(.text+0x12227f): undefined reference to `v4l2_fh_is_singular'
drivers/built-in.o: In function `v4l2_flash_init_controls':
v4l2-flash-led-class.c:(.text+0x12274e): undefined reference to `v4l2_ctrl_handler_init_class'
v4l2-flash-led-class.c:(.text+0x122797): undefined reference to `v4l2_ctrl_new_std_menu'
v4l2-flash-led-class.c:(.text+0x1227e0): undefined reference to `v4l2_ctrl_new_std'
v4l2-flash-led-class.c:(.text+0x122826): undefined reference to `v4l2_ctrl_handler_setup'
v4l2-flash-led-class.c:(.text+0x122839): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o: In function `v4l2_flash_init':
(.text+0x1228e2): undefined reference to `v4l2_subdev_init'
drivers/built-in.o: In function `v4l2_flash_init':
(.text+0x12293b): undefined reference to `v4l2_async_register_subdev'
drivers/built-in.o: In function `v4l2_flash_init':
(.text+0x122949): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o:(.rodata+0x20ef8): undefined reference to `v4l2_subdev_queryctrl'
drivers/built-in.o:(.rodata+0x20f10): undefined reference to `v4l2_subdev_querymenu'
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Hans Verkuil <hans.verkuil@cisco.com>

Signed-off-by: Abylay Ospan <aospan@netup.ru>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

When reading the firmware and sending commands, the length must
be bounds checked to avoid overrunning the size of the command
buffer and smashing the stack if the firmware is not in the expected
format:

si2168 11-0064: found a 'Silicon Labs Si2168-B40'
si2168 11-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
si2168 11-0064: firmware download failed -95
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: ffffffffa085708f

Add the proper check.

Cc: stable@kernel.org
Reported-by: Stuart Auchterlonie <sauchter@redhat.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

When reading the firmware and sending commands, the length
must be bounds checked to avoid overrunning the size of the command
buffer and smashing the stack if the firmware is not in the
expected format. Add the proper check.

Cc: stable@kernel.org
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This driver doesn't claim the IR transmitter to be wakeup source. It
even disables the clock and the IR during suspend-resume cycle.

This patch removes yet another misuse of IRQF_NO_SUSPEND.

Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Guoxiong Yan <yanguoxiong@huawei.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The variable err was never initialized, that means we had been checking
a garbage value in the for loop. Moreover if the segment is not outside
the firmware file then also we have been returning the garbage.
Initialize it to 0 so that on success we return the value and no need to
check in the for loop also as it is initially 0 and whenever that value
changes we have done a break from the loop.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

static analysis with cppcheck detected the following error:

[drivers/media/platform/sti/c8sectpfe/c8sectpfe-core.c:1210]:
  (error) Uninitialized variable: ret

ret is never initialised, so garbage is being returned. Instead
return the error return from the call of request_firmware_nowait
Signed-off-by: Colin Ian King <colin.king@canonical.com>

If CONFIG_DVB_LNBH25 is disabled, a stub static inline function is
defined that just prints a warning about the driver being disabled
but the function return type was wrong which caused a build error.

Fixes: e025273b ("[media] lnbh25: LNBH25 SEC controller driver")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>

If CONFIG_DVB_HORUS3A is disabled a stub static inline function is
defined that just prints a warning about the driver being disabled
but the function parameters were wrong which caused a build error.

Fixes: a5d32b35 ("[media] horus3a: Sony Horus3A DVB-S/S2 tuner driver")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>

By doing software reset of wm8962 in pm_resume, all registers which
have already been set will be reset to default value without regmap
interface be involved, thus driver need to mark cache_dirty flag,
to let regcache can be updated by regcache_sync().
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Just a crash fix for radeon and amdgpu if the user has forcibly disabled
dpm and tries to access the pwm sysfs controls.

* 'drm-fixes-4.3' of git://people.freedesktop.org/~agd5f/linux:
  drm/amdgpu: add missing dpm check for KV dpm late init
  drm/amdgpu/dpm: don't add pwm attributes if DPM is disabled
  drm/radeon/dpm: don't add pwm attributes if DPM is disabled

The revert dance could use some explanation: we had stuff fixed in
-next, and initially backported one commit to v4.3. Now, turns out we
need more fixes, and we could cherry-pick them all without conflicts if
we reverted the backported one first. So did that to not have to edit
and backport them all.

* tag 'drm-intel-fixes-2015-10-16' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: Add primary plane to mask if it's visible
  drm/i915: Move sprite/cursor plane disable to intel_sanitize_crtc()
  drm/i915: Assign hwmode after encoder state readout
  Revert "drm/i915: Add primary plane to mask if it's visible"
  drm/i915: Deny wrapping an userptr into a framebuffer
  drm/i915: Enable DPLL VGA mode before P1/P2 divider write
  drm/i915: Restore lost DPLL register write on gen2-4
  drm/i915: Flush pipecontrol post-sync writes
  drm/i915: Fix kerneldoc for i915_gem_shrink_all

Currently we do not validate rtas.entry before calling enter_rtas(). This
leads to a kernel oops when user space calls rtas system call on a powernv
platform (see below). This patch adds code to validate rtas.entry before
making enter_rtas() call.

  Oops: Exception in kernel mode, sig: 4 [#1]
  SMP NR_CPUS=1024 NUMA PowerNV
  task: c000000004294b80 ti: c0000007e1a78000 task.ti: c0000007e1a78000
  NIP: 0000000000000000 LR: 0000000000009c14 CTR: c000000000423140
  REGS: c0000007e1a7b920 TRAP: 0e40   Not tainted  (3.18.17-340.el7_1.pkvm3_1_0.2400.1.ppc64le)
  MSR: 1000000000081000 <HV,ME>  CR: 00000000  XER: 00000000
  CFAR: c000000000009c0c SOFTE: 0
  NIP [0000000000000000]           (null)
  LR [0000000000009c14] 0x9c14
  Call Trace:
  [c0000007e1a7bba0] [c00000000041a7f4] avc_has_perm_noaudit+0x54/0x110 (unreliable)
  [c0000007e1a7bd80] [c00000000002ddc0] ppc_rtas+0x150/0x2d0
  [c0000007e1a7be30] [c000000000009358] syscall_exit+0x0/0x98

Cc: stable@vger.kernel.org # v3.2+
Fixes: 55190f88 ("powerpc: Add skeleton PowerNV platform")
Reported-by: NAGESWARA R. SASTRY <nasastry@in.ibm.com>
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
[mpe: Reword change log, trim oops, and add stable + fixes]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Just one fix from Ilia to resolve various issues that have resulted from
buffer eviction.

* 'linux-4.3' of git://anongit.freedesktop.org/nouveau/linux-2.6:
  drm/nouveau/gem: return only valid domain when there's only one

On nv50+, we restrict the valid domains to just the one where the buffer
was originally created. However after the buffer is evicted to system
memory, we might move it back to a different domain that was not
originally valid. When sharing the buffer and retrieving its GEM_INFO
data, we still want the domain that will be valid for this buffer in a
pushbuf, not the one where it currently happens to be.

This resolves fdo#92504 and several others. These are due to suspend
evicting all buffers, making it more likely that they temporarily end up
in the wrong place.

Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92504Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>