When executing in a PCI passthrough based virtuzliation environemnt, the
hypervisor will usually attempt to send a PCIe bus reset signal to the
ASIC when the VM reboots. In this scenario, the card is not correctly
initialized, but we still consider it to be posted. Therefore, in a
passthrough based environemnt we should always post the card to guarantee
it is in a good state for driver initialization.

However, if we are operating in SR-IOV mode it is up to the GIM driver
to manage the asic state, therefore we should not post the card (and
shouldn't be able to do it either).

v2: add missing semi-colon
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Andres Rodriguez <andres.rodriguez@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Seems to cause problems for some older hardware. Kudos to Thom Kouwenhoven
for working a lot with the PLLs and figuring this out.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Seems r600/r700 does not like hard reset while freezing for hibernation
(regression due to 274ad65c which itself
is a fix for hibernation on some GPU families). Until i can debug further
issue with r600, let just disable this for r600/r700 as they are very
similar family and bug affecting one likely affect the other.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Merge tag 'drm-amdkfd-fixes-2016-06-03' of git://people.freedesktop.org/~gabbayo/linux into drm-fixes

* tag 'drm-amdkfd-fixes-2016-06-03' of git://people.freedesktop.org/~gabbayo/linux:
  drm/amdkfd: print once about mem_banks truncation
  drm/amdkfd: destroy dbgmgr in notifier release
  drm/amdkfd: unbind only existing processes

* 'fixes-for-v4.7-rc3' of http://git.agner.ch/git/linux-drm-fsl-dcu:
  drm/fsl-dcu: use flat regmap cache

This just fixes a warning when you disable powerplay.
Signed-off-by: Dave Airlie <airlied@redhat.com>

Mostly memory leak and firmware leak fixes for amdgpu.  A bit bigger than
usual since this is several weeks worth of fixes.

* 'drm-fixes-4.7' of git://people.freedesktop.org/~agd5f/linux: (28 commits)
  drm/amd/powerplay: delete useless code as pptable changed in vbios.
  drm/amd/powerplay: fix bug visit array out of bounds
  drm/amdgpu: fix smu ucode memleak (v2)
  drm/amdgpu: add release firmware for cgs
  drm/amdgpu: fix tonga smu_fini mem leak
  drm/amdgpu: fix fiji smu fini mem leak
  drm/amdgpu: fix cik sdma ucode memleak
  drm/amdgpu: fix sdma24 ucode mem leak
  drm/amdgpu: fix sdma3 ucode mem leak
  drm/amdgpu: fix uvd fini mem leak
  drm/amdgpu: fix gfx 7 ucode mem leak
  drm/amdgpu: fix gfx8 ucode mem leak
  drm/amdgpu: fix missing free wb for cond_exec
  drm/amdgpu: fix memleak in pptable_init
  drm/amdgpu: fix mem leak in atombios
  drm/amdgpu: fix mem leak in pplib/hwmgr
  drm/amdgpu: fix mem leak in smumgr
  drm/amdgpu: add pipeline sync while vmid switch in same ctx
  drm/amdgpu: vBIOS post only call when mem_size zero
  drm/amdgpu: modify sdma start sequence
  ...

* 'msm-fixes-4.7-rc3' of git://people.freedesktop.org/~robclark/linux:
  drm/msm: fix potential submit error path issue
  drm/msm: fix some crashes in submit fail path
  drm/msm: deal with exhausted vmap space better

The vbios table changed so this code is useless now.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Properly release the smu ucode in powerplay.

v2: agd: add polaris as well
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Powerplay uses cgs to load the firmware so add a function
to release it as well to avoid leaking it on driver unload.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Since vmid-mgr supports vmid sharing in one vm, the same ctx could
get different vmids for two emits without vm flush, vm_flush could
be done in another ring.
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

should fist halt engine, and then doing the register
programing, and later unhalt engine, and finally run
ring_test.

this help fix reloading driver hang issue of SDMA
ring

original sequence is wrong for it programing engine
after unhalt, which will lead to fault behavior when
doing driver reloading after unloaded.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This help fix reloading driver hang issue of SDMA
ring
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This help fix reloading driver hang issue of SDMA
ring
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

We need to release the firmware on driver tear down.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

1,should use late_fini to kfree all resource otherwise
the released pointer maybe accessed in IRQ ip fini routine.

2,hwmgr should not be kfree by pem_fini which is invoked
by hw fini path.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This implements late_init support for powerplay.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This give IP modules an optional late cleanup
function.  This is needed to handle tricky inter-module
dependencies during tear down.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Exclude AVFS related fields when update powertune table to hw.
The driver shouldn't set them directly.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

fix the raster config setting for different iceland configs.
Signed-off-by: Ken Wang <Qingqing.Wang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This pull request brings in vblank/pageflip fixes I had hoped to see
merged before 4.7rc1, plus two new fixes that have come in since then.

* tag 'drm-vc4-fixes-2016-06-06' of github.com:anholt/linux:
  drm/vc4: Make pageflip completion handling more robust.
  drm/vc4: Fix ioctl permissions for render nodes.
  drm/vc4: Return -EBUSY if there's already a pending flip event.
  drm/vc4: Fix drm_vblank_put/get imbalance in page flip path.
  drm/vc4: Fix get_vblank_counter with proper no-op for Linux 4.4+

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Fixes for two issues reported by KASAN, a display engine hang due to
incorrect BIOS table parsing, and incorrect LTC interrupt handling on
Maxwell which could lead to a never-ending interrupt storm.

* 'linux-4.7' of git://github.com/skeggsb/linux:
  drm/nouveau/disp/sor/gm107: training pattern registers are like gm200
  drm/nouveau/disp/sor/gf119: both links use the same training register
  drm/nouveau/core: swap the order of imem/fb
  drm/nouveau/fbcon: fix out-of-bounds memory accesses
  drm/nouveau/gr/gf100-: update sm error decoding from gk20a nvgpu headers
  drm/nouveau/ltc/gm107-: fix typo in the address of NV_PLTCG_LTC0_LTS0_INTR
  drm/nouveau/bios/disp: fix handling of "match any protocol" entries

Using flat regmap cache instead of RB-tree to avoid the following
lockdep warning on driver load:
WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:2755 lockdep_trace_alloc+0x15c/0x160()
DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))

The RB-tree regmap cache needs to allocate new space on first
writes. However, allocations in an atomic context (e.g. when a
spinlock is held) are not allowed. The function regmap_write
calls map->lock, which acquires a spinlock in the fast_io case.
Since the FSL DCU driver uses MMIO, the regmap bus of type
regmap_mmio is being used which has fast_io set to true.

Use flat regmap cache and specify max register to be large
enouth to cover all registers available in LS1021a and Vybrids
register space.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org