- 31 Jan, 2019 5 commits
-
-
Yunfei Dong authored
Vdec: Using standard CCF interface to set parent clock and clock rate in dtsi and using common interface to open/close video decoder clock. Venc: Using standard CCF interface to set parent clock in dtsi and using common interface to open/close video encoder clock. Signed-off-by:
Yunfei Dong <yunfei.dong@mediatek.com> Signed-off-by:
Qianqian Yan <qianqian.yan@mediatek.com> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Yunfei Dong authored
Fix MTK binding document for MT8173 dtsi changed in order to use standard CCF interface. MT8173 SoC from Mediatek. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Steve Longerbeam authored
Upstream must be stopped immediately after receiving the last EOF and before disabling the IDMA channel. This can be accomplished by moving upstream stream off to just after receiving the last EOF completion in prp_stop(). For symmetry also move upstream stream on to end of prp_start(). This fixes a complete system hard lockup on the SabreAuto when streaming from the ADV7180, by repeatedly sending a stream off immediately followed by stream on: while true; do v4l2-ctl -d1 --stream-mmap --stream-count=3; done Eventually this either causes the system lockup or EOF timeouts at all subsequent stream on, until a system reset. The lockup occurs when disabling the IDMA channel at stream off. Stopping the video data stream entering the IDMA channel before disabling the channel itself appears to be a reliable fix for the hard lockup. Fixes: f0d9c892 ("[media] media: imx: Add IC subdev drivers") Reported-by:
Gaël PORTAY <gael.portay@collabora.com> Tested-by:
Steve Longerbeam <slongerbeam@gmail.com> Cc: stable@vger.kernel.org # for 4.13 and up Signed-off-by:
-
Steve Longerbeam authored
Move upstream stream off to just after receiving the last EOF completion and disabling the CSI (and thus before disabling the IDMA channel) in csi_stop(). For symmetry also move upstream stream on to beginning of csi_start(). Doing this makes csi_s_stream() more symmetric with prp_s_stream() which will require the same change to fix a hard lockup. Signed-off-by:
-
Steve Longerbeam authored
Disable the CSI immediately after receiving the last EOF before stream off (and thus before disabling the IDMA channel). Do this by moving the wait for EOF completion into a new function csi_idmac_wait_last_eof(). This fixes a complete system hard lockup on the SabreAuto when streaming from the ADV7180, by repeatedly sending a stream off immediately followed by stream on: while true; do v4l2-ctl -d4 --stream-mmap --stream-count=3; done Eventually this either causes the system lockup or EOF timeouts at all subsequent stream on, until a system reset. The lockup occurs when disabling the IDMA channel at stream off. Disabling the CSI before disabling the IDMA channel appears to be a reliable fix for the hard lockup. Fixes: 4a34ec8e ("[media] media: imx: Add CSI subdev driver") Reported-by:
-
- 26 Jan, 2019 3 commits
-
-
Mauro Carvalho Chehab authored
drivers/media/platform/vicodec/vicodec-core.c:drivers/media/platform/vicodec/vicodec-core.c:210:23: warning: symbol 'get_next_header' was not declared. Should it be static? drivers/media/platform/vicodec/vicodec-core.c:210:23: warning: no previous prototype for 'get_next_header' [-Wmissing-prototypes] enum vb2_buffer_state get_next_header(struct vicodec_ctx *ctx, u8 **pp, u32 sz) ^~~~~~~~~~~~~~~ Signed-off-by: -
Dafna Hirschfeld authored
Make sure that the pointer to the compressed frame does not get out of the buffer. Signed-off-by:
Dafna Hirschfeld <dafna3@gmail.com> Signed-off-by:
-
Dafna Hirschfeld authored
If the the queues are not streaming then the first resolution change is handled in the buf_queue callback. The following resolution change events are handled in job_ready. Signed-off-by:
-
- 25 Jan, 2019 32 commits
-
-
Dafna Hirschfeld authored
Keep the fwht header in separated field from the data. Refactor job_ready to use a new function 'get_next_header' Signed-off-by:
-
Dafna Hirschfeld authored
Add flags indicating the pixel encoding - yuv/rgb/hsv to fwht header and to the pixel info. Use it to enumerate the supported pixel formats. Signed-off-by:
-
Dafna Hirschfeld authored
Use 3 bits for the number of components mask in the fwht header flags Signed-off-by:
-
Dafna Hirschfeld authored
Add support for the selection api for the crop and compose targets. The driver rounds up the coded width and height such that all planes dimensions are multiple of 8. Signed-off-by:
-
Dafna Hirschfeld authored
Add the field 'num_planes' to 'v4l2_fwht_pixfmt_info' struct. Signed-off-by:
-
Hans Verkuil authored
The "Codec Interface" chapter is poorly named since codecs are just one use-case of the Memory-to-Memory Interface. Rename it and clean up the text a bit. Signed-off-by:
Tomasz Figa <tfiga@chromium.org> Signed-off-by:
-
Hans Verkuil authored
The teletext interface has been dead for years now, just remove it. Signed-off-by:
-
Hans Verkuil authored
We never had an effect interface, and if you want to do such things you use the mem2mem interface instead. Just drop this from the spec. Signed-off-by:
-
Hans Verkuil authored
Fix the outdated irq example code. It is under an #ifdef TODO so it is never actually compiled and this code was never compiled. Signed-off-by:
-
Stanimir Varbanov authored
The zero timestamp is really valid so fix that mistake by dropping the code which checks for zero timestamp. Reviewed-by:
Alexandre Courbot <acourbot@chromium.org> Tested-by:
Stanimir Varbanov <stanimir.varbanov@linaro.org> Signed-off-by:
-
Stanimir Varbanov authored
This corrects clock frequency table rates to be in sync with video clock controller frequency table. Reviewed-by:
-
Stanimir Varbanov authored
This correct maximum hardware load constant in per SoC resources for sdm845 aka Venus v4. Reviewed-by:
-
Stanimir Varbanov authored
By historical reasons we defined firmware memory size to be 6MB even that the firmware size for all supported Venus versions is 5MBs. Correct that by compare the required firmware size returned from mdt loader and the one provided by DT reserved memory region. We proceed further if the required firmware size is smaller than provided by DT memory region. Reviewed-by:
-
Akinobu Mita authored
Set initial try format with default configuration instead of current one. Fixes: 8d3b307a ("media: ov2640: make VIDIOC_SUBDEV_G_FMT ioctl work with V4L2_SUBDEV_FORMAT_TRY") Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Dan Carpenter authored
This function prints an error message on success. I don't have the hardware, I just noticed this while reading the code. Fixes: 8b99312b ("[media] Add v4l2 subdev driver for S5K4ECGX sensor") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Akinobu Mita authored
This driver sets initial frame width and height to 0x0, which is invalid. So set it to selection rectangle bounds instead. This is detected by v4l2-compliance detected. Cc: Enrico Scholz <enrico.scholz@sigma-chemnitz.de> Cc: Michael Grzeschik <m.grzeschik@pengutronix.de> Cc: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by:
-
Akinobu Mita authored
This driver doesn't set all members of mbus format field when the VIDIOC_SUBDEV_{S,G}_FMT ioctls are called. This is detected by v4l2-compliance. Cc: Enrico Scholz <enrico.scholz@sigma-chemnitz.de> Cc: Michael Grzeschik <m.grzeschik@pengutronix.de> Cc: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: -
Akinobu Mita authored
The VIDIOC_SUBDEV_G_FMT ioctl for this driver doesn't recognize V4L2_SUBDEV_FORMAT_TRY and always works as if V4L2_SUBDEV_FORMAT_ACTIVE is specified. Cc: Enrico Scholz <enrico.scholz@sigma-chemnitz.de> Cc: Michael Grzeschik <m.grzeschik@pengutronix.de> Cc: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by:
-
Akinobu Mita authored
This driver doesn't set all members of mbus format field when the VIDIOC_SUBDEV_{S,G}_FMT ioctls are called. This is detected by v4l2-compliance. Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: -
Akinobu Mita authored
The VIDIOC_SUBDEV_G_FMT ioctl for this driver doesn't recognize V4L2_SUBDEV_FORMAT_TRY and always works as if V4L2_SUBDEV_FORMAT_ACTIVE is specified. Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Akinobu Mita authored
This adds log_status ioctl and event interface for mt9m001's v4l2 controls. Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Akinobu Mita authored
Register a sub-device to the asynchronous subdevice framework, and also create subdevice device node. Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Akinobu Mita authored
Create a source pad and set the media controller type to the sensor. Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Akinobu Mita authored
Remove remaining soc_camera specific code and drop soc_camera dependency from this driver. Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Akinobu Mita authored
Switch s_power() callback to runtime PM framework. This also removes soc_camera specific power management code and introduces reset and standby gpios instead. Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Akinobu Mita authored
Introduce multi_reg_write() to write multiple registers to the device and use it where possible. Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Akinobu Mita authored
Add of_match_table for the MT9M001 CMOS image sensor. Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Akinobu Mita authored
Sort header block alphabetically for easy maintenance. Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Akinobu Mita authored
Replace GPL license statements with SPDX license identifiers (GPL-2.0). This also fixes MODULE_LICENSE() ident to match the actual license text. Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Akinobu Mita authored
Add device tree binding documentation for the MT9M001 CMOS image sensor. Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Akinobu Mita authored
Copy the soc_camera based driver in v4l2 sensor driver directory. This commit just copies the original file without modifying it. Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Ben Kao authored
We use put_unaligned_be16() to be simplified for setting register address in ov8856_read_reg() and use sizeof() to be better suited for bytes copying. Signed-off-by:
Ben Kao <ben.kao@intel.com> Signed-off-by:
-
