- 03 Oct, 2019 7 commits
-
-
Kuninori Morimoto authored
snd_soc_limit_volume() is finding snd_kcontrol by using original coding, but we already have snd_soc_card_get_kcontrol(). Let's use existing function. Signed-off-by:
Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/87y2y3afgd.wl-kuninori.morimoto.gx@renesas.comSigned-off-by:
Mark Brown <broonie@kernel.org>
-
Kuninori Morimoto authored
card->rtd_num is used to count rtd. Initialize it at snd_soc_instantiate_card() is very natural and less confusion. Signed-off-by:
-
Kuninori Morimoto authored
dai / component related resources are created when component is registered, and it will be freed when component was unregistered. These resources are not re-used after that. This means, we can use devm_xxx for dai / component, without thinking about kfree(). This patch uses devm_xxx for these. Signed-off-by:
-
Kuninori Morimoto authored
ALSA needs to setup shortname, longname, and driver. These methods are very similar. This patch adds new soc_setup_card_name() and setup these. Signed-off-by:
-
Kuninori Morimoto authored
It is easy to read code if it is cleanly using paired function/naming, like start <-> stop, register <-> unregister, etc, etc. But, current ALSA SoC code is very random, unbalance, not paired, etc. It is easy to create bug at the such code, and it will be difficult to debug. soc_cleanup_card_resources() (a) which is paired function of snd_soc_instantiate_card() (A) is calling soc_remove_dai_links() (*) to remove card related resources, but it is breaking add/remove balance (B)(b)(C)(c)(D)(d), in other words these should be called from soc_cleanup_card_resources() (a) from balance point of view. More headacke is that it is using original removing method for dai_link even though we already have snd_soc_remove_dai_link() which is the function for it (d). This patch removes snd_soc_remove_dai_links() and balance up code. static void soc_remove_dai_links(...) { ... (b) soc_remove_link_dais(card); (c) soc_remove_link_components(card); for_each_card_links_safe(card, link, _link) { ... /* it should use snd_soc_remove_dai_link() here */ (d) list_del(&link->list); } } (a) static int soc_cleanup_card_resources(...) { ... /* remove and free each DAI */ (*) soc_remove_dai_links(card); ... } (A) static int snd_soc_instantiate_card(struct snd_soc_card *card) { ... /* add predefined DAI links to the list */ for_each_card_prelinks(card, i, dai_link) (B) snd_soc_add_dai_link(card, dai_link); ... /* probe all components used by DAI links on this card */ (C) ret = soc_probe_link_components(card); ... /* probe all DAI links on this card */ (D) ret = soc_probe_link_dais(card); ... } Signed-off-by: -
Kuninori Morimoto authored
Current rtd, rtd->dev, rtd->codec_dais are created by normal kzalloc(), but we want to use devm_kzalloc() as much as possible. Created rtd->dev is registered by device_register() at soc_new_pcm_runtime(), and it will be freed at soc_free_pcm_runtime() by device_unregister(). This means, if we can use devm_kzalloc(rtd->dev, xxx) for rtd / rtd->codec_dais, all these are automatically freed via soc_free_pcm_runtime(). This patch uses devm_kzalloc(rtd->dev, xxx) for rtd / rtd->codec_dais. Signed-off-by:
-
kbuild test robot authored
sound/soc/codecs/tas2770.c:796:3-8: No need to set .owner here. The core will do it. Remove .owner field if calls are used which set it automatically Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci Fixes: 1a476abc ("tas2770: add tas2770 smart PA kernel driver") CC: Frank Shi <shifu0704@thundersoft.com> Signed-off-by:
kbuild test robot <lkp@intel.com> Link: https://lore.kernel.org/r/20191001175504.ufhyxh66psrht42k@332d0cec05f4Signed-off-by:
-
- 02 Oct, 2019 4 commits
-
-
Sylwester Nawrocki authored
Rename arndale_rt5631.c to just arnddale.c as we support other CODECs than RT5631. While at it replace spaces in Kconfig with tabs. Reviewed-by:
Charles Keepax <ckeepax@opensource.cirrus.com> Acked-by:
Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Link: https://lore.kernel.org/r/20191002105652.24821-3-s.nawrocki@samsung.comSigned-off-by:
-
Sylwester Nawrocki authored
The Arndale boards come with different types of the audio daughter board. In order to support the WM1811 one we add new definition of an ASoC card which will be registered when the driver matches on "samsung,arndale-wm1811" compatible. There is no runtime detection of the audio daughter board type at the moment, compatible string of the audio card needs to be adjusted in DT, e.g. by the bootloader, depending on actual audio board (CODEC) used. Reviewed-by:
-
Sylwester Nawrocki authored
There is only one DAI link so we can drop an unnecessary loop statement. Use card->dai_link in place of direct static arndale_rt5631_dai[] array dereference as a prerequisite for adding support for other CODECs. Unnecessary assignment of dai_link->codecs->name to NULL is removed. Reviewed-by:
-
Mark Brown authored
-
- 01 Oct, 2019 29 commits
-
-
Liam Girdwood authored
Helps with FW debug as it provides DSP IPC processing context. Signed-off-by:
Liam Girdwood <liam.r.girdwood@linux.intel.com> Signed-off-by:
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20190927200538.660-13-pierre-louis.bossart@linux.intel.comSigned-off-by:
-
Marcin Rajwa authored
This patch prevents the reset of host period bytes and uses no_stream_position to record requests for stream position. Signed-off-by:
Marcin Rajwa <marcin.rajwa@linux.intel.com> Signed-off-by:
-
Marcin Rajwa authored
The host period bytes value needs to be passed to firmware. However current implementation uses this field for different purpose - to indicate whether FW should send stream position to the host. Therefore this patch introduces another field "no_stream_position", a boolean value aimed to store information about position tracking. This way host_period_bytes preserves its original value. Signed-off-by:
-
Ranjani Sridharan authored
fw_ready should be a mandatory op. Make sure fw_ready ops is set during probe. Signed-off-by:
Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by:
-
Liam Girdwood authored
Add config option to prevent DSP entering D3 after any FW exception. This can then be used to dump FW context for debug. Signed-off-by:
-
Pierre-Louis Bossart authored
In a number of debug cases, the DMA-based trace can add problems (e.g. with HDaudio channel allocation). It also generates additional traffic on the bus and if the DMA handling is unreliable will prevent audio use-cases from working normally. Using the trace also requires tools to be installed on the target. The trace can be instead handled as dynamic debug. We can use a Kconfig to force the trace to be enabled in all cases, or use a module parameter to enable it on a need-basis, e.g. by setting "options snd_sof sof_debug=0x1" in a /etc/modprobe.d file. Signed-off-by:
-
Jaska Uimonen authored
When removing sof module the support_button_press function will oops because hp_jack pointer is not checked for NULL. So add a check to fix this. Signed-off-by:
Jaska Uimonen <jaska.uimonen@intel.com> Signed-off-by:
-
Jaska Uimonen authored
When removing sof module the rt5682 jack handler will oops if jack detection is not disabled. So add remove function, which disables the jack detection. Signed-off-by:
-
Jaska Uimonen authored
Implement NULL handler in set_jack function to disable irq's. Signed-off-by:
-
Bard Liao authored
dmic map can only be added when dmic dai link is present. Signed-off-by:
Bard Liao <yung-chuan.liao@linux.intel.com> Signed-off-by:
-
Ranjani Sridharan authored
There is a known issue on some Intel platforms which causes pause/release to run into xrun's during capture usecases. The suggested workaround to address the issue is to disable the entry of lower power L1 state in the physical DMI link when there is a capture stream open. Signed-off-by:
-
Liam Girdwood authored
FW mailbox offset was not set before use and HDR size was not validated. Fix this. Signed-off-by:
-
Kai Vehmanen authored
The "snd_pcm_substream" handle was not initialized properly in hda-loader.c for firmware load. When the HDA DMAs were used to load the firmware, the interrupts related to firmware load also triggered calls to snd_sof_pcm_period_elapsed() on a non-existent ALSA PCM stream. This caused runtime kernel warnings from pcm_lib.c:snd_pcm_period_elapsed(). Signed-off-by:
Kai Vehmanen <kai.vehmanen@linux.intel.com> Signed-off-by:
-
Pan Xiuli authored
The old STOP sequence is: 1. stop DMA 2. send STOP ipc If delay happen before the steps 1 and 2, the DMA buffer will be empty in short time and cause pipeline xrun then stop the pipeline. Then the step 2 ipc stop will return error as pipeline is already stopped. Suggested change to avoid the issue is to switch the order of steps 1 and 2 for the stop sequence. Signed-off-by:
Pan Xiuli <xiuli.pan@linux.intel.com> Signed-off-by:
-
Kai Vehmanen authored
Fix a bug in sof_pcm_hw_free() where some cleanup actions were skipped if STREAM_PCM_FREE IPC was already successfully sent to DSP when the stream was stopped or suspended. This is incorrect as hw_free should clean up also other resources, including pcm lib page allocations, period elapsed work queue and call to platform hw_free. Fixes: c29d96c3b9b4 ("ASoC: SOF: reset DMA state in prepare") Signed-off-by: -
Keyon Jie authored
We are using sof_parse_word_tokens() to parse tokens with bool/byte/short/word tuple types, here add the missing check, to fix the parsing failure at byte/bool tuple types. Signed-off-by:
Keyon Jie <yang.jie@linux.intel.com> Signed-off-by:
-
Pierre-Louis Bossart authored
When we fail to boot the firmware, we encounter a kernel oops in hda_dsp_get_registers(), which is called conditionally in hda_dsp_dump() when the sdev_>boot_complete flag is set. Setting this flag _after_ dumping the data fixes the issue and does not change the programming flow. Signed-off-by:
-
Charles Keepax authored
Some Madera CODECs have a third MCLK pin allow this to be sourced for the FLLs and system clocks. Signed-off-by:
-
Li Xu authored
Fix potential NULL pointer dereference for alg_region in wm_adsp_buffer_parse_legacy. In practice this can never happen as loading the firmware should have failed at the wm_adsp2_setup_algs stage, however probably better for the code to be robust against future changes and this is more helpful for static analysis. Signed-off-by:
Li Xu <li.xu@cirrus.com> Signed-off-by:
-
Sathyanarayana Nujella authored
Below Oops is caused in a system which uses ACPI instead of device node: of_get_named_gpiod_flags: can't parse 'maxim,reset-gpio' property of node '(null)[0]' BUG: kernel NULL pointer dereference, address: 0000000000000010 This patch avoids NULL pointer deferencing by adding a check before parsing and initializes to make reset-gpio pin as invalid. Signed-off-by:
Sathyanarayana Nujella <sathyanarayana.nujella@intel.com> Signed-off-by:
Jairaj Arava <jairaj.arava@intel.com> Link: https://lore.kernel.org/r/1569702150-11976-1-git-send-email-sathyanarayana.nujella@intel.comSigned-off-by:
-
Frank Shi authored
add tas2770 smart PA kernel driver Signed-off-by:
Frank Shi <shifu0704@thundersoft.com> Link: https://lore.kernel.org/r/1568962709-19185-2-git-send-email-shifu0704@thundersoft.comSigned-off-by:
-
Peter Ujfalusi authored
On stream stop currently we stop the DMA first followed by the CPU DAI. This can cause underflow (playback) or overflow (capture) on the DAI side as the DMA is no longer feeding data while the DAI is still active. It can be observed easily if the DAI side does not have FIFO (or it is disabled) to survive the time while the DMA is stopped, but still can happen on relatively slow CPUs when relatively high sampling rate is used: the FIFO is drained between the time the DMA is stopped and the DAI is stopped. It can only fixed by using different sequence within trigger for 'stop' and 'start': case SNDRV_PCM_TRIGGER_START: case SNDRV_PCM_TRIGGER_RESUME: case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: Trigger order: dai_link, DMA, CPU DAI then the codec case SNDRV_PCM_TRIGGER_STOP: case SNDRV_PCM_TRIGGER_SUSPEND: case SNDRV_PCM_TRIGGER_PAUSE_PUSH: Trigger order: codec, CPU DAI, DMA then dai_link Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by:
-
Shengjiu Wang authored
There is error "aplay: pcm_write:2023: write error: Input/output error" on i.MX8QM/i.MX8QXP platform for S24_3LE format. In i.MX8QM/i.MX8QXP, the DMA is EDMA, which don't support 24bit sample, but we didn't add any constraint, that cause issues. So we need to query the caps of dma, then update the hw parameters according to the caps. Signed-off-by:
Shengjiu Wang <shengjiu.wang@nxp.com> Acked-by:
Nicolin Chen <nicoleotsuka@gmail.com> Link: https://lore.kernel.org/r/b6a4de2bbf960ef291ee902afe4388bd0fc1d347.1569493933.git.shengjiu.wang@nxp.comSigned-off-by:
-
Shengjiu Wang authored
When set the runtime hardware parameters, we may need to query the capability of DMA to complete the parameters. This patch is to Extract this operation from dmaengine_pcm_set_runtime_hwparams function to a separate function snd_dmaengine_pcm_refine_runtime_hwparams, that other components which need this feature can call this function. Signed-off-by:
-
Shengjiu Wang authored
The ASRC support 24bit/16bit/8bit input width, which is data width, not slot width. For the S20_3LE format, the data with is 20bit, slot width is 24bit, if we set ASRMCR1n.IWD to be 24bits, the result is the volume is lower than expected, it likes 24bit data right shift 4 bits So replace S20_3LE with S24_3LE in supported list and add S8 format in TX supported list Signed-off-by:
-
Shengjiu Wang authored
snd_pcm_format_t is more formal than enum asrc_word_width, which has two property, width and physical width, which is more accurate than enum asrc_word_width. So it is better to use in(out)put_format instead of in(out)put_word_width. Signed-off-by:
-
Lars-Peter Clausen authored
The adau1761 has a automatic level control block that can adjust the gain for the differential input PGA. This patch adds ALSA controls for enabling and changing the parameter settings for the ALC. Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
Alexandru Ardelean <alexandru.ardelean@analog.com> Link: https://lore.kernel.org/r/20190926115012.24049-2-alexandru.ardelean@analog.comSigned-off-by:
-
Lars-Peter Clausen authored
The PGA Slew Time control allows to configure the rate with which the PGA gain control ramps up/down to the target setting. The PGA slew control is done via the ALC Control 0 register. There are 2 bits on that reg, that control PGA slew time, while the other bits control parts of the ALC (automatic level control) block. Signed-off-by:
-
Daniel Baluta authored
For a sound card ignore_machine means that existing FEs links should be ignored and existing BEs links should be overridden with some information from the matching component driver. Current code make some confusions about this so fix it! Signed-off-by:
Daniel Baluta <daniel.baluta@nxp.com> Link: https://lore.kernel.org/r/20190925183358.11955-1-daniel.baluta@nxp.comSigned-off-by:
-
