A core in EVA mode can have any possible segment mapping, so the
default free_initmem_default() function may not always work as expected.
Therefore, add a callback that platforms can use to free up the init section.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

The MIPS *Aptiv family uses bit 28 in Config5 CP0 register to
indicate whether the core supports EVA or not.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

This will allow platforms to use an alternative way to get
the physical address of a symbol.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

When flushing the icache, make sure the address limit is correct
so the appropriate 'cache' instruction will be used. This has no
impact on cores operating in non-eva mode. However, when EVA is
enabled, we ensure that 'cache' will be used instead of 'cachee'.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Add EVA cache flushing functions similar to non-EVA configurations.
Because the cache may or may not contain user virtual addresses, we
need to use the 'cache' or 'cachee' instruction based on whether we
flush the cache on behalf of kernel or user respectively.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Build code to invalidate an address range in the  instruction cache
using the Hit Invalidate cache operation.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

EVA does not have FPU specific instructions for reading or writing
FPU registers from userspace memory.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

A MIPS specific csum_and_copy_from_user function is necessary because
the generic one from include/net/checksum.h will not work for EVA.
This is because the generic one will link to symbols from lib/checksum.c
which are not EVA aware.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

In EVA mode, different instructions need to be used to read/write
from kernel and userland. In non-EVA mode, there is no functional
difference. The current address limit is checked to decide the
type of operation that will be performed.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Use EVA specific functions to read and write data to
user address space.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

In preparation for EVA support, we use a macro to build the
__csum_partial_copy_user main code so it can be shared across
multiple implementations. EVA uses the same code but it replaces
the load/store/prefetch instructions with the EVA specific ones
therefore using a macro avoids unnecessary code duplications.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Each load/store macro always adds an entry to the __ex_table
using the EXC macro. There are cases where a load instruction may
never fail such as when we are sure the load happens in the kernel
address space. Therefore, we merge these the EXC and LOADX/STOREX
macros into a single one. We also expand the argument list in the EXC
macro to make the macro more flexible. The extra 'type' argument is not
used by this commit, but it will be used when EVA support is added to
memcpy.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

The 'copy_user' symbol can be used to copy from or to
userland so we will use two different symbols for these
operations. This makes no difference in the existing code,
but when the core is operating in EVA mode, different instructions
need to be used to read and write to userland address space.
The old function has also been renamed to 'copy_kernel' to denote
that it is suitable for copy data to and from kernel space.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Handle unaligned accesses when we access userspace memory
EVA mode.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Use the load/store instruction wrappers from asm/asm.h to
perform such operations when operating in EVA mode.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

The str*_user functions are used to securely access NULL terminated
strings from userland. Therefore, it's necessary to use the appropriate
EVA function. However, if the string is in kernel space, then the normal
instructions are being used to access it. The __str*_kernel_asm and
__str*_user_asm symbols are the same for non-EVA mode so there is no
functional change for the non-EVA kernels.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Use the EVA specific functions from memcpy.S to perform
userspace operations. When get_fs() == get_ds() the usual load/store
instructions are used because the destination address is located in
the kernel address space region. Otherwise, the EVA specifc load/store
instructions are used which will go through th TLB to perform the virtual
to physical translation for the userspace address.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

The {get,put}_user_asm functions can be used to load data from
kernel or the user address space so rename them to avoid
confusion.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Use the EVA instruction wrappers from asm.h to perform
read/write operations from userland.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

ulb, ulh, ulw are macros which emulate unaligned access for MIPS.
However, no such macros exist for EVA mode, so the only way to do
EVA unaligned accesses is in the ADE exception handler. As a result
of which, disable these macros for EVA.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Similar to __get_user_* functions, move common code to
__put_user_*_common so it can be shared among similar users.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

In preparation for EVA support, an instruction argument is needed
for the __get_user_asm{,_ll32} functions to allow instruction overrides in
EVA mode. Even though EVA only works for MIPS 32-bit, both codepaths are
changed (32-bit and 64-bit) for consistency reasons.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Build the __bzero function using the EVA load/store instructions
when operating in the EVA mode. This function is only used when
accessing user code so there is no need to build two distinct symbols
for user and kernel operations respectively.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Build the __bzero symbol using a macor. In EVA mode we will
need to use similar code to do the userspace load operations so
it is better if we use a macro to avoid code duplications.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Add copy_{to,from,in}_user when the CPU operates in EVA mode.
This is necessary so the EVA specific instructions can be used
to perform the virtual to physical translation for user space
addresses. We will use the non-EVA functions to read from kernel
if needed.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

The code can be shared between EVA and non-EVA configurations,
therefore use a macro to build it to avoid code duplications.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

In preparation for EVA support, the PREF macro is split into two
separate macros, PREFS and PREFD, for source and destination data
prefetching respectively.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Each load/store macro always adds an entry to the __ex_table
using the EXC macro. Therefore, these load/store macros are now merged
with the EXC one. The argument list is also expanded in order to make
the macro more flexible. The extra 'type' argument is not used by this
commit, but it will be used when the EVA support is added to the memcpy.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

In non-EVA mode, strncpy_from_user* aliases are used for the
strncpy_from_kernel* symbols since the code is identical. In EVA
mode, new strcpy_from_user* symbols are used which use the EVA
specific instructions to load values from userspace.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Build the __strncpy_from_user symbol using a macro. In EVA mode we will
need to use similar code to do the userspace load operations so
it is better if we use a macro to avoid code duplications.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

In non-EVA mode, strlen_user* aliases are used for the
strlen_kernel* symbols since the code is identical. In EVA
mode, new strlen_user* symbols are used which use the EVA
specific instructions to load values from userspace.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Build the __strlen_user symbol using a macro. In EVA mode we will
need to use similar code to do the userspace load operations so
it is better if we use a macro to avoid code duplications.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

In non-EVA mode, a strlen_user* alias is used for the
strlen_kernel* symbols since the code is identical. In EVA
mode, a new strlen_user* symbol is used which uses the EVA
specific instructions to load values from userspace.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Build the __strnlen_user symbol using a macro. In EVA mode we will
need to use similar code to do the userspace load operations so
it is better if we use a macro to avoid code duplications.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

When a breakpoint or trap happens when operating in kernel mode but
on users behalf (eg syscall) it is necessary to change the address
limit to KERNEL_DS so any address checking can be bypassed and print
the correct stack trace.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>