In case of a bi-directional transfer, receive DMA may complete in the
rcar-dmac driver before transmit DMA, due to scheduling latencies.
As the MSIOF driver waits for completion of the receive DMA only, it may
submit the next transmit DMA request before the previous one has
completed.

Make the driver more robust by waiting for the completion of both
receive and transmit DMA, when applicable.

Based on a patch in the BSP by Ryo Kataoka.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>

The correct form is "a high-level", so fix it accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

According to section 59.2.4 MSIOF Receive Mode Register 1 (SIRMDR1) in
the R-Car Gen3 datasheet Rev.1.00, the value of the SIRMDR1.SYNCAC bit
must match the value of the SITMDR1.SYNCAC bit.  However,
sh_msiof_spi_setup() changes only the latter.

Fix this by updating the SIRMDR1 register like the SITMDR1 register,
taking into account register bits that exist in SITMDR1 only.
Reported-by: Renesas BSP team via Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 7ff0b53c ("spi: sh-msiof: Avoid writing to registers from spi_master.setup()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@kernel.org>

SPI mem drivers should use spi_mem_set_drvdata() not spi_set_drvdata()
to store their private data. Using spi_set_drvdata() will mess the
spi -> spi-mem link up and cause a kernel panic at shutdown or
device removal time.

Fixes: 4120f8d1 ("mtd: spi-nor: Use the spi_mem_xx() API")
Reported-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Marek Vasut <marek.vasut+renesas@gmail.com> on R8A7791 Porter
Signed-off-by: Mark Brown <broonie@kernel.org>

Commit 5a686b2c ("spi: omap2-mcspi: Idle hardware during suspend
and resume") added calls for pm_runtime_force_suspend() and
pm_runtime_force_resume() to make sure spi is idled between
device_prepare() and device_complete().

But testing Linux next, I now noticed that we will get the following:

spi_master spi0: Failed to power device: -13

Looking at things more turns out we can just remove this non-standard
code. I was probably testing with some extra experimental patches
earlier when I thought we need pm_runtime_force_suspend() and
pm_runtime_force_resume().

Fixes: 5a686b2c ("spi: omap2-mcspi: Idle hardware during suspend
and resume")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

If pm_runtime_get_sync() fails we should call pm_runtime_put_noidle().
This is probably not a critical fix as we should only hit this when
things are broken elsewhere.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

resource_size() is dereferencing the res without checking that it is
not NULL, so we need to do the check before calling resource_size().

Fixes: b95cb394 ("spi: ti-qspi: Implement the spi_mem interface")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Since Linux v4.10 release (commit 1d9174fb "PM / Runtime: Defer
resuming of the device in pm_runtime_force_resume()"),
pm_runtime_force_resume() function doesn't runtime resume device if it was
not runtime active before system suspend. Thus, driver should not do any
register access after pm_runtime_force_resume() without checking the
runtime status of the device. To fix this issue, simply move
s3c64xx_spi_hwinit() call to s3c64xx_spi_runtime_resume() to ensure that
hardware is always properly initialized. This fixes Synchronous external
abort issue on system suspend/resume cycle on newer Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

Patch http://patchwork.ozlabs.org/patch/905205/ has been partially
applied, and changes to the bcm-qspi driver have been lost somehow
(probably due to a conflict when applying the patch).

Remove the ->spi_flash_read() bits from this driver to fix the build
error.

Fixes: c1f5ba70 ("spi: Get rid of the spi_flash_read() API")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This API has been replaced by the spi_mem_xx() one, its only user
(spi-nor) has been converted to spi_mem_xx() and all SPI controller
drivers that were implementing the ->spi_flash_xxx() hooks are also
implementing the spi_mem ones. So we can safely get rid of this API.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Tested-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

The spi_mem_xxx() API has been introduced to replace the
spi_flash_read() one. Make use of it so we can get rid of
spi_flash_read().

Note that using spi_mem_xx() also simplifies the code because this API
takes care of using the regular spi_sync() interface when the optimized
->mem_ops interface is not implemented by the controller.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Tested-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

The spi_mem interface is meant to replace the spi_flash_read() one.
Implement the ->exec_op() method so that we can smoothly get rid of the
old interface.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Vignesh R <vigneshr@ti.com>
Tested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The spi_mem interface is meant to replace the ->spi_flash_read() one.
Implement the ->exec_op() method to ease removal of the old interface.

Not that ->spi_flash_read() is now implemented as a wrapper around the
new bcm_qspi_exec_mem_op() function so that we can easily get rid of
it when ->spi_flash_read() is removed.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Kamal Dasu <kdasu.kdev@gmail.com>
Tested-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Some SPI/QuadSPI controllers only expose a high-level SPI memory
interface, thus preventing any regular SPI transfers from being done.

In that case, SPI controller drivers can leave all ->transfer_xxx()
hooks empty and only implement the spi_mem_ops interface.

Adjust the core to allow such situations:
- extend spi_controller_check_ops() to accept situations where all
  ->transfer_xxx() pointers are NULL only if ->mem_ops != NULL
- make sure we do not initialize the SPI message queue if
  ctlr->transfer_one and ctlr->transfer_one_message are missing
- return -ENOTSUPP if someone tries to do a regular SPI transfer on
  a controller that does not support it
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Tested-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

Some controllers are exposing high-level interfaces to access various
kind of SPI memories. Unfortunately they do not fit in the current
spi_controller model and usually have drivers placed in
drivers/mtd/spi-nor which are only supporting SPI NORs and not SPI
memories in general.

This is an attempt at defining a SPI memory interface which works for
all kinds of SPI memories (NORs, NANDs, SRAMs).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Tested-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

I accidentally sent an early version of patch removing spi-bcm53xx
driver which got rid of .c and .h files *only*. I amended local commit
but forgot to re-format the patch.

This commit removes leftovers of dropped driver.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>

This driver was added by commit 0fc6a323 ("spi: bcm53xx: driver for
SPI controller on Broadcom bcma SoC") back in 2014. It was needed to
provide a minimal support for SPI controller on BCM5301X (AKA Northstar)
devices.

An alternative driver was added by Kamal in commit fa236a7e ("spi:
bcm-qspi: Add Broadcom MSPI driver") 2 years later. It supports the same
hardware but for some reason a new driver has been developed for it.

At this point the new driver supports: more modes, setting a speed,
setting bits per word and uses IRQs instead of polling. DTS file for
BCM5301X has also been updated in the commit 1c8f4065 ("ARM: dts:
BCM5301X: convert to iProc QSPI") - over a year ago.

That explained I see no reason to keep the old driver alive.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>

clk_prepare_enable() can fail, so its return value should be checked and
acted upon.

Found by Linux Driver Verification project (linuxtesting.org).

Fixes: 3343b7a6 ("spi/pxa2xx: convert to the common clk framework")
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The BCM2835 AUX SPI has a shared interrupt line (with AUX UART).
Downstream fixes this with an AUX irqchip to demux the IRQ sources and a
DT change which breaks compatibility with older kernels. The AUX irqchip
was already rejected for upstream[1] and the DT change would break
working systems if the DTB is updated to a newer one. The latter issue
was brought to my attention by Alex Graf.

The root cause however is a bug in the shared handler. Shared handlers
must check that interrupts are actually enabled before servicing the
interrupt. Add a check that the TXEMPTY or IDLE interrupts are enabled.

[1] https://patchwork.kernel.org/patch/9781221/

Cc: Alexander Graf <agraf@suse.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-spi@vger.kernel.org
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Mark Brown <broonie@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management.

Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

We currently are calling mcspi suspend and resume without considering
that mcspi might provide resources for other device driver such as
regulators. This means resume can fail and will produce -EACCES if
errors if anything calls mcspi functions between device_prepare()
and device_complete().

To fix the issue, let's do the following changes:

1. Let's add checking for return values for pm_runtime_get calls,
   and call pm_runtime_put_noidle() on errors. Things still fail
   after this change, but at least we see something is wrong as
   we now see -EACCES errors on resume.

2. Let's use noirq level for suspend and resume as other drivers
   can still call SPI related functions on suspend and resume. This
   still won't fix the -EACCES issue, but gets us to something a bit
   saner.

3. Finally, let's modify suspend and resume to call to make sure
   the device is idled properly on suspend. We have device_prepare()
   call pm_runtime_get_noresume() that won't get released until in
   device_complete() when it calls pm_runtime_put(). So if SPI is
   still active on entering suspend, it will never get idled unless
   we add calls to pm_runtime_force_suspend() and resume. This also
   fixes the -EACCES errors on resume together with changes 1 and 2
   above.

And since we're already rewriting suspend resume functions, let's
arrange the order of suspend and resume functions to be like they
usually are with suspend first.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

We can have the SoC enter off mode also during idle, not just
during suspend. Currently we are handling the CS restore properly
for unused CS only for resume and not for runtime resume.

Let's just move all the context related restore to runtime_resume().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

If devm_spi_register_master() fails in meson_spicc_probe(),
spicc->core is left undisabled. The patch fixes that.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Always confirm the BSPI_MAST_N_BOOT_CTRL bit when enabling
or disabling BSPI transfers.

Fixes: 4e3b2d23 ("spi: bcm-qspi: Add BSPI spi-nor flash controller driver")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

Added fix for probing of spi-nor device non-zero chip selects. Set
MSPI_CDRAM_PCS (peripheral chip select) with spi master for MSPI
controller and not for MSPI/BSPI spi-nor master controller. Ensure
setting of cs bit in chip select register on chip select change.

Fixes: fa236a7e ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

Replace the manual validity checks for the GPIO with the
gpio_is_valid().
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Right now, no checks are done on the presence of a ->transfer[_xxx]()
method, which can lead to a NULL pointer dereference when someone
starts sending something on the bus.

Do the check at registration time and refuse to add the controller if
all ->transfer[_xxx]() pointers are NULL.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Enable the clock prior to calling clk_get_rate(), because clk_get_rate()
should only be called if the clock is enabled.

Additionally, prepare/enable the pll_clk before calling clk_get_rate()
for the same reason.

Found by Linux Driver Verification project (linuxtesting.org).

Fixes: 142168eb ("spi: bcm63xx-hsspi: add bcm63xx HSSPI driver")
Signed-off-by: Stefan Potyra <Stefan.Potyra@elektrobit.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The Exynos5440 is not actively developed, there are no development
boards available and probably there are no real products with it.
Remove wide-tree support for Exynos5440.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Currently the 32-bit device address only is supported for DMA. However,
starting from Intel Sunrisepoint PCH the DMA address of the device FIFO
can be 64-bit.

Change the respective variable to be compatible with DMA engine
expectations, i.e. to phys_addr_t.

Fixes: 34cadd9c ("spi: pxa2xx: Add support for Intel Sunrisepoint")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

This is needed by the spi-mem logic to force all messages that have been
queued before a memory operation to be sent before we start the memory
operation. We do that in order to guarantee that spi-mem operations do
not preempt regular SPI transfers.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi_{map,unmap}_buf() are needed by the spi-mem logic that is about to
be introduced to prepare data buffer for DMA operations.

Remove the static specifier on these functions and add their prototypes
to drivers/spi/internals.h. We do not export the symbols here because
both SPI_MEM and SPI can't be enabled as modules and we'd like to
prevent controller/device drivers from using these functions.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Currently the 32-bit device address only is supported for DMA. However,
starting from Intel Sunrisepoint PCH the DMA address of the device FIFO
can be 64-bit.

Change the respective variable to be compatible with DMA engine
expectations, i.e. to phys_addr_t.

Fixes: 34cadd9c ("spi: pxa2xx: Add support for Intel Sunrisepoint")
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Some variants of the SPI controller have no DMA support, in such case
SPI transfers longer than the FIFO length are not currently properly
handled by the driver. Fix it by doing multiple transfers in the
s3c64xx_spi_transfer_one() function if the SPI transfer length exceeds
the FIFO size.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

More references to fifo_len are added in subsequent patch.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fixes: d5898e19 ("spi: pxa2xx: Use core message processing loop")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>