Since commit aef9a7bd ("serial/uart/8250: Add tunable RX interrupt
trigger I/F of FIFO buffers"), the port's default FCR value isn't used
in serial8250_do_set_termios anymore, but copied over once in
serial8250_config_port and then modified as needed.

Unfortunately, serial8250_config_port will never be called if the port
is shared between kernel and userspace, and the port's flag doesn't have
UPF_BOOT_AUTOCONF, which would trigger a serial8250_config_port as well.

This causes garbled output from userspace:

[    5.220000] random: procd urandom read with 49 bits of entropy available
ers
   [kee

Fix this by forcing it to be configured on boot, resulting in the
expected output:

[    5.250000] random: procd urandom read with 50 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level

Fixes: aef9a7bd ("serial/uart/8250: Add tunable RX interrupt trigger I/F of FIFO buffers")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Nicolas Schichan <nschichan@freebox.fr>
Cc: linux-mips@linux-mips.org
Cc: linux-serial@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/17544/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Pull MIPS fixes from Ralf Baechle:
 "Another round of MIPS fixes for 4.15.

   - Maciej Rozycki found another series of FP issues which requires a
     seven part series to restructure and fix.

   - James fixes a warning about .set mt which gas doesn't like when
     building for R1 processors"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Validate PR_SET_FP_MODE prctl(2) requests against the ABI of the task
  MIPS: Disallow outsized PTRACE_SETREGSET NT_PRFPREG regset accesses
  MIPS: Also verify sizeof `elf_fpreg_t' with PTRACE_SETREGSET
  MIPS: Fix an FCSR access API regression with NT_PRFPREG and MSA
  MIPS: Consistently handle buffer counter with PTRACE_SETREGSET
  MIPS: Guard against any partial write attempt with PTRACE_SETREGSET
  MIPS: Factor out NT_PRFPREG regset access helpers
  MIPS: CPS: Fix r1 .set mt assembler warning

Pull block fixes from Jens Axboe:
 "A set of fixes that should go into this release. This contains:

   - An NVMe pull request from Christoph, with a few critical fixes for
     NVMe.

   - A block drain queue fix from Ming.

   - The concurrent lo_open/release fix for loop"

* 'for-linus' of git://git.kernel.dk/linux-block:
  loop: fix concurrent lo_open/lo_release
  block: drain queue before waiting for q_usage_counter becoming zero
  nvme-fcloop: avoid possible uninitialized variable warning
  nvme-mpath: fix last path removal during traffic
  nvme-rdma: fix concurrent reset and reconnect
  nvme: fix sector units when going between formats
  nvme-pci: move use_sgl initialization to nvme_init_iod()

Pull networking fixes from David Miller:

 1) Frag and UDP handling fixes in i40e driver, from Amritha Nambiar and
    Alexander Duyck.

 2) Undo unintentional UAPI change in netfilter conntrack, from Florian
    Westphal.

 3) Revert a change to how error codes are returned from
    dev_get_valid_name(), it broke some apps.

 4) Cannot cache routes for ipv6 tunnels in the tunnel is ipv4/ipv6
    dual-stack. From Eli Cooper.

 5) Fix missed PMTU updates in geneve, from Xin Long.

 6) Cure double free in macvlan, from Gao Feng.

 7) Fix heap out-of-bounds write in rds_message_alloc_sgs(), from
    Mohamed Ghannam.

 8) FEC bug fixes from FUgang Duan (mis-accounting of dev_id, missed
    deferral of probe when the regulator is not ready yet).

 9) Missing DMA mapping error checks in 3c59x, from Neil Horman.

10) Turn off Broadcom tags for some b53 switches, from Florian Fainelli.

11) Fix OOPS when get_target_net() is passed an SKB whose NETLINK_CB()
    isn't initialized. From Andrei Vagin.

12) Fix crashes in fib6_add(), from Wei Wang.

13) PMTU bug fixes in SCTP from Marcelo Ricardo Leitner.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (56 commits)
  sh_eth: fix TXALCR1 offsets
  mdio-sun4i: Fix a memory leak
  phylink: mark expected switch fall-throughs in phylink_mii_ioctl
  sctp: fix the handling of ICMP Frag Needed for too small MTUs
  sctp: do not retransmit upon FragNeeded if PMTU discovery is disabled
  xen-netfront: enable device after manual module load
  bnxt_en: Fix the 'Invalid VF' id check in bnxt_vf_ndo_prep routine.
  bnxt_en: Fix population of flow_type in bnxt_hwrm_cfa_flow_alloc()
  sh_eth: fix SH7757 GEther initialization
  net: fec: free/restore resource in related probe error pathes
  uapi/if_ether.h: prevent redefinition of struct ethhdr
  ipv6: fix general protection fault in fib6_add()
  RDS: null pointer dereference in rds_atomic_free_op
  sh_eth: fix TSU resource handling
  net: stmmac: enable EEE in MII, GMII or RGMII only
  rtnetlink: give a user socket to get_target_net()
  MAINTAINERS: Update my email address.
  can: ems_usb: improve error reporting for error warning and error passive
  can: flex_can: Correct the checking for frame length in flexcan_start_xmit()
  can: gs_usb: fix return value of the "set_bittiming" callback
  ...

Pull rdma fixes from Doug Ledford:

 - One line fix to mlx4 error flow (same as mlx5 fix in last pull
   request, just in the mlx4 driver)

 - Fix a race condition in the IPoIB driver. This patch is larger than
   just a one line fix, but resolves a race condition in a fairly
   straight forward manner

 - Fix a locking issue in the RDMA netlink code. This patch is also
   larger than I would like for a late -rc. It has, however, had a week
   to bake in the rdma tree prior to this pull request

 - One line fix to fix granting remote machine access to memory that
   they don't need and shouldn't have

 - One line fix to correct the fact that our sgid/dgid pair is swapped
   from what you would expect when receiving an incoming connection
   request

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  IB/srpt: Fix ACL lookup during login
  IB/srpt: Disable RDMA access by the initiator
  RDMA/netlink: Fix locking around __ib_get_device_by_index
  IB/ipoib: Fix race condition in neigh creation
  IB/mlx4: Fix mlx4_ib_alloc_mr error flow

Pull x86 platform driver fix from Darren Hart:
 "Address a wmi initcall ordering race resulting in a difficult to
  reproduce boot failure"

* tag 'platform-drivers-x86-v4.15-4' of git://git.infradead.org/linux-platform-drivers-x86:
  platform/x86: wmi: Call acpi_wmi_init() later

The  TXALCR1 offsets are incorrect in the register offset tables, most
probably due to copy&paste error.  Luckily, the driver never uses this
register. :-)

Fixes: 4a55530f ("net: sh_eth: modify the definitions of register")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the probing of the regulator is deferred, the memory allocated by
'mdiobus_alloc_size()' will be leaking.
It should be freed before the next call to 'sun4i_mdio_probe()' which will
reallocate it.

Fixes: 4bdcb1dd ("net: Add MDIO bus driver for the Allwinner EMAC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Addresses-Coverity-ID: 1463447 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marcelo Ricardo Leitner says:

====================
SCTP PMTU discovery fixes

This patchset fixes 2 issues with PMTU discovery that can lead to flood
of retransmissions.
The first patch fixes the issue for when PMTUD is disabled by the
application, while the second fixes it for when its enabled.

Please consider these to stable.
====================
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot reported a hang involving SCTP, on which it kept flooding dmesg
with the message:
[  246.742374] sctp: sctp_transport_update_pmtu: Reported pmtu 508 too
low, using default minimum of 512

That happened because whenever SCTP hits an ICMP Frag Needed, it tries
to adjust to the new MTU and triggers an immediate retransmission. But
it didn't consider the fact that MTUs smaller than the SCTP minimum MTU
allowed (512) would not cause the PMTU to change, and issued the
retransmission anyway (thus leading to another ICMP Frag Needed, and so
on).

As IPv4 (ip_rt_min_pmtu=556) and IPv6 (IPV6_MIN_MTU=1280) minimum MTU
are higher than that, sctp_transport_update_pmtu() is changed to
re-fetch the PMTU that got set after our request, and with that, detect
if there was an actual change or not.

The fix, thus, skips the immediate retransmission if the received ICMP
resulted in no change, in the hope that SCTP will select another path.

Note: The value being used for the minimum MTU (512,
SCTP_DEFAULT_MINSEGMENT) is not right and instead it should be (576,
SCTP_MIN_PMTU), but such change belongs to another patch.

Changes from v1:
- do not disable PMTU discovery, in the light of commit
06ad3919 ("[SCTP] Don't disable PMTU discovery when mtu is small")
and as suggested by Xin Long.
- changed the way to break the rtx loop by detecting if the icmp
  resulted in a change or not
Changes from v2:
none

See-also: https://lkml.org/lkml/2017/12/22/811Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, if PMTU discovery is disabled on a given transport, but the
configured value is higher than the actual PMTU, it is likely that we
will get some icmp Frag Needed. The issue is, if PMTU discovery is
disabled, we won't update the information and will issue a
retransmission immediately, which may very well trigger another ICMP,
and another retransmission, leading to a loop.

The fix is to simply not trigger immediate retransmissions if PMTU
discovery is disabled on the given transport.

Changes from v2:
- updated stale comment, noticed by Xin Long
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When loading the module after unloading it, the network interface would
not be enabled and thus wouldn't have a backend counterpart and unable
to be used by the guest.

The guest would face errors like:

  [root@guest ~]# ethtool -i eth0
  Cannot get driver information: No such device

  [root@guest ~]# ifconfig eth0
  eth0: error fetching interface information: Device not found

This patch initializes the state of the netfront device whenever it is
loaded manually, this state would communicate the netback to create its
device and establish the connection between them.
Signed-off-by: Eduardo Otubo <otubo@redhat.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: 2 small bug fixes.

The first one fixes the TC Flower flow parameter passed to firmware.  The
2nd one fixes the VF index range checking for iproute2 SRIOV related commands.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In bnxt_vf_ndo_prep (which is called by bnxt_get_vf_config ndo), there is a
check for "Invalid VF id". Currently, the check is done against max_vfs.
However, the user doesn't always create max_vfs. So, the check should be
against the created number of VFs. The number of bnxt_vf_info structures
that are allocated in bnxt_alloc_vf_resources routine is the "number of
requested VFs". So, if an "invalid VF id" falls between the requested
number of VFs and the max_vfs, the driver will be dereferencing an invalid
pointer.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Venkat Devvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

flow_type in HWRM_FLOW_ALLOC is not being populated correctly due to
incorrect passing of pointer and size of l3_mask argument of is_wildcard().
Fixed this.

Fixes: db1d36a2 ("bnxt_en: add TC flower offload flow_alloc/free FW cmds")
Signed-off-by: Sunil Challa <sunilkumar.challa@broadcom.com>
Reviewed-by: Sathya Perla <sathya.perla@broadcom.com>
Reviewed-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull cgroup fixes from Tejun Heo:
 "This contains fixes for the following two non-trivial issues:

   - The task iterator got broken while adding thread mode support for
     v4.14. It was less visible because it only triggers when both
     cgroup1 and cgroup2 hierarchies are in use. The recent versions of
     systemd uses cgroup2 for process management even when cgroup1 is
     used for resource control exposing this issue.

   - cpuset CPU hotplug path could deadlock when racing against exits.

  There also are two patches to replace unlimited strcpy() usages with
  strlcpy()"

* 'for-4.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: fix css_task_iter crash on CSS_TASK_ITER_PROC
  cgroup: Fix deadlock in cpu hotplug path
  cgroup: use strlcpy() instead of strscpy() to avoid spurious warning
  cgroup: avoid copying strings longer than the buffers

Calling acpi_wmi_init() at the subsys_initcall() level causes ordering
issues to appear on some systems and they are difficult to reproduce,
because there is no guaranteed ordering between subsys_initcall()
calls, so they may occur in different orders on different systems.

In particular, commit 86d9f485 (mm/slab: fix kmemcg cache
creation delayed issue) exposed one of these issues where genl_init()
and acpi_wmi_init() are both called at the same initcall level, but
the former must run before the latter so as to avoid a NULL pointer
dereference.

For this reason, move the acpi_wmi_init() invocation to the
initcall_sync level which should still be early enough for things
to work correctly in the WMI land.

Link: https://marc.info/?t=151274596700002&r=1&w=2Reported-by: Jonathan McDowell <noodles@earth.li>
Reported-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Tested-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>

Pull parisc fixes from Helge Deller:

 - Many small fixes to show the real physical addresses of devices
   instead of hashed addresses.

 - One important fix to unbreak 32-bit SMP support: We forgot to 16-byte
   align the spinlocks in the assembler code.

 - Qemu support: The host will get a chance to sleep when the parisc
   guest is idle. We use the same mechanism as the power architecture by
   overlaying the "or %r10,%r10,%r10" instruction which is simply a nop
   on real hardware.

* 'parisc-4.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: qemu idle sleep support
  parisc: Fix alignment of pa_tlb_lock in assembly on 32-bit SMP kernel
  parisc: Show unhashed EISA EEPROM address
  parisc: Show unhashed HPA of Dino chip
  parisc: Show initial kernel memory layout unhashed
  parisc: Show unhashed hardware inventory

Merge tag 'apparmor-pr-2018-01-07' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor

Pull apparmor fix from John Johansen:
 "This fixes a regression when the kernel feature set is reported as
  supporting mount and policy is pinned to a feature set that does not
  support mount mediation"

* tag 'apparmor-pr-2018-01-07' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor:
  apparmor: fix regression in mount mediation when feature set is pinned

Merge tag 'led_fixes_for_4.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds

Pull LED fix from Jacek Anaszewski:
 "The commit 2b83ff96 for 4.15-rc6, which was fixing LED brightness
  setting after clearing delay_off broke the behavior on any alteration
  of delay_on{off} properties, due to use of a LED core helper that does
  too much for this particular case"

* tag 'led_fixes_for_4.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
  leds: core: Fix regression caused by commit 2b83ff96

Pull MTD bugfix from Richard Weinberger:
 "A single fix for the pxa3xx NAND driver"

* tag 'for-linus-20180107' of git://git.infradead.org/linux-mtd:
  mtd: nand: pxa3xx: Fix READOOB implementation

Commit 2b83ff96 ("led: core: Fix brightness setting when setting delay_off=0")
replaced del_timer_sync(&led_cdev->blink_timer) with led_stop_software_blink()
in led_blink_set(), which additionally clears LED_BLINK_SW flag as well as
zeroes blink_delay_on and blink_delay_off properties of the struct led_classdev.

Cleansing of the latter ones wasn't required to fix the original issue but
wasn't considered harmful. It nonetheless turned out to be so in case when
pointer to one or both props is passed to led_blink_set() like in the
ledtrig-timer.c. In such cases zeroes are passed later in delay_on and/or
delay_off arguments to led_blink_setup(), which results either in stopping
the software blinking or setting blinking frequency always to 1Hz.

Avoid using led_stop_software_blink() and add a single call required
to clear LED_BLINK_SW flag, which was the only needed modification to
fix the original issue.

Fixes 2b83ff96 ("led: core: Fix brightness setting when setting delay_off=0")
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>

Pull vfs fixes from Al Viro:

 - untangle sys_close() abuses in xt_bpf

 - deal with register_shrinker() failures in sget()

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fix "netfilter: xt_bpf: Fix XT_BPF_MODE_FD_PINNED mode of 'xt_bpf_info_v1'"
  sget(): handle failures of register_shrinker()
  mm,vmscan: Make unregister_shrinker() no-op if register_shrinker() failed.

Pull KVM fixes from Radim Krčmář:
 "s390:
   - Two fixes for potential bitmap overruns in the cmma migration code

  x86:
   - Clear guest provided GPRs to defeat the Project Zero PoC for CVE
     2017-5715"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  kvm: vmx: Scrub hardware GPRs at VM-exit
  KVM: s390: prevent buffer overrun on memory hotplug during migration
  KVM: s390: fix cmma migration for multiple memory slots

In the current driver, OOB bytes are accessed in raw mode, and when a
page access is done with NDCR_SPARE_EN set and NDCR_ECC_EN cleared, the
driver must read the whole spare area (64 bytes in case of a 2k page,
16 bytes for a 512 page). The driver was only reading the free OOB
bytes, which was leaving some unread data in the FIFO and was somehow
leading to a timeout.

We could patch the driver to read ->spare_size + ->ecc_size instead of
just ->spare_size when READOOB is requested, but we'd better make
in-band and OOB accesses consistent.
Since the driver is always accessing in-band data in non-raw mode (with
the ECC engine enabled), we should also access OOB data in this mode.
That's particularly useful when using the BCH engine because in this
mode the free OOB bytes are also ECC protected.

Fixes: 43bcfd2b ("mtd: nand: pxa3xx: Add driver-specific ECC BCH support")
Cc: stable@vger.kernel.org
Reported-by: Sean Nyekjær <sean.nyekjaer@prevas.dk>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Richard Weinberger <richard@nod.at>

Pull powerpc fix from Michael Ellerman:
 "Just one fix to correctly return SEGV_ACCERR when we take a SEGV on a
  mapped region. The bug was introduced in the refactoring of the page
  fault handler we did in the previous release.

  Thanks to John Sperbeck"

* tag 'powerpc-4.15-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/mm: Fix SEGV on mapped region to return SEGV_ACCERR

范龙飞 reports that KASAN can report a use-after-free in __lock_acquire.
The reason is due to insufficient serialization in lo_release(), which
will continue to use the loop device even after it has decremented the
lo_refcnt to zero.

In the meantime, another process can come in, open the loop device
again as it is being shut down. Confusion ensues.
Reported-by: 范龙飞 <long7573@126.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

KVM: s390: fixes for cmma migration

Two fixes for potential bitmap overruns in the cmma migration
code.

Add qemu idle sleep support when running under qemu with SeaBIOS PDC
firmware.

Like the power architecture we use the "or" assembler instructions,
which translate to nops on real hardware, to indicate that qemu shall
idle sleep.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: Richard Henderson <rth@twiddle.net>
CC: stable@vger.kernel.org # v4.9+

Pull input fixes from Dmitry Torokhov:
 "Just a few driver fixups, nothing exciting"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: xen-kbdfront - do not advertise multi-touch pressure support
  Input: hideep - fix compile error due to missing include file
  Input: elants_i2c - do not clobber interrupt trigger on x86
  Input: joystick/analog - riscv has get_cycles()
  Input: elantech - add new icbody type 15
  Input: ims-pcu - fix typo in the error message

Pull IOMMU fixes from Alex Williamson:
 "Fixes via Will Deacon for arm-smmu-v3.

   - Fix duplicate Stream ID handling in arm-smmu-v3

   - Fix arm-smmu-v3 page table ops double free"

* tag 'iommu-v4.15-rc7' of git://github.com/awilliam/linux-vfio:
  iommu/arm-smmu-v3: Cope with duplicated Stream IDs
  iommu/arm-smmu-v3: Don't free page table ops twice

Pull ARC fixes from Vineet Gupta:

 - platform updates for setting up clock correctly

 - fixes to accomodate newer gcc (__builtin_trap, removed inline asm
   modifier)

 - other fixes

* tag 'arc-4.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: handle gcc generated __builtin_trap for older compiler
  ARC: handle gcc generated __builtin_trap()
  ARC: uaccess: dont use "l" gcc inline asm constraint modifier
  ARC: [plat-axs103] refactor the quad core DT quirk code
  ARC: [plat-axs103]: Set initial core pll output frequency
  ARC: [plat-hsdk]: Get rid of core pll frequency set in platform code
  ARC: [plat-hsdk]: Set initial core pll output frequency
  ARC: [plat-hsdk] Switch DisplayLink driver from fbdev to DRM
  arc: do not use __print_symbol()
  ARC: Fix detection of dual-issue enabled

When the mount code was refactored for Labels it was not correctly
updated to check whether policy supported mediation of the mount
class.  This causes a regression when the kernel feature set is
reported as supporting mount and policy is pinned to a feature set
that does not support mount mediation.

BugLink: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=882697#41
Fixes: 2ea3ffb7 ("apparmor: add mount mediation")
Reported-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John Johansen <john.johansen@canonical.com>

Pull btrfs fixes from David Sterba:
 "We have two more fixes for 4.15, both aimed for stable.

  The leak fix is obvious, the second patch fixes a bug revealed by the
  refcount API, when it behaves differently than previous atomic_t and
  reports refs going from 0 to 1 in one case"

* tag 'for-4.15-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: fix refcount_t usage when deleting btrfs_delayed_nodes
  btrfs: Fix flush bio leak

Pull XFS fixes from Darrick Wong:
 "I have just a few fixes for bugs and resource cleanup problems this
  week:

   - Fix resource cleanup of failed quota initialization

   - Fix integer overflow problems wrt s_maxbytes"

* tag 'xfs-4.15-fixes-10' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: fix s_maxbytes overflow problems
  xfs: quota: check result of register_shrinker()
  xfs: quota: fix missed destroy of qi_tree_lock

Pull MFD fix from Lee Jones:
 "Late bugfix to plug a leak in rtsx_pcr"

* tag 'mfd-fixes-4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
  mfd: rtsx: Release IRQ during shutdown

Pull  more x86 pti fixes from Thomas Gleixner:
 "Another small stash of fixes for fallout from the PTI work:

   - Fix the modules vs. KASAN breakage which was caused by making
     MODULES_END depend of the fixmap size. That was done when the cpu
     entry area moved into the fixmap, but now that we have a separate
     map space for that this is causing more issues than it solves.

   - Use the proper cache flush methods for the debugstore buffers as
     they are mapped/unmapped during runtime and not statically mapped
     at boot time like the rest of the cpu entry area.

   - Make the map layout of the cpu_entry_area consistent for 4 and 5
     level paging and fix the KASLR vaddr_end wreckage.

   - Use PER_CPU_EXPORT for per cpu variable and while at it unbreak
     nvidia gfx drivers by dropping the GPL export. The subject line of
     the commit tells it the other way around, but I noticed that too
     late.

   - Fix the ASM alternative macros so they can be used in the middle of
     an inline asm block.

   - Rename the BUG_CPU_INSECURE flag to BUG_CPU_MELTDOWN so the attack
     vector is properly identified. The Spectre mitigations will come
     with their own bug bits later"

* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/pti: Rename BUG_CPU_INSECURE to BUG_CPU_MELTDOWN
  x86/alternatives: Add missing '\n' at end of ALTERNATIVE inline asm
  x86/tlb: Drop the _GPL from the cpu_tlbstate export
  x86/events/intel/ds: Use the proper cache flush method for mapping ds buffers
  x86/kaslr: Fix the vaddr_end mess
  x86/mm: Map cpu_entry_area at the same place on 4/5 level
  x86/mm: Set MODULES_END to 0xffffffffff000000

Pull EFI updates from Thomas Gleixner:

 - A fix for a add_efi_memmap parameter regression which ensures that
   the parameter is parsed before it is used.

 - Reinstate the virtual capsule mapping as the cached copy turned out
   to break Quark and other things

 - Remove Matt Fleming as EFI co-maintainer. He stepped back a few days
   ago. Thanks Matt for all your great work!

* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  MAINTAINERS: Remove Matt Fleming as EFI co-maintainer
  efi/capsule-loader: Reinstate virtual capsule mapping
  x86/efi: Fix kernel param add_efi_memmap regression