These bits are used in op_tx to determine if a packet should be dropped.
As such we should use the spin lock to sync the state.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

With PSM handled in FW, the checks in wl1271_elp_work() are always true.
Thus during active traffic we constantly enter and exit ELP (many times
per second). As each ELP exit takes ~10ms, this can have an adverse
effect on throughput and interactivity.
Set the ELP timeout to the dyn-ps timeout. This period is longer and
avoids the above problem. It also makes sense to stay out of ELP while
we are awake on the network, to minimize delays in Tx/Rx. The same thing
was done by the mac80211 dynamic-ps mechanism before the FW DPS changes.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Bring MCU operations during device initialization to sync
with legacy driver.

This should fix following error:
phy0 -> rt2800pci_mcu_status: Error - MCU request failed,
no response from hardware
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add documentation on MCU communication, some of known commands and
their arguments. Supplement command ids.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/iwlwifi/iwl-core.c included 'iwl-agn.h' twice,
remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The second line of a printk statement must line up to the opening bracket.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

That's a lot longer than open-coding it and
doesn't really add value, so just remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The comment for sta_info_flush() states
"Returns the number of removed STA entries"
but that isn't actually true. Consequently,
the warning when a station is still around
on interface removal can never trigger and
this delayed finding the timer issue the
previous patch fixed. Fix the return value
here to make that warning useful again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When removing an interface while it is in the
process of authenticating or associating, we
leak the auth_data or assoc_data, and leave
the timer pending. The timer then crashes the
system when it fires as its data is gone.

Fix this by explicitly deleting all the data
when the interface is removed. This uncovered
another bug -- this problem should have been
detected by the sta_info_flush() warning but
that function doesn't ever return non-zero,
I'll fix that in a separate patch.
Reported-by: Hieu Nguyen <hieux.c.nguyen@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Also don't use so generic BRCMF_USB_FW_NAME as we may need different
firmwares in the future.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There were two dereferencing before checking for NULL static checker
complaints in this new file.  The list cursor is never NULL so that
check can be removed.  I moved the other dereference after the check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use IW_HANDLER macro in ipw2100.c to declare wireless handlers.

Note: ipw2200.c already uses it.
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use interface data from sta instead of invalid pointer
to list head in calls to drv_sta_state.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Cleanup whitespace, fix indentation and coding style.
Also remove debug messages that were flooding the log.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes indentation and the general coding style
in ar9003_mci.c. Also, minimize the amount of debug log
output generated by MCI.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

They are not needed since MCI will be enabled only for
AR9462 v2.0
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* Use a separate function to enable/disable
  OneStepLookAhead.

* Remove unnecessary hardware SREV checks.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ATH9K_BTCOEX_SUPPORT is now used by both ath9k and ath9k_htc
to enable BT coexistence. Fix Kbuild to allow this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With the ability to remove BTCOEX support at compile time,
these checks are no longer needed.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since BTCOEX code can be compiled out cleanly now,
remove these checks.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc can also make use of CONFIG_ATH9K_BTCOEX_SUPPORT
to be compiled without BTCOEX support.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Make use of CONFIG_ATH9K_BTCOEX_SUPPORT in ath9k_hw
to provide a clean way of compilation without BTCOEX
support.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch converts a few functions to static variants
and removes extraneous declarations.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch moves all the MCI-specific declarations that have been
dumped unceremoniously in hw.h to ar9003_mci.h
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch moves all the MCI-specific code in the main reset
function to helper functions.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Setting up the required scheme can be done as part of the
BTCOEX initialization path and it doesn't belong in
ath9k_hw_fill_cap_info() anyway.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch uses CONFIG_ATH9K_BTCOEX_SUPPORT to conditionally
compile btcoex-related code in the driver core.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch simplifies the buffer allocation functions
for MCI and removes unneeded memset calls. Also, a couple
of unused variables are removed and a memory leak in DMA
allocation is fixed.

[ 1263.788267] WARNING: at /home/sujith/dev/wireless-testing/lib/dma-debug.c:875 check_unmap+0x173/0x7e0()
[ 1263.788273] ath9k 0000:06:00.0: DMA-API: device driver frees DMA memory with different size
               [device address=0x0000000071908000] [map size=512 bytes] [unmap size=256 bytes]
[ 1263.788345] Pid: 774, comm: rmmod Tainted: G        W  O 3.3.0-rc3-wl #18
[ 1263.788348] Call Trace:
[ 1263.788355]  [<ffffffff8105110f>] warn_slowpath_common+0x7f/0xc0
[ 1263.788359]  [<ffffffff81051206>] warn_slowpath_fmt+0x46/0x50
[ 1263.788363]  [<ffffffff8125a713>] check_unmap+0x173/0x7e0
[ 1263.788368]  [<ffffffff8123fc22>] ? prio_tree_left+0x32/0xc0
[ 1263.788373]  [<ffffffff8125aded>] debug_dma_free_coherent+0x6d/0x80
[ 1263.788381]  [<ffffffffa0701c3c>] ath_mci_cleanup+0x7c/0x110 [ath9k]
[ 1263.788387]  [<ffffffffa06f4033>] ath9k_deinit_softc+0x113/0x120 [ath9k]
[ 1263.788392]  [<ffffffffa06f55cc>] ath9k_deinit_device+0x5c/0x70 [ath9k]
[ 1263.788397]  [<ffffffffa0704934>] ath_pci_remove+0x54/0xa0 [ath9k]
[ 1263.788401]  [<ffffffff81267d06>] pci_device_remove+0x46/0x110
[ 1263.788406]  [<ffffffff813102bc>] __device_release_driver+0x7c/0xe0
[ 1263.788410]  [<ffffffff81310a00>] driver_detach+0xd0/0xe0
[ 1263.788414]  [<ffffffff81310118>] bus_remove_driver+0x88/0xe0
[ 1263.788418]  [<ffffffff813111c2>] driver_unregister+0x62/0xa0
[ 1263.788421]  [<ffffffff812680c4>] pci_unregister_driver+0x44/0xc0
[ 1263.788427]  [<ffffffffa0705015>] ath_pci_exit+0x15/0x20 [ath9k]
[ 1263.788432]  [<ffffffffa070a92d>] ath9k_exit+0x15/0x31 [ath9k]
[ 1263.788436]  [<ffffffff810b971c>] sys_delete_module+0x18c/0x270
[ 1263.788441]  [<ffffffff81436edd>] ? retint_swapgs+0x13/0x1b
[ 1263.788446]  [<ffffffff812483be>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[ 1263.788450]  [<ffffffff814378e9>] system_call_fastpath+0x16/0x1b
[ 1263.788453] ---[ end trace 3ab4d030ffde40d4 ]---
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

v1.0 chips are not available in the market.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Eliad reports that if a scan finishes in the
middle of processing associated (however it
happens), the interface can go idle. This is
because we set assoc_data to NULL before we
set associated. Change the order so any idle
check will find either one of them.

Doing this requires duplicating the TX sync
processing, but I already have a patch to
delete that completely and will submit that
as soon as my driver changes to no longer
require it are submitted.
Reported-by: Eliad Peller <eliad@wizery.com>
Tested-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>