When the new IEs are generated, the multiple BSSID elements
are not saved. Save aside properties that are needed later
for PS.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This will enable reuse by mac80211.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Parsing and exposing nontransmitted APs is problematic
when underlying HW doesn't support it. Do it only if
driver indicated support. Allow HE restriction as well,
since the HE spec defined the exact manner that Multiple
BSSID set should behave. APs that not support the HE
spec will have less predictable Multiple BSSID set
support/behavior
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Previously the transmitted BSS and the non-trasmitted BSS list were
defined in struct cfg80211_internal_bss. Move them to struct cfg80211_bss
since mac80211 needs this info.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When holding data of the non-transmitting BSS, we need to keep the
transmitting BSS data on. Otherwise it will be released, and release
the non-transmitting BSS with it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Use the new for_each_element() helper here, we cannot use
for_each_subelement() since we have a fixed 1 byte before
the subelements start.

While at it, also fix le16_to_cpup() to be get_unaligned_le16()
since we don't know anything about alignment.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This extends cfg80211 BSS table processing to be able to parse Multiple
BSSID element from Beacon and Probe Response frames and to update the
BSS profiles in internal database for non-transmitted BSSs.
Signed-off-by: Peng Xu <pxu@codeaurora.org>
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This will allow iterating over multiple BSSs inside
cfg80211_bss, in case of multiple BSSID.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In multiple BSSID, we have nested IEs inside the multiple
BSSID IE, that override the external ones for that specific
BSS. As preparation for supporting that, pass 2 BSSIDs to the
parse function, the transmitter, and the selected BSSID, so
it can know which IEs to choose. If the selected BSSID is
NULL, the outer ones will be applied.

Change ieee80211_bss_info_update to parse elements itself,
instead of receiving them parsed, so we have the relevant
bss entry in hand.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This makes for much simpler code, simply walk through all
the elements and check that the last one found ends with
the end of the data. This works because if any element is
malformed the walk is aborted, we end up with a mismatch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

We currently have a number of helpers to find elements that just
return a u8 *, change those to return a struct element and add
inlines to deal with the u8 * compatibility.

Note that the match behaviour is changed to start the natch at
the data, so conversion from _ie_match to _elem_match need to
be done carefully.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Instead of open-coding the element walk, use the new macro.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Rather than always iterating elements from frames with pure
u8 pointers, add a type "struct element" that encapsulates
the id/datalen/data format of them.

Then, add the element iteration macros
 * for_each_element
 * for_each_element_id
 * for_each_element_extid

which take, as their first 'argument', such a structure and
iterate through a given u8 array interpreting it as elements.

While at it and since we'll need it, also add
 * for_each_subelement
 * for_each_subelement_id
 * for_each_subelement_extid

which instead of taking data/length just take an outer element
and use its data/datalen.

Also add for_each_element_completed() to determine if any of
the loops above completed, i.e. it was able to parse all of
the elements successfully and no data remained.

Use for_each_element_id() in cfg80211_find_ie_match() as the
first user of this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This makes the age information for cfg80211 scan results more accurate
and fixes issues with wpa_supplicant dropping "old" scan results (e.g.,
"wlan0: Own scan request started a scan in 0.000456 seconds") that
looked like would have been received before a scan started due to the
inaccuracy of the default timing mechanism for calculating the BSS entry
age. This makes hwsim test cases significantly more robust to run.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Sven Auhagen reports that if he changes a SFP+ module for a SFP module
on the Macchiatobin Single Shot, the link does not come back up.  For
Sven, it is as easy as:

- Insert a SFP+ module connected, and use ping6 to verify link is up.
- Remove SFP+ module
- Insert SFP 1000base-X module use ping6 to verify link is up: Link
  up event did not trigger and the link is down

but that doesn't show the problem for me.  Locally, this has been
reproduced by:

- Boot with no modules.
- Insert SFP+ module, confirm link is up.
- Replace module with 25000base-X module.  Confirm link is up.
- Set remote end down, link is reported as dropped at both ends.
- Set remote end up, link is reported up at remote end, but not local
  end due to lack of link interrupt.

Fix this by setting up both GMAC and XLG interrupts for port 0, but
only unmasking the appropriate interrupt according to the current mode
set in the mac_config() method.  However, only do the mask/unmask
dance when we are really changing the link mode to avoid missing any
link interrupts.
Tested-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the phy_interface_mode_is_8023z() helper for detecting interface
modes that use 802.3z serial encoding.  This is equivalent to testing
for both 1000base-X and 2500base-X.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Moritz Fischer says:

====================
nixge: Fixed-link support

This series adds fixed-link support to nixge.

The first patch corrects the binding to correctly reflect
hardware that does not come with MDIO cores instantiated.

The second patch adds fixed link support to the driver.

The third patch updates the binding document with the now
optional (formerly required) phy-handle property and references
the fixed-link docs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Update device-tree binding with fixed-link support.

With fixed-link support the formerly required property 'phy-handle'
is now optional if 'fixed-link' child is present.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for fixed-link configurations to nixge driver.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make MDIO child optional and only instantiate the
MDIO bus if the child is actually present.

There are currently no (in-tree) users of this
binding; all (out-of-tree) users use overlays that
get shipped together with the FPGA images that contain
the IP.

This will significantly increase maintainabilty
of future revisions of this IP.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

All users of the fixed_phy_add() pass -1 as GPIO number
to the fixed phy driver, and all users of fixed_phy_register()
pass -1 as GPIO number as well, except for the device
tree MDIO bus.

Any new users should create a proper device and pass the
GPIO as a descriptor associated with the device so delete
the GPIO argument from the calls and drop the code looking
requesting a GPIO in fixed_phy_add().

In fixed phy_register(), investigate the "fixed-link"
node and pick the GPIO descriptor from "link-gpios" if
this property exists. Move the corresponding code out
of of_mdio.c as the fixed phy code anyways requires
OF to be in use.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the tab before '}' and keep the code style consistent.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sergei Shtylyov says:

====================
sh_eth: implement simple RX checksum offload

Here's a set of 7 patches against DaveM's 'net-next.git' repo. I'm implemeting
the simple RX checksum offload (like was done for the 'ravb' driver by Simon
Horman); it has been only tested on the R8A7740 and R8A77980 SoCs, the other
SoCs should just work (according to their manuals)...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The SH7763 SoC manual describes the Ether MAC's RX checksum offload
the same way as it's implemented in the EtherAVB MACs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The SH7734 SoC manual describes the Ether MAC's RX checksum offload
the same way as it's implemented in the EtherAVB MACs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The R-Car V3H (R8A77980) SoC manual describes the Ether MAC's RX checksum
offload the same way as it's implemented in the EtherAVB MAC...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The R-Mobile A1 (R8A7740) SoC manual describes the Ether MAC's RX checksum
offload the same way as it's implemented in the EtherAVB MAC...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

The RZ/A1H (R7S721000) SoC manual describes the Ether MAC's RX checksum
offload the same way as it's implemented in the EtherAVB MACs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for the RX checksum offload. This is enabled by default and
may be disabled and re-enabled using 'ethtool':

# ethtool -K eth0 rx off
# ethtool -K eth0 rx on

Some Ether MACs provide a simple checksumming scheme which appears to be
completely compatible with CHECKSUM_COMPLETE: sum of all packet data after
the L2 header is appended to packet data; this may be trivially read by
the driver and used to update the skb accordingly. The same checksumming
scheme is implemented in the EtherAVB MACs and now supported by the 'ravb'
driver.

In terms of performance, throughput is close to gigabit line rate with the
RX checksum offload both enabled and disabled.  The 'perf' output, however,
appears to indicate that significantly less time is spent in do_csum() --
this is as expected.

Test results with RX checksum offload enabled:

~/netperf-2.2pl4# perf record -a ./netperf -t TCP_MAERTS -H 192.168.2.4
TCP MAERTS TEST to 192.168.2.4
Recv   Send    Send
Socket Socket  Message  Elapsed
Size   Size    Size     Time     Throughput
bytes  bytes   bytes    secs.    10^6bits/sec

131072  16384  16384    10.01     933.93
[ perf record: Woken up 8 times to write data ]
[ perf record: Captured and wrote 1.955 MB perf.data (41940 samples) ]
~/netperf-2.2pl4# perf report
Samples: 41K of event 'cycles:ppp', Event count (approx.): 9915302763
Overhead  Command          Shared Object             Symbol
   9.44%  netperf          [kernel.kallsyms]         [k] __arch_copy_to_user
   7.75%  swapper          [kernel.kallsyms]         [k] _raw_spin_unlock_irq
   6.31%  swapper          [kernel.kallsyms]         [k] default_idle_call
   5.89%  swapper          [kernel.kallsyms]         [k] arch_cpu_idle
   4.37%  swapper          [kernel.kallsyms]         [k] tick_nohz_idle_exit
   4.02%  netperf          [kernel.kallsyms]         [k] _raw_spin_unlock_irq
   2.52%  netperf          [kernel.kallsyms]         [k] preempt_count_sub
   1.81%  netperf          [kernel.kallsyms]         [k] tcp_recvmsg
   1.80%  netperf          [kernel.kallsyms]         [k] _raw_spin_unlock_irqres
   1.78%  netperf          [kernel.kallsyms]         [k] preempt_count_add
   1.36%  netperf          [kernel.kallsyms]         [k] __tcp_transmit_skb
   1.20%  netperf          [kernel.kallsyms]         [k] __local_bh_enable_ip
   1.10%  netperf          [kernel.kallsyms]         [k] sh_eth_start_xmit

Test results with RX checksum offload disabled:

~/netperf-2.2pl4# perf record -a ./netperf -t TCP_MAERTS -H 192.168.2.4
TCP MAERTS TEST to 192.168.2.4
Recv   Send    Send
Socket Socket  Message  Elapsed
Size   Size    Size     Time     Throughput
bytes  bytes   bytes    secs.    10^6bits/sec
131072  16384  16384    10.01     932.04
[ perf record: Woken up 14 times to write data ]
[ perf record: Captured and wrote 3.642 MB perf.data (78817 samples) ]
~/netperf-2.2pl4# perf report
Samples: 78K of event 'cycles:ppp', Event count (approx.): 18091442796
Overhead  Command          Shared Object       Symbol
   7.00%  swapper          [kernel.kallsyms]   [k] do_csum
   3.94%  swapper          [kernel.kallsyms]   [k] sh_eth_poll
   3.83%  ksoftirqd/0      [kernel.kallsyms]   [k] do_csum
   3.23%  swapper          [kernel.kallsyms]   [k] _raw_spin_unlock_irq
   2.87%  netperf          [kernel.kallsyms]   [k] __arch_copy_to_user
   2.86%  swapper          [kernel.kallsyms]   [k] arch_cpu_idle
   2.13%  swapper          [kernel.kallsyms]   [k] default_idle_call
   2.12%  ksoftirqd/0      [kernel.kallsyms]   [k] sh_eth_poll
   2.02%  swapper          [kernel.kallsyms]   [k] _raw_spin_unlock_irqrestore
   1.84%  swapper          [kernel.kallsyms]   [k] __softirqentry_text_start
   1.64%  swapper          [kernel.kallsyms]   [k] tick_nohz_idle_exit
   1.53%  netperf          [kernel.kallsyms]   [k] _raw_spin_unlock_irq
   1.32%  netperf          [kernel.kallsyms]   [k] preempt_count_sub
   1.27%  swapper          [kernel.kallsyms]   [k] __pi___inval_dcache_area
   1.22%  swapper          [kernel.kallsyms]   [k] check_preemption_disabled
   1.01%  ksoftirqd/0      [kernel.kallsyms]   [k] _raw_spin_unlock_irqrestore

The above results collected on the R-Car V3H Starter Kit board.

Based on the commit 4d86d381 ("ravb: RX checksum offload")...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 62e04b7e ("sh_eth: rename 'sh_eth_cpu_data::hw_crc'") renamed
the field to 'hw_checksum' for the Ether DMAC "intelligent checksum",
however some Ether MACs implement a simpler checksumming scheme, so that
name now seems misleading. Rename that field to 'csmr' as the "intelligent
checksum" is always controlled by the CSMR register.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes: 887feae3 ("socket: Add SO_TIMESTAMP[NS]_NEW")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add __cold to the netdev_<level> logging functions similar to
the use of __cold in the generic printk function.

Using __cold moves all the netdev_<level> logging functions
out-of-line possibly improving code locality and runtime
performance.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/core/sock.c: In function 'sock_setsockopt':
net/core/sock.c:914:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
   sock_set_flag(sk, SOCK_TSTAMP_NEW);
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
net/core/sock.c:915:2: note: here
  case SO_TIMESTAMPING_OLD:
  ^~~~

Fixes: 9718475e ("socket: Add SO_TIMESTAMPING_NEW")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the header search paths -Itools/include and
-Itools/include/uapi are not used. Let's drop the unused code.

We can remove -I. too by fixing up one C file.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: aquantia: number of improvements

This patch series is based on work from Andrew. I adjusted and added
certain parts. The series improves few aspects of driver, no functional
change intended.

v2:
- add my SoB to patch 1
- leave kernel.h in in patch 2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace magic numbers with proper constants. The original patch is
from Andrew, I extended / adjusted certain parts:
- Use decimal bit numbers. The datasheet uses hex bit numbers 0 .. F.
- Order defines from highest to lowest bit numbers
- correct some typos
- add constant MDIO_AN_TX_VEND_INT_MASK2_LINK
- Remove few functional improvements from the patch, they will come as
  a separate patch.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make use of macro PHY_ID_MATCH_MODEL to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove unneeded header includes.

v2:
- leave kernel.h in
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

aquantia_ as a name space prefix is rather long, resulting in lots of
lines needing wrapping, reducing readability. Use the prefix aqr_
instead, which fits with the vendor naming there devices aqr107, for
example.

v2:
- add SoB from Heiner
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After 4effd28c ("bridge: join all-snoopers multicast address"), I
started seeing the following sleep in atomic warnings:

[   26.763893] BUG: sleeping function called from invalid context at mm/slab.h:421
[   26.771425] in_atomic(): 1, irqs_disabled(): 0, pid: 1658, name: sh
[   26.777855] INFO: lockdep is turned off.
[   26.781916] CPU: 0 PID: 1658 Comm: sh Not tainted 5.0.0-rc4 #20
[   26.787943] Hardware name: BCM97278SV (DT)
[   26.792118] Call trace:
[   26.794645]  dump_backtrace+0x0/0x170
[   26.798391]  show_stack+0x24/0x30
[   26.801787]  dump_stack+0xa4/0xe4
[   26.805182]  ___might_sleep+0x208/0x218
[   26.809102]  __might_sleep+0x78/0x88
[   26.812762]  kmem_cache_alloc_trace+0x64/0x28c
[   26.817301]  igmp_group_dropped+0x150/0x230
[   26.821573]  ip_mc_dec_group+0x1b0/0x1f8
[   26.825585]  br_ip4_multicast_leave_snoopers.isra.11+0x174/0x190
[   26.831704]  br_multicast_toggle+0x78/0xcc
[   26.835887]  store_bridge_parm+0xc4/0xfc
[   26.839894]  multicast_snooping_store+0x3c/0x4c
[   26.844517]  dev_attr_store+0x44/0x5c
[   26.848262]  sysfs_kf_write+0x50/0x68
[   26.852006]  kernfs_fop_write+0x14c/0x1b4
[   26.856102]  __vfs_write+0x60/0x190
[   26.859668]  vfs_write+0xc8/0x168
[   26.863059]  ksys_write+0x70/0xc8
[   26.866449]  __arm64_sys_write+0x24/0x30
[   26.870458]  el0_svc_common+0xa0/0x11c
[   26.874291]  el0_svc_handler+0x38/0x70
[   26.878120]  el0_svc+0x8/0xc

while toggling the bridge's multicast_snooping attribute dynamically.

Pass a gfp_t down to igmpv3_add_delrec(), introduce
__igmp_group_dropped() and introduce __ip_mc_dec_group() to take a gfp_t
argument.

Similarly introduce ____ip_mc_inc_group() and __ip_mc_inc_group() to
allow caller to specify gfp_t.

IPv6 part of the patch appears fine.

Fixes: 4effd28c ("bridge: join all-snoopers multicast address")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>