checkpatch complains about missing space around operators.

[mchehab@osg.samsung.com: removed obsolete hunks]
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

checkpatch complains about space after type cast.

[mchehab@osg.samsung.com: removed an obsolete hunk]
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

A NULL comparison can be written as if (var) or if (!var).
Reported by checkpatch.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Add optional reset and standby gpios. The reset gpio is used to reset
the chip in power_on().

The standby gpio is not used currently. It is just unset, so the chip is
not in standby.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Passing a physical address to free_pages() is a bad idea.
config_params->fault_pxl.fpc_table_addr is set to virt_to_phys()
of __get_free_pages() return value; what we should pass to free_pages()
is its phys_to_virt().  ccdc_close() does that properly, but
ccdc_update_raw_params() doesn't.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

changeset 460b6c08 ("tvp5150: Add s_stream subdev operation
support") broke for em28xx-based devices with uses tvp5150. On those
devices, touching the TVP5150_MISC_CTL register causes em28xx to stop
streaming.

I suspect that it uses the 27 MHz clock provided by tvp5150 to feed
em28xx. So, change the logic to do nothing on s_stream if the tvp5150 is
not set up to work with V4L2_MBUS_PARALLEL.

Tested with Hauppauge WinTV USB 2 model 42012 Rev. C186
(USB ID: 2040:4200).

Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The si2165 does not support bandwidth auto-detection.
Reject the request.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Now that this was defined at usb-id.h, update the values for
USB_PID_TERRATEC_CINERGY_S2_R1 and USB_PID_TERRATEC_CINERGY_S2_R2.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Also Add Terratec Cinergy S2 usb id's
Signed-off-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The FIFO is used for ir_raw_event records, however for some historic
reason the FIFO is used on a per byte basis. IMHO this adds unneeded
complexity. Therefore set up the FIFO for ir_raw_event records.

This also allows to define the FIFO statically as part of
ir_raw_event_ctrl instead of having to allocate the FIFO dynamically.
In addition:

- When writing into the FIFO and it's full return ENOSPC instead of
  ENOMEM thus making it easier to tell between "FIFO full" and
  "Dynamic memory allocation failed" when the error is propagated to
  a higher level.
  Also add an error message.

- When reading from the FIFO check whether it's empty.
  This is not strictly needed here but kfifo_out is annotated
  "must check" anyway.

Successfully tested it with the nuvoton-cir driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

When requesting resources use different names for the normal and
the wakeup part. This makes it easier to interpret the output
of e.g. /proc/interrupts and /proc/ioports.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

MyGica/Geniatech S2870 is very similar to the S870 but with dual tuner. The card is recognised as Geniatech STK8096-PVR.

[mchehab@osg.samsung.com: Fix some checkpatch.pl issues]
Signed-off-by: Nicolas Sugino <nsugino@3way.com.ar>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Soon my dibcom.fr/parrot.com-address won't respond anymore.
Thus I'm replacing it. And, while being at it,
let's adapt some other (old) email-addresses as well.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The Documentation/devicetree/bindings/media/i2c/tvp5150.txt DT binding doc
lists "ti,tvp5150" as the device compatible string but the driver does not
have an OF match table. Add the table to the driver so the I2C core can do
an OF style match.
Signed-off-by: Eduard Gavin <egavinc@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The video decoder supports either 8-bit 4:2:2 YUV with discrete syncs
or 8-bit ITU-R BT.656 with embedded syncs output format but currently
BT.656 it's always reported. Allow to configure the format to use via
either platform data or a device tree definition.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

After power-up, the tvp5150 decoder is in a unknown state until the
RESETB pin is driven LOW which reset all the registers and restarts
the chip's internal state machine.

The init sequence has some timing constraints and the RESETB signal
can only be used if the PDN (Power-down) pin is first released.

So, the initialization sequence is as follows:

1- PDN (active-low) is driven HIGH so the chip is power-up
2- A 20 ms delay is needed before sending a RESETB (active-low) signal.
3- The RESETB pulse duration is 500 ns.
4- A 200 us delay is needed for the I2C client to be active after reset.

This patch used as a reference the logic in the IGEPv2 board file from
the ISEE 2.6.37 vendor tree.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Add a Device Tree binding document for the TVP5150 video decoder.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch adds the .g_mbus_config subdev operation to the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch adds the .s_stream subdev operation to the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch adds support for the V4L2_CID_PIXEL_RATE control.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Expand the version detection code to identity the tvp5151.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Move the version detection code to a separate function and restructure
it to prepare for TVP5151 support.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This WARNING was found using the checkpatch tool:
	Block comments use * on the subsequent lines
Signed-off-by: Joseph Marrero <jmarrero@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The v4l2_subdev_sensor_ops structures are never modified, so declare them
as const.

Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Add chip identification for R-Car Gen3.
Signed-off-by: Yoshihiko Mori <yoshihiko.mori.nx@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Use soc_camera_from_vb2q() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The data-shift DT property speficies the number of bits to be shifted,
but the driver still interprets the value as a multiple of two bits as
used by now removed platform data support. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The sequence number counter is incremented on each output buffer, and that
incremented value is used as the sequence number of that buffer. The input
buffer sequence numbering is based just on reading the same counter. If
the input buffer is marked done first, its sequence number ends up being
that of the output buffer - 1.

This is how the resizer works as well.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The function can return negative value.

The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].

[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

use the vb2_buffer_state enum for assigning the state
of the vb2 buffer, along side making isp_pipeline_state
state variable local to the block.
This fixes the following sparse warning as well:
drivers/media/platform/omap3isp/ispvideo.c:497:35: warning: mixing different enum types
drivers/media/platform/omap3isp/ispvideo.c:497:35:     int enum isp_pipeline_state  versus
drivers/media/platform/omap3isp/ispvideo.c:497:35:     int enum vb2_buffer_state
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

When the video buffer queue was stopped before the stream source was started
in omap3isp_streamon(), the buffers were not returned back to videobuf2.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Move the starting of the sensor from the VIDIOC_STREAMON handler to the
videobuf2 queue op start_streaming. This avoids failing starting the stream
after vb2_streamon() has already finished.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Platform drivers needs to export the OF id table and this be built
into the module or udev will not have the necessary information to
autoload the driver module when the device is registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Enable MEDIA_IOC_G_TOPOLOGY ioctl for Kernel 4.6.

This reverts commit be0270ec.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Linux 4.5-rc1

* tag 'v4.5-rc1': (11309 commits)
  Linux 4.5-rc1
  ideapad-laptop: Add Lenovo Yoga 700 to no_hw_rfkill dmi list
  MAINTAINERS: Combine multiple telemetry entries
  intel_telemetry_debugfs: Fix unused warnings in telemetry debugfs
  vmstat: Remove BUG_ON from vmstat_update
  MIPS: zboot: Add support for serial debug using the PROM
  MIPS: zboot: Avoid useless rebuilds
  MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
  MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
  MIPS: bcm963xx: Update bcm_tag field image_sequence
  MIPS: bcm963xx: Move extended flash address to bcm_tag header file
  MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
  MIPS: bcm63xx: nvram: Use nvram structure definition from header file
  MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
  MAINTAINERS: Add KVM for MIPS entry
  MIPS: KVM: Add missing newline to kvm_err()
  MIPS: Move KVM specific opcodes into asm/inst.h
  MIPS: KVM: Use cacheops.h definitions
  MIPS: Break down cacheops.h definitions
  MIPS: Use EXCCODE_ constants with set_except_vector()
  ...

Pull MIPS updates from Ralf Baechle:
 "This is the main pull request for MIPS for 4.5 plus some 4.4 fixes.

  The executive summary:

   - ATH79 platform improvments, use DT bindings for the ATH79 USB PHY.
   - Avoid useless rebuilds for zboot.
   - jz4780: Add NEMC, BCH and NAND device tree nodes
   - Initial support for the MicroChip's DT platform.  As all the device
     drivers are missing this is still of limited use.
   - Some Loongson3 cleanups.
   - The unavoidable whitespace polishing.
   - Reduce clock skew when synchronizing the CPU cycle counters on CPU
     startup.
   - Add MIPS R6 fixes.
   - Lots of cleanups across arch/mips as fallout from KVM.
   - Lots of minor fixes and changes for IEEE 754-2008 support to the
     FPU emulator / fp-assist software.
   - Minor Ralink, BCM47xx and bcm963xx platform support improvments.
   - Support SMP on BCM63168"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits)
  MIPS: zboot: Add support for serial debug using the PROM
  MIPS: zboot: Avoid useless rebuilds
  MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
  MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
  MIPS: bcm963xx: Update bcm_tag field image_sequence
  MIPS: bcm963xx: Move extended flash address to bcm_tag header file
  MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
  MIPS: bcm63xx: nvram: Use nvram structure definition from header file
  MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
  MAINTAINERS: Add KVM for MIPS entry
  MIPS: KVM: Add missing newline to kvm_err()
  MIPS: Move KVM specific opcodes into asm/inst.h
  MIPS: KVM: Use cacheops.h definitions
  MIPS: Break down cacheops.h definitions
  MIPS: Use EXCCODE_ constants with set_except_vector()
  MIPS: Update trap codes
  MIPS: Move Cause.ExcCode trap codes to mipsregs.h
  MIPS: KVM: Make kvm_mips_{init,exit}() static
  MIPS: KVM: Refactor added offsetof()s
  MIPS: KVM: Convert EXPORT_SYMBOL to _GPL
  ...

Merge tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86

Pull x86 platform driver updates from Darren Hart:
 "Emergency travel prevented me from completing my final testing on this
  until today.  Nothing here that couldn't wait until RC1 fixes, but I
  thought it best to get it out sooner rather than later as it does
  contain a build warning fix.

  Summary:

  A build warning fix, MAINTAINERS cleanup, and a new DMI quirk:

  ideapad-laptop:
   - Add Lenovo Yoga 700 to no_hw_rfkill dmi list

  MAINTAINERS:
   - Combine multiple telemetry entries

  intel_telemetry_debugfs:
   - Fix unused warnings in telemetry debugfs"

* tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
  ideapad-laptop: Add Lenovo Yoga 700 to no_hw_rfkill dmi list
  MAINTAINERS: Combine multiple telemetry entries
  intel_telemetry_debugfs: Fix unused warnings in telemetry debugfs

Pull thermal management updates from Zhang Rui:
 "The top merge commit was re-generated yesterday because two topic
  branches were dropped from this pull request in the last minute due to
  some unaddressed comments.  All the other material has been in
  linux-next for quite a while.

  Specifics:

   - Enhance thermal core to handle unexpected device cooling states
     after fresh boot and system resume.  From Zhang Rui and Chen Yu.

   - Several fixes and cleanups on Rockchip and RCAR thermal drivers.
     From Caesar Wang and Kuninori Morimoto.

   - Add Broxton support for Intel processor thermal reporting device
     driver.  From Amy Wiles"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  thermal: trip_point_temp_store() calls thermal_zone_device_update()
  thermal: rcar: rcar_thermal_get_temp() return error if strange temp
  thermal: rcar: check irq possibility in rcar_thermal_irq_xxx()
  thermal: rcar: check every rcar_thermal_update_temp() return value
  thermal: rcar: move rcar_thermal_dt_ids to upside
  thermal: rockchip: Support the RK3399 SoCs in thermal driver
  thermal: rockchip: Support the RK3228 SoCs in thermal driver
  dt-bindings: rockchip-thermal: Support the RK3228/RK3399 SoCs compatible
  thermal: rockchip: fix a trivial typo
  Thermal: Enable Broxton SoC thermal reporting device
  thermal: constify pch_dev_ops structure
  Thermal: do thermal zone update after a cooling device registered
  Thermal: handle thermal zone device properly during system sleep
  Thermal: initialize thermal zone device correctly