- 05 Mar, 2015 15 commits
-
-
David S. Miller authored
Hariprasad Shenai says: ==================== cxgb4: RX Queue related cleanup and fixes This patch series adds a common function to allocate RX queues and queue allocation changes to RDMA CIQ The patches series is created against 'net-next' tree. And includes patches on cxgb4 driver. We have included all the maintainers of respective drivers. Kindly review the change and let us know in case of any review comments. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Hariprasad Shenai authored
To allow for better scalability on systems with large core counts, we will try and allocate enough RDMA Concentrator IQs and MSI/X vectors as we have cores. If we cannot get enough MSI/X vectors, fall back to the minimum required: 1 per adapter rx channel. Also clean up cxgb_enable_msix() to make it readable and correct a bug where the vectors are not correctly assigned if the driver doesn't get the full amount requested. Signed-off-by:
Steve Wise <swise@opengridcomputing.com> Signed-off-by:
Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by:
-
Hariprasad Shenai authored
Adds a common function for all Rx queue allocation. Signed-off-by:
-
Jouni Malinen authored
This extends the design in commit 95850116 ("bridge: Add support for IEEE 802.11 Proxy ARP") with optional set of rules that are needed to meet the IEEE 802.11 and Hotspot 2.0 requirements for ProxyARP. The previously added BR_PROXYARP behavior is left as-is and a new BR_PROXYARP_WIFI alternative is added so that this behavior can be configured from user space when required. In addition, this enables proxyarp functionality for unicast ARP requests for both BR_PROXYARP and BR_PROXYARP_WIFI since it is possible to use unicast as well as broadcast for these frames. The key differences in functionality: BR_PROXYARP: - uses the flag on the bridge port on which the request frame was received to determine whether to reply - block bridge port flooding completely on ports that enable proxy ARP BR_PROXYARP_WIFI: - uses the flag on the bridge port to which the target device of the request belongs - block bridge port flooding selectively based on whether the proxyarp functionality replied Signed-off-by:
Jouni Malinen <jouni@codeaurora.org> Signed-off-by:
-
kbuild test robot authored
> > >> net/ax25/ax25_ip.c:225:26: error: unknown type name 'sturct' > netdev_tx_t ax25_ip_xmit(sturct sk_buff *skb) > ^ > > vim +/sturct +225 net/ax25/ax25_ip.c > > 219 unsigned short type, const void *daddr, > 220 const void *saddr, unsigned int len) > 221 { > 222 return -AX25_HEADER_LEN; > 223 } > 224 > > 225 netdev_tx_t ax25_ip_xmit(sturct sk_buff *skb) > 226 { > 227 kfree_skb(skb); > 228 return NETDEV_TX_OK; Ooops I misspelled struct... Signed-off-by:"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Petri Gynther authored
1. Use c_index and ring->c_index to determine how many TxCBs/TxBDs are ready for cleanup - c_index = the current value of TDMA_CONS_INDEX - TDMA_CONS_INDEX is HW-incremented and auto-wraparound (0x0-0xFFFF) - ring->c_index = __bcmgenet_tx_reclaim() cleaned up to this point on the previous invocation 2. Add bcmgenet_tx_ring->clean_ptr - index of the next TxCB to be cleaned - incremented as TxCBs/TxBDs are processed - value always in range [ring->cb_ptr, ring->end_ptr] 3. Fix incrementing of dev->stats.tx_packets - should be incremented only when tx_cb_ptr->skb != NULL These changes simplify __bcmgenet_tx_reclaim(). Furthermore, Tx ring size can now be any value. With the old code, Tx ring size had to be a power-of-2: num_tx_bds = ring->size; c_index &= (num_tx_bds - 1); last_c_index &= (num_tx_bds - 1); Signed-off-by:Petri Gynther <pgynther@google.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
David S. Miller authored
Alexander Duyck says: ==================== ipv4/fib_trie: Cleanups to prepare for introduction of key vector This patch series is meant to mostly just clean up the fib_trie to prepare it for the introduction of the key_vector. As such there are a number of minor clean-ups such as reformatting the tnode to match the format once the key vector is introduced, some optimizations to drop the need for a leaf parent pointer, and some changes to remove duplication of effort such as the 2 look-ups that were essentially being done per node insertion. v2: Added code to cleanup idx >> n->bits and explain unsigned long logic Added code to prevent allocation when tnode size is larger than size_t ==================== Signed-off-by: -
Alexander Duyck authored
This patch adds code to prevent us from attempting to allocate a tnode with a size larger than what can be represented by size_t. Signed-off-by:
Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by:
-
Alexander Duyck authored
This change updates the fib_table_lookup function so that it is in sync with the fib_find_node function in terms of the explanation for the index check based on the bits value. I have also updated it from doing a mask to just doing a compare as I have found that seems to provide more options to the compiler as I have seen it turn this into a shift of the value and test under some circumstances. In addition I addressed one minor issue in which we kept computing the key ^ n->key when checking the fib aliases. I pulled the xor out of the loop in order to reduce the number of memory reads in the lookup. As a result we should save a couple cycles since the xor is only done once much earlier in the lookup. Signed-off-by:
-
Alexander Duyck authored
The fib_table was wrapped in several places with an rcu_read_lock/rcu_read_unlock however after looking over the code I found several spots where the tables were being accessed as just standard pointers without any protections. This change fixes that so that all of the proper protections are in place when accessing the table to take RCU replacement or removal of the table into account. Signed-off-by:
-
Alexander Duyck authored
If we are going to compact the leaf and tnode we first need to make sure the fields are all in the same place. In that regard I am moving the leaf pointer which represents the fib_alias hash list to occupy what is currently the first key_vector pointer. Signed-off-by:
-
Alexander Duyck authored
This change makes it so that the insert and delete functions make use of the tnode pointer returned in the fib_find_node call. By doing this we will not have to rely on the parent pointer in the leaf which will be going away soon. Signed-off-by:
-
Alexander Duyck authored
This change makes it so that the parent pointer is returned by reference in fib_find_node. By doing this I can use it to find the parent node when I am performing an insertion and I don't have to look for it again in fib_insert_node. Signed-off-by:
-
Alexander Duyck authored
This change makes it so that leaf_walk_rcu takes a tnode and a key instead of the trie and a leaf. The main idea behind this is to avoid using the leaf parent pointer as that can have additional overhead in the future as I am trying to reduce the size of a leaf down to 16 bytes on 64b systems and 12b on 32b systems. Signed-off-by:
-
Alexander Duyck authored
This change makes it so that we only call resize on the tnodes, instead of from each of the leaves. By doing this we can significantly reduce the amount of time spent resizing as we can update all of the leaves in the tnode first before we make any determinations about resizing. As a result we can simply free the tnode in the case that all of the leaves from a given tnode are flushed instead of resizing with each leaf removed. Signed-off-by:
-
- 04 Mar, 2015 25 commits
-
-
David S. Miller authored
Merge tag 'linux-can-next-for-4.1-20150304' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next Marc Kleine-Budde says: ==================== pull-request: can-next 2015-03-04 this is a pull request of 3 patches for net-next/master. Aaron Wu contributes three patches for the blackfin can driver, which cleans up the driver and makes use of more platform independent code. ==================== Signed-off-by:
-
Wu Fengguang authored
Signed-off-by:
Fengguang Wu <fengguang.wu@intel.com> Signed-off-by:
-
David S. Miller authored
Sathya Perla says: ==================== be2net: patch set Hi Dave, the following patch set includes three feature additions relating to SR-IOV to be2net. Patch 1 avoid creating a non-RSS default RXQ when FW allows it. This prevents wasting one RXQ for each VF. Patch 2 adds support for evenly distributing all queue & filter resources across VFs. The FW informs the driver as to which resources are distributable. Patch 3 implements the sriov_configure PCI method to allow runtime enablement of VFs via sysfs. Pls consider applying this patch-set to the net-next tree. Thanks! ==================== Signed-off-by: -
Vasundhara Volam authored
This patch implements the .sriov_configure() PCI method to allow for runtime enabling/disabling of VFs. The module param "num_vfs" is now deprecated. At the time of driver load the PF-pool resources are allocated to the PF. When the user enables VFs, the resources are then re-distributed across PFs and VFs based on the number of VFs enabled. Signed-off-by:
Vasundhara Volam <vasundhara.volam@emulex.com> Signed-off-by:
Sathya Perla <sathya.perla@emulex.com> Signed-off-by:
-
Vasundhara Volam authored
When SR-IOV is enabled in the adapter, the FW distributes resources evenly across the PF and it's VFs. This is currently done only for some resources. This patch adds support for a new cmd that queries the FW for the list of resources for which the distribution is allowed and distributes them accordingly. Signed-off-by:
-
Vasundhara Volam authored
On BE2, BE3 and Skhawk-R chips one non-RSS (called "default") RXQ was needed to receive non-IP traffic. Some FW versions now export a capability called IFACE_FLAGS_DEFQ_RSS where this requirement doesn't hold. On such FWs the driver now does not create the non-RSS default queue. This prevents wasting one RXQ per VF. Signed-off-by:
-
Michal Simek authored
Remove Kconfig dependency and enable driver for all ARCHs. Signed-off-by:
Michal Simek <michal.simek@xilinx.com> Acked-by:
Sören Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by:
-
David S. Miller authored
Ben Hutchings says: ==================== sh_eth changes for net-next Some minor new features and fixes. These depend in part on the series I sent earlier for net, specifically "sh_eth: WARN on access to a register not implemented in a particular chip" depends on "sh_eth: Fix RX recovery on R-Car in case of RX ring underrun". ==================== Signed-off-by: -
Ben Hutchings authored
The statistics registers have write-clear behaviour, which means we will lose any increment between the read and write. Mitigate this by only clearing when we read a non-zero value, so we will never falsely report a total of zero. This also saves time as we only handle error statistics here and they won't often be incremented. Signed-off-by:
Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by:
-
Ben Hutchings authored
Signed-off-by:
-
Ben Hutchings authored
There are many different sets of registers implemented by the different versions of this controller, and we can only expect this to get more complicated in future. Limit how much ethtool needs to know by including an explicit bitmap of which registers are included in the dump, allowing room for future growth in the number of possible registers. As I don't have datasheets for all of these, I've only included registers that are: - defined in all 5 register type arrays, or - used by the driver, or - documented in the datasheet I have Add one new capability flag so we can tell whether the RTRATE register is implemented. Delete the TSU_ADRL0 and TSU_ADR{H,L}31 definitions, as they weren't used and the address table is already assumed to be contiguous. Signed-off-by: -
Ben Hutchings authored
Currently we may silently read/write a register at offset 0. Change this to WARN and then ignore the write or read-back all-ones. Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
-
Ben Hutchings authored
At least on the R8A7790, RFS8 reflects the RINT8 (multicast) MAC status flag. Signed-off-by:
-
Aaron Wu authored
Header file was in arch dependent location arch/blackfin/include/asm/bfin_can.h, Now move and merge the useful contents of header file into driver code, note the original header file is reserved for full registers set access test by other code so it survives. Signed-off-by:
Aaron Wu <Aaron.wu@analog.com> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Aaron Wu authored
Blackfin was built without MMU, old driver code access the IO space by physical address, introduce the ioremap approach to be compitable with the common style supporting MMU enabled arch. Signed-off-by:
-
Aaron Wu authored
Replace the blackfin arch dependent style of bfin_read/bfin_write with common readw/writew Signed-off-by:
-
David S. Miller authored
Eric W. Biederman says: ==================== Basic MPLS support take 2 On top of my two pending neighbour table prep patches here is the mpls support refactored to use them, and edited to not drop routes when an interface goes down. Additionally the addition of RTA_LLGATEWAY has been replaced with the addtion of RTA_VIA. RTA_VIA being an attribute that includes the address family as well as the address of the next hop. MPLS is at it's heart simple and I have endeavoured to maintain that simplicity in my implemenation. This is an implementation of a RFC3032 forwarding engine, and basic MPLS egress logic. Which should make linux sufficient to be a mpls forwarding node or to be a LSA (Label Switched Router) as it says in all of the MPLS documents. The ingress support will follow but it deserves it's own discussion so I am pushing it separately. ==================== Signed-off-by: -
Eric W. Biederman authored
Unlike IPv4 this code notifies on all cases where mpls routes are added or removed and it never automatically removes routes. Avoiding both the userspace confusion that is caused by omitting route updates and the possibility of a flood of netlink traffic when an interface goes doew. For now reserved labels are handled automatically and userspace is not notified. Signed-off-by:
-
Eric W. Biederman authored
This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by:
-
Eric W. Biederman authored
Reading and writing addresses in network byte order in netlink is traditional and I see no reason to change that. MPLS is interesting as effectively it has variabely length addresses (the MPLS label stack). To represent these variable length addresses in netlink I use a valid MPLS label stack (complete with stop bit). This achieves two things: a well defined existing format is used, and the data can be interpreted without looking at it's length. Not needed to look at the length to decode the variable length network representation allows existing userspace functions such as inet_ntop to be used without needed to change their prototype. Signed-off-by:
-
Eric W. Biederman authored
mpls_route_add and mpls_route_del implement the basic logic for adding and removing Next Hop Label Forwarding Entries from the MPLS input label map. The addition and subtraction is done in a way that is consistent with how the existing routing table in Linux are maintained. Thus all of the work to deal with NLM_F_APPEND, NLM_F_EXCL, NLM_F_REPLACE, and NLM_F_CREATE. Cases that are not clearly defined such as changing the interpretation of the mpls reserved labels is not allowed. Because it seems like the right thing to do adding an MPLS route without specifying an input label and allowing the kernel to pick a free label table entry is supported. The implementation is currently less than optimal but that can be changed. As I don't have anything else to test with only ethernet and the loopback device are the only two device types currently supported for forwarding MPLS over. Signed-off-by:
-
Eric W. Biederman authored
This sysctl gives two benefits. By defaulting the table size to 0 mpls even when compiled in and enabled defaults to not forwarding any packets. This prevents unpleasant surprises for users. The other benefit is that as mpls labels are allocated locally a dense table a small dense label table may be used which saves memory and is extremely simple and efficient to implement. This sysctl allows userspace to choose the restrictions on the label table size userspace applications need to cope with. Signed-off-by:
-
Eric W. Biederman authored
This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by:
-
Eric W. Biederman authored
This refactoring is needed to allow more than just mpls gso support to be built into the mpls moddule. Reviewed-by:
Simon Horman <horms@verge.net.au> Signed-off-by:
-
David S. Miller authored
Eric W. Biederman says: ==================== Neighbour table prep for MPLS In preparation for using the IPv4 and IPv6 neighbour tables in my mpls code this patchset factors out ___neigh_lookup_noref from __ipv4_neigh_lookup_noref, __ipv6_lookup_noref and neigh_lookup. Allowing the lookup logic to be shared between the different implementations. At what appears to be no cost. (Aka the same assembly is generated for ip6_finish_output2 and ip_finish_output2). After that I add a simple function that takes an address family and an address consults the neighbour table and sends the packet to the appropriate location. The address family argument decoupls callers of neigh_xmit from the addresses families the packets are sent over. (Aka The ipv6 module can be loaded after mpls and a previously configured ipv6 next hop will start working). The refactoring in ___neigh_lookup_noref may be a bit overkill but it feels like the right thing to do. Especially since the same code is generated. ==================== Signed-off-by:
-
