Skip to content

L
linux
Switch branch/tag
  1. 01 Dec, 2008 33 commits
  3. 30 Nov, 2008 7 commits
    • Paul Mackerras's avatar
      powerpc: Fix system calls on Cell entered with XER.SO=1 · ab598b66
      Paul Mackerras authored 
      It turns out that on Cell, on a kernel with CONFIG_VIRT_CPU_ACCOUNTING
= y, if a program sets the SO (summary overflow) bit in the XER and
then does a system call, the SO bit in CR0 will be set on return
regardless of whether the system call detected an error.  Since CR0.SO
is used as the error indication from the system call, this means that
all system calls appear to fail.

The reason is that the workaround for the timebase bug on Cell uses a
compare instruction.  With CONFIG_VIRT_CPU_ACCOUNTING = y, the
ACCOUNT_CPU_USER_ENTRY macro reads the timebase, so we end up doing a
compare instruction, which copies XER.SO to CR0.SO.  Since we were
doing this in the system call entry patch after clearing CR0.SO but
before saving the CR, this meant that the saved CR image had CR0.SO
set if XER.SO was set on entry.

This fixes it by moving the clearing of CR0.SO to after the
ACCOUNT_CPU_USER_ENTRY call in the system call entry path.
Signed-off-by: default avatarPaul Mackerras <paulus@samba.org>
Acked-by: default avatarArnd Bergmann <arnd@arndb.de>
Acked-by: default avatarBenjamin Herrenschmidt <benh@kernel.crashing.org>
      ab598b66
    • Arnd Bergmann's avatar
      powerpc/cell: Fix GDB watchpoints, again · 960cedb4
      Arnd Bergmann authored 
      An earlier patch from Jens Osterkamp attempted to fix GDB
watchpoints by enabling the DABRX register at boot time.
Unfortunately, this did not work on SMP setups, where
secondary CPUs were still using the power-on DABRX value.

This introduces the same change for secondary CPUs on cell
as well.
Reported-by: default avatarUlrich Weigand <Ulrich.Weigand@de.ibm.com>
Tested-by: default avatarUlrich Weigand <Ulrich.Weigand@de.ibm.com>
Signed-off-by: default avatarArnd Bergmann <arnd@arndb.de>
Signed-off-by: default avatarPaul Mackerras <paulus@samba.org>
      960cedb4
    • Arnd Bergmann's avatar
      powerpc/mpic: Don't reset affinity for secondary MPIC on boot · cc353c30
      Arnd Bergmann authored 
      Kexec/kdump currently fails on the IBM QS2x blades when the kexec happens
on a CPU other than the initial boot CPU.  It turns out that this is the
result of mpic_init trying to set affinity of each interrupt vector to the
current boot CPU.

As far as I can tell,  the same problem is likely to exist on any
secondary MPIC, because they have to deliver interrupts to the first
output all the time. There are two potential solutions for this: either
not set up affinity at all for secondary MPICs, or assume that a single
CPU output is connected to the upstream interrupt controller and hardcode
affinity to that per architecture.

This patch implements the second approach, defaulting to the first output.
Currently, all known secondary MPICs are routed to their upstream port
using the first destination, so we hardcode that.
Signed-off-by: default avatarArnd Bergmann <arnd@arndb.de>
Signed-off-by: default avatarPaul Mackerras <paulus@samba.org>
      cc353c30
    • Arnd Bergmann's avatar
      powerpc/cell/axon-msi: Retry on missing interrupt · d015fe99
      Arnd Bergmann authored 
      The MSI capture logic for the axon bridge can sometimes
lose interrupts in case of high DMA and interrupt load,
when it signals an MSI interrupt to the MPIC interrupt
controller while we are already handling another MSI.

Each MSI vector gets written into a FIFO buffer in main
memory using DMA, and that DMA access is normally flushed
by the actual interrupt packet on the IOIF.  An MMIO
register in the MSIC holds the position of the last
entry in the FIFO buffer that was written.  However,
reading that position does not flush the DMA, so that
we can observe stale data in the buffer.

In a stress test, we have observed the DMA to arrive
up to 14 microseconds after reading the register.

This patch works around this problem by retrying the
access to the FIFO buffer.

We can reliably detect the conditioning by writing
an invalid MSI vector into the FIFO buffer after
reading from it, assuming that all MSIs we get
are valid.  After detecting an invalid MSI vector,
we udelay(1) in the interrupt cascade for up to
100 times before giving up.
Signed-off-by: default avatarArnd Bergmann <arnd@arndb.de>
Signed-off-by: default avatarPaul Mackerras <paulus@samba.org>
      d015fe99
    • Dave Hansen's avatar
      powerpc: Fix boot freeze on machine with empty memory node · 4a618669
      Dave Hansen authored 
      I got a bug report about a distro kernel not booting on a particular
machine.  It would freeze during boot:

> ...
> Could not find start_pfn for node 1
> [boot]0015 Setup Done
> Built 2 zonelists in Node order, mobility grouping on.  Total pages: 123783
> Policy zone: DMA
> Kernel command line:
> [boot]0020 XICS Init
> [boot]0021 XICS Done
> PID hash table entries: 4096 (order: 12, 32768 bytes)
> clocksource: timebase mult[7d0000] shift[22] registered
> Console: colour dummy device 80x25
> console handover: boot [udbg0] -> real [hvc0]
> Dentry cache hash table entries: 1048576 (order: 7, 8388608 bytes)
> Inode-cache hash table entries: 524288 (order: 6, 4194304 bytes)
> freeing bootmem node 0

I've reproduced this on 2.6.27.7.  It is caused by commit
8f64e1f2 ("powerpc: Reserve in bootmem
lmb reserved regions that cross NUMA nodes").

The problem is that Jon took a loop which was (in pseudocode):

	for_each_node(nid)
		NODE_DATA(nid) = careful_alloc(nid);
		setup_bootmem(nid);
		reserve_node_bootmem(nid);

and broke it up into:

	for_each_node(nid)
		NODE_DATA(nid) = careful_alloc(nid);
		setup_bootmem(nid);
	for_each_node(nid)
		reserve_node_bootmem(nid);

The issue comes in when the 'careful_alloc()' is called on a node with
no memory.  It falls back to using bootmem from a previously-initialized
node.  But, bootmem has not yet been reserved when Jon's patch is
applied.  It gives back bogus memory (0xc000000000000000) and pukes
later in boot.

The following patch collapses the loop back together.  It also breaks
the mark_reserved_regions_for_nid() code out into a function and adds
some comments.  I think a huge part of introducing this bug is because
for loop was too long and hard to read.

The actual bug fix here is the:

+		if (end_pfn <= node->node_start_pfn ||
+		    start_pfn >= node_end_pfn)
+			continue;
Signed-off-by: default avatarDave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: default avatarPaul Mackerras <paulus@samba.org>
      4a618669
    • Adhemerval Zanella's avatar
      powerpc: Fix IRQ assignment for some PCIe devices · 4b824de9
      Adhemerval Zanella authored 
      Currently, some PCIe devices on POWER6 machines do not get interrupts
assigned correctly.  The problem is that OF doesn't create an
"interrupt" property for them.  The fix is for of_irq_map_pci to fall
back to using the value in the PCI interrupt-pin register in config
space, as we do when there is no OF device-tree node for the device.

I have verified that this works fine with a pair of Squib-E SAS
adapter on a P6-570.
Acked-by: default avatarBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: default avatarPaul Mackerras <paulus@samba.org>
      4b824de9
    • Linus Torvalds's avatar
      Merge git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6 · a6e470fd
      Linus Torvalds authored 
      * git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
  parisc: struct device - replace bus_id with dev_name(), dev_set_name()
  parisc: fix kernel crash when unwinding a userspace process
  parisc: __kernel_time_t is always long
      a6e470fd
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7