- 23 Aug, 2011 40 commits
-
-
Arend van Spriel authored
The crc8 function is now available as a library function provided by kernel module crc8.ko. The function has been removed from brcmutil module and srom.c now uses crc8 library function. Reviewed-by:
Henry Ptasinski <henryp@broadcom.com> Reviewed-by:
Roland Vossen <rvossen@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Henry Ptasinski authored
brcmsmac doesn't yet use bcma, but both drivers attempt to claim the same device. For now, turn of brcmsmac if bcma is enabled. Signed-off-by:
-
Roland Vossen authored
Certain Mips based, big endian Broadcom products contain a memory window for endianness swap purposes. However, this is too system specific for this driver as there are more big endian platforms to support. Thus, this 'window' functionality is not to be used and can be removed. The swap window would be a performance improvement and could be provided with a dedicated mapping function in the platform specific code. Tested on BCM63281. Reviewed-by:
Jonas Gorski <jonas.gorski@gmail.com> Signed-off-by:
-
Arend van Spriel authored
The inline function dma_spin_for_len() was defined for MIPS platforms but the problem only occurs with dma of the PCI core in bcm47xx chips. This patch restricts the function further to BCM47XX platforms only. Tested on BCM63281. Reviewed-by:
-
Arend van Spriel authored
The driver contained conditional code for resolving issue with dma transaction reordering. This code was conditionalized using __mips__ macro, but it actually is specific to bcm47xx chips. This patch replaces it for the more speficic CONFIG_BCM47XX macro. Tested on BCM63281. Reviewed-by:
-
Arend van Spriel authored
The include <asm/addrspace.h> has been removed as it is not needed. None of the definitions from it are used in the source file. Tested on BCM63281. Reviewed-by:
-
Henry Ptasinski authored
The firmware files are encoded as little-endian. Do the appropriate swapping for big-endian platforms. Tested on Mac G5 PPC and BCM63281. Signed-off-by:
-
Henry Ptasinski authored
Swapping the addresses is unnecessary, since the swaps are handled by the underlying platform code (i.e. readb() etc. handle any necessary swapping). Tested on Mac G5 PPC and BCM63281. Signed-off-by:
-
Henry Ptasinski authored
The original implementation iterated over the data in buf+1 through buf+size, whereas it should have been over the data in buf through buf+size-1. Tested on Mac G5 PPC and BCM63281. Signed-off-by:
-
Arend van Spriel authored
The macro BUS_SWAP32(a) expanded to (a) which was fine for a little endian system. For big endian platform this should do as the name implies. As the driver is intended for PCI which is little-endian the macro cpu_to_le32() can be used instead. Reviewed-by:
-
Arend van Spriel authored
Four macros with PHYSADDR name prefix are not doing a lot and complicate code readability. These have been expanded in the source code and consequently removed the definitions. Reviewed-by:
-
Arend van Spriel authored
The macros W_SM and R_SM are not doing much conversion of the macro parameters and complicate code readability without good cause. It is more clear to remove usage of the macros expanding it in the source code. Reviewed-by:
-
Franky Lin authored
Remove improper usage of void * in dhd_linux.c and dhd_sdio.c Reported-by:
Julian Calaby <julian.calaby@gmail.com> Reviewed-by:
-
Roland Vossen authored
Code cleanup. Replaced void pointers by less generic pointer types. Reported-by:
-
Roland Vossen authored
Code cleanup. Otp is 'One Time Programmable' functionality. Replaced void pointers by less generic pointer types. Reported-by:
-
Roland Vossen authored
Code cleanup. Replaced by less generic pointer types. Reported-by:
-
Roland Vossen authored
Code cleanup. Replace void * related to PCI functionality by less generic pointer types. Reported-by:
-
Franky Lin authored
Get rid of some unused void *data parameter Reviewed-by:
-
Franky Lin authored
Remove legacy dead code of SDTEST Reviewed-by:
-
Franky Lin authored
Remove redundant complete function pointer in send/recv buffer interface. Reviewed-by:
-
Franky Lin authored
Use brcmf_sdioh_request_byte directly instead of calling brcmf_sdioh_cfg_read and brcmf_sdioh_cfg_write in brcmfmac Reviewed-by:
-
Franky Lin authored
Code cleanup for brcmfmac Reviewed-by:
-
Franky Lin authored
brcmfmac wrapper function cleanup Reviewed-by:
-
Franky Lin authored
brcmfmac wrapper function cleanup Reviewed-by:
-
Franky Lin authored
brcmfmac wrapper function cleanup Reviewed-by:
-
Franky Lin authored
fullmac wrapper function cleanup. Reviewed-by:
-
Franky Lin authored
wext support code have been removed a while ago. This patch removes the traces left behind. Reviewed-by:
-
Franky Lin authored
Use sdio function pointer stored in struct brcmf_sdio_dev instead of those in gInstance. Reviewed-by:
-
Franky Lin authored
Use brcmf_sdio_dev as the unified structure to store information of device. Reviewed-by:
-
Franky Lin authored
Iovar IOV_BLOCKSIZE code is not actually setting the sdio function's block size. Use cur_blksize provided by mmc core where necessary. Reviewed-by:
-
Arend van Spriel authored
In wl_cfg80211.c two semaphores were used to trigger a task to process an event. The wait queues are better suited for that purpose. This also removes checkpatch warning on sema_init() calls in this source file. Reviewed-by:
Franky Lin <frankyl@broadcom.com> Signed-off-by:
-
Arend van Spriel authored
The only remaining TODO item has been tackled so it was removed. No other TODO items left. Reviewed-by:
-
Arend van Spriel authored
Several issue have been reported building the driver on big endian systems. Following commits were done on driver Kconfig: d4620396 Staging: brcm80211: disable drivers except for X86 or MIPS platforms 15e5201d Staging: brcm80211: disable drivers for PPC platforms These problems have been resolved so the added 'depends' lines in the Kconfig have been removed. Compile tested it for following architectures: little endian x86 x86_64 arm mips big endian ppc64 sparc64 mips Reported-by:
David S. Miller <davem@davemloft.net> Reported-by:
Stephen Rothwell <sfr@canb.auug.org.au> Reported-by:
-
Arend van Spriel authored
Building for the ARM resulted in a compiler warning about usage of a possibly uninitialized variable. The warning is valid and the code has been fixed accordingly. Reviewed-by:
-
Pieter-Paul Giesberts authored
Due to missing memset function declaration. Reviewed-by:
-
Roland Vossen authored
Code cleanup. Watchdog function served no purpose since it had an empty body. Reviewed-by:
-
Roland Vossen authored
The AMPDU module was never registered, so it does not have to be unregistered. Reviewed-by:
-
Roland Vossen authored
Code cleanup. Replaced void * by less generic pointer types. Reviewed-by:
-
Roland Vossen authored
Code cleanup. Since the softmac driver only supports a PCI(e) bus, the void * could be replaced with a less generic type. Reviewed-by:
-
Roland Vossen authored
Code cleanup. For the softmac, the 'bustype' in use is always PCI_BUS. Hence code related to dealing with different bus types (eg: PCI_BUS, JTAG_BUS, SI_BUS) could be removed. Reviewed-by:
-
