Skip to content

L
linux
Switch branch/tag
  1. 20 Nov, 2018 2 commits
  3. 19 Nov, 2018 19 commits
    • David S. Miller's avatar
      Merge branch 'sctp-add-subscribe-per-asoc-and-sockopt-SCTP_EVENT' · cfc6731d
      David S. Miller authored 
      Xin Long says:

====================
sctp: add subscribe per asoc and sockopt SCTP_EVENT

This patchset mainly adds the Event Subscription sockopt described in
rfc6525#section-6.2:

"Subscribing to events as described in [RFC6458] uses a setsockopt()
call with the SCTP_EVENT socket option.  This option takes the
following structure, which specifies the association, the event type
(using the same value found in the event type field), and an on/off
boolean.

  struct sctp_event {
    sctp_assoc_t se_assoc_id;
    uint16_t     se_type;
    uint8_t      se_on;
  };

The user fills in the se_type field with the same value found in the
strreset_type field, i.e., SCTP_STREAM_RESET_EVENT.  The user will
also fill in the se_assoc_id field with either the association to set
this event on (this field is ignored for one-to-one style sockets) or
one of the reserved constant values defined in [RFC6458].  Finally,
the se_on field is set with a 1 to enable the event or a 0 to disable
the event."

As for the old SCTP_EVENTS Option with struct sctp_event_subscribe,
it's being DEPRECATED.

v1->v2:
  - fix some key word in changelog that triggerred the filters at
    vger.kernel.org.
v2->v3:
  - fix an array out of bounds noticed by Neil in patch 1/4.
====================
Acked-by: default avatarNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      cfc6731d
    • Xin Long's avatar
      sctp: add sockopt SCTP_EVENT · 480ba9c1
      Xin Long authored 
      This patch adds sockopt SCTP_EVENT described in rfc6525#section-6.2.
With this sockopt users can subscribe to an event from a specified
asoc.
Signed-off-by: default avatarXin Long <lucien.xin@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      480ba9c1
    • Xin Long's avatar
      sctp: rename enum sctp_event to sctp_event_type · 88ee48c1
      Xin Long authored 
      sctp_event is a structure name defined in RFC for sockopt
SCTP_EVENT. To avoid the conflict, rename it.
Signed-off-by: default avatarXin Long <lucien.xin@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      88ee48c1
    • Xin Long's avatar
      sctp: add subscribe per asoc · a1e3a059
      Xin Long authored 
      The member subscribe should be per asoc, so that sockopt SCTP_EVENT
in the next patch can subscribe a event from one asoc only.
Signed-off-by: default avatarXin Long <lucien.xin@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      a1e3a059
    • Xin Long's avatar
      sctp: define subscribe in sctp_sock as __u16 · 2cc0eeb6
      Xin Long authored 
      The member subscribe in sctp_sock is used to indicate to which of
the events it is subscribed, more like a group of flags. So it's
better to be defined as __u16 (2 bytpes), instead of struct
sctp_event_subscribe (13 bytes).

Note that sctp_event_subscribe is an UAPI struct, used on sockopt
calls, and thus it will not be removed. This patch only changes
the internal storage of the flags.
Signed-off-by: default avatarXin Long <lucien.xin@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      2cc0eeb6
    • David S. Miller's avatar
      Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net · f2be6d71
      David S. Miller authored
      f2be6d71
    • Linus Torvalds's avatar
      Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net · f2ce1065
      Linus Torvalds authored 
      Pull networking fixes from David Miller:

 1) Fix some potentially uninitialized variables and use-after-free in
    kvaser_usb can drier, from Jimmy Assarsson.

 2) Fix leaks in qed driver, from Denis Bolotin.

 3) Socket leak in l2tp, from Xin Long.

 4) RSS context allocation fix in bnxt_en from Michael Chan.

 5) Fix cxgb4 build errors, from Ganesh Goudar.

 6) Route leaks in ipv6 when removing exceptions, from Xin Long.

 7) Memory leak in IDR allocation handling of act_pedit, from Davide
    Caratti.

 8) Use-after-free of bridge vlan stats, from Nikolay Aleksandrov.

 9) When MTU is locked, do not force DF bit on ipv4 tunnels. From
    Sabrina Dubroca.

10) When NAPI cached skb is reused, we must set it to the proper initial
    state which includes skb->pkt_type. From Eric Dumazet.

11) Lockdep and non-linear SKB handling fix in tipc from Jon Maloy.

12) Set RX queue properly in various tuntap receive paths, from Matthew
    Cover.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
  tuntap: fix multiqueue rx
  ipv6: Fix PMTU updates for UDP/raw sockets in presence of VRF
  tipc: don't assume linear buffer when reading ancillary data
  tipc: fix lockdep warning when reinitilaizing sockets
  net-gro: reset skb->pkt_type in napi_reuse_skb()
  tc-testing: tdc.py: Guard against lack of returncode in executed command
  tc-testing: tdc.py: ignore errors when decoding stdout/stderr
  ip_tunnel: don't force DF when MTU is locked
  MAINTAINERS: Add entry for CAKE qdisc
  net: bridge: fix vlan stats use-after-free on destruction
  socket: do a generic_file_splice_read when proto_ops has no splice_read
  net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
  Revert "net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs"
  net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
  net/sched: act_pedit: fix memory leak when IDR allocation fails
  net: lantiq: Fix returned value in case of error in 'xrx200_probe()'
  ipv6: fix a dst leak when removing its exception
  net: mvneta: Don't advertise 2.5G modes
  drivers/net/ethernet/qlogic/qed/qed_rdma.h: fix typo
  net/mlx4: Fix UBSAN warning of signed integer overflow
  ...
      f2ce1065
    • Matthew Cover's avatar
      tuntap: fix multiqueue rx · 8ebebcba
      Matthew Cover authored 
      When writing packets to a descriptor associated with a combined queue, the
packets should end up on that queue.

Before this change all packets written to any descriptor associated with a
tap interface end up on rx-0, even when the descriptor is associated with a
different queue.

The rx traffic can be generated by either of the following.
  1. a simple tap program which spins up multiple queues and writes packets
     to each of the file descriptors
  2. tx from a qemu vm with a tap multiqueue netdev

The queue for rx traffic can be observed by either of the following (done
on the hypervisor in the qemu case).
  1. a simple netmap program which opens and reads from per-queue
     descriptors
  2. configuring RPS and doing per-cpu captures with rxtxcpu

Alternatively, if you printk() the return value of skb_get_rx_queue() just
before each instance of netif_receive_skb() in tun.c, you will get 65535
for every skb.

Calling skb_record_rx_queue() to set the rx queue to the queue_index fixes
the association between descriptor and rx queue.
Signed-off-by: default avatarMatthew Cover <matthew.cover@stackpath.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      8ebebcba
    • David Ahern's avatar
      ipv6: Fix PMTU updates for UDP/raw sockets in presence of VRF · 7ddacfa5
      David Ahern authored 
      Preethi reported that PMTU discovery for UDP/raw applications is not
working in the presence of VRF when the socket is not bound to a device.
The problem is that ip6_sk_update_pmtu does not consider the L3 domain
of the skb device if the socket is not bound. Update the function to
set oif to the L3 master device if relevant.

Fixes: ca254490 ("net: Add VRF support to IPv6 stack")
Reported-by: default avatarPreethi Ramachandra <preethir@juniper.net>
Signed-off-by: default avatarDavid Ahern <dsahern@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      7ddacfa5
    • Shalom Toledo's avatar
      mlxsw: spectrum: Expose discard counters via ethtool · bae4e109
      Shalom Toledo authored 
      Expose packets discard counters via ethtool to help with debugging.
Signed-off-by: default avatarShalom Toledo <shalomt@mellanox.com>
Reviewed-by: default avatarJiri Pirko <jiri@mellanox.com>
Signed-off-by: default avatarIdo Schimmel <idosch@mellanox.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      bae4e109
    • Eric Dumazet's avatar
      tun: use netdev_alloc_frag() in tun_napi_alloc_frags() · aa6daaca
      Eric Dumazet authored 
      In order to cook skbs in the same way than Ethernet drivers,
it is probably better to not use GFP_KERNEL, but rather
use the GFP_ATOMIC and PFMEMALLOC mechanisms provided by
netdev_alloc_frag().

This would allow to use tun driver even in memory stress
situations, especially if swap is used over this tun channel.

Fixes: 90e33d45 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: default avatarEric Dumazet <edumazet@google.com>
Cc: Petar Penkov <peterpenkov96@gmail.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      aa6daaca
    • David S. Miller's avatar
      Merge branch 'IP101GR-devicetree-based-configuration-of-SEL_INTR32' · 05b0e1d6
      David S. Miller authored 
      Martin Blumenstingl says:

====================
IP101GR: devicetree based configuration of SEL_INTR32

The IP101GR is a 32-pin QFN package variant of the IP101G/IP101GA
Ethernet PHY. Due to it's limited amount of pins the RXER (receive
error) and INTR32 (interrupt) functions share pin 21.

The goal of this series is:
- some small cleanups in patches 3, 4 and 5
- allowing the kernel to detect IRQ floods on boards where the IP101GR
  is configured in RXER mode but the RXER line is configured on the
  host SoC as interrupt line (patch 6)
- configuration of the SEL_INTR32 register so we can use the interrupt
  function on boards where the RXER/INTR32 pin (pin 21) is routed to
  one of the host SoC's interrupt inputs (patches 1, 2, 7)

A use-case where this is needed is the Endless Mini (EC-100). I have
tested my changes on that board. This also confirms that Heiner
Kallweit's recent icplus.c PHY driver changes are working (at least on
my setup).

This series is based on net-next commit 7c460cf9 ("net: aquantia:
fix spelling mistake "specfield" -> "specified"")

Changes since v1 at [0]:
- collected Andrew's Reviewed-by's (thank you!)
- updated description of patch #2 to explain why two properties were
  added instead of adding an "this is a IP101GR" property
- validate that there's no conflicting configuration in patch #7
- rebased on top of latest net-next

[0] https://patchwork.ozlabs.org/cover/999371/
====================
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      05b0e1d6
    • Martin Blumenstingl's avatar
      net: phy: icplus: allow configuring the interrupt function on IP101GR · f2f1a847
      Martin Blumenstingl authored 
      The IP101GR is a 32-pin QFN package variant of the IP101G/IP101GA
Ethernet PHY. Due to it's limited amount of pins the RXER (receive
error) and INTR32 (interrupt) functions share pin 21.
By default the PHY is configured to output the "receive error" status on
pin 21. Depending on the board layout and requirements we may want to
re-configure the PHY to output the interrupt signal there.

The mode of pin 21 can be configured in the "Digital I/O Specific
Control Register" (register 29), bit 2:
- 0 = RXER function
- 1 = INTR(32) function

Depending on the devicetree configuration we will now:
- change the mode to either ther RXER or INTR32 function
- keep the SEL_INTR32 value set by the bootloader (default) if no
  configuration is provided (to ensure that we're not breaking existing
  boards)
- error out if conflicting configuration is given (RXER and INTR32 mode
  are enabled at the same time)
Signed-off-by: default avatarMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      f2f1a847
    • Martin Blumenstingl's avatar
      net: phy: icplus: implement .did_interrupt for IP101A/G · f7e290fb
      Martin Blumenstingl authored 
      The IP101A_G_IRQ_CONF_STATUS register has bits to detect which
interrupts have fired. Implement the .did_interrupt callback to let the
PHY core know whether the interrupt was for this specific PHY.

This is useful for debugging interrupt problems with 32-pin IP101GR PHYs
where the interrupt line is shared with the RX_ERR (receive error
status) signal. The default values are:
- RX_ERR is enabled by default (LOW means that there is no receive
  error)
- the PHY's interrupt line is configured "active low" by default

Without any additional changes there is a flood of interrupts if the
RX_ERR/INTR32 signal is configured in RX_ERR mode (which is the
default). Having a did_interrupt ensures that the PHY core returns
IRQ_NONE instead of endlessly triggering the PHY state machine.
Additionally the kernel will report this after a while:
  irq 28: nobody cared (try booting with the "irqpoll" option)
Signed-off-by: default avatarMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      f7e290fb
    • Martin Blumenstingl's avatar
      net: phy: icplus: rename IP101A_G_NO_IRQ to IP101A_G_IRQ_ALL_MASK · a872c388
      Martin Blumenstingl authored 
      The datasheet uses the name "All Mask" for this bit. Change the name of
our #define to be consistent with the datasheet. While here also replace
the tab between the #define and IP101A_G_IRQ_ALL_MASK with a space.
No functional changes.
Signed-off-by: default avatarMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      a872c388
    • Martin Blumenstingl's avatar
      net: phy: icplus: use the BIT macro where possible · ee336140
      Martin Blumenstingl authored 
      This makes the code consistent by using the BIT() macro instead of
manual bit-shifting for some of the fields. No functional changes.
Signed-off-by: default avatarMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      ee336140
    • Martin Blumenstingl's avatar
      net: phy: icplus: keep all ip101a_g functions together · 034289b2
      Martin Blumenstingl authored 
      This simply moves ip101a_g_config_init right above
ip101a_g_config_intr so all functions for the ICPlus IP101A/G PHYs are
grouped together.
No functional changes.
Signed-off-by: default avatarMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      034289b2
    • Martin Blumenstingl's avatar
      dt-bindings: net: phy: add bindings for the IC Plus Corp. IP101A/G PHYs · fdc13a9e
      Martin Blumenstingl authored 
      The IP101A and IP101G series both have various models. Depending on the
board implementation we need a special property for the IP101GR (32-pin
LQFP package) PHY:
pin 21 ("RXER/INTR_32") outputs the "receive error" signal by default
(LOW means "normal operation", HIGH means that there's either a decoding
error of the received signal or that the PHY is receiving LPI). This pin
can also be switched to INTR32 mode, where the interrupt signal is
routed to this pin. The other PHYs don't need this special handling
because they have more pins available so the interrupt function gets a
dedicated pin.

This adds two properties to either select the "receive error" or
"interrupt" function of pin 21. Not specifying any function means that
the default set by the bootloader is used. This is required because the
IP101GR cannot be differentiated between other IP101 PHYs as the PHY
identification registers on all of these is 0x02430c54.

The IP101G (sold as die only, without package) may suffer from the same
issue depending on how it's integrated into a multi chip package by
another manufacturer. If only the RXER/INTR_32 pin is routed then the
users of the die-only variant may also have to explicitly configure the
mode of hte RXER/INTR_32 pin. This is the reason why no "is-ip101gr"
property was added. I have no evidence though which would confirm this
theory - so the binding itself is independent of that.
Signed-off-by: default avatarMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      fdc13a9e
    • Martin Blumenstingl's avatar
      dt-bindings: vendor-prefix: add prefix for IC Plus Corp. · 8a49f9db
      Martin Blumenstingl authored 
      IC Plus Corp. has various Ethernet related products such as Ethernet
transceivers, Ethernet controllers, Ethernet switches, etc.
Signed-off-by: default avatarMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      8a49f9db
  5. 18 Nov, 2018 19 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7