- 14 Oct, 2015 23 commits
-
-
Petr Cvek authored
This patch changes fast_mode settings for the normal and power I2C controller on the HTC Magician machine. Connected device on the Power I2C: - MAX1587A: working in the fast mode Connected devices on the Normal I2C: - UDA1380: working in the fast mode - OV9640: bus became stuck in the fast mode The OV9640 is not using a standard I2C protocol, but an SCCB variant. Maybe it is not fully compatible in the fast mode. Therefore fast mode for normal I2C is disabled. If you not using the OV9640 then you can enable the fast mode for the UDA1380. Signed-off-by: Petr Cvek <petr.cvek@tul.cz> [included Philipp Zabel's comment change] Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Petr Cvek authored
This patch fixes the charging detection functions for pda_power driver (according to newly discovered EGPIOs) and add NiCd backup accumulator charging support. Signed-off-by: Petr Cvek <petr.cvek@tul.cz> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Petr Cvek authored
Change the default Samsung LCD refresh from an unrealistic 117Hz to 50Hz as no video applications on the HTC Magician can work that fast. The optimalization lowers the RAM latency at least by 3%. Signed-off-by: Petr Cvek <petr.cvek@tul.cz> Acked-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Petr Cvek authored
This patch renames EGPIOs, which are used for the charging cable presence and type detection. Old names did not correspond with an observed functionality (on board_id 0x3a). The behavior is not: - AC charger - USB charger - Cable detection , but: - AC/USB type - Cable detection1 - Cable detection2 This patch fixes a possible typo in the bit offset for the cable detection EGPIO declaration, too. Signed-off-by: Petr Cvek <petr.cvek@tul.cz> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Petr Cvek authored
Delays for the Samsung LCD are greater than needed. These values were extracted from a datasheet. Signed-off-by: Petr Cvek <petr.cvek@tul.cz> Acked-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Petr Cvek authored
This patch renames GPIOs, which are used to control the power lines to the LCD screen. New names correspond to a real functionality, which was measured on the HTC Magician board_id 0x3a. Signed-off-by: Petr Cvek <petr.cvek@tul.cz> Acked-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Petr Cvek authored
This patch adds EGPIO pins: Infra transceiver power, NiCD charging and inserted charger cable. Signed-off-by: Petr Cvek <petr.cvek@tul.cz> Acked-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Petr Cvek authored
This patch changes the description of the LCD power GPIO to be more specific. Signed-off-by: Petr Cvek <petr.cvek@tul.cz> Acked-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Petr Cvek authored
Optimize the debug messages for the LCD power. Signed-off-by: Petr Cvek <petr.cvek@tul.cz> Acked-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Petr Cvek authored
Print more specific error message for global GPIOs. Signed-off-by: Petr Cvek <petr.cvek@tul.cz> Acked-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Petr Cvek authored
This patch fixes the indentation for the HTC Magician machine definition. Signed-off-by: Petr Cvek <petr.cvek@tul.cz> Acked-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Thierry Reding authored
Use a PWM lookup table to provide the PWM to the pwm-backlight device. The driver has a legacy code path that is required only because boards still use the legacy method of requesting PWMs by global ID. Replacing these usages allows that legacy fallback to be removed. Cc: Daniel Mack <daniel@zonque.org> Cc: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Thierry Reding authored
Use a PWM lookup table to provide the PWM to the pwm-backlight device. The driver has a legacy code path that is required only because boards still use the legacy method of requesting PWMs by global ID. Replacing these usages allows that legacy fallback to be removed. Cc: Daniel Mack <daniel@zonque.org> Cc: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Thierry Reding authored
Use a PWM lookup table to provide the PWM to the pwm-backlight device. The driver has a legacy code path that is required only because boards still use the legacy method of requesting PWMs by global ID. Replacing these usages allows that legacy fallback to be removed. Cc: Daniel Mack <daniel@zonque.org> Cc: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Thierry Reding authored
Use a PWM lookup table to provide the PWM to the pwm-backlight device. The driver has a legacy code path that is required only because boards still use the legacy method of requesting PWMs by global ID. Replacing these usages allows that legacy fallback to be removed. Cc: Daniel Mack <daniel@zonque.org> Cc: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Thierry Reding authored
Use a PWM lookup table to provide the PWM to the pwm-backlight device. The driver has a legacy code path that is required only because boards still use the legacy method of requesting PWMs by global ID. Replacing these usages allows that legacy fallback to be removed. Cc: Daniel Mack <daniel@zonque.org> Cc: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Thierry Reding authored
Use a PWM lookup table to provide the PWM to the pwm-backlight device. The driver has a legacy code path that is required only because boards still use the legacy method of requesting PWMs by global ID. Replacing these usages allows that legacy fallback to be removed. Cc: Daniel Mack <daniel@zonque.org> Cc: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Thierry Reding authored
Use a PWM lookup table to provide the PWM to the pwm-backlight device. The driver has a legacy code path that is required only because boards still use the legacy method of requesting PWMs by global ID. Replacing these usages allows that legacy fallback to be removed. Cc: Daniel Mack <daniel@zonque.org> Cc: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Thierry Reding authored
Use a PWM lookup table to provide the PWM to the pwm-backlight device. The driver has a legacy code path that is required only because boards still use the legacy method of requesting PWMs by global ID. Replacing these usages allows that legacy fallback to be removed. Cc: Daniel Mack <daniel@zonque.org> Cc: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Thierry Reding authored
Use a PWM lookup table to provide the PWM to the pwm-backlight device. The driver has a legacy code path that is required only because boards still use the legacy method of requesting PWMs by global ID. Replacing these usages allows that legacy fallback to be removed. Cc: Daniel Mack <daniel@zonque.org> Cc: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Thierry Reding authored
Use a PWM lookup table to provide the PWM to the pwm-backlight device. The driver has a legacy code path that is required only because boards still use the legacy method of requesting PWMs by global ID. Replacing these usages allows that legacy fallback to be removed. Cc: Daniel Mack <daniel@zonque.org> Cc: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Thierry Reding authored
Use a PWM lookup table to provide the PWM to the pwm-backlight device. The driver has a legacy code path that is required only because boards still use the legacy method of requesting PWMs by global ID. Replacing these usages allows that legacy fallback to be removed. Cc: Daniel Mack <daniel@zonque.org> Cc: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Thierry Reding authored
Use a PWM lookup table to provide the PWM to the pwm-backlight device. The driver has a legacy code path that is required only because boards still use the legacy method of requesting PWMs by global ID. Replacing these usages allows that legacy fallback to be removed. Cc: Daniel Mack <daniel@zonque.org> Cc: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> [ split pwm_remove_table() call on 2 lines ] Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
- 06 Oct, 2015 3 commits
-
-
Thierry Reding authored
Use a PWM lookup table to provide the PWM to the pwm-backlight device. The driver has a legacy code path that is required only because boards still use the legacy method of requesting PWMs by global ID. Replacing these usages allows that legacy fallback to be removed. Cc: Daniel Mack <daniel@zonque.org> Cc: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Acked-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Thierry Reding authored
Use a PWM lookup table to provide the PWM to the pwm-backlight device. The driver has a legacy code path that is required only because boards still use the legacy method of requesting PWMs by global ID. Replacing these usages allows that legacy fallback to be removed. Cc: Daniel Mack <daniel@zonque.org> Cc: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Thierry Reding authored
The ID and period for the backlight PWM are obtained from a PWM lookup table, so the corresponding values don't need to be duplicated into the platform data. Cc: Daniel Mack <daniel@zonque.org> Cc: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Acked-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
- 05 Oct, 2015 2 commits
-
-
Thierry Reding authored
Use a PWM lookup table to provide the PWM to the pwm-backlight device. The driver has a legacy code path that is required only because boards still use the legacy method of requesting PWMs by global ID. Replacing these usages allows that legacy fallback to be removed. Cc: Daniel Mack <daniel@zonque.org> Cc: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Thierry Reding authored
Use a PWM lookup table to provide the PWM to the pwm-backlight device. The driver has a legacy code path that is required only because boards still use the legacy method of requesting PWMs by global ID. Replacing these usages allows that legacy fallback to be removed. Cc: Daniel Mack <daniel@zonque.org> Cc: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
- 26 Sep, 2015 2 commits
-
-
Robert Jarzmik authored
The mioa701 is using the wm9713 for audio, battery and touchscreen. Add the missing audio part, which disappeared. Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
Robert Jarzmik authored
Add io memory and dma requestor lines to the irda pxa device. This is part of the conversion of pxaficp_ir to dmaengine, and to shrink its adherence to 'mach' includes. Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Tested-by: Petr Cvek <petr.cvek@tul.cz>
-
- 20 Sep, 2015 1 commit
-
-
Jarkko Nikula authored
Use for struct pxa2xx_spi_master clock_enable field was removed years ago from the pxa2xx-spi driver by the commit 2f1a74e5 ("[ARM] pxa: make pxa2xx_spi driver use ssp_request()/ssp_free()"). Therefore remove it from structure definition, documentation and from couple affected board files. Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Mark Brown <broonie@kernel.org> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
-
- 12 Sep, 2015 9 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/jesper/crisLinus Torvalds authored
Pull CRIS updates from Jesper Nilsson: "Mostly removal of old cruft of which we can use a generic version, or fixes for code not commonly run in the cris port, but also additions to enable some good debug" * tag 'cris-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris: (25 commits) CRISv10: delete unused lib/dmacopy.c CRISv10: delete unused lib/old_checksum.c CRIS: fix switch_mm() lockdep splat CRISv32: enable LOCKDEP_SUPPORT CRIS: add STACKTRACE_SUPPORT CRISv32: annotate irq enable in idle loop CRISv32: add support for irqflags tracing CRIS: UAPI: use generic types.h CRIS: UAPI: use generic shmbuf.h CRIS: UAPI: use generic msgbuf.h CRIS: UAPI: use generic socket.h CRIS: UAPI: use generic sembuf.h CRIS: UAPI: use generic sockios.h CRIS: UAPI: use generic auxvec.h CRIS: UAPI: use generic headers via Kbuild CRIS: UAPI: fix elf.h export CRIS: don't make asm/elf.h depend on asm/user.h CRIS: UAPI: fix ptrace.h CRISv32: Squash compile warnings for axisflashmap CRISv32: Add GPIO driver to the default configs ...
-
Linus Torvalds authored
rq_data_dir() returns either READ or WRITE (0 == READ, 1 == WRITE), not a boolean value. Now, admittedly the "!= 0" doesn't really change the value (0 stays as zero, 1 stays as one), but it's not only redundant, it confuses gcc, and causes gcc to warn about the construct switch (rq_data_dir(req)) { case READ: ... case WRITE: ... that we have in a few drivers. Now, the gcc warning is silly and stupid (it seems to warn not about the switch value having a different type from the case statements, but about _any_ boolean switch value), but in this case the code itself is silly and stupid too, so let's just change it, and get rid of warnings like this: drivers/block/hd.c: In function ‘hd_request’: drivers/block/hd.c:630:11: warning: switch condition has boolean value [-Wswitch-bool] switch (rq_data_dir(req)) { The odd '!= 0' came in when "cmd_flags" got turned into a "u64" in commit 5953316d ("block: make rq->cmd_flags be 64-bit") and is presumably because the old code (that just did a logical 'and' with 1) would then end up making the type of rq_data_dir() be u64 too. But if we want to retain the old regular integer type, let's just cast the result to 'int' rather than use that rather odd '!= 0'. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Linus Torvalds authored
Fix up the writeback plugging introduced in commit d353d758 ("writeback: plug writeback at a high level") that then caused problems due to the unplug happening with a spinlock held. * writeback-plugging: writeback: plug writeback in wb_writeback() and writeback_inodes_wb() Revert "writeback: plug writeback at a high level"
-
Linus Torvalds authored
We had to revert the pluggin in writeback_sb_inodes() because the wb->list_lock is held, but we could easily plug at a higher level before taking that lock, and unplug after releasing it. This does that. Chris will run performance numbers, just to verify that this approach is comparable to the alternative (we could just drop and re-take the lock around the blk_finish_plug() rather than these two commits. I'd have preferred waiting for actual performance numbers before picking one approach over the other, but I don't want to release rc1 with the known "sleeping function called from invalid context" issue, so I'll pick this cleanup version for now. But if the numbers show that we really want to plug just at the writeback_sb_inodes() level, and we should just play ugly games with the spinlock, we'll switch to that. Cc: Chris Mason <clm@fb.com> Cc: Josef Bacik <jbacik@fb.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Neil Brown <neilb@suse.de> Cc: Jan Kara <jack@suse.cz> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Linus Torvalds authored
I didn't notice this when merging the thermal code from Zhang, but his merge (commit 5a924a07: "Merge branches 'thermal-core' and 'thermal-intel' of .git into next") of the thermal-core and thermal-intel branches was wrong. In thermal-core, commit 17e8351a ("thermal: consistently use int for temperatures") converted the thermal layer to use "int" for temperatures. But in parallel, in the thermal-intel branch commit d0a12625 ("thermal: Add Intel PCH thermal driver") added support for the intel PCH thermal sensor using the old interfaces that used "unsigned long" pointers. This resulted in warnings like this: drivers/thermal/intel_pch_thermal.c:184:14: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types] .get_temp = pch_thermal_get_temp, ^ drivers/thermal/intel_pch_thermal.c:184:14: note: (near initialization for ‘tzd_ops.get_temp’) drivers/thermal/intel_pch_thermal.c:186:19: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types] .get_trip_temp = pch_get_trip_temp, ^ drivers/thermal/intel_pch_thermal.c:186:19: note: (near initialization for ‘tzd_ops.get_trip_temp’) This fixes it. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Linus Torvalds authored
Merge fourth patch-bomb from Andrew Morton: - sys_membarier syscall - seq_file interface changes - a few misc fixups * emailed patches from Andrew Morton <akpm@linux-foundation.org>: revert "ocfs2/dlm: use list_for_each_entry instead of list_for_each" mm/early_ioremap: add explicit #include of asm/early_ioremap.h fs/seq_file: convert int seq_vprint/seq_printf/etc... returns to void selftests: enhance membarrier syscall test selftests: add membarrier syscall test sys_membarrier(): system-wide memory barrier (generic, x86) MODSIGN: fix a compilation warning in extract-cert
-
Vineet Gupta authored
Newer bitfiles needs the reduced clk even for SMP builds Cc: <stable@vger.kernel.org> #4.2 Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://github.com/jonmason/ntbLinus Torvalds authored
Pull NTB fixes from Jon Mason: "NTB bug and documentation fixes, new device IDs, performance improvements, and adding a mailing list to MAINTAINERS for NTB" * tag 'ntb-4.3' of git://github.com/jonmason/ntb: NTB: Fix range check on memory window index NTB: Improve index handling in B2B MW workaround NTB: Fix documentation for ntb_peer_db_clear. NTB: Fix documentation for ntb_link_is_up NTB: Use unique DMA channels for TX and RX NTB: Remove dma_sync_wait from ntb_async_rx NTB: Clean up QP stats info NTB: Make the transport list in order of discovery NTB: Add PCI Device IDs for Broadwell Xeon NTB: Add flow control to the ntb_netdev NTB: Add list to MAINTAINERS
-