The first cluster group descriptor is not stored at the start of the
group but at an offset from the start.  We need to take this into
account while doing fstrim on the first cluster group.  Otherwise we
will wrongly start fstrim a few blocks after the desired start block and
the range can cross over into the next cluster group and zero out the
group descriptor there.  This can cause filesytem corruption that cannot
be fixed by fsck.

Link: http://lkml.kernel.org/r/1507835579-7308-1-git-send-email-ashish.samant@oracle.comSigned-off-by: Ashish Samant <ashish.samant@oracle.com>
Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Joseph Qi <jiangqi903@gmail.com>
Cc: Mark Fasheh <mfasheh@versity.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When the pagetable is walked in the implementation of /proc/<pid>/pagemap,
pmd_soft_dirty() is used for both the PMD huge page map and the PMD
migration entries.  That is wrong, pmd_swp_soft_dirty() should be used
for the PMD migration entries instead because the different page table
entry flag is used.

As a result, /proc/pid/pagemap may report incorrect soft dirty information
for PMD migration entries.

Link: http://lkml.kernel.org/r/20171017081818.31795-1-ying.huang@intel.com
Fixes: 84c3fc4e ("mm: thp: check pmd migration entry in common path")
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Cc: Daniel Colascione <dancol@google.com>
Cc: Zi Yan <zi.yan@cs.rutgers.edu>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This oops:

  kernel BUG at fs/hugetlbfs/inode.c:484!
  RIP: remove_inode_hugepages+0x3d0/0x410
  Call Trace:
    hugetlbfs_setattr+0xd9/0x130
    notify_change+0x292/0x410
    do_truncate+0x65/0xa0
    do_sys_ftruncate.constprop.3+0x11a/0x180
    SyS_ftruncate+0xe/0x10
    tracesys+0xd9/0xde

was caused by the lack of i_size check in hugetlb_mcopy_atomic_pte.

mmap() can still succeed beyond the end of the i_size after vmtruncate
zapped vmas in those ranges, but the faults must not succeed, and that
includes UFFDIO_COPY.

We could differentiate the retval to userland to represent a SIGBUS like
a page fault would do (vs SIGSEGV), but it doesn't seem very useful and
we'd need to pick a random retval as there's no meaningful syscall
retval that would differentiate from SIGSEGV and SIGBUS, there's just
-EFAULT.

Link: http://lkml.kernel.org/r/20171016223914.2421-2-aarcange@redhat.comSigned-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

For some odd historical reason, we preprocessed the linker scripts with
"-C", which keeps comments around.  That makes no sense, since the
comments are not meaningful for the build anyway.

And it actually breaks things, since linker scripts can't have C++ style
"//" comments in them, so keeping comments after preprocessing now
limits us in odd and surprising ways in our header files for no good
reason.

The -C option goes back to pre-git and pre-bitkeeper times, but seems to
have been historically used (along with "-traditional") for some
odd-ball architectures (ia64, MIPS and SH).  It probably didn't matter
back then either, but might possibly have been used to minimize the
difference between the original file and the pre-processed result.

The reason for this may be lost in time, but let's not perpetuate it
only because we can't remember why we did this crazy thing.

This was triggered by the recent addition of SPDX lines to the source
tree, where people apparently were confused about why header files
couldn't use the C++ comment format.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This reverts commit 51204e06.

There wasn't really any good reason for it, and people are complaining
(rightly) that it broke existing practice.

Cc: Len Brown <len.brown@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull arm64 fix from Catalin Marinas:
 "Check addr_limit in arm64 __dump_instr()"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: ensure __dump_instr() checks addr_limit

It's possible for a user to deliberately trigger __dump_instr with a
chosen kernel address.

Let's avoid problems resulting from this by using get_user() rather than
__get_user(), ensuring that we don't erroneously access kernel memory.

Where we use __dump_instr() on kernel text, we already switch to
KERNEL_DS, so this shouldn't adversely affect those cases.

Fixes: 60ffc30d ("arm64: Exception handling")
Cc: stable@vger.kernel.org
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull initial SPDX identifiers from Greg KH:
 "License cleanup: add SPDX license identifiers to some files

  Many source files in the tree are missing licensing information, which
  makes it harder for compliance tools to determine the correct license.

  By default all files without license information are under the default
  license of the kernel, which is GPL version 2.

  Update the files which contain no license information with the
  'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
  binding shorthand, which can be used instead of the full boiler plate
  text.

  This patch is based on work done by Thomas Gleixner and Kate Stewart
  and Philippe Ombredanne.

  How this work was done:

  Patches were generated and checked against linux-4.14-rc6 for a subset
  of the use cases:

   - file had no licensing information it it.

   - file was a */uapi/* one with no licensing information in it,

   - file was a */uapi/* one with existing licensing information,

  Further patches will be generated in subsequent months to fix up cases
  where non-standard license headers were used, and references to
  license had to be inferred by heuristics based on keywords.

  The analysis to determine which SPDX License Identifier to be applied
  to a file was done in a spreadsheet of side by side results from of
  the output of two independent scanners (ScanCode & Windriver)
  producing SPDX tag:value files created by Philippe Ombredanne.
  Philippe prepared the base worksheet, and did an initial spot review
  of a few 1000 files.

  The 4.13 kernel was the starting point of the analysis with 60,537
  files assessed. Kate Stewart did a file by file comparison of the
  scanner results in the spreadsheet to determine which SPDX license
  identifier(s) to be applied to the file. She confirmed any
  determination that was not immediately clear with lawyers working with
  the Linux Foundation.

  Criteria used to select files for SPDX license identifier tagging was:

   - Files considered eligible had to be source code files.

   - Make and config files were included as candidates if they contained
     >5 lines of source

   - File already had some variant of a license header in it (even if <5
     lines).

  All documentation files were explicitly excluded.

  The following heuristics were used to determine which SPDX license
  identifiers to apply.

   - when both scanners couldn't find any license traces, file was
     considered to have no license information in it, and the top level
     COPYING file license applied.

     For non */uapi/* files that summary was:

       SPDX license identifier                            # files
       ---------------------------------------------------|-------
       GPL-2.0                                              11139

     and resulted in the first patch in this series.

     If that file was a */uapi/* path one, it was "GPL-2.0 WITH
     Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
     was:

       SPDX license identifier                            # files
       ---------------------------------------------------|-------
       GPL-2.0 WITH Linux-syscall-note                        930

     and resulted in the second patch in this series.

   - if a file had some form of licensing information in it, and was one
     of the */uapi/* ones, it was denoted with the Linux-syscall-note if
     any GPL family license was found in the file or had no licensing in
     it (per prior point). Results summary:

       SPDX license identifier                            # files
       ---------------------------------------------------|------
       GPL-2.0 WITH Linux-syscall-note                       270
       GPL-2.0+ WITH Linux-syscall-note                      169
       ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
       ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
       LGPL-2.1+ WITH Linux-syscall-note                      15
       GPL-1.0+ WITH Linux-syscall-note                       14
       ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
       LGPL-2.0+ WITH Linux-syscall-note                       4
       LGPL-2.1 WITH Linux-syscall-note                        3
       ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
       ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

     and that resulted in the third patch in this series.

   - when the two scanners agreed on the detected license(s), that
     became the concluded license(s).

   - when there was disagreement between the two scanners (one detected
     a license but the other didn't, or they both detected different
     licenses) a manual inspection of the file occurred.

   - In most cases a manual inspection of the information in the file
     resulted in a clear resolution of the license that should apply
     (and which scanner probably needed to revisit its heuristics).

   - When it was not immediately clear, the license identifier was
     confirmed with lawyers working with the Linux Foundation.

   - If there was any question as to the appropriate license identifier,
     the file was flagged for further research and to be revisited later
     in time.

  In total, over 70 hours of logged manual review was done on the
  spreadsheet to determine the SPDX license identifiers to apply to the
  source files by Kate, Philippe, Thomas and, in some cases,
  confirmation by lawyers working with the Linux Foundation.

  Kate also obtained a third independent scan of the 4.13 code base from
  FOSSology, and compared selected files where the other two scanners
  disagreed against that SPDX file, to see if there was new insights.
  The Windriver scanner is based on an older version of FOSSology in
  part, so they are related.

  Thomas did random spot checks in about 500 files from the spreadsheets
  for the uapi headers and agreed with SPDX license identifier in the
  files he inspected. For the non-uapi files Thomas did random spot
  checks in about 15000 files.

  In initial set of patches against 4.14-rc6, 3 files were found to have
  copy/paste license identifier errors, and have been fixed to reflect
  the correct identifier.

  Additionally Philippe spent 10 hours this week doing a detailed manual
  inspection and review of the 12,461 patched files from the initial
  patch version early this week with:

   - a full scancode scan run, collecting the matched texts, detected
     license ids and scores

   - reviewing anything where there was a license detected (about 500+
     files) to ensure that the applied SPDX license was correct

   - reviewing anything where there was no detection but the patch
     license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
     applied SPDX license was correct

  This produced a worksheet with 20 files needing minor correction. This
  worksheet was then exported into 3 different .csv files for the
  different types of files to be modified.

  These .csv files were then reviewed by Greg. Thomas wrote a script to
  parse the csv files and add the proper SPDX tag to the file, in the
  format that the file expected. This script was further refined by Greg
  based on the output to detect more types of files automatically and to
  distinguish between header and source .c files (which need different
  comment types.) Finally Greg ran the script using the .csv files to
  generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  License cleanup: add SPDX license identifier to uapi header files with a license
  License cleanup: add SPDX license identifier to uapi header files with no license
  License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Merge tag 'linux-kselftest-4.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull kselftest fix from Shuah Khan:
 "This consists of a single fix to a regression to printing individual
  test results to the console. An earlier commit changed it to printing
  just the summary of results, which will negatively impact users that
  rely on console log to look at the individual test failures.

  This fix makes it optional to print summary and by default results get
  printed to the console"

* tag 'linux-kselftest-4.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests: lib.mk: print individual test results to console by default

Pull sound fixes from Takashi Iwai:
 "Unfortunately we still have received a significant amount of changes
  at the late stage, but at least all are small and clear fixes.

  There are two fixes for ALSA core stuff, yet another timer race fix
  and sequencer lockdep annotation fix. Both are spotted by syzkaller,
  and not too serious but better to paper over quickly.

  All other commits are about ASoC drivers, most notably, a revert of
  RT5514 hotword control that was included in 4.14-rc (due to a kind of
  abuse of kctl TLV ABI), together with topology API fixes and other
  device-specific small fixes that should go for stable, too"

* tag 'sound-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: seq: Fix nested rwsem annotation for lockdep splat
  ALSA: timer: Add missing mutex lock for compat ioctls
  ASoC: rt5616: fix 0x91 default value
  ASoC: rt5659: connect LOUT Amp with Charge Pump
  ASoC: rt5659: register power bit of LOUT Amp
  ASoC: rt5663: Change the dev getting function in rt5663_irq
  ASoC: rt5514: Revert Hotword Model control
  ASoC: topology: Fix a potential memory leak in 'soc_tplg_dapm_widget_denum_create()'
  ASoC: topology: Fix a potential NULL pointer dereference in 'soc_tplg_dapm_widget_denum_create()'
  ASoC: rt5514-spi: check irq status to schedule data copy
  ASoC: adau17x1: Workaround for noise bug in ADC

Merge branch 'fixes-v4.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security

Pull key handling fixes from James Morris:
 "Fixes for the Keys subsystem by Eric Biggers"

* 'fixes-v4.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  KEYS: fix out-of-bounds read during ASN.1 parsing
  KEYS: trusted: fix writing past end of buffer in trusted_read()
  KEYS: return full count in keyring_read() if buffer is too small

In commit 30d6e0a4 ("futex: Remove duplicated code and fix undefined
behaviour"), I let FUTEX_WAKE_OP to fail on invalid op.  Namely when op
should be considered as shift and the shift is out of range (< 0 or > 31).

But strace's test suite does this madness:

  futex(0x7fabd78bcffc, 0x5, 0xfacefeed, 0xb, 0x7fabd78bcffc, 0xa0caffee);
  futex(0x7fabd78bcffc, 0x5, 0xfacefeed, 0xb, 0x7fabd78bcffc, 0xbadfaced);
  futex(0x7fabd78bcffc, 0x5, 0xfacefeed, 0xb, 0x7fabd78bcffc, 0xffffffff);

When I pick the first 0xa0caffee, it decodes as:

  0x80000000 & 0xa0caffee: oparg is shift
  0x70000000 & 0xa0caffee: op is FUTEX_OP_OR
  0x0f000000 & 0xa0caffee: cmp is FUTEX_OP_CMP_EQ
  0x00fff000 & 0xa0caffee: oparg is sign-extended 0xcaf = -849
  0x00000fff & 0xa0caffee: cmparg is sign-extended 0xfee = -18

That means the op tries to do this:

  (futex |= (1 << (-849))) == -18

which is completely bogus. The new check of op in the code is:

        if (encoded_op & (FUTEX_OP_OPARG_SHIFT << 28)) {
                if (oparg < 0 || oparg > 31)
                        return -EINVAL;
                oparg = 1 << oparg;
        }

which results obviously in the "Invalid argument" errno:

  FAIL: futex
  ===========

  futex(0x7fabd78bcffc, 0x5, 0xfacefeed, 0xb, 0x7fabd78bcffc, 0xa0caffee) = -1: Invalid argument
  futex.test: failed test: ../futex failed with code 1

So let us soften the failure to print only a (ratelimited) message, crop
the value and continue as if it were right.  When userspace keeps up, we
can switch this to return -EINVAL again.

[v2] Do not return 0 immediatelly, proceed with the cropped value.

Fixes: 30d6e0a4 ("futex: Remove duplicated code and fix undefined behaviour")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <dvhart@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Many user space API headers have licensing information, which is either
incomplete, badly formatted or just a shorthand for referring to the
license under which the file is supposed to be.  This makes it hard for
compliance tools to determine the correct license.

Update these files with an SPDX license identifier.  The identifier was
chosen based on the license information in the file.

GPL/LGPL licensed headers get the matching GPL/LGPL SPDX license
identifier with the added 'WITH Linux-syscall-note' exception, which is
the officially assigned exception identifier for the kernel syscall
exception:

   NOTE! This copyright does *not* cover user programs that use kernel
   services by normal system calls - this is merely considered normal use
   of the kernel, and does *not* fall under the heading of "derived work".

This exception makes it possible to include GPL headers into non GPL
code, without confusing license compliance tools.

Headers which have either explicit dual licensing or are just licensed
under a non GPL license are updated with the corresponding SPDX
identifier and the GPLv2 with syscall exception identifier.  The format
is:
        ((GPL-2.0 WITH Linux-syscall-note) OR SPDX-ID-OF-OTHER-LICENSE)

SPDX license identifiers are a legally binding shorthand, which can be
used instead of the full boiler plate text.  The update does not remove
existing license information as this has to be done on a case by case
basis and the copyright holders might have to be consulted. This will
happen in a separate step.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.  See the previous patch in this series for the
methodology of how this patch was researched.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Many user space API headers are missing licensing information, which
makes it hard for compliance tools to determine the correct license.

By default are files without license information under the default
license of the kernel, which is GPLV2.  Marking them GPLV2 would exclude
them from being included in non GPLV2 code, which is obviously not
intended. The user space API headers fall under the syscall exception
which is in the kernels COPYING file:

   NOTE! This copyright does *not* cover user programs that use kernel
   services by normal system calls - this is merely considered normal use
   of the kernel, and does *not* fall under the heading of "derived work".

otherwise syscall usage would not be possible.

Update the files which contain no license information with an SPDX
license identifier.  The chosen identifier is 'GPL-2.0 WITH
Linux-syscall-note' which is the officially assigned identifier for the
Linux syscall exception.  SPDX license identifiers are a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.  See the previous patch in this series for the
methodology of how this patch was researched.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

syzkaller with KASAN reported an out-of-bounds read in
asn1_ber_decoder().  It can be reproduced by the following command,
assuming CONFIG_X509_CERTIFICATE_PARSER=y and CONFIG_KASAN=y:

    keyctl add asymmetric desc $'\x30\x30' @s

The bug is that the length of an ASN.1 data value isn't validated in the
case where it is encoded using the short form, causing the decoder to
read past the end of the input buffer.  Fix it by validating the length.

The bug report was:

    BUG: KASAN: slab-out-of-bounds in asn1_ber_decoder+0x10cb/0x1730 lib/asn1_decoder.c:233
    Read of size 1 at addr ffff88003cccfa02 by task syz-executor0/6818

    CPU: 1 PID: 6818 Comm: syz-executor0 Not tainted 4.14.0-rc7-00008-g5f479447 #2
    Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
    Call Trace:
     __dump_stack lib/dump_stack.c:16 [inline]
     dump_stack+0xb3/0x10b lib/dump_stack.c:52
     print_address_description+0x79/0x2a0 mm/kasan/report.c:252
     kasan_report_error mm/kasan/report.c:351 [inline]
     kasan_report+0x236/0x340 mm/kasan/report.c:409
     __asan_report_load1_noabort+0x14/0x20 mm/kasan/report.c:427
     asn1_ber_decoder+0x10cb/0x1730 lib/asn1_decoder.c:233
     x509_cert_parse+0x1db/0x650 crypto/asymmetric_keys/x509_cert_parser.c:89
     x509_key_preparse+0x64/0x7a0 crypto/asymmetric_keys/x509_public_key.c:174
     asymmetric_key_preparse+0xcb/0x1a0 crypto/asymmetric_keys/asymmetric_type.c:388
     key_create_or_update+0x347/0xb20 security/keys/key.c:855
     SYSC_add_key security/keys/keyctl.c:122 [inline]
     SyS_add_key+0x1cd/0x340 security/keys/keyctl.c:62
     entry_SYSCALL_64_fastpath+0x1f/0xbe
    RIP: 0033:0x447c89
    RSP: 002b:00007fca7a5d3bd8 EFLAGS: 00000246 ORIG_RAX: 00000000000000f8
    RAX: ffffffffffffffda RBX: 00007fca7a5d46cc RCX: 0000000000447c89
    RDX: 0000000020006f4a RSI: 0000000020006000 RDI: 0000000020001ff5
    RBP: 0000000000000046 R08: fffffffffffffffd R09: 0000000000000000
    R10: 0000000000000002 R11: 0000000000000246 R12: 0000000000000000
    R13: 0000000000000000 R14: 00007fca7a5d49c0 R15: 00007fca7a5d4700

Fixes: 42d5ec27 ("X.509: Add an ASN.1 decoder")
Cc: <stable@vger.kernel.org> # v3.7+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>

When calling keyctl_read() on a key of type "trusted", if the
user-supplied buffer was too small, the kernel ignored the buffer length
and just wrote past the end of the buffer, potentially corrupting
userspace memory.  Fix it by instead returning the size required, as per
the documentation for keyctl_read().

We also don't even fill the buffer at all in this case, as this is
slightly easier to implement than doing a short read, and either
behavior appears to be permitted.  It also makes it match the behavior
of the "encrypted" key type.

Fixes: d00a1c72 ("keys: add new trusted key-type")
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Cc: <stable@vger.kernel.org> # v2.6.38+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>

Commit e645016a ("KEYS: fix writing past end of user-supplied buffer
in keyring_read()") made keyring_read() stop corrupting userspace memory
when the user-supplied buffer is too small.  However it also made the
return value in that case be the short buffer size rather than the size
required, yet keyctl_read() is actually documented to return the size
required.  Therefore, switch it over to the documented behavior.

Note that for now we continue to have it fill the short buffer, since it
did that before (pre-v3.13) and dump_key_tree_aux() in keyutils arguably
relies on it.

Fixes: e645016a ("KEYS: fix writing past end of user-supplied buffer in keyring_read()")
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>

Pull signal bugfix from Eric Biederman:
 "When making the generic support for SIGEMT conditional on the presence
  of SIGEMT I made a typo that causes it to fail to activate. It was
  noticed comparatively quickly but the bug report just made it to me
  today"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  signal: Fix name of SIGEMT in #if defined() check

Commit cc731525 ("signal: Remove kernel interal si_code magic")
added a check for SIGMET and NSIGEMT being defined. That SIGMET should
in fact be SIGEMT, with SIGEMT being defined in
arch/{alpha,mips,sparc}/include/uapi/asm/signal.h

This was actually pointed out by BenHutchings in a lwn.net comment
here https://lwn.net/Comments/734608/

Fixes: cc731525 ("signal: Remove kernel interal si_code magic")
Signed-off-by: Andrew Clayton <andrew@digital-domain.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>

Pull block fixes from Jens Axboe:
 "A few fixes that should go into this series:

   - Regression fix for ide-cd, ensuring that a request is fully
     initialized. From Hongxu.

   - Ditto fix for virtio_blk, from Bart.

   - NVMe fix from Keith, ensuring that we set the right block size on
     revalidation. If the block size changed, we'd be in trouble without
     it.

   - NVMe rdma fix from Sagi, fixing a potential hang while the
     controller is being removed"

* 'for-linus' of git://git.kernel.dk/linux-block:
  ide:ide-cd: fix kernel panic resulting from missing scsi_req_init
  nvme: Fix setting logical block format when revalidating
  virtio_blk: Fix an SG_IO regression
  nvme-rdma: fix possible hang when issuing commands during ctrl removal

Merge tag 'asoc-fix-v4.14-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v4.14

A bunch of fixes here, mostly device specific ones (the biggest one
being the revert of the hotword support for rt5514), with a couple of
core fixes for potential issues with corrupted or otherwise invalid
topology files.

Pull networking fixes from David Miller:

 1) Fix refcounting in xfrm_bundle_lookup() when using a dummy bundle,
    from Steffen Klassert.

 2) Fix crypto header handling in rx data frames in ath10k driver, from
    Vasanthakumar Thiagarajan.

 3) Fix use after free of qdisc when we defer tcp_chain_flush() to a
    workqueue. From Cong Wang.

 4) Fix double free in lapbether driver, from Pan Bian.

 5) Sanitize TUNSETSNDBUF values, from Craig Gallek.

 6) Fix refcounting when addrconf_permanent_addr() calls
    ipv6_del_addr(). From Eric Dumazet.

 7) Fix MTU probing bug in TCP that goes back to 2007, from Eric
    Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  tcp: fix tcp_mtu_probe() vs highest_sack
  ipv6: addrconf: increment ifp refcount before ipv6_del_addr()
  tun/tap: sanitize TUNSETSNDBUF input
  mlxsw: i2c: Fix buffer increment counter for write transaction
  mlxsw: reg: Add high and low temperature thresholds
  MAINTAINERS: Remove Yotam from mlxfw
  MAINTAINERS: Update Yotam's E-mail
  net: hns: set correct return value
  net: lapbether: fix double free
  bpf: remove SK_REDIRECT from UAPI
  net: phy: marvell: Only configure RGMII delays when using RGMII
  xfrm: Fix GSO for IPsec with GRE tunnel.
  tc-testing: fix arg to ip command: -s -> -n
  net_sched: remove tcf_block_put_deferred()
  l2tp: hold tunnel in pppol2tp_connect()
  Revert "ath10k: fix napi_poll budget overflow"
  ath10k: rebuild crypto header in rx data frames
  wcn36xx: Remove unnecessary rcu_read_unlock in wcn36xx_bss_info_changed
  xfrm: Clear sk_dst_cache when applying per-socket policy.
  xfrm: Fix xfrm_dst_cache memleak

Syzkaller with KASAN has reported a use-after-free of vma->vm_flags in
__do_page_fault() with the following reproducer:

  mmap(&(0x7f0000000000/0xfff000)=nil, 0xfff000, 0x3, 0x32, 0xffffffffffffffff, 0x0)
  mmap(&(0x7f0000011000/0x3000)=nil, 0x3000, 0x1, 0x32, 0xffffffffffffffff, 0x0)
  r0 = userfaultfd(0x0)
  ioctl$UFFDIO_API(r0, 0xc018aa3f, &(0x7f0000002000-0x18)={0xaa, 0x0, 0x0})
  ioctl$UFFDIO_REGISTER(r0, 0xc020aa00, &(0x7f0000019000)={{&(0x7f0000012000/0x2000)=nil, 0x2000}, 0x1, 0x0})
  r1 = gettid()
  syz_open_dev$evdev(&(0x7f0000013000-0x12)="2f6465762f696e7075742f6576656e742300", 0x0, 0x0)
  tkill(r1, 0x7)

The vma should be pinned by mmap_sem, but handle_userfault() might (in a
return to userspace scenario) release it and then acquire again, so when
we return to __do_page_fault() (with other result than VM_FAULT_RETRY),
the vma might be gone.

Specifically, per Andrea the scenario is
 "A return to userland to repeat the page fault later with a
  VM_FAULT_NOPAGE retval (potentially after handling any pending signal
  during the return to userland). The return to userland is identified
  whenever FAULT_FLAG_USER|FAULT_FLAG_KILLABLE are both set in
  vmf->flags"

However, since commit a3c4fb7c ("x86/mm: Fix fault error path using
unsafe vma pointer") there is a vma_pkey() read of vma->vm_flags after
that point, which can thus become use-after-free.  Fix this by moving
the read before calling handle_mm_fault().
Reported-by: syzbot <bot+6a5269ce759a7bb12754ed9622076dc93f65a1f6@syzkaller.appspotmail.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Suggested-by: Kirill A. Shutemov <kirill@shutemov.name>
Fixes: 3c4fb7c9c2e ("x86/mm: Fix fault error path using unsafe vma pointer")
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull cifs fix from Steve French:
 "smb3 file name too long fix"

* tag 'smb3-file-name-too-long-fix' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: check MaxPathNameComponentLength != 0 before using it

Since we split the scsi_request out of struct request, while the
standard prep_rq_fn builds 10 byte cmds, it missed to invoke
scsi_req_init() to initialize certain fields of a scsi_request
structure (.__cmd[], .cmd, .cmd_len and .sense_len but no other
members of struct scsi_request).

An example panic on virtual machines (qemu/virtualbox) to boot
from IDE cdrom:
...
[    8.754381] Call Trace:
[    8.755419]  blk_peek_request+0x182/0x2e0
[    8.755863]  blk_fetch_request+0x1c/0x40
[    8.756148]  ? ktime_get+0x40/0xa0
[    8.756385]  do_ide_request+0x37d/0x660
[    8.756704]  ? cfq_group_service_tree_add+0x98/0xc0
[    8.757011]  ? cfq_service_tree_add+0x1e5/0x2c0
[    8.757313]  ? ktime_get+0x40/0xa0
[    8.757544]  __blk_run_queue+0x3d/0x60
[    8.757837]  queue_unplugged+0x2f/0xc0
[    8.758088]  blk_flush_plug_list+0x1f4/0x240
[    8.758362]  blk_finish_plug+0x2c/0x40
...
[    8.770906] RIP: ide_cdrom_prep_fn+0x63/0x180 RSP: ffff92aec018bae8
[    8.772329] ---[ end trace 6408481e551a85c9 ]---
...

Fixes: 82ed4db4 ("block: split scsi_request out of struct request")
Signed-off-by: Hongxu Jia <hongxu.jia@windriver.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Merge remote-tracking branches 'asoc/fix/topology', 'asoc/fix/adau17x1', 'asoc/fix/rt5514', 'asoc/fix/rt5616', 'asoc/fix/rt5659' and 'asoc/fix/rt5663' into tmp

Based on SNMP values provided by Roman, Yuchung made the observation
that some crashes in tcp_sacktag_walk() might be caused by MTU probing.

Looking at tcp_mtu_probe(), I found that when a new skb was placed
in front of the write queue, we were not updating tcp highest sack.

If one skb is freed because all its content was copied to the new skb
(for MTU probing), then tp->highest_sack could point to a now freed skb.

Bad things would then happen, including infinite loops.

This patch renames tcp_highest_sack_combine() and uses it
from tcp_mtu_probe() to fix the bug.

Note that I also removed one test against tp->sacked_out,
since we want to replace tp->highest_sack regardless of whatever
condition, since keeping a stale pointer to freed skb is a recipe
for disaster.

Fixes: a47e5a98 ("[TCP]: Convert highest_sack to sk_buff to allow direct access")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Reported-by: Roman Gushchin <guro@fb.com>
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the (unlikely) event fixup_permanent_addr() returns a failure,
addrconf_permanent_addr() calls ipv6_del_addr() without the
mandatory call to in6_ifa_hold(), leading to a refcount error,
spotted by syzkaller :

WARNING: CPU: 1 PID: 3142 at lib/refcount.c:227 refcount_dec+0x4c/0x50
lib/refcount.c:227
Kernel panic - not syncing: panic_on_warn set ...

CPU: 1 PID: 3142 Comm: ip Not tainted 4.14.0-rc4-next-20171009+ #33
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:16 [inline]
 dump_stack+0x194/0x257 lib/dump_stack.c:52
 panic+0x1e4/0x41c kernel/panic.c:181
 __warn+0x1c4/0x1e0 kernel/panic.c:544
 report_bug+0x211/0x2d0 lib/bug.c:183
 fixup_bug+0x40/0x90 arch/x86/kernel/traps.c:178
 do_trap_no_signal arch/x86/kernel/traps.c:212 [inline]
 do_trap+0x260/0x390 arch/x86/kernel/traps.c:261
 do_error_trap+0x120/0x390 arch/x86/kernel/traps.c:298
 do_invalid_op+0x1b/0x20 arch/x86/kernel/traps.c:311
 invalid_op+0x18/0x20 arch/x86/entry/entry_64.S:905
RIP: 0010:refcount_dec+0x4c/0x50 lib/refcount.c:227
RSP: 0018:ffff8801ca49e680 EFLAGS: 00010286
RAX: 000000000000002c RBX: ffff8801d07cfcdc RCX: 0000000000000000
RDX: 000000000000002c RSI: 1ffff10039493c90 RDI: ffffed0039493cc4
RBP: ffff8801ca49e688 R08: ffff8801ca49dd70 R09: 0000000000000000
R10: ffff8801ca49df58 R11: 0000000000000000 R12: 1ffff10039493cd9
R13: ffff8801ca49e6e8 R14: ffff8801ca49e7e8 R15: ffff8801d07cfcdc
 __in6_ifa_put include/net/addrconf.h:369 [inline]
 ipv6_del_addr+0x42b/0xb60 net/ipv6/addrconf.c:1208
 addrconf_permanent_addr net/ipv6/addrconf.c:3327 [inline]
 addrconf_notify+0x1c66/0x2190 net/ipv6/addrconf.c:3393
 notifier_call_chain+0x136/0x2c0 kernel/notifier.c:93
 __raw_notifier_call_chain kernel/notifier.c:394 [inline]
 raw_notifier_call_chain+0x2d/0x40 kernel/notifier.c:401
 call_netdevice_notifiers_info+0x32/0x60 net/core/dev.c:1697
 call_netdevice_notifiers net/core/dev.c:1715 [inline]
 __dev_notify_flags+0x15d/0x430 net/core/dev.c:6843
 dev_change_flags+0xf5/0x140 net/core/dev.c:6879
 do_setlink+0xa1b/0x38e0 net/core/rtnetlink.c:2113
 rtnl_newlink+0xf0d/0x1a40 net/core/rtnetlink.c:2661
 rtnetlink_rcv_msg+0x733/0x1090 net/core/rtnetlink.c:4301
 netlink_rcv_skb+0x216/0x440 net/netlink/af_netlink.c:2408
 rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:4313
 netlink_unicast_kernel net/netlink/af_netlink.c:1273 [inline]
 netlink_unicast+0x4e8/0x6f0 net/netlink/af_netlink.c:1299
 netlink_sendmsg+0xa4a/0xe70 net/netlink/af_netlink.c:1862
 sock_sendmsg_nosec net/socket.c:633 [inline]
 sock_sendmsg+0xca/0x110 net/socket.c:643
 ___sys_sendmsg+0x75b/0x8a0 net/socket.c:2049
 __sys_sendmsg+0xe5/0x210 net/socket.c:2083
 SYSC_sendmsg net/socket.c:2094 [inline]
 SyS_sendmsg+0x2d/0x50 net/socket.c:2090
 entry_SYSCALL_64_fastpath+0x1f/0xbe
RIP: 0033:0x7fa9174d3320
RSP: 002b:00007ffe302ae9e8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007ffe302b2ae0 RCX: 00007fa9174d3320
RDX: 0000000000000000 RSI: 00007ffe302aea20 RDI: 0000000000000016
RBP: 0000000000000082 R08: 0000000000000000 R09: 000000000000000f
R10: 0000000000000000 R11: 0000000000000246 R12: 00007ffe302b32a0
R13: 0000000000000000 R14: 00007ffe302b2ab8 R15: 00007ffe302b32b8

Fixes: f1705ec1 ("net: ipv6: Make address flushing on ifdown optional")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Ahern <dsahern@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Syzkaller found several variants of the lockup below by setting negative
values with the TUNSETSNDBUF ioctl.  This patch adds a sanity check
to both the tun and tap versions of this ioctl.

  watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [repro:2389]
  Modules linked in:
  irq event stamp: 329692056
  hardirqs last  enabled at (329692055): [<ffffffff824b8381>] _raw_spin_unlock_irqrestore+0x31/0x75
  hardirqs last disabled at (329692056): [<ffffffff824b9e58>] apic_timer_interrupt+0x98/0xb0
  softirqs last  enabled at (35659740): [<ffffffff824bc958>] __do_softirq+0x328/0x48c
  softirqs last disabled at (35659731): [<ffffffff811c796c>] irq_exit+0xbc/0xd0
  CPU: 0 PID: 2389 Comm: repro Not tainted 4.14.0-rc7 #23
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
  task: ffff880009452140 task.stack: ffff880006a20000
  RIP: 0010:_raw_spin_lock_irqsave+0x11/0x80
  RSP: 0018:ffff880006a27c50 EFLAGS: 00000282 ORIG_RAX: ffffffffffffff10
  RAX: ffff880009ac68d0 RBX: ffff880006a27ce0 RCX: 0000000000000000
  RDX: 0000000000000001 RSI: ffff880006a27ce0 RDI: ffff880009ac6900
  RBP: ffff880006a27c60 R08: 0000000000000000 R09: 0000000000000000
  R10: 0000000000000001 R11: 000000000063ff00 R12: ffff880009ac6900
  R13: ffff880006a27cf8 R14: 0000000000000001 R15: ffff880006a27cf8
  FS:  00007f4be4838700(0000) GS:ffff88000cc00000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000000020101000 CR3: 0000000009616000 CR4: 00000000000006f0
  Call Trace:
   prepare_to_wait+0x26/0xc0
   sock_alloc_send_pskb+0x14e/0x270
   ? remove_wait_queue+0x60/0x60
   tun_get_user+0x2cc/0x19d0
   ? __tun_get+0x60/0x1b0
   tun_chr_write_iter+0x57/0x86
   __vfs_write+0x156/0x1e0
   vfs_write+0xf7/0x230
   SyS_write+0x57/0xd0
   entry_SYSCALL_64_fastpath+0x1f/0xbe
  RIP: 0033:0x7f4be4356df9
  RSP: 002b:00007ffc18101c08 EFLAGS: 00000293 ORIG_RAX: 0000000000000001
  RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f4be4356df9
  RDX: 0000000000000046 RSI: 0000000020101000 RDI: 0000000000000005
  RBP: 00007ffc18101c40 R08: 0000000000000001 R09: 0000000000000001
  R10: 0000000000000001 R11: 0000000000000293 R12: 0000559c75f64780
  R13: 00007ffc18101d30 R14: 0000000000000000 R15: 0000000000000000

Fixes: 33dccbb0 ("tun: Limit amount of queued packets per device")
Fixes: 20d29d7a ("net: macvtap driver")
Signed-off-by: Craig Gallek <kraig@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It fixes a problem for the last chunk where 'chunk_size' is smaller than
MLXSW_I2C_BLK_MAX and data is copied to the wrong offset, overriding
previous data.

Fixes: 6882b0ae ("mlxsw: Introduce support for I2C bus")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net): ipsec 2017-11-01

1) Fix a memleak when a packet matches a policy
   without a matching state.

2) Reset the socket cached dst_entry when inserting
   a socket policy, otherwise the policy might be
   ignored. From Jonathan Basseri.

3) Fix GSO for a IPsec, GRE tunnel combination.
   We reset the encapsulation field at the skb
   too erly, as a result GRE does not segment
   GSO packets. Fix this by resetting the the
   encapsulation field right before the
   transformation where the inner headers get
   invalid.

Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The ASIC has the ability to generate events whenever a sensor indicates
the temperature goes above or below its high or low thresholds,
respectively.

In new firmware versions the firmware enforces a minimum of 5
degrees Celsius difference between both thresholds. Make the driver
conform to this requirement.

Note that this is required even when the events are disabled, as in
certain systems interrupts are generated via GPIO based on these
thresholds.

Fixes: 85926f87 ("mlxsw: reg: Add definition of temperature management registers")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Provide a mailing list for maintenance of the module instead.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For the time being I will be available in my private mail. Update both the
MAINTAINERS file and the individual modules MODULE_AUTHOR directive with
the new address.
Signed-off-by: Yotam Gigi <yotam.gi@gmail.com>
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function of_parse_phandle() returns a NULL pointer if it cannot
resolve a phandle property to a device_node pointer. In function
hns_nic_dev_probe(), its return value is passed to PTR_ERR to extract
the error code. However, in this case, the extracted error code will
always be zero, which is unexpected.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function netdev_priv() returns the private data of the device. The
memory to store the private data is allocated in alloc_netdev() and is
released in netdev_free(). Calling kfree() on the return value of
netdev_priv() after netdev_free() results in a double free bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that SK_REDIRECT is no longer a valid return code. Remove it
from the UAPI completely. Then do a namespace remapping internal
to sockmap so SK_REDIRECT is no longer externally visible.

Patchs primary change is to do a namechange from SK_REDIRECT to
__SK_REDIRECT
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The fix 5987feb3 ("net: phy: marvell: logical vs bitwise OR typo")
uncovered another bug in the Marvell PHY driver, which broke the
Marvell OpenRD platform. It relies on the bootloader configuring the
RGMII delays and does not specify a phy-mode in its device tree.  The
PHY driver should only configure RGMII delays if the phy mode
indicates it is using RGMII. Without anything in device tree, the
mv643xx Ethernet driver defaults to GMII.

Fixes: 5987feb3 ("net: phy: marvell: logical vs bitwise OR typo")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2017-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.14

The most important here is the security vulnerabitility fix for
ath10k.

ath10k

* fix security vulnerability with missing PN check on certain hardware

* revert ath10k napi fix as it caused regressions on QCA6174

wcn36xx

* remove unnecessary rcu_read_unlock() from error path
====================
Signed-off-by: David S. Miller <davem@davemloft.net>