This patch fixes a few newline issues and also
replaces p_err with p_info in prog.c

Fixes: b053b439 ("bpf: libbpf: bpftool: Print bpf_line_info during prog dump")
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Currently, the destination register is marked as unknown for 32-bit
sub-register move (BPF_MOV | BPF_ALU) whenever the source register type is
SCALAR_VALUE.

This is too conservative that some valid cases will be rejected.
Especially, this may turn a constant scalar value into unknown value that
could break some assumptions of verifier.

For example, test_l4lb_noinline.c has the following C code:

    struct real_definition *dst

1:  if (!get_packet_dst(&dst, &pckt, vip_info, is_ipv6))
2:    return TC_ACT_SHOT;
3:
4:  if (dst->flags & F_IPV6) {

get_packet_dst is responsible for initializing "dst" into valid pointer and
return true (1), otherwise return false (0). The compiled instruction
sequence using alu32 will be:

  412: (54) (u32) r7 &= (u32) 1
  413: (bc) (u32) r0 = (u32) r7
  414: (95) exit

insn 413, a BPF_MOV | BPF_ALU, however will turn r0 into unknown value even
r7 contains SCALAR_VALUE 1.

This causes trouble when verifier is walking the code path that hasn't
initialized "dst" inside get_packet_dst, for which case 0 is returned and
we would then expect verifier concluding line 1 in the above C code pass
the "if" check, therefore would skip fall through path starting at line 4.
Now, because r0 returned from callee has became unknown value, so verifier
won't skip analyzing path starting at line 4 and "dst->flags" requires
dereferencing the pointer "dst" which actually hasn't be initialized for
this path.

This patch relaxed the code marking sub-register move destination. For a
SCALAR_VALUE, it is safe to just copy the value from source then truncate
it into 32-bit.

A unit test also included to demonstrate this issue. This test will fail
before this patch.

This relaxation could let verifier skipping more paths for conditional
comparison against immediate. It also let verifier recording a more
accurate/strict value for one register at one state, if this state end up
with going through exit without rejection and it is used for state
comparison later, then it is possible an inaccurate/permissive value is
better. So the real impact on verifier processed insn number is complex.
But in all, without this fix, valid program could be rejected.

>From real benchmarking on kernel selftests and Cilium bpf tests, there is
no impact on processed instruction number when tests ares compiled with
default compilation options. There is slightly improvements when they are
compiled with -mattr=+alu32 after this patch.

Also, test_xdp_noinline/-mattr=+alu32 now passed verification. It is
rejected before this fix.

Insn processed before/after this patch:

                        default     -mattr=+alu32

Kernel selftest

===
test_xdp.o              371/371      369/369
test_l4lb.o             6345/6345    5623/5623
test_xdp_noinline.o     2971/2971    rejected/2727
test_tcp_estates.o      429/429      430/430

Cilium bpf
===
bpf_lb-DLB_L3.o:        2085/2085     1685/1687
bpf_lb-DLB_L4.o:        2287/2287     1986/1982
bpf_lb-DUNKNOWN.o:      690/690       622/622
bpf_lxc.o:              95033/95033   N/A
bpf_netdev.o:           7245/7245     N/A
bpf_overlay.o:          2898/2898     3085/2947

NOTE:
  - bpf_lxc.o and bpf_netdev.o compiled by -mattr=+alu32 are rejected by
    verifier due to another issue inside verifier on supporting alu32
    binary.
  - Each cilium bpf program could generate several processed insn number,
    above number is sum of them.

v1->v2:
 - Restrict the change on SCALAR_VALUE.
 - Update benchmark numbers on Cilium bpf tests.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Some IR remotes have a directional pad or other pointer-like thing that
can be used as a mouse. Make it possible to decode these types of IR
protocols in BPF.

Cc: netdev@vger.kernel.org
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Martin Lau says:

====================
This patch series introduces the bpf_line_info.  Please see individual patch
for details.

It will be useful for introspection purpose, like:

[root@arch-fb-vm1 bpf]# ~/devshare/fb-kernel/linux/tools/bpf/bpftool/bpftool prog dump jited pinned /sys/fs/bpf/test_btf_haskv
[...]
int test_long_fname_2(struct dummy_tracepoint_args * arg):
bpf_prog_44a040bf25481309_test_long_fname_2:
; static int test_long_fname_2(struct dummy_tracepoint_args *arg)
   0:   push   %rbp
   1:   mov    %rsp,%rbp
   4:   sub    $0x30,%rsp
   b:   sub    $0x28,%rbp
   f:   mov    %rbx,0x0(%rbp)
  13:   mov    %r13,0x8(%rbp)
  17:   mov    %r14,0x10(%rbp)
  1b:   mov    %r15,0x18(%rbp)
  1f:   xor    %eax,%eax
  21:   mov    %rax,0x20(%rbp)
  25:   xor    %esi,%esi
; int key = 0;
  27:   mov    %esi,-0x4(%rbp)
; if (!arg->sock)
  2a:   mov    0x8(%rdi),%rdi
; if (!arg->sock)
  2e:   cmp    $0x0,%rdi
  32:   je     0x0000000000000070
  34:   mov    %rbp,%rsi
; counts = bpf_map_lookup_elem(&btf_map, &key);
  37:   add    $0xfffffffffffffffc,%rsi
  3b:   movabs $0xffff8881139d7480,%rdi
  45:   add    $0x110,%rdi
  4c:   mov    0x0(%rsi),%eax
  4f:   cmp    $0x4,%rax
  53:   jae    0x000000000000005e
  55:   shl    $0x3,%rax
  59:   add    %rdi,%rax
  5c:   jmp    0x0000000000000060
  5e:   xor    %eax,%eax
; if (!counts)
  60:   cmp    $0x0,%rax
  64:   je     0x0000000000000070
; counts->v6++;
  66:   mov    0x4(%rax),%edi
  69:   add    $0x1,%rdi
  6d:   mov    %edi,0x4(%rax)
  70:   mov    0x0(%rbp),%rbx
  74:   mov    0x8(%rbp),%r13
  78:   mov    0x10(%rbp),%r14
  7c:   mov    0x18(%rbp),%r15
  80:   add    $0x28,%rbp
  84:   leaveq
  85:   retq
[...]
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

This patch adds print bpf_line_info function in 'prog dump jitted'
and 'prog dump xlated':

[root@arch-fb-vm1 bpf]# ~/devshare/fb-kernel/linux/tools/bpf/bpftool/bpftool prog dump jited pinned /sys/fs/bpf/test_btf_haskv
[...]
int test_long_fname_2(struct dummy_tracepoint_args * arg):
bpf_prog_44a040bf25481309_test_long_fname_2:
; static int test_long_fname_2(struct dummy_tracepoint_args *arg)
   0:	push   %rbp
   1:	mov    %rsp,%rbp
   4:	sub    $0x30,%rsp
   b:	sub    $0x28,%rbp
   f:	mov    %rbx,0x0(%rbp)
  13:	mov    %r13,0x8(%rbp)
  17:	mov    %r14,0x10(%rbp)
  1b:	mov    %r15,0x18(%rbp)
  1f:	xor    %eax,%eax
  21:	mov    %rax,0x20(%rbp)
  25:	xor    %esi,%esi
; int key = 0;
  27:	mov    %esi,-0x4(%rbp)
; if (!arg->sock)
  2a:	mov    0x8(%rdi),%rdi
; if (!arg->sock)
  2e:	cmp    $0x0,%rdi
  32:	je     0x0000000000000070
  34:	mov    %rbp,%rsi
; counts = bpf_map_lookup_elem(&btf_map, &key);
  37:	add    $0xfffffffffffffffc,%rsi
  3b:	movabs $0xffff8881139d7480,%rdi
  45:	add    $0x110,%rdi
  4c:	mov    0x0(%rsi),%eax
  4f:	cmp    $0x4,%rax
  53:	jae    0x000000000000005e
  55:	shl    $0x3,%rax
  59:	add    %rdi,%rax
  5c:	jmp    0x0000000000000060
  5e:	xor    %eax,%eax
; if (!counts)
  60:	cmp    $0x0,%rax
  64:	je     0x0000000000000070
; counts->v6++;
  66:	mov    0x4(%rax),%edi
  69:	add    $0x1,%rdi
  6d:	mov    %edi,0x4(%rax)
  70:	mov    0x0(%rbp),%rbx
  74:	mov    0x8(%rbp),%r13
  78:	mov    0x10(%rbp),%r14
  7c:	mov    0x18(%rbp),%r15
  80:	add    $0x28,%rbp
  84:	leaveq
  85:	retq
[...]

With linum:
[root@arch-fb-vm1 bpf]# ~/devshare/fb-kernel/linux/tools/bpf/bpftool/bpftool prog dump jited pinned /sys/fs/bpf/test_btf_haskv linum
int _dummy_tracepoint(struct dummy_tracepoint_args * arg):
bpf_prog_b07ccb89267cf242__dummy_tracepoint:
; return test_long_fname_1(arg); [file:/data/users/kafai/fb-kernel/linux/tools/testing/selftests/bpf/test_btf_haskv.c line_num:54 line_col:9]
   0:	push   %rbp
   1:	mov    %rsp,%rbp
   4:	sub    $0x28,%rsp
   b:	sub    $0x28,%rbp
   f:	mov    %rbx,0x0(%rbp)
  13:	mov    %r13,0x8(%rbp)
  17:	mov    %r14,0x10(%rbp)
  1b:	mov    %r15,0x18(%rbp)
  1f:	xor    %eax,%eax
  21:	mov    %rax,0x20(%rbp)
  25:	callq  0x000000000000851e
; return test_long_fname_1(arg); [file:/data/users/kafai/fb-kernel/linux/tools/testing/selftests/bpf/test_btf_haskv.c line_num:54 line_col:2]
  2a:	xor    %eax,%eax
  2c:	mov    0x0(%rbp),%rbx
  30:	mov    0x8(%rbp),%r13
  34:	mov    0x10(%rbp),%r14
  38:	mov    0x18(%rbp),%r15
  3c:	add    $0x28,%rbp
  40:	leaveq
  41:	retq
[...]
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

This patch adds bpf_line_info support to libbpf:
1) Parsing the line_info sec from ".BTF.ext"
2) Relocating the line_info.  If the main prog *_info relocation
   fails, it will ignore the remaining subprog line_info and continue.
   If the subprog *_info relocation fails, it will bail out.
3) BPF_PROG_LOAD a prog with line_info
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

This patch refactor and fix a bug in the libbpf's bpf_func_info loading
logic.  The bug fix and refactoring are targeting the same
commit 2993e051 ("tools/bpf: add support to read .BTF.ext sections")
which is in the bpf-next branch.

1) In bpf_load_program_xattr(), it should retry when errno == E2BIG
   regardless of log_buf and log_buf_sz.  This patch fixes it.

2) btf_ext__reloc_init() and btf_ext__reloc() are essentially
   the same except btf_ext__reloc_init() always has insns_cnt == 0.
   Hence, btf_ext__reloc_init() is removed.

   btf_ext__reloc() is also renamed to btf_ext__reloc_func_info()
   to get ready for the line_info support in the next patch.

3) Consolidate func_info section logic from "btf_ext_parse_hdr()",
   "btf_ext_validate_func_info()" and "btf_ext__new()" to
   a new function "btf_ext_copy_func_info()" such that similar
   logic can be reused by the later libbpf's line_info patch.

4) The next line_info patch will store line_info_cnt instead of
   line_info_len in the bpf_program because the kernel is taking
   line_info_cnt also.  It will save a few "len" to "cnt" conversions
   and will also save some function args.

   Hence, this patch also makes bpf_program to store func_info_cnt
   instead of func_info_len.

5) btf_ext depends on btf.  e.g. the func_info's type_id
   in ".BTF.ext" is not useful when ".BTF" is absent.
   This patch only init the obj->btf_ext pointer after
   it has successfully init the obj->btf pointer.

   This can avoid always checking "obj->btf && obj->btf_ext"
   together for accessing ".BTF.ext".  Checking "obj->btf_ext"
   alone will do.

6) Move "struct btf_sec_func_info" from btf.h to btf.c.
   There is no external usage outside btf.c.

Fixes: 2993e051 ("tools/bpf: add support to read .BTF.ext sections")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Add unit tests for bpf_line_info for both BPF_PROG_LOAD and
BPF_OBJ_GET_INFO_BY_FD.

jit enabled:
[root@arch-fb-vm1 bpf]# ./test_btf -k 0
BTF prog info raw test[5] (line_info (No subprog)): OK
BTF prog info raw test[6] (line_info (No subprog. insn_off >= prog->len)): OK
BTF prog info raw test[7] (line_info (No subprog. zero tailing line_info): OK
BTF prog info raw test[8] (line_info (No subprog. nonzero tailing line_info)): OK
BTF prog info raw test[9] (line_info (subprog)): OK
BTF prog info raw test[10] (line_info (subprog + func_info)): OK
BTF prog info raw test[11] (line_info (subprog. missing 1st func line info)): OK
BTF prog info raw test[12] (line_info (subprog. missing 2nd func line info)): OK
BTF prog info raw test[13] (line_info (subprog. unordered insn offset)): OK

jit disabled:
BTF prog info raw test[5] (line_info (No subprog)): not jited. skipping jited_line_info check. OK
BTF prog info raw test[6] (line_info (No subprog. insn_off >= prog->len)): OK
BTF prog info raw test[7] (line_info (No subprog. zero tailing line_info): not jited. skipping jited_line_info check. OK
BTF prog info raw test[8] (line_info (No subprog. nonzero tailing line_info)): OK
BTF prog info raw test[9] (line_info (subprog)): not jited. skipping jited_line_info check. OK
BTF prog info raw test[10] (line_info (subprog + func_info)): not jited. skipping jited_line_info check. OK
BTF prog info raw test[11] (line_info (subprog. missing 1st func line info)): OK
BTF prog info raw test[12] (line_info (subprog. missing 2nd func line info)): OK
BTF prog info raw test[13] (line_info (subprog. unordered insn offset)): OK
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

1) bpf_load_program_xattr() is absorbing the EBIG error
   which makes testing this case impossible.  It is replaced
   with a direct syscall(__NR_bpf, BPF_PROG_LOAD,...).
2) The test_func_type() is renamed to test_info_raw() to
   prepare for the new line_info test in the next patch.
3) The bpf_obj_get_info_by_fd() testing for func_info
   is refactored to test_get_finfo().  A new
   test_get_linfo() will be added in the next patch
   for testing line_info purpose.
4) The test->func_info_cnt is checked instead of
   a static value "2".
5) Remove unnecessary "\n" in error message.
6) Adding back info_raw_test_num to the cmd arg such
   that a specific test case can be tested, like
   all other existing tests.

7) Fix a bug in handling expected_prog_load_failure.
   A test could pass even if prog_fd != -1 while
   expected_prog_load_failure is true.
8) The min rec_size check should be < 8 instead of < 4.

Fixes: 4798c4ba ("tools/bpf: extends test_btf to test load/retrieve func_type info")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Sync uapi bpf.h to tools/include/uapi/linux for
the new bpf_line_info.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

This patch adds bpf_line_info support.

It accepts an array of bpf_line_info objects during BPF_PROG_LOAD.
The "line_info", "line_info_cnt" and "line_info_rec_size" are added
to the "union bpf_attr".  The "line_info_rec_size" makes
bpf_line_info extensible in the future.

The new "check_btf_line()" ensures the userspace line_info is valid
for the kernel to use.

When the verifier is translating/patching the bpf_prog (through
"bpf_patch_insn_single()"), the line_infos' insn_off is also
adjusted by the newly added "bpf_adj_linfo()".

If the bpf_prog is jited, this patch also provides the jited addrs (in
aux->jited_linfo) for the corresponding line_info.insn_off.
"bpf_prog_fill_jited_linfo()" is added to fill the aux->jited_linfo.
It is currently called by the x86 jit.  Other jits can also use
"bpf_prog_fill_jited_linfo()" and it will be done in the followup patches.
In the future, if it deemed necessary, a particular jit could also provide
its own "bpf_prog_fill_jited_linfo()" implementation.

A few "*line_info*" fields are added to the bpf_prog_info such
that the user can get the xlated line_info back (i.e. the line_info
with its insn_off reflecting the translated prog).  The jited_line_info
is available if the prog is jited.  It is an array of __u64.
If the prog is not jited, jited_line_info_cnt is 0.

The verifier's verbose log with line_info will be done in
a follow up patch.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Jiong Wang says:

====================
BPF_ALU | BPF_ARSH | BPF_* were rejected by commit: 7891a87e
("bpf: arsh is not supported in 32 bit alu thus reject it"). As explained
in the commit message, this is due to there is no complete support for them
on interpreter and various JIT compilation back-ends.

This patch set is a follow-up which completes the missing bits. This also
pave the way for running bpf program compiled with ALU32 instruction
enabled by specifing -mattr=+alu32 to LLVM for which case there is likely
to have more BPF_ALU | BPF_ARSH insns that will trigger the rejection code.

test_verifier.c is updated accordingly.

I have tested this patch set on x86-64 and NFP, I need help of review and
test on the arch changes (mips/ppc/s390).

Note, there might be merge confict on mips change which is better to be
applied on top of:

  commit: 20b880a05f06 ("mips: bpf: fix encoding bug for mm_srlv32_op"),

which is on mips-fixes branch at the moment.

Thanks.

v1->v2:
 - Fix ppc implementation bug. Should zero high bits explicitly.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

"arsh32 on imm" and "arsh32 on reg" now are accepted. Also added two new
testcases to make sure arsh32 won't be treated as arsh64 during
interpretation or JIT code-gen for which case the high bits will be moved
into low halve that the testcases could catch them.
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

This patch remove the rejection on BPF_ALU | BPF_ARSH as we have supported
them on interpreter and all JIT back-ends
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

This patch implements interpreting BPF_ALU | BPF_ARSH. Do arithmetic right
shift on low 32-bit sub-register, and zero the high 32 bits.
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

BPF_X support needs indirect shift mode, please see code comments for
details.
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

This patch implements code-gen for BPF_ALU | BPF_ARSH | BPF_*.

Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

This patch implements code-gen for BPF_ALU | BPF_ARSH | BPF_*.

Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com>
Cc: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Jitting of BPF_K is supported already, but not BPF_X. This patch complete
the support for the latter on both MIPS and microMIPS.

Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

For micro-mips, srlv inside POOL32A encoding space should use 0x50
sub-opcode, NOT 0x90.

Some early version ISA doc describes the encoding as 0x90 for both srlv and
srav, this looks to me was a typo. I checked Binutils libopcode
implementation which is using 0x50 for srlv and 0x90 for srav.

v1->v2:
  - Keep mm_srlv32_op sorted by value.

Fixes: f31318fd ("MIPS: uasm: Add srlv uasm instruction")
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Martin KaFai Lau says:

====================
The patchset has a few improvements on bpf_func_info:
1. Improvements on the behaviors of info.func_info, info.func_info_cnt
   and info.func_info_rec_size.
2. Name change: s/insn_offset/insn_off/

Please see individual patch for details.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Similar to info.jited_*, info.func_info could be 0 if
bpf_dump_raw_ok() == false.

This patch makes changes to test_btf and bpftool to expect info.func_info
could be 0.

This patch also makes the needed changes for s/insn_offset/insn_off/.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

This patch sync the name changes in bpf_func_info to
the tools/.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

The later patch will introduce "struct bpf_line_info" which
has member "line_off" and "file_off" referring back to the
string section in btf.  The line_"off" and file_"off"
are more consistent to the naming convention in btf.h that
means "offset" (e.g. name_off in "struct btf_type").

The to-be-added "struct bpf_line_info" also has another
member, "insn_off" which is the same as the "insn_offset"
in "struct bpf_func_info".  Hence, this patch renames "insn_offset"
to "insn_off" for "struct bpf_func_info".
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

1) When bpf_dump_raw_ok() == false and the kernel can provide >=1
   func_info to the userspace, the current behavior is setting
   the info.func_info_cnt to 0 instead of setting info.func_info
   to 0.

   It is different from the behavior in jited_func_lens/nr_jited_func_lens,
   jited_ksyms/nr_jited_ksyms...etc.

   This patch fixes it. (i.e. set func_info to 0 instead of
   func_info_cnt to 0 when bpf_dump_raw_ok() == false).

2) When the userspace passed in info.func_info_cnt == 0, the kernel
   will set the expected func_info size back to the
   info.func_info_rec_size.  It is a way for the userspace to learn
   the kernel expected func_info_rec_size introduced in
   commit 838e9690 ("bpf: Introduce bpf_func_info").

   An exception is the kernel expected size is not set when
   func_info is not available for a bpf_prog.  This makes the
   returned info.func_info_rec_size has different values
   depending on the returned value of info.func_info_cnt.

   This patch sets the kernel expected size to info.func_info_rec_size
   independent of the info.func_info_cnt.

3) The current logic only rejects invalid func_info_rec_size if
   func_info_cnt is non zero.  This patch also rejects invalid
   nonzero info.func_info_rec_size and not equal to the kernel
   expected size.

4) Set info.btf_id as long as prog->aux->btf != NULL.  That will
   setup the later copy_to_user() codes look the same as others
   which then easier to understand and maintain.

   prog->aux->btf is not NULL only if prog->aux->func_info_cnt > 0.

   Breaking up info.btf_id from prog->aux->func_info_cnt is needed
   for the later line info patch anyway.

   A similar change is made to bpf_get_prog_name().

Fixes: 838e9690 ("bpf: Introduce bpf_func_info")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

BPF programs can use the bpf_trace_printk() helper to print debug
information into the trace pipe. Add a subcommand
"bpftool prog tracelog" to simply dump this pipe to the console.

This is for a good part copied from iproute2, where the feature is
available with "tc exec bpf dbg". Changes include dumping pipe content
to stdout instead of stderr and adding JSON support (content is dumped
as an array of strings, one per line read from the pipe). This version
is dual-licensed, with Daniel's permission.

Cc: Daniel Borkmann <daniel@iogearbox.net>
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Ard Biesheuvel says:

====================
On arm64, modules are allocated from a 128 MB window which is close to
the core kernel, so that relative direct branches are guaranteed to be
in range (except in some KASLR configurations). Also, module_alloc()
is in charge of allocating KASAN shadow memory when running with KASAN
enabled.

This means that the way BPF reuses module_alloc()/module_memfree() is
undesirable on arm64 (and potentially other architectures as well),
and so this series refactors BPF's use of those functions to permit
architectures to change this behavior.

Patch #1 breaks out the module_alloc() and module_memfree() calls into
__weak functions so they can be overridden.

Patch #2 implements the new alloc/free overrides for arm64

Changes since v3:
- drop 'const' modifier for free() hook void* argument
- move the dedicated BPF region to before the module region, putting it
  within 4GB of the module and kernel regions on non-KASLR kernels

Changes since v2:
- properly build time and runtime tested this time (log after the diffstat)
- create a dedicated 128 MB region at the top of the vmalloc space for BPF
  programs, ensuring that the programs will be in branching range of each
  other (which we currently rely upon) but at an arbitrary distance from
  the kernel and modules (which we don't care about)

Changes since v1:
- Drop misguided attempt to 'fix' and refactor the free path. Instead,
  just add another __weak wrapper for the invocation of module_memfree()
====================

Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Rick Edgecombe <rick.p.edgecombe@intel.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jann Horn <jannh@google.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Jessica Yu <jeyu@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

The arm64 module region is a 128 MB region that is kept close to
the core kernel, in order to ensure that relative branches are
always in range. So using the same region for programs that do
not have this restriction is wasteful, and preferably avoided.

Now that the core BPF JIT code permits the alloc/free routines to
be overridden, implement them by vmalloc()/vfree() calls from a
dedicated 128 MB region set aside for BPF programs. This ensures
that BPF programs are still in branching range of each other, which
is something the JIT currently depends upon (and is not guaranteed
when using module_alloc() on KASLR kernels like we do currently).
It also ensures that placement of BPF programs does not correlate
with the placement of the core kernel or modules, making it less
likely that leaking the former will reveal the latter.

This also solves an issue under KASAN, where shadow memory is
needlessly allocated for all BPF programs (which don't require KASAN
shadow pages since they are not KASAN instrumented)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

By default, BPF uses module_alloc() to allocate executable memory,
but this is not necessary on all arches and potentially undesirable
on some of them.

So break out the module_alloc() and module_memfree() calls into __weak
functions to allow them to be overridden in arch code.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Lorenz Bauer says:

====================
Right now, there is no safe way to use BPF_PROG_TEST_RUN with data_out.
This is because bpf_test_finish copies the output buffer to user space
without checking its size. This can lead to the kernel overwriting
data in user space after the buffer if xdp_adjust_head and friends are
in play.

Thanks to everyone for their advice and patience with this patch set!

Changes in v5:
* Fix up libbpf.map

Changes in v4:
* Document bpf_prog_test_run and bpf_prog_test_run_xattr
* Use struct bpf_prog_test_run_attr for return values

Changes in v3:
* Introduce bpf_prog_test_run_xattr instead of modifying the existing
  function

Changes in v2:
* Make the syscall return ENOSPC if data_size_out is too small
* Make bpf_prog_test_run return EINVAL if size_out is missing
* Document the new behaviour of data_size_out
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Make sure that bpf_prog_test_run_xattr returns the correct length
and that the kernel respects the output size hint. Also check
that errno indicates ENOSPC if there is a short output buffer given.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Add a new function, which encourages safe usage of the test interface.
bpf_prog_test_run continues to work as before, but should be considered
unsafe.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Pull changes from "bpf: respect size hint to BPF_PROG_TEST_RUN if present".
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Use data_size_out as a size hint when copying test output to user space.
ENOSPC is returned if the output buffer is too small.
Callers which so far did not set data_size_out are not affected.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

When NULL pointer accidentally passed to write_kprobe_events,
due to strlen(NULL), segmentation fault happens.
Changed code returns -1 to deal with this situation.

Bug issued with Smatch, static analysis.
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

The missing indentation on the "Return" sections for bpf_map_pop_elem()
and bpf_map_peek_elem() helpers break RST and man pages generation. This
patch fixes them, and moves the description of those two helpers towards
the end of the list (even though they are somehow related to the three
first helpers for maps, the man page explicitly states that the helpers
are sorted in chronological order).

While at it, bring other minor formatting edits for eBPF helpers
documentation: mostly blank lines removal, RST formatting, or other
small nits for consistency.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

The pkt_len field in qdisc_skb_cb stores the skb length as it will
appear on the wire after segmentation. For byte accounting, this value
is more accurate than skb->len. It is computed on entry to the TC
layer, so only valid there.

Allow read access to this field from BPF tc classifier and action
programs. The implementation is analogous to tc_classid, aside from
restricting to read access.

To distinguish it from skb->len and self-describe export as wire_len.

Changes v1->v2
  - Rename pkt_len to wire_len
Signed-off-by: Petar Penkov <ppenkov@google.com>
Signed-off-by: Vlad Dumitrescu <vladum@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

The whole libbpf is licensed as (LGPL-2.1 OR BSD-2-Clause). I missed it
while adding README.rst. Fix it and use same license as all other files
in libbpf do. Since I'm the only author of README.rst so far, no others'
permissions should be needed.

Fixes: 76d1b894 ("libbpf: Document API and ABI conventions")
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

The aux->func_info and aux->btf are leaked in the error out cases
during bpf_prog_load().  This patch fixes it.

Fixes: ba64e7d8 ("bpf: btf: support proper non-jit func info")
Cc: Yonghong Song <yhs@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Matteo Croce says:

====================
Small improvements to improve the readability and easiness
to use of the xdp1 sample.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>