- 06 Jan, 2015 15 commits
-
-
Xinming Hu authored
This patch adds support to dump driver information to a file when firmware dump happens. This information can be used to root casue FW crash. Signed-off-by:
Xinming Hu <huxm@marvell.com> Signed-off-by:
Cathy Luo <cluo@marvell.com> Signed-off-by:
Avinash Patil <patila@marvell.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Xinming Hu authored
mwifiex_debug_info also need be save to file when firmware dump happens. Move its dump implementation function to commmon utilility file, thus it can be reused in firmware dump function. Signed-off-by:
-
Xinming Hu authored
Move mwifiex_pm_wakeup_card_complete handler to source file. Signed-off-by:
-
Xinming Hu authored
This patch add a new debugfs item histogram used for reporting rx data packet statitics(rx rate, snr, noise floor, signal strenth) to userspace. Signed-off-by:
-
Xinming Hu authored
This patch add receive beacon count and miss beacon count statistics in debugfs getlog item. Signed-off-by:
-
Xinming Hu authored
This patch add provision to show TDLS peer table in debugfs file. Signed-off-by:
-
Wolfram Sang authored
This platform_driver does not need to set an owner, it will be populated by the driver core. Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Arend van Spriel authored
When the driver gets beacon info containing a country IE from user-space upon .start_ap() callback, it will enable regulatory 802.11d support. Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by:
Hante Meuleman <meuleman@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
-
Hante Meuleman authored
Use cfg80211 change_station to signal the completion of 802.1x to firmware. This allows FW to take appropriate actions. Reviewed-by:
-
Arend van Spriel authored
When user-space uses a valid ISO-3166-1 country code for its regulatory domain selection, the driver will try to configure the firmware to use the same. Reviewed-by:
-
Hante Meuleman authored
When there is no room in the ring for rxbufpost an error is logged, however this happens quite frequently and can be considered normal and is certainly recoverable. This patch changes the erorr into a normal msgbuf log. Reviewed-by:
-
Hante Meuleman authored
When a device is configured for AP mode and it is configured for WEP then the keys are plumbed first, followed by AP configuration. During configuration a down command is given to the firmware which will clear the configured keys. This patch reprograms the WEP keys after AP has been brought up. Reviewed-by:
-
Arend van Spriel authored
The source file chip.c contained some duplicate defines and some unused ones. Removing them. Reviewed-by:
-
Hante Meuleman authored
The physical addresses being used by pcie and msgbuf were using a cast to long, which incorrectly caused it to limit the address to 32bit. Now explicit u64 is used where needed. Reviewed-by:
-
Kalle Valo authored
Merge tag 'iwlwifi-next-for-kalle-2014-12-30' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next * more work on d0i3 power state * enhancements to the firmware debugging infrastructure * support for 2 concurrent channel contexts * fixes / cleanups in the rate control * general cleanups
-
- 02 Jan, 2015 21 commits
-
-
David S. Miller authored
Richard Cochran says: ==================== Fixing the "Time Counter fixes and improvements" For this series I had only tested the build with ARCH=x86 and arm, but others like sparc64, microblaze, powerpc, and s390 will fail because they somehow don't indirectly include clocksource.h for the drivers in question. This series fixes the build issues reported by: kbuild test robot <fengguang.wu@intel.com> ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Richard Cochran authored
The timecounter/cyclecounter code has moved, so users need the new include. Signed-off-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
-
Richard Cochran authored
This driver uses the function, clocksource_khz2mult, and so it really must include clocksource.h. Signed-off-by:
-
Richard Cochran authored
Signed-off-by:
-
Richard Cochran authored
Signed-off-by:
-
Richard Cochran authored
Signed-off-by:
-
Richard Cochran authored
Signed-off-by:
-
Richard Cochran authored
There is no need for users of the timecounter/cyclecounter code to include clocksource.h just for a single macro. Signed-off-by:
-
Pravin B Shelar authored
OVS development is moved to netdev mailing list. Update tree and list in MAINTAINERS file. Signed-off-by:
Pravin B Shelar <pshelar@nicira.com> Signed-off-by:
-
David S. Miller authored
Merge tag 'wireless-drivers-next-for-davem-2015-01-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Changes: * ath9k: enable Transmit Power Control (TPC) for ar9003 chips * rtlwifi: cleanup and updates from the vendor driver * rsi: fix memory leak related to firmware image * ath: parameter fix for FCC DFS pattern Signed-off-by:
-
Rickard Strandqvist authored
Removes some functions that are not used anywhere: enic_dev_enable2_done() enic_dev_enable2() enic_dev_deinit_done() enic_dev_init_prov2() enic_vnic_dev_deinit() This was partially found by using a static code analysis program called cppcheck. Signed-off-by:
Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se> Signed-off-by:
-
Rickard Strandqvist authored
Removes some functions that are not used anywhere: Read_hfc32() Write_hfc32() Write_hfc16() This was partially found by using a static code analysis program called cppcheck. Signed-off-by:
-
Rickard Strandqvist authored
Remove the function smt_ifconfig() that is not used anywhere. This was partially found by using a static code analysis program called cppcheck. Signed-off-by:
-
Rickard Strandqvist authored
Removes some functions that are not used anywhere: dbgi_rd_rsp3() dbgi_wr_addr3() This was partially found by using a static code analysis program called cppcheck. Signed-off-by:
-
Florian Westphal authored
Not needed, only four cases: - kfree_skb (or one of its aliases). Don't need to zero, memory will be freed. - kfree_skb_partial and head was stolen: memory will be freed. - skb_morph: The skb header fields (including tc ones) will be copied over from the 'to-be-morphed' skb right after skb_release_head_state returns. - skb_segment: Same as before, all the skb header fields are copied over from the original skb right away. Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
-
David S. Miller authored
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next Johan Hedberg say: ==================== pull request: bluetooth-next 2014-12-31 Here's the first batch of bluetooth patches for 3.20. - Cleanups & fixes to ieee802154 drivers - Fix synchronization of mgmt commands with respective HCI commands - Add self-tests for LE pairing crypto functionality - Remove 'BlueFritz!' specific handling from core using a new quirk flag - Public address configuration support for ath3012 - Refactor debugfs support into a dedicated file - Initial support for LE Data Length Extension feature from Bluetooth 4.2 Please let me know if there are any issues pulling. Thanks. ==================== Signed-off-by:
-
Joe Stringer authored
This results in an approximately 30% increase in throughput when handling encapsulated bulk traffic. Signed-off-by:
Joe Stringer <joestringer@nicira.com> Signed-off-by:
Jesse Gross <jesse@nicira.com> Signed-off-by:
-
Jesse Gross authored
Currently the only tunnel protocol that supports GRO with encapsulated Ethernet is VXLAN. This pulls out the Ethernet code into a proper layer so that it can be used by other tunnel protocols such as GRE and Geneve. Signed-off-by:
-
Shaohui Xie authored
There is no need to set the clock speed in read/write which will be performed unnecessarily for each mdio access. Init it during probe is enough. Also, the hardcoded clock value is not a proper way for all SoCs. Signed-off-by:
Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by:
-
Shaohui Xie authored
Which is wrong and not used, so no extra space needed by mdiobus_alloc_size(), use mdiobus_alloc() instead. Signed-off-by:
-
Shaohui Xie authored
Since the reset is just clock setting, individual mdio reset is not available. Signed-off-by:
-
- 01 Jan, 2015 4 commits
-
-
David S. Miller authored
Roger Chen says: ==================== support GMAC driver for RK3288 Roger Chen (6): patch1: add driver for Rockchip RK3288 SoCs integrated GMAC patch2: define clock ID used for GMAC patch3: modify CRU config for Rockchip RK3288 SoCs integrated GMAC patch4: dts: rockchip: add gmac info for rk3288 patch5: dts: rockchip: enable gmac on RK3288 evb board patch6: add document for Rockchip RK3288 GMAC Tested on rk3288 evb board: Execute the following command to enable ethernet, set local IP and ping a remote host. busybox ifconfig eth0 up busybox ifconfig eth0 192.168.1.111 ping 192.168.1.1 ==================== Signed-off-by: -
Roger Chen authored
The document descripts how to add properties for GMAC in device tree. change since v2: 1. remove power-gpio, reset-gpio, phyirq-gpio, pmu_regulator setting 2. add "snps,reset-gpio", "snps,reset-active-low;" "snps,reset-delays-us" Signed-off-by:
Roger Chen <roger.chen@rock-chips.com> Signed-off-by:
-
Roger Chen authored
enable gmac in rk3288-evb-rk808.dts changes since v2: 1. add fixed regulator for PHY 2. remove power-gpio, reset-gpio, phyirq-gpio, pmu_regulator setting 3. add "snps,reset-gpio", "snps,reset-active-low;" "snps,reset-delays-us" Signed-off-by:
-
Roger Chen authored
add gmac info in rk3288.dtsi for GMAC driver changes since v2: 1. add drive-strength in the pinctrl settings Signed-off-by:
-
