- 08 Jul, 2016 40 commits
-
-
Hans Verkuil authored
Like the videodev2.h and other headers, explicitly allow these headers to be used with the BSD license. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com>
-
Hans Verkuil authored
When a reply to an earlier transmit is received, the tx_status of that transmit needs to be restored. Otherwise the status that the transmit was successful would be lost. Signed-off-by:
-
Kamil Debski authored
Add the keymap module for HDMI CEC remote control commands. Signed-off-by:
Kamil Debski <kamil@wypas.org> Signed-off-by:
-
Mauro Carvalho Chehab authored
* topic/cec: [media] DocBook/media: add CEC documentation [media] s5p_cec: get rid of an unused var [media] move s5p-cec to staging [media] vivid: add CEC emulation [media] cec: s5p-cec: Add s5p-cec driver [media] cec: adv7511: add cec support [media] cec: adv7842: add cec support [media] cec: adv7604: add cec support [media] cec: add compat32 ioctl support [media] cec/TODO: add TODO file so we know why this is still in staging [media] cec: add HDMI CEC framework (api) [media] cec: add HDMI CEC framework (adapter) [media] cec: add HDMI CEC framework (core) [media] cec-funcs.h: static inlines to pack/unpack CEC messages [media] cec.h: add cec header [media] cec-edid: add module for EDID CEC helper functions [media] cec.txt: add CEC framework documentation [media] rc: Add HDMI CEC protocol handling
-
Mauro Carvalho Chehab authored
Linux 4.7-rc6 * tag 'v4.7-rc6': (1245 commits) Linux 4.7-rc6 ovl: warn instead of error if d_type is not supported MIPS: Fix possible corruption of cache mode by mprotect. locks: use file_inode() usb: dwc3: st: Use explicit reset_control_get_exclusive() API phy: phy-stih407-usb: Use explicit reset_control_get_exclusive() API phy: miphy28lp: Inform the reset framework that our reset line may be shared namespace: update event counter when umounting a deleted dentry 9p: use file_dentry() lockd: unregister notifier blocks if the service fails to come up completely ACPI,PCI,IRQ: correct operator precedence fuse: serialize dirops by default drm/i915: Fix missing unlock on error in i915_ppgtt_info() powerpc: Initialise pci_io_base as early as possible mfd: da9053: Fix compiler warning message for uninitialised variable mfd: max77620: Fix FPS switch statements phy: phy-stih407-usb: Inform the reset framework that our reset line may be shared usb: dwc3: st: Inform the reset framework that our reset line may be shared usb: host: ehci-st: Inform the reset framework that our reset line may be shared usb: host: ohci-st: Inform the reset framework that our reset line may be shared ...
-
Heiner Kallweit authored
These two fields are not used and can be removed. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Heiner Kallweit authored
If the logical device is disabled then it can not generate interrupts. Therefore this check is not needed. Signed-off-by:
-
Heiner Kallweit authored
Simplify interupt handling code. Signed-off-by:
-
Heiner Kallweit authored
Study states have never been used and are not needed. Remove them. Signed-off-by:
-
Heiner Kallweit authored
The definition of rawir includes the initialization already. Signed-off-by:
-
Heiner Kallweit authored
Simplify a few functions. Signed-off-by:
-
Heiner Kallweit authored
Wake states have never been in use and now that we can set the wakeup sequence via sysfs there's in general no need for them. Signed-off-by:
-
Heiner Kallweit authored
The registers defining wakeup sequence handling are set when the wakeup sequence is set via sysfs. There's no need to initialize them otherwise. Signed-off-by:
-
Heiner Kallweit authored
There is a rudimentary ISR for handling interrupts generated by the wakeup part of the chip. Interrupts however have never been enabled in the wakeup part. Also, now that we can set the wakeup sequence via sysfs, there's in general no need to enable interrupts in the wakeup part. Signed-off-by:
-
Heiner Kallweit authored
To detect a rx fifo overrun it's checked whether the number of elements in the chip fifo exceeds the fifo size. This check can never return true and is wrong. Instead we should generate an interrupt if the fifo overruns. Signed-off-by:
-
Antti Palosaari authored
Disable runtime unbind as driver does not support it. Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Antti Palosaari authored
Move statistics polling to read_status() in order to avoid use of kernel work. Also replace home made sign extension used for statistics with kernel sign_extend32(). Signed-off-by:
-
Antti Palosaari authored
Disable runtime unbind as driver does not support it. Signed-off-by:
-
Antti Palosaari authored
Disable runtime unbind as driver does not support it. Signed-off-by:
-
Antti Palosaari authored
Disable runtime unbind as driver does not support it. Signed-off-by:
-
Antti Palosaari authored
Move statistics polling to read_status() in order to avoid use of kernel work. Signed-off-by:
-
Antti Palosaari authored
* remove some unneeded variable initialization * rename variables * use min() macro to calc max i2c xfer len * change bad firmware error code from EFAULT to EINVAL Signed-off-by:
-
Antti Palosaari authored
There was some calculations where was kHz used in order to keep calculation withing 32-bit. Convert all to Hz and use 64-bit division helpers where needed. Signed-off-by:
-
Antti Palosaari authored
Simplify TS clock divider calculation and programming slightly. Signed-off-by:
-
Antti Palosaari authored
DiSEqC message sending takes 13.5 ms per byte, which is 54 ms total when typical 4 byte message is sent. Don't hard-code time limit to 54 ms, but calculate it. Time limit is only used to determine when to start poll "DiSEqC Tx ready" status from the chip. Signed-off-by:
-
Antti Palosaari authored
No need to clear negative msb bits as those were dropped in any case when data is written to register. Signed-off-by:
-
Antti Palosaari authored
Disable runtime unbind as driver does not support it. Signed-off-by:
-
Antti Palosaari authored
Disable runtime unbind as driver does not support it. Signed-off-by:
-
Antti Palosaari authored
Si2168-B40 firmware API has changed somewhere between 4.0-11 and 4.0-19 so that sleep will lose firmware upgrade from the chip. Due to that firmware re-upload is needed when newer firmwares are used. Rewrote firmware handling logic partly at the same. Signed-off-by:
-
Hans Verkuil authored
Fix sparse warnings: tw686x-video.c:148:29: warning: symbol 'memcpy_dma_ops' was not declared. Should it be static? tw686x-video.c:195:29: warning: symbol 'contig_dma_ops' was not declared. Should it be static? tw686x-video.c:361:29: warning: symbol 'sg_dma_ops' was not declared. Should it be static? Signed-off-by:
-
Dragos Bogdan authored
The part can be reset by a low pulse on the RESET pin (i.e. a hardware reset) with a minimum width of 5 ms. It is recommended to wait 5 ms after the low pulse before an I2C write is performed to the part. For safety reasons, the delays will be between 5 and 10 ms. The RESET pin can be tied high, so the GPIO is optional. Signed-off-by:
Dragos Bogdan <dragos.bogdan@analog.com> Reviewed-by:
Lars-Peter Clausen <lars@metafoo.de> Acked-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Amitoj Kaur Chawla authored
vzalloc combines vmalloc and memset 0. The Coccinelle semantic patch used to make this change is as follows: @@ type T; T *d; expression e; statement S; @@ d = - vmalloc + vzalloc (...); if (!d) S - memset(d, 0, sizeof(T)); Signed-off-by:Amitoj Kaur Chawla <amitoj1606@gmail.com> Signed-off-by:
-
Arnd Bergmann authored
The dvb demuxer code uses a 'struct timespec' to pass a timeout as absolute time. This will cause problems on 32-bit architectures in 2038 when time_t overflows, and it is racy with a concurrent settimeofday() call. This patch changes the code to use ktime_get() instead, using the monotonic time base to avoid both the race and the overflow. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Alexander Shiyan authored
Commit 39b4da71 ("reset: use ENOTSUPP instead of ENOSYS") changed return value for reset controller if it missing. This patch changes the CODA driver to handle this value. Signed-off-by:
Alexander Shiyan <shc_work@mail.ru> Signed-off-by:
-
Guennadi Liakhovetski authored
A copy paste error created that format with the same one-line description as Y8I and Y12I, whereas Z16 is quite different from them both. Signed-off-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Ricardo Ribalda authored
The comment was referencing the wrong function. Signed-off-by:
Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Acked-by:
-
Ricardo Ribalda authored
After all the code refactoring, vb2_internal_qbuf is only called by vb2_qbuf. Since the function it is very simple, there is no need to have two functions. Signed-off-by:
-
Ricardo Ribalda authored
After all the code refactoring, vb2_internal_dqbuf is only called by vb2_dqbuf. Since the function it is very simple, there is no need to have two functions. Signed-off-by:
-
Ricardo Ribalda authored
According to the doc, V4L2_BUF_FLAG_DONE is cleared after DQBUF: V4L2_BUF_FLAG_DONE 0x00000004 ... After calling the VIDIOC_QBUF or VIDIOC_DQBUF it is always cleared ... Unfortunately, it seems that videobuf2 keeps it set after DQBUF. This can be tested with vivid and dev_debug: [257604.338082] video1: VIDIOC_DQBUF: 71:33:25.00260479 index=3, type=vid-cap, flags=0x00002004, field=none, sequence=163, memory=userptr, bytesused=460800, offset/userptr=0x344b000, length=460800 This patch forces FLAG_DONE to 0 after calling DQBUF. Reported-by:
Dimitrios Katsaros <patcherwork@gmail.com> Signed-off-by:
-
Hans Verkuil authored
Don't fill in the format description. This is now done in the V4L2 core to ensure consistent descriptions. Signed-off-by:
Nick Dyer <nick.dyer@itdev.co.uk> Signed-off-by:
-
