If the EEPROM was partially overwritten (which seems to happen before the OS is
booted), restore its entire contents by deducing it from the remaining
information.

This does not have any effect on the Linux driver, which works even with
incomplete information in the EEPROM, but it makes other drivers work again.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Under as yet unknown circumstances, the first word of the sound card's
EEPROM gets overwritten.  When this has happened, we cannot rely on the
subsystem IDs that the kernel reads from the PCI configuration
registers.  Instead, we read the IDs directly from the EEPROM and do the
ID matching manually.

Because the model-specific driver cannot determine the model before
calling oxygen_pci_probe(), that function now gets a get_model()
callback as parameter.  The customizing of the model structure, which
was formerly done by the probe() callback, also has moved into
get_model().
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When allocating resources, use a fixed name instead of reading it from
the model structure.  This allows us to allocate the resources before
the actual model is known.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Allocate the model-specific data dynamically instead of including it in
the memory block of the card structure.  This will allow us to determine
the actual model after the card creation.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Move the owner field out of the oxygen_model structure and make it
a parameter of oxygen_pci_probe(), because the actual owner module does
not depend on the card model.  Furthermore, moving it out of the model
structure allows us to create the card structure before the actual model
is known.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This reverts commit 7e86c0e6 ("do not
overwrite EEPROM on Xonar D2/D2X") because it did not actually help with
the problem.

More user reports show that the overwriting of the EEPROM is not
triggered by using this driver but by installing Linux, and that the
installation of any other operating system (even one without any CMI8788
driver) has the same effect.  In other words, the presence of this
driver does not have any effect on the occurrence of the error.  (So
far, the available evidence seems to point to a BIOS bug.)

Furthermore, it turns out that the EEPROM chip is protected against
stray write commands by the command format and by requiring a separate
write-enable command, so the error scenario in the previous commit (that
SPI writes can be misinterpreted as an EEPROM write command) is not even
theoretically possible.

The mixer control that was removed as a consequence of the previous
commit can only be partially emulated in userspace, which also means it
cannot be seen be the in-kernel OSS API emulation, so it is better to
revert that change.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Currently the jack layer refers to card->longname as a part of
its input device name string.  However, longname is often really long
and way too ugly as an identifier, such as,
"HDA Intel at 0xf8400000 irq 21".

This patch changes the code to use card->shortname instead.
The shortname string contains usually the h/w vendor and product
names but without messy I/O port or IRQ numbers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ASoC: Only register AC97 bus if it's not done already
  ALSA: hda - Add snd_hda_multi_out_dig_cleanup()
  ALSA: hda - Add missing terminator in slave dig-out array
  ALSA: hda - Change HP dv7 (103c:30f4) quirk from hp-m4 to hp-dv5 model
  ALSA: hda - Register (new) devices at reconfig
  ALSA: mtpav - Fix initial value for input hwport
  ALSA: hda - add id for Intel IbexPeak integrated HDMI codec
  ALSA: hda - compute checksum in HDMI audio infoframe
  ALSA: hda - enable HDMI audio pin out at module loading time
  ALSA: hda - allow multi-channel HDMI audio playback when ELD is not present
  ASoC: Update SDP3430 machine driver for snd_soc_card
  ALSA: hda - Add quirk for Asus z37e (1043:8284)
  sound: Remove OSSlib stuff from linux/soundcard.h
  ASoC: WM8990: Fix kcontrol's private value use in put callback
  ASoC: TLV320AIC3X: Fix kcontrol's private value use in put callback

uids in namespaces other than init don't get a sysfs entry.

For those in the init namespace, while we're waiting to remove
the sysfs entry for the uid the uid is still hashed, and
alloc_uid() may re-grab that uid without getting a new
reference to the user_ns, which we've already put in free_user
before scheduling remove_user_sysfs_dir().
Reported-and-tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Acked-by: David Howells <dhowells@redhat.com>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ASoC supports both explicit codec drivers for AC97 devices and a simple
driver which uses the standard ALSA AC97 framework for codec support.
When used with the generic AC97 codec support that will provide the
ad hoc AC97 device for drivers like touchscreens to attach to so the
core shouldn't do so.
Reported-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Added the helper function snd_hda_multi_out_dig_cleanup() to clean up
the digital outputs with multi setup.  This call is needed in cases
the codec supports multiple digital outputs as slaves.  Otherwise the
slave widgets aren't properly cleaned up.

For a single digital output (e.g. in patch_conexant.c), this call isn't
needed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Added the missing terminator for ad1989b_slave_dig_outs[].

Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Change HP dv7 quirk: although reported to work with hp-m4 model
(https://bugzilla.novell.com/show_bug.cgi?id=445321), the original
report doesn't contain info about testing of internal microphone.

Recently I received a report about internal mic not working
(https://qa.mandriva.com/show_bug.cgi?id=44855#c193), this must be
related with the forced line in on pin 0x0e done with hp-m4 model. Thus
change the current quirk from STAC_HP_M4 to STAC_HP_DV5, later reported
to be fixed on a provided kernel with this change
(https://qa.mandriva.com/show_bug.cgi?id=44855#c196).
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
  wimax: fix oops in wimax_dev_get_by_genl_info() when looking up non-wimax iface
  net: 4 bytes kernel memory disclosure in SO_BSDCOMPAT gsopt try #2
  netxen: fix compile waring "label ‘set_32_bit_mask’ defined but not used" on IA64 platform
  bnx2: Update version to 1.9.2 and copyright.
  bnx2: Fix jumbo frames error handling.
  bnx2: Update 5709 firmware.
  bnx2: Update 5706/5708 firmware.
  3c505: do not set pcb->data.raw beyond its size
  Documentation/connector/cn_test.c: don't use gfp_any()
  net: don't use in_atomic() in gfp_any()
  IRDA: cnt is off by 1
  netxen: remove pcie workaround
  sun3: print when lance_open() fails
  qlge: bugfix: Add missing rx buf clean index on early exit.
  qlge: bugfix: Fix RX scaling values.
  qlge: bugfix: Fix TSO breakage.
  qlge: bugfix: Add missing dev_kfree_skb_any() call.
  qlge: bugfix: Add missing put_page() call.
  qlge: bugfix: Fix fatal error recovery hang.
  qlge: bugfix: Use netif_receive_skb() and vlan_hwaccel_receive_skb().
  ...

When a non-wimax interface is looked up by the stack, a bad pointer is
returned when the looked-up interface is not found in the list (of
registered WiMAX interfaces). This causes an oops in the caller when
trying to use the pointer.

Fix by properly setting the pointer to NULL if we don't exit from the
list_for_each() with a found entry.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In function sock_getsockopt() located in net/core/sock.c, optval v.val
is not correctly initialized and directly returned in userland in case
we have SO_BSDCOMPAT option set.

This dummy code should trigger the bug:

int main(void)
{
	unsigned char buf[4] = { 0, 0, 0, 0 };
	int len;
	int sock;
	sock = socket(33, 2, 2);
	getsockopt(sock, 1, SO_BSDCOMPAT, &buf, &len);
	printf("%x%x%x%x\n", buf[0], buf[1], buf[2], buf[3]);
	close(sock);
}

Here is a patch that fix this bug by initalizing v.val just after its
declaration.
Signed-off-by: Clément Lecigne <clement.lecigne@netasq.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When compile the latest kernel on IA64 platform,I got a warning:
drivers/net/netxen/netxen_nic_main.c:203: warning: label ‘set_32_bit_mask’ 
defined but not used

We do not need label ‘set_32_bit_mask’  on IA64 platform,So move it to #else.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If errors are reported on a frame descriptor, we need to
account for the buffer pages that may have been used for this
error packet and recycle them.  Otherwise, we may get the wrong
pages for the next packet.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

New firmware fixes a data corruption issue when receiving and
placing jumbo frames into host buffers.  In some cases, the
buffer descriptor is not updated correctly and this will lead
to the driver linking the wrong number of pages into the SKB.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

New firmware fixes a data corruption issue when receiving and
placing jumbo frames into host buffers.  In some cases, the
buffer descriptor is not updated correctly and this will lead
to the driver linking the wrong number of pages into the SKB.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ensure that we do not set pcb->data.raw beyond its size, print an error message
and return false if we attempt to. A timout message was printed one too early.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cn_test_timer_func() is a timer handler and can never use GFP_KERNEL -
there's no point in using gfp_any() here.

Also, use setup_timer().
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The problem is that in_atomic() will return false inside spinlocks if
CONFIG_PREEMPT=n.  This will lead to deadlockable GFP_KERNEL allocations
from spinlocked regions.

Secondly, if CONFIG_PREEMPT=y, this bug solves itself because networking
will instead use GFP_ATOMIC from this callsite.  Hence we won't get the
might_sleep() debugging warnings which would have informed us of the buggy
callsites.

Solve both these problems by switching to in_interrupt().  Now, if someone
runs a gfp_any() allocation from inside spinlock we will get the warning
if CONFIG_PREEMPT=y.

I reviewed all callsites and most of them were too complex for my little
brain and none of them documented their interface requirements.  I have no
idea what this patch will do.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If no prior break occurs, cnt reaches 101 after the loop, so we are still able
to change speed when cnt has become 100.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove workaround for pcie bug in early revisions of NX3031
(rev 41 or earlier). This is taken care of during firmware init.

The workaround required writing pcie config reg of every
pcie function on a card, not all of which are enabled.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With while (--i > 0) { ... } i reaches 0; print when lance_open() fails
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The large receive buffer queue is not properly tracking the current
index in the case where an early exit occurs.  This can happen when a
page alloc or dma mapping fails.  If this occurs the queue will get
out of sync and invalid indexes can be written to the hardware.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Receive packets were only scaling across 2 of the receive queues. The
value was hardcoded to 2 instead of being based on how many rx queues
were running.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Moved the buffer mapping to a point after TSO logic has modified the
iph->check field. We were seeing stale data on the PCIe bus.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We put the skb back if we can't get mapping for it.  We don't
want unmapped buffers on our receive buffer queue.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We put the page back if we can't get mapping for it.  We don't
want unmapped buffers on our receive buffer queue.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace calls to vlan_hwaccel_rx() and netif_rx().
Thanks to Dave Miller for pointing out the the driver was making
the wrong upcall for passing packets into the stack.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>