The byte mode support fails to clear the byte mode bit in the command
register, possibly leaving byte mode enabled with the counters programmed
in non-byte mode.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

According to the documentation the AT91SAM9261 MCI shares the block size
limitations of the AT91RM9200 MCI. Also the errata documentation for
AT91RM9200 and AT91SAM9261 state that stream commands are not supported.
This has not been tested on actual hardware.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

AT91SAM926[0/3] PDC must write at least 12 bytes. The code compiles and runs
but the actual condition for this erratum did not trigger in my tests so it's
unclear if it actually works as intended.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

In at91_mci_completed_command() function, this patch distinguishes
command error and data error. It reports it in the corresponding
error field.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Reading AT91_MCI_SR again at the end of transfer can corrupt the
error reporting. Some fields in the SR register are read-and-clear.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Enable SDIO interrupt handling.
Signed-off-by: Eric Benard <ebenard@free.fr>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

at91_mci is capable of multiwrite. Enable it before it disappears.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Modify bytes_xfered value after a write.

That will report, as accurately as possible, the amount of
sectors that are effectively written.

This update introduces the check of the busy signal given by
the card.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

The at91 mci controller internal state machine seems to often crash. This can
be fixed by resetting the controller after each command for at91rm9200 and by
setting the MCI_BLKR register on at91sam926*.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Hans J Koch <hjk@linutronix.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Detect command timeout (or mci controller hangs).
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Hans J Koch <hjk@linutronix.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Implement transfer with size not modulo 4 for at91sam9*. Please note that the
at91rm9200 simply can't handle this.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Make the variable name in the comments match the actual name
of the variable.
Signed-off-by: Deepak Saxena <dsaxena@laptop.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Now get_ro() callback must return 0/1 values for its logical states, and
negative errno values in case of error. If particular host instance doesn't
support RO/WP switch, it should return -ENOSYS.

This patch changes some hosts in two ways:

1. Now functions should be smart to not return negative values in
   "RO asserted" case (particularly gpio_ calls could return negative
   values for the outermost GPIOs).

   Also, board code usually passes get_ro() callbacks that directly return
   gpioreg & bit result, so at91_mci, imxmmc, pxamci and mmc_spi's get_ro()
   handlers need take special care when returning platform's values to the
   mmc core.

2. In case of host instance didn't implement get_ro() callback, it should
   really return -ENOSYS and let the mmc core decide what to do about it
   (mmc core thinks the same way as the hosts, so it isn't functional
   change).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

This patch adds new platform data variable "caps", so platforms
could pass theirs capabilities into MMC core (for example, platforms
without interrupt on the CD line will most probably want to pass
MMC_CAP_NEEDS_POLL).

New platform get_cd() callback provided to optimize polling.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Some hosts (and boards that use mmc_spi) do not use interrupts on the CD
line, so they can't trigger mmc_detect_change. We want to poll the card
and see if there was a change. 1 second poll interval seems resonable.

This patch also implements .get_cd() host operation, that could be used
by the hosts that are able to report card-detect status without need to
talk MMC.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

This patch removes a CVS tag that wasn't updated for a long time.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

The Ricoh controllers cannot handle unaligned data blocks.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Add the ability to run just a single test case by writing the test
case number into the sysfs "test" file.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Gracefully handle when the device is suddenly removed. Do a test read
and avoid any further access if that read returns -1.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

JMicron chips sometimes have two interfaces to work around limitations
in Microsoft's sdhci driver. This patch allows us to use either interface.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Some of the JMicron chips requires us to manually enable the power
output stages of the chip. Add the necessary hooks and functions to
manage this.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Give the quirk for broken timeout handling a better chance of handling
more controllers by simply classifying the system as broken and setting
a fixed value.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Extend the quirks handling in the PCI driver to be able to have
callbacks and not just flags.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Remove the quirk to force DMA on the Ricoh and TI controllers as it is
no longer needed. The only bug they have is that they use an incorrect
PCI interface value, and that is not respected anymore.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

The SDHCI interface is not PCI specific, yet the Linux driver was
intimitely connected to the PCI bus. This patch properly separates
the PCI specific portion from the bus independent code.

This patch is based on work by Ben Dooks but he did not have time
to complete it.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

The specification is insufficiently strict when it comes to how the
hardware should update the block count register, making it useless
for checking transfer progress.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

When CONFIG_EXTRA_FIRMWARE_DIR gets changed, the filename in the .S file
(which uses .incbin to include the binary) needs to change. When we
renamed the BUILTIN_FIRMWARE_DIR option to EXTRA_FIRMWARE_DIR, we forgot
to update the manual dependency in firmware/Makefile, so it was
depending on a non-existent file in include/config/
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-2.6.27' of git://git.infradead.org/users/dwmw2/firmware-2.6: (64 commits)
  firmware: convert sb16_csp driver to use firmware loader exclusively
  dsp56k: use request_firmware
  edgeport-ti: use request_firmware()
  edgeport: use request_firmware()
  vicam: use request_firmware()
  dabusb: use request_firmware()
  cpia2: use request_firmware()
  ip2: use request_firmware()
  firmware: convert Ambassador ATM driver to request_firmware()
  whiteheat: use request_firmware()
  ti_usb_3410_5052: use request_firmware()
  emi62: use request_firmware()
  emi26: use request_firmware()
  keyspan_pda: use request_firmware()
  keyspan: use request_firmware()
  ttusb-budget: use request_firmware()
  kaweth: use request_firmware()
  smctr: use request_firmware()
  firmware: convert ymfpci driver to use firmware loader exclusively
  firmware: convert maestro3 driver to use firmware loader exclusively
  ...

Fix up trivial conflicts with BKL removal in drivers/char/dsp56k.c and
drivers/char/ip2/ip2main.c manually.

* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (241 commits)
  [ARM] 5171/1: ep93xx: fix compilation of modules using clocks
  [ARM] 5133/2: at91sam9g20 defconfig file
  [ARM] 5130/4: Support for the at91sam9g20
  [ARM] 5160/1: IOP3XX: gpio/gpiolib support
  [ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
  [ARM] 5084/1: zylonite: Register AC97 device
  [ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model
  [ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
  [ARM] 5147/1: pxaficp_ir: drop pxa_gpio_mode calls, as pin setting
  [ARM] 5145/1: PXA2xx: provide api to control IrDA pins state
  [ARM] 5144/1: pxaficp_ir: cleanup includes
  [ARM] pxa: remove pxa_set_cken()
  [ARM] pxa: allow clk aliases
  [ARM] Feroceon: don't disable BPU on boot
  [ARM] Orion: LED support for HP mv2120
  [ARM] Orion: add RD88F5181L-FXO support
  [ARM] Orion: add RD88F5181L-GE support
  [ARM] Orion: add Netgear WNR854T support
  [ARM] s3c2410_defconfig: update for current build
  [ARM] Acer n30: Minor style and indentation fixes.
  ...

Conflicts:

	sound/pci/Kconfig

This includes PXA work up to the SPI changes for the initial merge,
since e172274c depends on the SPI
tree being merged.

Conflicts:

	arch/arm/configs/em_x270_defconfig
	arch/arm/configs/xm_x270_defconfig

* 'core/softirq' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  softirq: remove irqs_disabled warning from local_bh_enable
  softirq: remove initialization of static per-cpu variable
  Remove argument from open_softirq which is always NULL

* 'core/rodata' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  move BUG_TABLE into RODATA

* 'core/printk' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, generic: mark early_printk as asmlinkage
  printk: export console_drivers
  printk: remember the message level for multi-line output
  printk: refactor processing of line severity tokens
  printk: don't prefer unsuited consoles on registration
  printk: clean up recursion check related static variables
  namespacecheck: more kernel/printk.c fixes
  namespacecheck: fix kernel printk.c

Even the help-text makes it clear that normal people shouldn't enable
it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'core/locking' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  lockdep: fix kernel/fork.c warning
  lockdep: fix ftrace irq tracing false positive
  lockdep: remove duplicate definition of STATIC_LOCKDEP_MAP_INIT
  lockdep: add lock_class information to lock_chain and output it
  lockdep: add lock_class information to lock_chain and output it
  lockdep: output lock_class key instead of address for forward dependency output
  __mutex_lock_common: use signal_pending_state()
  mutex-debug: check mutex magic before owner

Fixed up conflict in kernel/fork.c manually

Merge branch 'sched/new-API-sched_setscheduler' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched/new-API-sched_setscheduler' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: add new API sched_setscheduler_nocheck: add a flag to control access checks

* 'tracing/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (228 commits)
  ftrace: build fix for ftraced_suspend
  ftrace: separate out the function enabled variable
  ftrace: add ftrace_kill_atomic
  ftrace: use current CPU for function startup
  ftrace: start wakeup tracing after setting function tracer
  ftrace: check proper config for preempt type
  ftrace: trace schedule
  ftrace: define function trace nop
  ftrace: move sched_switch enable after markers
  ftrace: prevent ftrace modifications while being kprobe'd, v2
  fix "ftrace: store mcount address in rec->ip"
  mmiotrace broken in linux-next (8-bit writes only)
  ftrace: avoid modifying kprobe'd records
  ftrace: freeze kprobe'd records
  kprobes: enable clean usage of get_kprobe
  ftrace: store mcount address in rec->ip
  ftrace: build fix with gcc 4.3
  namespacecheck: fixes
  ftrace: fix "notrace" filtering priority
  ftrace: fix printout
  ...

* 'bkl-removal' of git://git.lwn.net/linux-2.6: (146 commits)
  IB/umad: BKL is not needed for ib_umad_open()
  IB/uverbs: BKL is not needed for ib_uverbs_open()
  bf561-coreb: BKL unneeded for open()
  Call fasync() functions without the BKL
  snd/PCM: fasync BKL pushdown
  ipmi: fasync BKL pushdown
  ecryptfs: fasync BKL pushdown
  Bluetooth VHCI: fasync BKL pushdown
  tty_io: fasync BKL pushdown
  tun: fasync BKL pushdown
  i2o: fasync BKL pushdown
  mpt: fasync BKL pushdown
  Remove BKL from remote_llseek v2
  Make FAT users happier by not deadlocking
  x86-mce: BKL pushdown
  vmwatchdog: BKL pushdown
  vmcp: BKL pushdown
  via-pmu: BKL pushdown
  uml-random: BKL pushdown
  uml-mmapper: BKL pushdown
  ...

Signed-off-by: Jaswinder Singh <jaswinder@infradead.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>