In dt-bindings for ufs, "<name>-max-microamp" property indicates current
limit and is mandatory if "<name>-fixed-regulator" is not defined on a
specified regulator.

However, in some platforms, regulators without "<name>-fixed-regulator"
property may not need to define their current limit because they may want
to define voltage range only for proper voltage switching in different
power modes, especially for vcc, vccq or vccq2.

Currently missing "<name>-max-microamp" property in device tree will lead
initialization to fail, thus such limitation shall be resolved to tolerate
this kind of regulators.

After resolving this, regulators without "<name>-max-microamp" property
will have undefined "max current" value, i.e., zero value in "max_uA" field
in struct ufs_vreg. Because we do bypass current switching operation (by
regulator_set_load) in case of undefined current limit, this patch shall be
safe.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Currently if a regulator has "<name>-fixed-regulator" property in device
tree, it will skip current limit initialization.  This lead to a zero
"max_uA" value in struct ufs_vreg.

However, "regulator_set_load" operation shall be required on regulators
which have valid current limits, otherwise a zero "max_uA" set by
"regulator_set_load" may cause unexpected behavior when this regulator is
enabled or set as high power mode.

Similarly, in device's icc_level configuration flow, the target icc_level
shall be updated if regulator also has valid current limit, otherwise a
wrong icc_level will be calculated by zero "max_uA" and thus causes
unexpected results after it is written to device.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

For regulators used by UFS, vcc, vccq and vccq2 will have voltage range
initialized by ufshcd_populate_vreg(), however other regulators may have
undefined voltage range if dt-bindings have no such definition.

In above undefined case, both "min_uV" and "max_uV" fields in ufs_vreg
struct will be zero values and these values will be configured on
regulators in different power modes.

Currently this may have no harm if both "min_uV" and "max_uV" always keep
"zero values" because regulator_set_voltage() will always bypass such
invalid values and return "good" results.

However improper values shall be fixed to avoid potential bugs.  Simply
bypass voltage configuration if voltage range is not defined.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

There are two fields related to regulator current limit in struct ufs_vreg:
"min_uA" and "max_uA".

"max_uA" is probed by "<name>-max-microamp" property from device tree and
used for

 - regulator_set_load operations
 - icc_level configuration in device

However "min_uA" field is not used anywhere, thus we can remove it.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The rc variable is not needed in bnx2fc_abts_cleanup(). Remove it and
just return SUCCESS.

[mkp: commit desc]
Signed-off-by: Ding Xiang <dingxiang@cmss.chinamobile.com>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

 - Update the driver version.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

 - lport was getting used without initialization, initialize it to fix a
   warning.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

 - Handle refcount of rdata during error conditions.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Here is the relevant logs for the problem we are solving:

qedf_flush_active_ios:1707]:3: Flush active i/o's num=0x17 fcport=0xffff948168fbcc80 port_id=0x550200 scsi_id=0.
qedf_flush_active_ios:1708]:3: Locking flush mutex.
qedf_flush_active_ios:1758]:3: Not outstanding, xid=0xaaf, cmd_type=3 refcount=1.
qedf_flush_active_ios:1896]:3: Flushed 0x16 I/Os, active=0x1.
qedf_flush_active_ios:1901]:3: Flushed 0x16 I/Os, active=0x1 cnt=60.
qedf_send_rrq:295]:3: Sending RRQ orig io = ffffb48b8f7d7158, orig_xid = 0xaaf
qedf_initiate_els:37]:3: Sending ELS
qedf_initiate_els:68]:3: initiate_els els_req = 0xffffb48b8f6d3098 cb_arg = ffff948fd5e4de80 xid = 4c6
qedf_init_mp_req:2172]:3: Entered.
qedf_init_mp_task:727]:3: Initializing MP task for cmd_type=4
qedf_initiate_els:134]:3: Ringing doorbell for ELS req
qedf_flush_active_ios:1901]:3: Flushed 0x16 I/Os, active=0x2 cnt=20.
qedf_cmd_timeout:96]:3: ELS timeout, xid=0x4c6.
qedf_rrq_compl:186]:3: Entered.
qedf_rrq_compl:204]:3: rrq_compl: orig io = ffffb48b8f7d7158, orig xid = 0xaaf, rrq_xid = 0x4c6, refcount=1
qedf_flush_active_ios:1935]:3: Unlocking flush mutex.
qedf_upload_connection:1579]:3: Uploading connection port_id=550200.

We found an ABTS command for which CMD_OUTSTANDING was cleared (line 3).
For this command, delayed send_rrq was queued, but would take 10 secs to
execute.  Adding capability to detect that (based on io_req->state that is
being introduced), and attempt to cancel rrq_work. If we succeed, we drop
the reference and free the io_req. If we cannot, then the els will get sent
out and we will wait for 10 secs for it to complete.
Signed-off-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

cmd_type is over written to QEDF_CLEANUP during cleanup, so check for
tm_flags.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

 - The flag will help in to figure out if io_req is cleaned or not.
Signed-off-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

 - Command is already completed with underrun so no need to send ABTS.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

 - I/Os, aborts and tmf should not be queued if flush is in progress.
Signed-off-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

 - Check proper values before servicing CVL.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The fc_rport_priv structure is reference counted, so we need to ensure that
the reference is increased before accessing the structure.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

On completions where we do not have a bad scsi_cmnd pointer we should
return before the the label lest we do a double kref_put.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

 - Wait for all the connections to get uploaded.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

 - Check the validity of various pointers before processing.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

test_bit() is atomic, test_bit() || test_bit() is not. So protect
consecutive bit tests with a lock to avoid races.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

fc_rport_create() needs to be called with disc_mutex held.  And we should
re-assign the 'rdata' pointer in case it got changed.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

qedf_xmit() calls fc_rport_lookup(), but discards the returned rdata
structure almost immediately without decreasing the refcount.  This leads
to a refcount leak and the rdata never to be freed.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

 - Check if link is UP before sending and processing any packets on wire.
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

When receiving an unsolicited frame we could crash on a list traversal in
fc_rport_lookup while searching the rport which is associated with our
lport.

Initialize the lport's discovery node after allocating the lport in
__qedf_probe().
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

 - Correct memory barriers to make sure all cmnds are flushed.
Signed-off-by: Andrew Vasquez <andrewv@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

 - If a TMF and cleanup are issued at the same time they could cause a call
   trace if issued against the same xid as the io_req->tm_done completion
   is used for both.

 - Set and clear cleanup bit in cleanup routine.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

An I/O can be in any state when flush is called, it can be in abort,
waiting for abort, RRQ send and waiting or TMF send.

 - HZ can be different on different architecture, correctly set abort
   timeout value.

 - Flush can complete the I/Os prematurely, handle refcount for aborted
   I/Os and for which RRQ is pending.

 - Differentiate LUN/TARGET reset, as cleanup needs to be send to firmware
   accordingly.

 - Add flush mutex to sync cleanup call from abort and flush routine.

 - Clear abort/outstanding bit on timeout.
Signed-off-by: Shyam Sundar <shyam.sundar@marvell.com>
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The purpose of flush routine is to cleanup I/Os to the firmware and
complete them to scsi middle layer. This routine is invoked before
connection is uploaded because of rport going away.

 - Don't process any I/Os, aborts, TMFs coming when flush in progress.

 - Add flags to handle cleanup and release of I/Os because flush can
   prematurely complete I/Os.

 - Original command can get completed to driver when cleanup for same is
   posted to firmware, handle this condition.

 - Modify flush to handle I/Os in all the states like abort, TMF, RRQ and
   timeouts.
Signed-off-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

When mapping the pages from a scatter/gather list from the SCSI layer we
only need to follow these rules:

 - Max SGEs for each I/O request is 256
 - No size limit on each SGE
 - No need to split OS provided SGEs to 4K before sending to firmware.
 - Slow SGE is applicable only when:
   - There are > 8 SGEs and any middle SGE is less than a page size (4K)

Make necessary changes so that driver follows these rules. Applicable only
for Write requests (not for Read requests). No need to check SGE address
alignment requirements (first, middle or last) before declaring slow SGE.
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Fixes the following crash as the return was missing from the check if an
fcport is offloaded. If we hit this code we continue to try to post an
invalid task which can lead to the crash:

[30259.616411] [0000:61:00.3]:[qedf_post_io_req:989]:3: Session not offloaded yet.
[30259.616413] [0000:61:00.3]:[qedf_upload_connection:1340]:3: Uploading connection port_id=490020.
[30259.623769] BUG: unable to handle kernel NULL pointer dereference at 0000000000000198
[30259.631645] IP: [<ffffffffc035b1ed>] qedf_init_task.isra.16+0x3d/0x450 [qedf]
[30259.638816] PGD 0
[30259.640841] Oops: 0000 [#1] SMP
[30259.644098] Modules linked in: fuse xt_CHECKSUM iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack ipt_REJECT nf_reject_ipv4 tun bridge stp llc ebtable_filter ebtables devlink ip6table_filter ip6_tables iptable_filter vfat fat ib_isert iscsi_target_mod ib_srpt target_core_mod ib_srp scsi_transport_srp ib_ipoib ib_ucm ib_umad dm_service_time skx_edac intel_powerclamp coretemp intel_rapl iosf_mbi kvm_intel kvm irqbypass crc32_pclmul ghash_clmulni_intel aesni_intel rpcrdma sunrpc rdma_ucm ib_uverbs lrw gf128mul ib_iser rdma_cm iw_cm ib_cm libiscsi scsi_transport_iscsi qedr(OE) glue_helper ablk_helper cryptd ib_core dm_round_robin joydev pcspkr ipmi_ssif ses enclosure ipmi_si ipmi_devintf ipmi_msghandler mei_me
[30259.715529]  mei sg hpilo hpwdt shpchp wmi lpc_ich acpi_power_meter dm_multipath ip_tables xfs libcrc32c sd_mod crc_t10dif crct10dif_generic uas usb_storage mgag200 qedf(OE) i2c_algo_bit libfcoe drm_kms_helper libfc syscopyarea sysfillrect scsi_transport_fc qede(OE) sysimgblt fb_sys_fops ptp ttm pps_core drm qed(OE) smartpqi crct10dif_pclmul crct10dif_common crc32c_intel i2c_core scsi_transport_sas scsi_tgt dm_mirror dm_region_hash dm_log dm_mod
[30259.754237] CPU: 9 PID: 977 Comm: kdmwork-253:7 Kdump: loaded Tainted: G        W  OE  ------------   3.10.0-862.el7.x86_64 #1
[30259.765664] Hardware name: HPE Synergy 480 Gen10/Synergy 480 Gen10 Compute Module, BIOS I42 04/04/2018
[30259.775000] task: ffff8c801efd0000 ti: ffff8c801efd8000 task.ti: ffff8c801efd8000
[30259.782505] RIP: 0010:[<ffffffffc035b1ed>]  [<ffffffffc035b1ed>] qedf_init_task.isra.16+0x3d/0x450 [qedf]
[30259.792116] RSP: 0018:ffff8c801efdbbb0  EFLAGS: 00010046
[30259.797444] RAX: 0000000000000000 RBX: ffffa7f1450948d8 RCX: ffff8c7fe5bc40c8
[30259.804600] RDX: ffff8c800715b300 RSI: ffffa7f1450948d8 RDI: ffff8c80169c2480
[30259.811755] RBP: ffff8c801efdbc30 R08: 00000000000000ae R09: ffff8c800a314540
[30259.818911] R10: ffff8c7fe5bc40c8 R11: ffff8c801efdb8ae R12: 0000000000000000
[30259.826068] R13: ffff8c800715b300 R14: ffff8c80169c2480 R15: ffff8c8005da28e0
[30259.833223] FS:  0000000000000000(0000) GS:ffff8c803f840000(0000) knlGS:0000000000000000
[30259.841338] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[30259.847100] CR2: 0000000000000198 CR3: 000000081242e000 CR4: 00000000007607e0
[30259.854256] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[30259.861412] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[30259.868568] PKRU: 00000000
[30259.871278] Call Trace:
[30259.873737]  [<ffffffffc035c948>] qedf_post_io_req+0x148/0x680 [qedf]
[30259.880201]  [<ffffffffc035d070>] qedf_queuecommand+0x1f0/0x240 [qedf]
[30259.886749]  [<ffffffffa329b050>] scsi_dispatch_cmd+0xb0/0x240
[30259.892600]  [<ffffffffa32a45bc>] scsi_request_fn+0x4cc/0x680
[30259.898364]  [<ffffffffa3118ad9>] __blk_run_queue+0x39/0x50
[30259.903954]  [<ffffffffa3114393>] __elv_add_request+0xd3/0x260
[30259.909805]  [<ffffffffa311baf0>] blk_insert_cloned_request+0xf0/0x1b0
[30259.916358]  [<ffffffffc010b622>] map_request+0x142/0x220 [dm_mod]
[30259.922560]  [<ffffffffc010b716>] map_tio_request+0x16/0x40 [dm_mod]
[30259.928932]  [<ffffffffa2ebb1f5>] kthread_worker_fn+0x85/0x180
[30259.934782]  [<ffffffffa2ebb170>] ? kthread_stop+0xf0/0xf0
[30259.940284]  [<ffffffffa2ebae31>] kthread+0xd1/0xe0
[30259.945176]  [<ffffffffa2ebad60>] ? insert_kthread_work+0x40/0x40
[30259.951290]  [<ffffffffa351f61d>] ret_from_fork_nospec_begin+0x7/0x21
[30259.957750]  [<ffffffffa2ebad60>] ? insert_kthread_work+0x40/0x40
[30259.963860] Code: fe 41 55 49 89 d5 41 54 53 48 89 f3 48 83 ec 58 4c 8b 67 28 4c 8b 4e 18 65 48 8b 04 25 28 00 00 00 48 89 45 d0 31 c0 4c 8b 7e 58 <49> 8b 84 24 98 01 00 00 48 8b 00 f6 80 31 01 00 00 10 0f 85 0b
[30259.983372] RIP  [<ffffffffc035b1ed>] qedf_init_task.isra.16+0x3d/0x450 [qedf]
[30259.990630]  RSP <ffff8c801efdbbb0>
[30259.994127] CR2: 0000000000000198
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

There is currently an overlap where exchange IDs between what is used for
offloaded commands and by libfc for ELS commands.  Correct this so that
exchange ID range is:

Offloaded requests: 0 to 0xfff
libfc requests: 0x1000 to 0xfffe
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

If we cannot allocate an ELS middlepath request, simply fail instead of
trying to delay and then reallocate.  This delay logic is causing soft
lockup messages:

NMI watchdog: BUG: soft lockup - CPU#2 stuck for 22s! [kworker/2:1:7639]
Modules linked in: xt_CHECKSUM ipt_MASQUERADE nf_nat_masquerade_ipv4 tun devlink ip6t_rpfilter ipt_REJECT nf_reject_ipv4 ip6t_REJECT nf_reject_ipv6 xt_conntrack ip_set nfnetlink ebtable_nat ebtable_broute bridge stp llc ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw ebtable_filter ebtables ip6table_filter ip6_tables iptable_filter dm_service_time vfat fat rpcrdma sunrpc ib_isert iscsi_target_mod ib_iser libiscsi scsi_transport_iscsi ib_srpt target_core_mod ib_srp scsi_transport_srp ib_ipoib rdma_ucm ib_ucm ib_uverbs ib_umad rdma_cm ib_cm iw_cm sb_edac intel_powerclamp coretemp intel_rapl iosf_mbi kvm_intel kvm
irqbypass crc32_pclmul ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd iTCO_wdt iTCO_vendor_support qedr(OE) ib_core joydev ipmi_ssif pcspkr hpilo hpwdt sg ipmi_si ipmi_devintf ipmi_msghandler ioatdma shpchp lpc_ich wmi dca acpi_power_meter dm_multipath ip_tables xfs libcrc32c sd_mod crc_t10dif crct10dif_generic qedf(OE) libfcoe mgag200 libfc i2c_algo_bit drm_kms_helper scsi_transport_fc qede(OE) syscopyarea sysfillrect sysimgblt fb_sys_fops ttm qed(OE) drm crct10dif_pclmul e1000e crct10dif_common crc32c_intel scsi_tgt hpsa i2c_core ptp scsi_transport_sas pps_core dm_mirror dm_region_hash dm_log dm_mod
CPU: 2 PID: 7639 Comm: kworker/2:1 Kdump: loaded Tainted: G           OEL ------------   3.10.0-861.el7.x86_64 #1
Hardware name: HP ProLiant DL580 Gen9/ProLiant DL580 Gen9, BIOS U17 07/21/2016
Workqueue: qedf_2_dpc qedf_handle_rrq [qedf]
task: ffff959edd628fd0 ti: ffff959ed6f08000 task.ti: ffff959ed6f08000
RIP: 0010:[<ffffffff8355913a>]  [<ffffffff8355913a>] delay_tsc+0x3a/0x60
RSP: 0018:ffff959ed6f0bd30  EFLAGS: 00000246
RAX: 000000008ef5f791 RBX: 5f646d635f666465 RCX: 0000025b8ededa2f
RDX: 000000000000025b RSI: 0000000000000002 RDI: 0000000000217d1e
RBP: ffff959ed6f0bd30 R08: ffffffffc079aae8 R09: 0000000000000200
R10: ffffffffc07952c6 R11: 0000000000000000 R12: 6c6c615f66646571
R13: ffff959ed6f0bcc8 R14: ffff959ed6f0bd08 R15: ffff959e00000028
FS:  0000000000000000(0000) GS:ffff959eff480000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f4117fa1eb0 CR3: 0000002039e66000 CR4: 00000000003607e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
[<ffffffff8355907d>] __const_udelay+0x2d/0x30
[<ffffffffc079444a>] qedf_initiate_els+0x13a/0x450 [qedf]
[<ffffffffc0794210>] ? qedf_srr_compl+0x2a0/0x2a0 [qedf]
[<ffffffffc0795337>] qedf_send_rrq+0x127/0x230 [qedf]
[<ffffffffc078ed55>] qedf_handle_rrq+0x15/0x20 [qedf]
[<ffffffff832b2dff>] process_one_work+0x17f/0x440
[<ffffffff832b3ac6>] worker_thread+0x126/0x3c0
[<ffffffff832b39a0>] ? manage_workers.isra.24+0x2a0/0x2a0
[<ffffffff832bae31>] kthread+0xd1/0xe0
[<ffffffff832bad60>] ? insert_kthread_work+0x40/0x40
[<ffffffff8391f637>] ret_from_fork_nospec_begin+0x21/0x21
[<ffffffff832bad60>] ? insert_kthread_work+0x40/0x40
Signed-off-by: Chad Dupuis <cdupuis@marvell.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Clang warns when it sees a logical not on the left side of a conditional
statement because it thinks the logical not should be applied to the whole
statement, not just the left side:

drivers/scsi/qla2xxx/qla_nx.c:3703:7: warning: logical not is only
applied to the left hand side of this comparison
[-Wlogical-not-parentheses]

This particular instance was already fixed by commit 0bfe7d3c ("scsi:
qla2xxx: Simplify conditional check") upstream but it was reintroduced by
commit 3695310e ("scsi: qla2xxx: Update flash read/write routine") in
the 5.2/scsi-queue.

Fixes: 3695310e ("scsi: qla2xxx: Update flash read/write routine")
Link: https://github.com/ClangBuiltLinux/linux/issues/80Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Make sd_probe() easier to read by inlining sd_probe_part2(). This patch
does not change any functionality.

Cc: Lee Duncan <lduncan@suse.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

As explained during the 2018 LSF/MM session about increasing SCSI disk
probing concurrency, the problems with the current probing approach are as
follows:

- The driver core is unaware of asynchronous SCSI LUN probing.
  wait_for_device_probe() waits for all asynchronous probes except
  asynchronous SCSI disk probes.

- There is unnecessary serialization between sd_probe() and sd_remove().
  This can lead to a deadlock.

Hence this patch that modifies the sd driver such that it uses the driver
core framework for asynchronous probing. The async domains and
get_device()/put_device() pairs that became superfluous due to this change
are removed.

This patch does not affect the time needed for loading the scsi_debug
kernel module with parameters delay=0 and max_luns=256.

This patch depends on commit ef0ff683 ("driver core: Probe devices
asynchronously instead of the driver") that went upstream in kernel version
v5.1-rc1.

Cc: Lee Duncan <lduncan@suse.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

There are a couple of statements that are incorrectly indented, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The variable len is not being inintialized and the uninitialized value is
being returned. However, this return path is never reached because the
default case in the switch statement returns -ENOSYS.  Clean up the code by
replacing the return -ENOSYS with a break for the default case and
returning -ENOSYS at the end of the function.  This allows len to be
removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Reducing the count should be alua_tg_pt_gps_count instead of
alua_tg_pt_gps_counter when free alua group.
Signed-off-by: tangwenji <tang.wenji@zte.com.cn>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

When building with -Wsometimes-uninitialized, Clang warns:

drivers/scsi/gdth.c:3662:6: warning: variable 'paddr' is used
uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]

Don't attempt to call dma_free_coherent when buf is NULL (meaning that
we never called dma_alloc_coherent and initialized paddr), which avoids
this warning.

Link: https://github.com/ClangBuiltLinux/linux/issues/402Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/scsi/pm8001/pm8001_hwi.c: In function 'mpi_smp_completion':
drivers/scsi/pm8001/pm8001_hwi.c:2901:6: warning:
 variable 'param' set but not used [-Wunused-but-set-variable]

drivers/scsi/pm8001/pm8001_hwi.c: In function 'pm8001_bytes_dmaed':
drivers/scsi/pm8001/pm8001_hwi.c:3247:24: warning:
 variable 'sas_ha' set but not used [-Wunused-but-set-variable]

They're never used since introduction, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>