- 16 Oct, 2007 40 commits
-
-
Krzysztof Helt authored
This patch: - initializes correctly the Permedia2V chip if it is not initialized by BIOS - puts back clock frequency for the ELSA WINNER board to 100kHz - fixes returned error values from setcolreg() function - uses more general classes for PCI ids Signed-off-by:
Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by:
Antonino Daplas <adaplas@gmail.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Krzysztof Helt authored
This patch concentrates on source compacting, simplification and more conformance to kernel coding standards. The major changes: - RD32() and WR() functions are merged into pm2_RD() and pm2_WR() - conditional (with switch()) RDAC functions are separated in two unconditional ones - the conditional pm2fb_block_op() function is merged into pm2fb_fillrect() and pm2fb_copyarea() - WAIT_FIFO() values are corrected Signed-off-by:
-
Krzysztof Helt authored
This patch adds accelerated imageblit function. Signed-off-by:
-
Krzysztof Helt authored
This patch adds usage of MTRR registers and two new options: noaccel and nomtrr. [bunk@kernel.org: make pm3fb_init() static again] Signed-off-by:
-
Krzysztof Helt authored
This patch contains improvements: - it adds ROP_XOR in pm3fb_fillrect() - it conforms closer to coding style - it removes redundant parentheses and setting bits with 0 value - it checks if hardware acceleration is disabled in pm3fb_imageblit - it adds module description Signed-off-by:
-
Krzysztof Helt authored
This patch contains 3 small improvements: - it corrects scan line width calculation in pm3fb_imageblit() - it corrects mmio mapping for big endian machines - it enables panning acceleration constants Signed-off-by:
-
Krzysztof Helt authored
This patch removes the pm3_imageblit() restriction to blit only images with width divisable by 32. Signed-off-by:
-
Krzysztof Helt authored
This patch removes constants named AAA_DISABLE with value 0. They are redudant and misleading ( a |= AAA_DISABLE does nothing and usually should be a &= ~AAA_ENABLE). Signed-off-by:
-
Krzysztof Helt authored
This patch corrects name of the field. Signed-off-by:
-
Krzysztof Helt authored
This patch adds accelerated copyarea and partially accelerated imageblit functions. There is also fixed one register address in the pm3fb.h file. Signed-off-by:
-
Michal Januszewski authored
Documentation for the uvesafb driver. Signed-off-by:
Michal Januszewski <spock@gentoo.org> Signed-off-by:
-
Michal Januszewski authored
uvesafb is an enhanced version of vesafb. It uses a userspace helper (v86d) to execute calls to the x86 Video BIOS functions. The driver is not limited to any specific arch and whether it works on a given arch or not depends on that arch being supported by the userspace daemon. It has been tested on x86_32 and x86_64. A single BIOS call is represented by an instance of the uvesafb_ktask structure. This structure contains a buffer, a completion struct and a uvesafb_task substructure, containing the values of the x86 registers, a flags field and a field indicating the length of the buffer. Whenever a BIOS call is made in the driver, uvesafb_exec() builds a message using the uvesafb_task substructure and the contents of the buffer. This message is then assigned a random ack number and sent to the userspace daemon using the connector interface. The message's sequence number is used as an index for the uvfb_tasks array, which provides a mapping from the messages coming from userspace to the in-kernel uvesafb_ktask structs. The userspace daemon performs the requested operation and sends a reply in the form of a uvesafb_task struct and, optionally, a buffer. The seq and ack numbers in the reply should be exactly the same as those in the request. Each message from userspace is processed by uvesafb_cn_callback() and after passing a few sanity checks leads to the completion of a BIOS call request. Signed-off-by:
-
Michal Januszewski authored
Add connector idx and val constants for v86d and uvesafb. Signed-off-by:
-
Michal Januszewski authored
Change the maximum message size to 16k to allow transfers of VBE data blocks from userspace. Signed-off-by:
-
Michal Januszewski authored
Make fb_destroy_modelist an exported symbol for use in the uvesafb driver. Signed-off-by:
-
Bryan Kadzban authored
drivers/char/rtc.c allowed RTC_PIE_ON ioctls for non-root users, as long as the current interval (set via RTC_IRQP_SET) is <= max_user_freq. Allow RTC_PIE_ON under the same conditions when /dev/rtc* is handled by the rtc subsystem. Signed-off-by:
Bryan Kadzban <bryan@kdzbn.homelinux.net> Acked-by:
Alessandro Zummo <alessandro.zummo@towertech.it> Cc: David Brownell <david-b@pacbell.net> Signed-off-by:
-
Bryan Kadzban authored
drivers/char/rtc.c exposed a sysctl to change the maximum frequency at which a non-root user could ask the RTC to generate interrupts (via the RTC_IRQP_SET ioctl). This value is no longer available under the new RTC subsystem, so add it to sysfs for each RTC device. Works for me on x86_64 (both reads and writes), using rtc-cmos. Signed-off-by:
Alessandro Zummo <a.zummo@towertech.it> Cc: David Brownell <david-b@pacbell.net> Signed-off-by:
-
David Brownell authored
Some cleanups for the rtc-cmos probe logic: - Claim i/o ports with request_region() not request_resource(), for better coexistence betwen platform and pnp bus glues. - Claim those ports earlier, to help work around procfs bugs (it allows duplicate names, like /proc/driver/rtc). - Fix some glitches in cleanup code, notably a cut'n'paste-o where the i/o port region might not get released during cleanup after a probe fault. And some comment clarifications, including noting that this code must work with PNPBIOS not just PNPACPI.. [akpm@linux-foundation.org: coding-style fixes] Signed-off-by:
David Brownell <dbrownell@users.sourceforge.net> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by:
-
Mark Lord authored
Fix readback of RTC alarms on platforms which return -1 in non-hardware-supported RTC alarm fields. To fill in the missing (-1) values, we grab an RTC timestamp along with the RTC alarm value, and use the timestamp fields to populate the missing alarm fields. To counter field-wrap races (since the timestamp and alarm are not read together atomically), we read the RTC timestamp both before and after reading the RTC alarm value, and then check for wrapped fields --> if any have wrapped, we know we have a possible inconsistency, so we loop and reread the timestamp and alarm again. Wrapped fields in the RTC timestamps are an issue because rtc-cmos.c, for example, also gets/uses an RTC timestamp internally while fetching the RTC alarm. If our timestamp here wasn't the same (minutes and higher) as what was used internally there, then we might end up populating the -1 fields with inconsistent values. This fixes readbacks from /sys/class/rtc/rtc?/wakealarm, as well as other code paths which call rtc_read_alarm(). Signed-off-by:
Mark Lord <mlord@pobox.com> Cc: David Brownell <david-b@pacbell.net> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by:
-
Scott Wood authored
This patch adds an RTC class driver for the Maxim/Dallas 1374 RTC chip, based on drivers/i2c/chips/ds1374.c. It supports alarm functionality. Signed-off-by:
Scott Wood <scottwood@freescale.com> Acked-by:
-
Jean Delvare authored
Not all i2c adapters support I2C-level messaging. Check that the adapter does before probing for a PCF8583 chip, as the driver makes use of i2c_transfer and i2c_master_send. Signed-off-by:
Jean Delvare <khali@linux-fr.org> Signed-off-by:
-
Atsushi Nemoto authored
The rtc-ds1742 platform driver name doesn't match its module name, which might prevents it from properly hotplugging. There is only two in-tree user of its driver, which are fixed by this patch too. Signed-off-by:
Atsushi Nemoto <anemo@mba.ocn.ne.jp> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: David Brownell <david-b@pacbell.net> Cc: Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Atsushi Nemoto authored
The rtc-ds1553 platform driver name doesn't match its module name, which might prevent it from properly hotplugging. This driver has no in-tree users. Signed-off-by:
-
Mark Zhan authored
In rtc-dev.c, when a rtc device is opened, file->private_data is already attached with the rtc device pointer, so there is no need to call to_rtc_device() to convert file->private_data to a rtc device pointer. Acked-by:
Mark Zhan <rongkai.zhan@windriver.com> Signed-off-by:
-
David Brownell authored
RTC periodic IRQs are only defined to work for 2^N Hz values. This patch moves that validity check into the infrastructure, so drivers don't need to check it; and adds kerneldoc for the two interface functions related to periodic IRQs. (One of which was quite mysterious until its first use was recently checked in!) Signed-off-by:
-
Alessandro Zummo authored
Add kernel/kernel and kernel/user locking for the periodic irq feature of the rtc class. PIE ioctls are also supported. Signed-off-by:
-
Michael Halcrow authored
The functions that eventually call down to ecryptfs_read_lower(), ecryptfs_decrypt_page(), and ecryptfs_copy_up_encrypted_with_header() should have the responsibility of managing the page Uptodate status. This patch gets rid of some of the ugliness that resulted from trying to push some of the page flag setting too far down the stack. Signed-off-by:
Michael Halcrow <mhalcrow@us.ibm.com> Signed-off-by:
-
Michael Halcrow authored
Replace some magic numbers with sizeof() equivalents. Signed-off-by:
-
Michael Halcrow authored
The switch to read_write.c routines and the persistent file make a number of functions unnecessary. This patch removes them. Signed-off-by:
-
Michael Halcrow authored
Initialize persistent lower file on inode create. Signed-off-by:
-
Michael Halcrow authored
Update data types and add casts in order to avoid potential overflow issues. Signed-off-by:
-
Michael Halcrow authored
Convert readpage, prepare_write, and commit_write to use read_write.c routines. Remove sync_page; I cannot think of a good reason for implementing that in eCryptfs. Signed-off-by:
-
Michael Halcrow authored
Rather than open a new lower file for every eCryptfs file that is opened, truncated, or setattr'd, instead use the existing lower persistent file for the eCryptfs inode. Change truncate to use read_write.c functions. Change ecryptfs_getxattr() to use the common ecryptfs_getxattr_lower() function. Signed-off-by:
-
Michael Halcrow authored
Update the metadata read/write functions and grow_file() to use the read_write.c routines. Do not open another lower file; use the persistent lower file instead. Provide a separate function for crypto.c::ecryptfs_read_xattr_region() to get to the lower xattr without having to go through the eCryptfs getxattr. Signed-off-by:
-
Michael Halcrow authored
This patch sets up and destroys the persistent lower file for each eCryptfs inode. Signed-off-by:
-
Michael Halcrow authored
Replace page encryption and decryption routines and inode size write routine with versions that utilize the read_write.c functions. Signed-off-by:
-
Michael Halcrow authored
Add a set of functions through which all I/O to lower files is consolidated. This patch adds a new inode_info reference to a persistent lower file for each eCryptfs inode; another patch later in this series will set that up. This persistent lower file is what the read_write.c functions use to call vfs_read() and vfs_write() on the lower filesystem, so even when reads and writes come in through aops->readpage and aops->writepage, we can satisfy them without resorting to direct access to the lower inode's address space. Several function declarations are going to be changing with this patchset. For now, in order to keep from breaking the build, I am putting dummy parameters in for those functions. Signed-off-by:
-
Michael Halcrow authored
The error paths and the module exit code need work. sysfs unregistration is not the right place to tear down the crypto subsystem, and the code to undo subsystem initializations on various error paths is unnecessarily duplicated. This patch addresses those issues. Signed-off-by:
-
Michael Halcrow authored
Remove assignments in if-statements. Signed-off-by:
-
Michael Halcrow authored
There is no point to keeping a separate header_extent_size and an extent_size. The total size of the header can always be represented as some multiple of the regular data extent size. [randy.dunlap@oracle.com: ecryptfs: fix printk format warning] Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
