- 29 Jan, 2015 8 commits
-
-
Antonio Ospite authored
Signed-off-by:
Antonio Ospite <ao2@ao2.it> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-
Hans Verkuil authored
If start_streaming fails, then the buffers must be given back to vb2 with state QUEUED, not ERROR. Otherwise a WARN_ON will be generated. In the disconnect it is pointless to call pwc_cleanup_queued_bufs() as stop_streaming() will be called anyway. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Tested-by:
-
Hans de Goede authored
Add support for the larger fifo found on sun5i and sun6i, having a separate compatible for the ir found on sun5i & sun6i also is useful if we ever want to add ir transmit support, because the sun5i & sun6i version do not have transmit support. Note this commits also adds checking for the end-of-packet interrupt flag (which was already enabled), as the fifo-data-available interrupt flag only gets set when the trigger-level is exceeded. So far we've been getting away with not doing this because of the low trigger-level, but this is something which we should have done since day one. Signed-off-by:
Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by:
-
Hans de Goede authored
On sun6i the cir block is attached to the reset controller, add support for de-asserting the reset if a reset controller is specified in dt. Signed-off-by:
-
Mauro Carvalho Chehab authored
Checkpatch complained about a few issues, like FSF address. Also, multi-line comments are not following the Kernel CodingStyle. While not too late, let's fix those issues. Cc: John McMaster <johndmcmaster@gmail.com> Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: -
John McMaster authored
Adds support for AmScope MU800 / ToupTek UCMOS08000KPB USB microscope camera. Signed-off-by:
John McMaster <johndmcmaster@gmail.com> Signed-off-by:
-
Hans Verkuil authored
When converting to or from Y'CbCr and R'G'B' the Y offset depends on the quantization range: it's 0 for full and 16 for limited range. But in the code it was hardcoded to 16. This messed up the brightness of the generated pattern. Signed-off-by:
-
Sakari Ailus authored
of_read_number() is defined in of.h but does not return an error code, so that non-of implementation could simply return an error. Temporarily work around this until of_read_number() can be replaced by of_property_read_u64_array(). Signed-off-by:
Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by:
-
- 27 Jan, 2015 32 commits
-
-
Antti Palosaari authored
We must unregister frontend first and after that driver itself. That order went wrong after demod drivers were switched to kernel I2C drivers, causing crashes. Tested-by:
Benjamin Larsson <benjamin@southpole.se> Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Antti Palosaari authored
As rtl2832 driver support now I2C binding we will switch to that one. Tested-by:
-
Antti Palosaari authored
Convert that driver to I2C driver model. Legacy DVB binding is left also for later removal... Tested-by:
-
Laurent Pinchart authored
This reverts commit 18661234. The video_device debug field has been renamed to dev_debug, resulting in a compilation failure. As v4l2 debugging is supposed to be controlled through a sysfs attribute created by the v4l2 core, there's no need to duplicate debug control through a module parameter. Remove it. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by:
-
Fabian Frederick authored
Based on versioncheck. Signed-off-by:
Fabian Frederick <fabf@skynet.be> Signed-off-by:
-
Aviv Greenberg authored
The UVC spec is a bit vague wrt devices using bulk endpoints, specifically, how to signal to a device to start streaming. For devices using isoc endpoints, the sequence for start streaming is: 1) The host sends PROBE_CONTROL(SET_CUR) PROBE_CONTROL(GET_CUR) 2) Host selects desired config and calls COMMIT_CONTROL(SET_CUR) 3) Host selects an alt interface other then zero - e.g SELECT_ALTERNATE_INTERFACE(1) 4) The device starts streaming However for devices using bulk endpoints, there must be *no* alt interface other than setting zero. From the UVC spec: "A VideoStreaming interface containing a bulk endpoint for streaming shall support only alternate setting zero. Additional alternate settings containing bulk endpoints are not permitted in a device that is compliant with the Video Class specification." So for devices using bulk endpoints, step #3 above is irrelevant, and thus cannot be used as an indication for the device to start streaming. So in practice, such devices start streaming immediately after a COMMIT_CONTROL(SET_CUR). In the uvc resume() handler, an unsolicited commit is sent, which causes devices using bulk endpoints to start streaming unintentionally. This patch modifies resume() handler to send a commit only if streaming needs to be reestablished, i.e if the device was actually streaming before is was suspended. Signed-off-by:
Aviv Greenberg <aviv.d.greenberg@intel.com> Signed-off-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Nobuhiro Iwamatsu authored
LNE bit in VI6_DISP_IRQ_STA register are from the 0 bit to 4 bit. This fixes bit position specified by VI6_DISP_IRQ_STA_LNE. Signed-off-by:
Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by:
-
Nobuhiro Iwamatsu authored
LNEE bit in VI6_DISP_IRQ_ENB register are from the 0 bit to 4 bit. This fixes bit position specified by VI6_DISP_IRQ_ENB_LNEE. Signed-off-by:
-
Takanari Hayama authored
According to the spec, the minimum input pixel size for BRU is 1px, not 4px. Signed-off-by:
Takanari Hayama <taki@igel.co.jp> Signed-off-by:
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by:
-
Martin Bugge authored
Use the new logging functions from the hdmi module. Signed-off-by:
Martin Bugge <marbugge@cisco.com> Signed-off-by:
-
Hans Verkuil authored
As per the suggestion of Thierry Reding rename HDMI_AUDIO_CODING_TYPE_EXT_STREAM to HDMI_AUDIO_CODING_TYPE_EXT_CT to be consistent with the CEA-861 spec. Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Martin Bugge authored
When receiving video it is very useful to be able to unpack the InfoFrames. Logging is useful as well, both for transmitters and receivers. Especially when implementing the VIDIOC_LOG_STATUS ioctl (supported by many V4L2 drivers) for a receiver it is important to be able to easily log what the InfoFrame contains. This greatly simplifies debugging. Signed-off-by:
-
Hans Verkuil authored
Add new Video InfoFrame colorspace information introduced in HDMI 2.0 and new Audio Coding Extension Types, also from HDMI 2.0. HDMI_CONTENT_TYPE_NONE was renamed to _GRAPHICS since that's what it is called in CEA-861-F. Signed-off-by:
-
Fabio Estevam authored
There is no need to jump to the 'err' label as we can simply return the error code directly and make the code shorter. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Acked-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
-
Dan Carpenter authored
The "i" variable is used as an offset into both the dev->vfd[] and the dev->devtype->vdevs[] arrays. The second array is smaller so we should use that as a limit instead of ARRAY_SIZE(dev->vfd). Also the original check was off by one. We should use a format string as well in case the ->name has any funny characters and also to stop static checkers from complaining. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Ondrej Zary authored
Improve g_tuner and add s_hw_freq_seek and enum_freq_bands support for cards with TEA575x radio. This allows signal/stereo detection and HW seek to work on these cards. Signed-off-by:
Ondrej Zary <linux@rainbow-software.org> Signed-off-by:
-
Ondrej Zary authored
Split ioctl interface from enum_freq_bands, g_tuner and s_hw_freq_seek functions and export them to be used in other drivers like bttv. Signed-off-by:
-
Ondrej Zary authored
Remove tea575x-specific code from bttv and use the common driver instead. Only set_frequency is implemented (signal/stereo detection or seek would require more changes to bttv). It works fine on Video Highway Xtreme (it actually makes the radio usable as it currently cannot be tuned properly). Miro/Pinnacle is untested but seems to be simple and should work. However, I don't understand the Terratec Active Radio Upgrade code. The HW seems to need IOR, IOW and CSEL signals that were taken from ISA bus on older cards (IOR and IOW directly and CSEL from some address decoder) and are emulated here using GPIOs. But the code manipulating these signals in bttv seems to be broken - it never asserts the IOR signal. If anyone has this HW, please test if I got that right. Signed-off-by:
-
Wolfram Sang authored
A few new i2c-drivers came into the kernel which clear the clientdata-pointer on exit or error. This is obsolete meanwhile, the core will do it. Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Rickard Strandqvist authored
Remove the function pvr2_hdw_cmd_powerdown() that is not used anywhere. This was partially found by using a static code analysis program called cppcheck. Signed-off-by:
Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se> Signed-off-by:
-
Rickard Strandqvist authored
Removes some functions that are not used anywhere: test_read() edid_read_block() dpp_write() dpp_read() esdp_write() esdp_read() cec_write_clr_set() This was partially found by using a static code analysis program called cppcheck. Signed-off-by:
-
Rickard Strandqvist authored
Remove the function vsp1_hsit_read() that is not used anywhere. This was partially found by using a static code analysis program called cppcheck. Signed-off-by:
-
Rickard Strandqvist authored
Remove the function saa7134_queue() that is not used anywhere. This was partially found by using a static code analysis program called cppcheck. Signed-off-by:
-
Rickard Strandqvist authored
Remove the function write_eeprom_byte() that is not used anywhere. This was partially found by using a static code analysis program called cppcheck. Signed-off-by:
-
Rickard Strandqvist authored
Removes some functions that are not used anywhere: vblanking() hblanking() This was partially found by using a static code analysis program called cppcheck. Signed-off-by:
-
Fabian Frederick authored
Based on versioncheck. Signed-off-by:
-
Fabian Frederick authored
Based on versioncheck. Signed-off-by:
-
Julia Lawall authored
Convert a call to init_timer and accompanying intializations of the timer's data and function fields to a call to setup_timer. A simplified version of the semantic match that fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression t,f,d; @@ -init_timer(&t); +setup_timer(&t,f,d); -t.data = d; -t.function = f; // </smpl> Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by:
-
Julia Lawall authored
Convert a call to init_timer and accompanying intializations of the timer's data and function fields to a call to setup_timer. A simplified version of the semantic match that fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression t,f,d; @@ -init_timer(&t); +setup_timer(&t,f,d); -t.data = d; -t.function = f; // </smpl> The semantic patch also changes the cast to long to a cast to unsigned long in the data initializer, as unsigned long is the type of the data field. Signed-off-by:
-
Julia Lawall authored
Convert a call to init_timer and accompanying intializations of the timer's data and function fields to a call to setup_timer. A simplified version of the semantic match that fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression t,f,d; @@ -init_timer(&t); +setup_timer(&t,f,d); -t.function = f; -t.data = d; // </smpl> Signed-off-by:
-
Julia Lawall authored
Convert a call to init_timer and accompanying intializations of the timer's data and function fields to a call to setup_timer. A simplified version of the semantic match that fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression t,f,d; @@ -t.function = f; -t.data = d; -init_timer(&t); +setup_timer(&t,f,d); // </smpl> Signed-off-by:
-
Ismael Luceno authored
s/uint8_t/u8/ Signed-off-by:
Ismael Luceno <ismael@iodev.co.uk> Signed-off-by:
-
