There are several problems with recent change to how IRQ's are setup.
   * synchronize_irq in sky2_shutdown would hang because there
     was no IRQ setup.
   * when device was set to down, some IRQ bits left enabled so a
     hardware error would produce IRQ with no handler
   * quick link on Optima chip set was enabled without handler
   * suspend/resume would leave IRQ on with no handler if device
     was down
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We are checking whether the MCR0_HASHEN bit is set using a logical and
instead of bitwise and, fix that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

My old email account at linux-foundation is no longer usable after
the LF breakin.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The first #include must be pch_gbe.h as it
does a #define of pr_fmt.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Re-request fw from fs may fail for different reasons, once the fw was
loaded we won't release it until driver is removed.

This also resolves the boot problem when initial fw is located on initrd,
but rootfs is still unavailable, in this case device reset will fail due
to absence of fw files.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

so the defconfig of the atmel continue to have the support of the network
as before
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bridge multicast snooping of ICMPv6 would incorrectly report a checksum problem
when used with Ethernet devices like sky2 that use CHECKSUM_COMPLETE.
When bytes are removed from skb, the computed checksum needs to be adjusted.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Martin Volf <martin.volf.42@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Patch avoids SIGA-r calls in case of SIGA-r required. It only calls
SIGA-r if a threshold of free buffer is reached. CPU consumption is
reduced as a consequence.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

when use dst_get_neighbour to get neighbour, we need
rcu_read_lock to protect, since dst_get_neighbour uses
rcu_dereference.
Signed-off-by: David S. Miller <davem@davemloft.net>

Invocation of dev_alloc_name() is re-inserted, because the created
net_device name is used to create the device name for the iucv bus.
This device is created before the register_netdev call.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch "qeth: exploit asynchronous delivery of storage blocks"
added a WARN_ON in qeth_schedule_recovery. A device recovery should
not cause a kernel warning. This is obviously a debugging  left-over
that we forgot to remove.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Without appropriate configuration at the SE, a HiperSockets device
cannot be used for sniffing. Setting the sniffer attribute is rejected
with -EPERM.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Kirby reported divides by zero errors in __tcp_select_window()

This happens when inet_csk_route_child_sock() returns a NULL pointer :

We free new socket while we eventually armed keepalive timer in
tcp_create_openreq_child()

Fix this by a call to tcp_clear_xmit_timers()

[ This is a followup to commit 918eb399 (net: add missing
bh_unlock_sock() calls) ]
Reported-by: Simon Kirby <sim@hostway.ca>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Simon Kirby <sim@hostway.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only update VERSION to reflect previous changes.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now works on Samsung Series 5 (chromebook)

Two fixes here:
o use 0x7F mask for phymode
o read phyid *AFTER* phy is powered up (via GPIOs)
Signed-off-by: Allan Chou <allan@asix.com.tw>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ax88772_reset takes about 2 seconds and is called twice.
Once from ax88772_bind() directly and again indirectly from usbnet_open().
Reset the USB FW/Phy enough to blink the LEDs when inserted.
Signed-off-by: Allan Chou <allan@asix.com.tw>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sometimes the phy isn't ready after reset...poll and pray it will be soon.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use correct value for rtl phy support.
(rtl phy are in AX88178 devices like NWU220G and USB2-ET1000).
Signed-off-by: Allan Chou <allan@asix.com.tw>
Tested-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Lantiq ETOP ethernet driver fails to build in 3.2-rc1 due to 2 missing
header files.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When HW doesn't remove FCS bytes they are reported in the completion
byte count, we don't need to take them to skb.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 3ceca749 added a TOS attribute.

Unfortunately TOS and TCLASS are both present in a dual-stack v6 socket,
furthermore they can have different values.  As such one cannot in a
sane way expose both through a single attribute.
Signed-off-by: Maciej Żenczyowski <maze@google.com>
CC: Murali Raja <muralira@google.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add checking for valid magic values (needed for stability in the event
corrupted packets are received) and remove some other unneeded checks.
Also, fix flagging device as WWAN (Bugzilla bug #39952).
Signed-off-by: Mark Kamichoff <prox@prolixium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Wait for the chip to be ready before any access to it. On the
Snowball platform we need to enable an external regulator before
the chip comes online, and then it happens that the device is
not yet ready at probe time, so let's wait for it.
Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

multicast_lock is taken in softirq context, so we should use
spin_lock_bh() in userspace.

call-chain in softirq context:
run_timer_softirq()
	br_multicast_query_expired()

call-chain in userspace:
sysfs_write_file()
	store_multicast_snooping()
		br_multicast_toggle()
Signed-off-by: Andrew Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 1c5cae81 removed an explicit call to dev_alloc_name in ip6_tnl_create
because register_netdevice will now create a valid name.  This works for the
net_device itself.

However the tunnel keeps a copy of the name in the parms structure for the
ip6_tnl associated with the tunnel.  parms.name is set by copying the net_device
name in ip6_tnl_dev_init_gen.  That function is called from ip6_tnl_dev_init in
ip6_tnl_create, but it is done before register_netdevice is called so the name
is set to a bogus value in the parms.name structure.

This shows up if you do a simple tunnel add, followed by a tunnel show:

[root@localhost ~]# ip -6 tunnel add remote fec0::100 local fec0::200
[root@localhost ~]# ip -6 tunnel show
ip6tnl0: ipv6/ipv6 remote :: local :: encaplimit 0 hoplimit 0 tclass 0x00 flowlabel 0x00000 (flowinfo 0x00000000)
ip6tnl%d: ipv6/ipv6 remote fec0::100 local fec0::200 encaplimit 4 hoplimit 64 tclass 0x00 flowlabel 0x00000 (flowinfo 0x00000000)
[root@localhost ~]#

Fix this by moving the strcpy out of ip6_tnl_dev_init_gen, and calling it after
register_netdevice has successfully returned.

Cc: stable@vger.kernel.org
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change makes sure that tx_packets/rx_bytes ifconfig counters are
updated even on NICs that don't provide hardware support for these
stats: they are now updated in software. For the sake of consistency,
we also now have tx_bytes updated in software (hardware counters
include ethernet CRC, and software doesn't account for it).

This reverts parts of:
 - "forcedeth: statistics optimization" (21828163)
 - "forcedeth: Improve stats counters" (0bdfea8b)
 - "forcedeth: remove unneeded stats updates" (4687f3f3)

Tested:
  pktgen + loopback (http://patchwork.ozlabs.org/patch/124698/)
  reports identical tx_packets/rx_packets and tx_bytes/rx_bytes.
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 1bc144b6 ("net, rds, Replace xlist in net/rds/xlist.h with
llist") added "select LLIST" to the RDS_RDMA Kconfig entry. But there is
no Kconfig symbol named LLIST. The select statement for that symbol is a
nop. Drop it.

lib/llist.o is builtin, so all that's needed to use the llist
functionality is to include linux/llist.h, which this commit also did.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>

We test for 'tx_ring' being != zero and BUG() if that's the case. So after
that check there is no way that 'tx_ring' could be anything _but_ zero, so
testing it again is just dead code. Once that dead code is removed, the
'pkc' local variable becomes entirely redundant, so remove that as well.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the ahash driver returns -EBUSY, AH4/6 input functions return
NET_XMIT_DROP, presumably copied from the output code path.  But
returning transmit codes on input doesn't make a lot of sense.
Since NET_XMIT_DROP is a positive int, this gets interpreted as
the next header type (i.e., success).  As that can only end badly,
remove the check.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

Firmware expects 'max_ssid_length' field in
'struct mwifiex_ie_types_wildcard_ssid_params' to be '0' for
performing SSID specific scan. Currently driver updates it with
an actual SSID length. Hence UUT is not able to find the AP
configured in hidden SSID mode in scan results and association
fails.

max_ssid_length is filled with '0' to fix the issue.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When HW RF kill switch is set to kill the radio, our NIC issues an
interrupt after we stop the APM module. When we unload the module,
the driver disables and cleans the interrupts before stopping the
APM. So we have a real interrupt (inta not zero) pending.
When this interrupts pops up the tasklet has already been killed
and we crash.

Here is a logical description of the flow:

disable and clean interrupts
synchronize interrupts
kill the tasklet

stop the APM <<== creates an RF kill interrupt

free_irq <<== somehow our ISR is called here and we crash

Here is the panic message:

[  201.313636] BUG: unable to handle kernel paging request at ffff8800911b7150
[  201.314541] IP: [<ffffffff8106d652>] tasklet_action+0x62/0x130
[  201.315149] PGD 1c06063 PUD db37f067 PMD db408067 PTE 80000000911b7160
[  201.316456] Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
[  201.317324] CPU 1
[  201.317495] Modules linked in: arc4 iwlwifi(-) mac80211 cfg80211 netconsole configfs binfmt_misc i915 drm_kms_helper drm uvcvideo i2c_algo_bit videodev dell_laptop dcdbas intel_agp dell_wmi intel_ips psmouse intel_gtt v4l2_compat_ioctl32 asix usbnet mii serio_raw video sparse_keymap firewire_ohci sdhci_pci sdhci firewire_core e1000e crc_itu_t [last unloaded: configfs]
[  201.323839]
[  201.324015] Pid: 2061, comm: modprobe Not tainted 3.1.0-rc9-wl #4 Dell Inc. Latitude E6410/0667CC
[  201.324736] RIP: 0010:[<ffffffff8106d652>]  [<ffffffff8106d652>] tasklet_action+0x62/0x130
[  201.325128] RSP: 0018:ffff88011bc43ea0  EFLAGS: 00010286
[  201.325338] RAX: ffff88008ae70000 RBX: ffff8800911b7150 RCX: ffff88008ae70028
[  201.325555] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff88008ae70000
[  201.325775] RBP: ffff88011bc43ec0 R08: 0000000000000000 R09: 0000000000000000
[  201.325994] R10: 0000000000000002 R11: 0000000000000001 R12: 0000000000000001
[  201.326212] R13: 0000000000000006 R14: 0000000000000100 R15: ffff88008e259fd8
[  201.326431] FS:  00007f4b90ea9700(0000) GS:ffff88011bc40000(0000) knlGS:0000000000000000
[  201.326657] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[  201.326864] CR2: ffff8800911b7150 CR3: 000000008fd6d000 CR4: 00000000000006e0
[  201.327083] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  201.327302] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[  201.327521] Process modprobe (pid: 2061, threadinfo ffff88008e258000, task ffff88008ae70000)
[  201.327747] Stack:
[  201.330494]  0000000000000046 0000000000000030 0000000000000001 0000000000000006
[  201.333870]  ffff88011bc43f30 ffffffff8106cd8a ffffffff811e1016 ffff88011bc43f08
[  201.337186]  0000000100000046 ffff88008e259fd8 0000000a10be2160 0000000000000006
[  201.340458] Call Trace:
[  201.342994]  <IRQ>
[  201.345656]  [<ffffffff8106cd8a>] __do_softirq+0xca/0x250
[  201.348185]  [<ffffffff811e1016>] ? pde_put+0x76/0x90
[  201.350730]  [<ffffffff8131aeae>] ? do_raw_spin_unlock+0x5e/0xb0
[  201.353261]  [<ffffffff811e1016>] ? pde_put+0x76/0x90
[  201.355776]  [<ffffffff8163ccfc>] call_softirq+0x1c/0x30
[  201.358287]  [<ffffffff8101531d>] do_softirq+0x9d/0xd0
[  201.360823]  [<ffffffff8106cb05>] irq_exit+0xd5/0xf0
[  201.363330]  [<ffffffff8163d5d6>] do_IRQ+0x66/0xe0
[  201.365819]  [<ffffffff81632673>] common_interrupt+0x73/0x73
[  201.368257]  <EOI>

Cc: <stable@kernel.org> 3.1+
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Change them over to plain "ETHERNET"
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When opt->srr_is_hit is set skb_rtable(skb) has been updated for
'nexthop' and iph->daddr should always equals to skb_rtable->rt_dst
holds, We need update iph->daddr either.
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The AH4/6 ahash input callbacks read out the nexthdr field from the AH
header *after* they overwrite that header.  This is obviously not going
to end well.  Fix it up.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The AH4/6 ahash output callbacks pass nexthdr to xfrm_output_resume
instead of the error code.  This appears to be a copy+paste error from
the input case, where nexthdr is expected.  This causes the driver to
continuously add AH headers to the datagram until either an allocation
fails and the packet is dropped or the ahash driver hits a synchronous
fallback and the resulting monstrosity is transmitted.

Correct this issue by simply passing the error code unadulterated.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit ff5a3b50 ("hippi: Move the HIPPI driver") moved the HIPPI
driver into drivers/net/hippi. It didn't source
drivers/net/hippi/Kconfig though, so it didn't make all necessary
Kconfig changes. So let drivers/net/kconfig source HIPPI's Kconfig file.

[ Fix syntax error at the end of HIPP's Kconfig file. -DaveM ]
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>