"mlock" should ideally only be used by the iio core. The mlock
implementation may change in the future which means that no driver
should be explicitly using mlock.
Signed-off-by: Rohit Sarkar <rohitsarkar5398@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add SEMTECH SX9310/9311 driver.

The device has the following entry points:

Usual frequency:
- sampling_frequency
- sampling_frequency_available

Instant reading of current values for different sensors:
- in_proximity0_raw
- in_proximity1_raw
- in_proximity2_raw
- in_proximity3_comb_raw
and associated events in events/
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enrico Granata <egranata@chromium.org>
Signed-off-by: Daniel Campello <campello@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Use devm_add_action_or_reset to automatically disable the device
when it is removed or an error occurs during probe routine.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

AD7091R is already supported by this driver. While AD7091R allows the
choice of an internal or an external voltage reference, for AD7091 the
reference is only provided by VDD. Since this information is anyway
obtained through the "vcc" regulator, no other driver changes are
required for adding AD7091 support as well.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

When CONVST signal is generated internally, IIO_CHAN_INFO_RAW can be
made available for AD7091R for single reads. This patch enables it and
makes supporting more devices by this driver easier.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Compared to the other supported parts, AD7091R are dependent of
a CONVST signal that initiates the conversion. At this moment, only
sampling in buffered mode is supported for AD7091R and the only
option until now was to generate this signal externally using an
IIO trigger. This patch adds the option of generating it internally,
more compatible triggers being available in this case.

Also, it is an intermediate step of adding support more devices.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

There is no need to call unaligned helpers on stack placed variables
because compiler will align them correctly, accordingly to architectural
ABI. Moreover, using bitwise type makes it explicit to see what we are
reading in bulk transfer. On top of that, use sizeof() instead of
magic value.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Explicit casting in printf() usually shows that something is not okay.
Here, we really don't need it by providing correct specifier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Device property API allows to gather device resources from different sources,
such as ACPI. Convert the drivers to unleash the power of device property API.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Use dev_get_platdata() to get the platform_data instead of
referencing it directly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

For easy grepping on debug purposes join string literals back in
the messages.

No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Explicit casting in printf() usually shows that something is not okay.
Here, we really don't need it by providing correct specifier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

In few places the unnecessary explicit castings are being used.
Drop them for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Use dev_get_platdata() to get the platform_data instead of
referencing it directly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Explicit casting in printf() usually shows that something is not okay.
Here, we really don't need it by providing correct specifier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit.  Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

It appears the author of the xilinx-xadc driver can't even spell his own
name correctly. Fix that.
Reported-by: Lars Möllendorf <lars.moellendorf@plating.de>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Function 'devm_gpiod_get_index_optional' returns NULL if the
descriptor is invalid and the error associated for the error
pointer is ENOENT. Sometimes if the pin is just assigned the
error associated for the pointer might not be ENOENT but other.
In order to avoid weirds behaviours if this happen set descriptor
to NULL in the driver port structure.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200320110123.9907-6-sergio.paracuellos@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We are using the counter to print the slot which has been
enabled. Use the correct associated slot for the port instead.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200320110123.9907-5-sergio.paracuellos@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In order to align work with the mt7621-pci-phy part of
the driver and device tree which is now using only two
real phys one of them dual ported properly parse the
device tree and don't call phy initialization for the
slot 1 because is being taking into account when the
phy for the slot 0 is instantiated.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200320110123.9907-4-sergio.paracuellos@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This soc has only two real pcie phys one of them
having a different register to enable and disable it.
Change this to have only two dt nodes for the phys and
use 'phy-cells' properly to say if the phy has dual ports.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200320110123.9907-3-sergio.paracuellos@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This soc has two phy's for the pcie one of them using just a different
register for settig it up but sharing all the rest of the config. Until
now we was presenting this schema as three different phy's in the device
tree using the 'phy-cells' node property to discriminate an index and
setting up a complete phy for the dual port index. This sometimes worked
properly but reconfiguring the same registers twice presents sometimes
some unstable pcie links and the ports was not properly being detected.
The problems only appears on hard resets and soft resets was properly
working. Instead of having this schema just set two phy's in the device
ree and use the 'phy-cells' property to say if the port has or not a dual
port. Doing this configuration and set up becomes easier, LOC is decreased
and the behaviour also gets deterministic with properly and stable pcie
links in both hard and soft resets.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200320110123.9907-2-sergio.paracuellos@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Correct long lines of comments to respect 80 character per line
limit and make them C89 style one.
Found using checkpatch.pl.
Signed-off-by: R Veera Kumar <vkor@vkten.in>
Link: https://lore.kernel.org/r/20200320024337.4754-1-vkor@vkten.inSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Correct typos in comments.
Misspellings found using checkpatch.pl.
Signed-off-by: R Veera Kumar <vkor@vkten.in>
Link: https://lore.kernel.org/r/46d4e7cd66ec8d5bf7445201e10e3d50fe1c618e.1584687545.git.vkor@vkten.inSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Correct multi-line comments as per coding style to respect
80 characters per line limit.

Amalgamate individual lines into single multiline comment.
Reorganize it for readability.
Signed-off-by: R Veera Kumar <vkor@vkten.in>
Link: https://lore.kernel.org/r/5b5cdb520df6d579a6659fbe45ac545628be50e4.1584687545.git.vkor@vkten.inSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

use netdev_err() which is a message printing function specific for network
devices instead of pr_err(), in function netlink_send().
Signed-off-by: Lourdes Pedrajas <lu@pplo.net>
Link: https://lore.kernel.org/r/20200320003947.31726-1-lu@pplo.netSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove unnecessary braces for single statement block
Signed-off-by: Gokce Kuler <gokcekuler@gmail.com>
Link: https://lore.kernel.org/r/20200320000326.GA9349@siyah2Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Correct typo in two comments.
Misspelling found using checkpatch.pl.
Signed-off-by: R Veera Kumar <vkor@vkten.in>
Link: https://lore.kernel.org/r/1ea4ff5dedf35b51afc53866c303b62a66caff7d.1584633953.git.vkor@vkten.inSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In some platforms gpio's are not used for reset but
for other purposes. Because of that when we try to
get them are valid gpio's but are already assigned
to do other function. To avoid those kind of problems
in those platforms just notice the fail in the kernel
but continue doing normal boot.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200319161416.19033-1-sergio.paracuellos@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit.  Fix it by replacing with scnprintf().
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-rpi-kernel@lists.infradead.org
Cc: devel@driverdev.osuosl.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200319161300.25967-1-tiwai@suse.deSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Instead of being using PCI Configuration and Status Register to
set up virtual bridges we are using CONFIG_ADDR Register which is
wrong. Hence, set the correct value.

Fixes: 9a5e71a6 ("staging: mt7621-pci: simplify 'mt7621_pcie_init_virtual_bridges' function")
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20200319095733.1557-1-sergio.paracuellos@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use ARRAY_SIZE to replace the hardcoded size so we will never have a
mismatch.
Signed-off-by: Oscar Carter <oscar.carter@gmx.com>
Link: https://lore.kernel.org/r/20200318174015.7515-1-oscar.carter@gmx.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a newline after the first argument.
To respect the 80 character line limit.
Found using checkpatch.pl.
Signed-off-by: R Veera Kumar <vkor@vkten.in>
Link: https://lore.kernel.org/r/20200319094835.GA2878@tulip.localSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A simple fix of long line in makefile variable assignment.
Found using checkpatch.pl.
Signed-off-by: R Veera Kumar <vkor@vkten.in>
Link: https://lore.kernel.org/r/20200319095024.GA2970@tulip.localSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixes two long line in Kconfig help.
Found using checkpatch.pl
Signed-off-by: R Veera Kumar <vkor@vkten.in>
Link: https://lore.kernel.org/r/20200319095513.GA3078@tulip.localSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Correct a single typo in a comment.
Misspelling found using checkpatch.pl.
Signed-off-by: R Veera Kumar <vkor@vkten.in>
Link: https://lore.kernel.org/r/20200319093301.GA2453@tulip.localSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Correct a single typo in a comment.
Misspelling found using checkpatch.pl.
Signed-off-by: R Veera Kumar <vkor@vkten.in>
Link: https://lore.kernel.org/r/20200319093715.GA2550@tulip.localSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Correct a single typo in a comment.
Misspelling found using checkpatch.pl.
Signed-off-by: R Veera Kumar <vkor@vkten.in>
Link: https://lore.kernel.org/r/20200319094043.GA2669@tulip.localSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Correct a single typo in a comment.
Misspelling found using checkpatch.pl.
Signed-off-by: R Veera Kumar <vkor@vkten.in>
Link: https://lore.kernel.org/r/20200319094358.GA2751@tulip.localSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Correct a long line in documentation to respect the
80 character line limit.
Found using checkpatch.pl.
Signed-off-by: R Veera Kumar <vkor@vkten.in>
Link: https://lore.kernel.org/r/20200319085751.GA1928@tulip.localSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>